Tent platform – Wikipedia
Platform for a suspended tent Platform for a portable tent A tent platform is a floor that is used for the purpose of pitching one or more tents. In most cases, it is a wooden platform adjacent to a hiking route that gives hikers with a clean and level location to rest their heads. It may help keep the campers from trampling on the nearby plants, which is beneficial. Tent platforms are available at several campgrounds. Mountaineers occasionally construct tent platforms in their base camps out of natural resources like as pebbles or snow.
Tent platforms, which are put on top of vehicles and support roof tents, are available.
References
- “Accessibility Guidebook for Outdoor Recreation and Trails” is a resource for people with disabilities. The Forest Service of the United States. retrieved on October 31, 2013
- Catharine Wells, Aaron Starmer, and Timothy Starmer are all members of the Starmer family (1 June 2007). For car campers who dislike RVs, concrete slabs, and loud portable stereos, this guide to the best in tent camping in New York State is a must-read. Menasha Ridge Press, pp. 47–, ISBN 978-0-89732-641-4
- Boy Scouts of America, Inc., pp. 47–, ISBN 978-0-89732-641-4
- (June 1967). It’s a Boy’s Life. pages. 34–.ISSN0006-8608
- Bonnier Corporation, pp. 34–.ISSN0006-8608
- Boy Scouts of America, Inc. (January 1937). Popular Science, Bonnier Corporation, pp. 38–.ISSN0161-7370
- Doug Matthews, Popular Science (23 May 2012). 288–288. ISBN 978-1-136-36545-4
- Special Event Production: The Resources, Routledge, pp. 288–288. ISBN 978-1-136-36545-4
External links
- The following are examples of tent platforms and related items: floating tent platforms, stacked tent platforms, flooring systems for event tents, etc.
Platform and Deck Tent – FREE SHIPPING
- SHIPPING IS COMPLIMENTARY. A canvas platform tent is sometimes referred to as a deck tent or an off-the-ground tent in some circles. It is most common to utilize an off-the-ground tent if you are planning on putting it in a permanent site. Canvas platform tents and deck tents are essentially the same type of tents that are often seen at Glamping resorts, with the exception of their size. For more information, including prices and photographs, visit glamping tents. Many further examples can be found by clicking campingplatform tent photos, which may assist you in deciding how you want to construct your platform. Tents that are elevated above the ground give a significantly better camping experience. Because you are not on the ground, you will have less mice and snakes to contend with. Additionally, the ground beneath your tent will be level. Additionally, it is easy to channel water away from the tent while it is raining. This decreases the probability of water getting on or under your floor. RECOMMENDATIONS:If you intend to set up your tent on a deck platform, the following are some suggestions: Construction of the platform: Do not begin construction of the camping tent platform until you have received and measured the canvas tent. Tent sizes vary widely, with most canvas tents being either smaller or bigger than the tent’s claimed measurements. Platform Dimensions: Construct the platform to be the same width as the framework. Rainwater runs down the roof over the eaves in this manner, preventing the majority of the water from puddling on the platform and entering the tent. Also, make sure that the deck tent structure is flush with the rear of the platform in order to prevent rainwater from entering from behind. Rainwater gap in platform: If you have a porch area and are using plywood, cut a 1/2-inch space in the middle of the platform “The plywood immediately in front of the deck tent has a gap in it. Rain water will not be able to enter via this opening from the front. Make sure the 2x6s for the porch run parallel to the front of the tent and allow for a 1/2 inch gap between the 2x6s “a space between the boards directly in front of you
- When using frame leg anchors, it is recommended that you use them in order to prevent your frame legs from rolling off the edges of your platform under high-wind conditions. These anchors are screwed into the platform floor and provide extremely sturdy support for your deck tent frame. Leg anchors may be viewed by selectinganchors from the drop-down menu. It is recommended that each tent frame leg be equipped with an anchor. Sod cloth is applied to the inside of the tent on top of the platform. If you do not want the sod cloth to be seen, place it on the inside of the platform on top of the platform. Wind and rain will be kept out by screwing it down with 2x4s. Keep in mind that there will be gaps at the corners due to the fact that sod cloths are cut at each corner. If you like, you can stain the 2x4s. If you want to make your tent wet and bug resistant, you may hang the sod cloth along the edges of the platform and then screw in a 1″ x 4″ board to the platform sides
- However, this is not recommended. Guy’s roping: Installation of eyebolts towards the bottom of the platform, right below the eave D rings or grommets on the sides and rear will be necessary. Attach your man ropes to the eyebolts with a knot. It is preferable to keep the ropes out of your way rather than having them at a 45o angle from the eaves, as described in this approach. If you use this approach, you must have your platform well secured to the ground, or else you risk having your platform and tent snatched up by high winds and blown away. A fly is highly recommended for canvas tents on platforms since they are typically left up for extended periods of time, and a fly is required. The use of a fly will considerably extend the life of your camping tent. It protects the tent roof from damaging UV rays, acts as an additional moisture barrier, stops any stove sparks from burning a tiny hole in your tent roof, and keeps your tent roof clean by removing tree sap and other debris from the tent roof
- Enlarged fly: Some individuals utilize an oversized fly to create a covered sitting space for themselves. Fly-hitching rail (also known as a fly-hitching rail): 4″ higher than the eave and 18″ out from the eave will provide for regular fly overhang on each side of the roof on each side of the roof. Tie the fly ropes over the top of the hitching rail so that they are visible. The hitching rail, which is used to hook your fly ropes to the eave, must be parallel to the eave. The use of this hitching rail will eliminate the need for fly ropes around your tent. Those are the four “A higher hitching rail provides for a space between the tent and the fly, allowing for better air circulation and the drying off of any moisture that may have accumulated on the canvas roof. However, if you anticipate severe winds, do not leave a space between the fly and the tent, since high gusts will demolish the fly and cause it to collapse. Finish by attaching the fly ropes to the hitching rail starting at the bottom, which will close any gaps. Floor:RECOMMENDED, A loose waterproof floor is preferred for off-the-ground tents because it permits the use of a perimeter sill board to tie the sod cloth to the side of your platform, which is more secure than a tight waterproof floor. Rain or snow may find their way inside your canvas tent, making the waterproof floor an absolute must-have if there is any chance of it happening. Whether water is present on your platform or rain may be blown into the tent through the walls, especially at the corners where the sod fabric is broken, water will accumulate in the tent and cause it to flood. You don’t want water getting into your tent, especially if it has carpeting inside. Because you have to remove everything off your floor, dry the carpet, and then reassemble everything in your tent, having a wet carpet is a complete catastrophe. Platform tents are suitable for use with indoor/outdoor carpeting as a floor covering. Having an efficient rain perimeter sill board and a rain gap at the front of your canvas tent can help to keep it dry during rainstorms. When compared to vinyl or wood flooring, carpeting is far more comfortable to walk on. A fireproof material must be placed under your stove and around it by at least 2 feet on all sides. Carpets are extremely combustible, and considerable caution should be exercised when working with them. Always utilize some form of nonflammable material under your stove, preferably one that is 18 inches thick or more “to the front of the line You should only use a carpet at your own risk. Snow accumulations: Some people like to leave their tents up during the winter months. There is no interior frame that can endure the weight of a large amount of snow. Because of heavy snowstorms, I’ve heard of outfitters who were forced to abandon tents in the backcountry over the winter because they needed to get back to the road base camps before the horse trails became impassable. I’ve also heard of outfitters who were forced to abandon tents in the backcountry because they had to leave quickly with their clients in order to make it back before the horse trails became impassable. When the outfitters returned their stuff the next spring, their tents and frames had been ripped to shreds and the frames had been ruined. For those who choose to leave tents up in the winter, I strongly advise using rafters every 2 feet to keep them from blowing away. The fact that your house has rafters every 2 feet to sustain snow loads should be mentioned. In the case of an off-the-ground tent, wood frame against steel frame is preferred. Some of our clients construct a wooden frame. Wood frames are far more difficult to construct than frames constructed from an angle kit and steel pipe. Using an angle kit, you can construct a steel frame in as little as 1-2 hours. The wood frame takes substantially longer to construct and is significantly more complex to construct. Moreover, it is quite difficult and time-consuming to separate wood rafters, wood ridgetent lengths, and wood legs and then use a saw to make modifications before reassembling your frame with nails or screws if your canvas shrinks more than you anticipated. If you are using 2x4s or 2x6s, you must round the jagged edges to prevent fraying of your canvas when it billows in the wind
- Otherwise, your canvas will tear. Frame made of steel: If you need to make alterations to a steel frame, the frame can be disassembled relatively quickly and easily. No tools are necessary to install or disassemble the steel frame, which is slip joint constructed. If you have any concerns about a camping platform tent or a deck tent, please do not hesitate to contact us.
Create A Bell Tent Platform Deck
SHIPPING IS COMPLETELY FREE! An off-the-ground tent, also known as a deck tent or a canvas platform tent, is a type of canvas platform tent. In most cases, off-the-ground tents are utilized when a structure is to be permanently installed. Canvas platform tents and deck tents are essentially the same type of tents that are often seen at Glamping resorts, with the exception of their size. For more information, including prices and photographs, visit glamping tents for more information. A variety of further samples may be found by clicking campingplatform tent photos, which can assist you in determining how you want to construct your platform.
- As a result of not being at ground level, you will have less mice and snakes to deal with.
- Additionally, it is simpler to channel water away from the tent while it is raining heavily.
- ADVICE AND RECOMMENDATIONS: If you want to set up your tent on a deck platform, I have some suggestions for you.
- Tent sizes vary widely, and most canvas tents are either smaller or bigger than the tent’s claimed size.
- As a result, rainwater drains down the roof over the eaves, preventing the majority of it from puddling on the platform and entering the tent in the first place.
- Rainwater will not be able to enter via this opening from the front of the structure.
- Your deck tent structure will be extremely sturdy thanks to the anchors that screw into your platform floor.
On each tent frame leg, it is preferable to have an anchor.
You can place the sod cloth on the inside of the platform if you don’t want it to be visible.
Also, keep in mind that when sod cloths are cut at each corner, there will be gaps between them.
If you want to make your tent weather and bug proof, you may hang the sod cloth down the edges of the platform and then screw in a 1″ x 4″ board to the platform sides; however, this is not necessary.
Eyebolts are where you’ll tie your man ropes.
Because of the nature of this approach, it is essential that your platform be well fixed into the ground, otherwise you risk having your platform and tent carried up by high winds.
Adding a fly to your tent will dramatically extend its lifespan.
Hooking Rail for Flying Objects (Fly Hitch): 4″ higher than the eave and 18″ out from the eave will provide for regular fly overhang on either side of the roof on both sides of the roof.
(See illustration) To connect your fly ropes to the hitching rail, it must be parallel to the eave.
Those are the Four “Because of the increased height of the hitching rail, there is more space between the tent and the fly, allowing for better air circulation and drying of any moisture on the canvas ceiling.
Begin by tying the fly ropes to the hitching rail at the bottom, which will eliminate any gaps.
If there is any chance that rain or snow may seep inside your canvas tent, the waterproof floor is an absolute must-have accessory.
Water should not be allowed to enter your tent, especially if it is carpeted.
Your platform tent may be covered with an indoor/outdoor carpet.
If you compare it to vinyl or wood flooring, carpeting is far more comfortable to walk on.
As a result, considerable caution should be exercised when working on carpets.
Heavy snow loads are not supported by an interior structure, which is a need.
I’ve also heard of outfitters who were forced to abandon tents in the backcountry because they had to leave quickly with their clients in order to make it back before the trails became impassable.
For those who choose to leave tents up in the winter, I strongly advise using rafters every 2 feet to keep them from blowing over.
Timber versus steel frame for off-the-ground tent platform: What’s the difference?
It is far more difficult to construct a wooden frame compared to one constructed using an angle kit and steel pipe.
The wood frame is substantially more time-consuming and complex to construct.
You must round the edges of 2x4s or 2x6s if you are using them since the canvas may tear over time when it billows in the wind.
No tools are necessary for assembly or disassembly of the steel frame, which is slip-jointed.
Selecting a Tent Platform Design
Platforms are available in a variety of shapes and sizes, with no one design being significantly more useful than the others. The most common designs for a 16-foot (5-meter) wood bell tent platform are squares (20’x20′), rectangles (20’x30′), hexagons (11-gons), and orhendegons (11-gons), all of which may be used with or without decks. The design selection that is best for you will be decided by your intended function, shape, and financial constraints. Materials, labor, and design are the three primary factors that influence the cost of a platform.
- The cost of materials increases according to the size of the platform
- Hiring a carpenter is unquestionably more expensive than attempting the project on your own
- In general, the more unconventional your design, the longer it will take to construct (see bullet2)
If your site is not level, you may also need to build footings to your platform, which may necessitate the construction of a stairs to reach to the front door. credit: @amlwarner photo credit: @boulders hideaway photo credit: @amlwarner Photo credit: @DalefarmphotosPhoto credit: @paintrockfarmPhoto credit: @Dalefarmphotos
Tent Deck Material Considerations
Your platform will be subjected to harsh weather conditions, which can vary depending on where you are located. The effects of the sun, rain, snow, and humidity on your platform can all deteriorate its condition over time. Used treated timber and fasteners that are constructed to endure changing weather conditions are suggested for use in this project. In terms of wood for bell tent decks, cedar and redwood are two of the best options, followed by pressure treated wood, which is a more cost-effective alternative.
Anticipated Costs
Materials might cost anywhere from $2,000 to $5,000, depending on the size of your platform, the quality of the wood, and the location of your platform. The cost of labor will also vary based on a variety of circumstances, but it is likely to be between $1,500 and $3,000 per hour.
Securing Your Tent Properly
The procedure of erecting your tent on the platform is largely the same as the process of erecting it directly on the ground. You will, however, need to plan ahead of time how you will attach the guy lines and the floor of the tent to the platform itself in a smart manner. The following steps are used to secure the floor: Once you’ve set up your tent on the platform, the following step is to tie the floor to the deck at each of the four corners, making sure that the floor is taut and free of wrinkles in the process.
- A washer should be used to secure the D-ring of each corner of the groundsheet so that it does not slip over the screw or bolt.
- Another alternative is to use a heavy-duty screw hook as a temporary solution.
- Individuals have just extended their guy lines from the tent and secured them right into the ground just a few feet away from where the platform is.
- In order to ensure that the bell tent is set up on stable ground, the guy lines are intended to be stretched at a particular specific angle from the roof seams.
- We recommend attaching the guy lines to the posts that have been installed to the deck.
- Using this method, you will be able to extend the guy lines at their proper angle while also eliminating any possible tripping hazards.
You could either construct a taller post to support the guy line tied to the door, or you could add a second guy line above the door and tie each end to the posts directly to the left and right of the entrance, as shown in the illustration.
Bell Tent Platform Design Plans by Life inTents
We’ve created some really elaborate bell tent layouts that you might want to consider installing on your deck if you have the space. Our bell tent deck designs are exactly designed to fit the design of a 5-meter (16-foot) bell tent and include a deck off the front entrance for an awning, steps, and sturdy footings to provide a safe and secure structure. We’re glad to provide them for free with the purchase of a canvas tent from Life inTents. 5M people have life intentions. Rendering of the bell tent platform design
Alternatives to a Glamping Tent Platform
If you don’t have the resources to physically construct a platform, or if you only want a temporary protective ground barrier, you might construct a raised and flat rock bed on which to pitch your bell tent instead. We recommend that you use finely crushed rock such as decomposed granite or 14 minus gravel for this project. It should be enclosed with edging that is approximately 2 feet away from the tent’s exterior walls. Place about 1.5″-2″ of the material on top of the previous layer, packing the rock down between every 0.5″ layer.
Please feel free to share your thoughts and suggestions with us!
How to Overland in Style – Stay Luxurious on the Road
In terms of comfort, overlanding is not often linked with luxury. After all, you’ll be travelling great distances and squeezing in a lot of stops. In terms of comfort, overlanding is not often linked with luxury. After all, you’ll be travelling great miles and sleeping in your car or a tent on your journey. Because overlanding may be really pleasant and sumptuous, you’re incorrect in this assumption. THE BOOK SELECTION The 12th of January, the year 20 Read for 228 minutes
Start A Mobile Glamping Business in 2022
Glamping event providers and backyard glamping enterprises began to spring up in the Wes boroughs in the year 2015. Mobile glamping enterprises are in high demand right now, surpassing their supply, making this a fantastic small business opportunity in your local community. We want to assist you in determining whether or not it is the right moment for you to start your own glamping rental business.
How to Pitch a Tent on a Wooden Platform
The 9th of January in the year 2021 Frequently Asked Questions are included below. Many state parks, national forests, and national parks offer campsites with wooden tent platforms, which may be found in a variety of locations. Anyone who has attempted to pitch a tent on one of these will understand how difficult it can be, especially if you are using a tent that is not self-supporting and requires tent stakes to be erected. These wooden platforms are generally equipped with metal anchors or loops that are situated around the perimeter; however, they are only useful provided you remember to bring along extra guylines that are long enough to reach them.
- Most wooden camping platforms, on the other hand, are covered with parallel planks that have spaces between them to prevent water from accumulating on top of the platform when it rains.
- These tent anchors are ideal for use when erecting tents on wood platforms.
- Pictures on the left and right depict the top and bottom of the anchor, respectively, while pictures on the right depict how the anchor should be placed in the space between two boards.
- According to the thickness of the guylines you have, there are a variety of applications for them.
- These tent anchors are lightweight, weighing only 8 grams apiece, and are small enough to fit in your stake pack if you anticipate needing to sleep on a tent platform in the future.
Furthermore, they are quite inexpensive (11 dollars for ten anchors), making them extremely convenient for the pocketbook. I believe they are an excellent low-impact option and have a strong preference for them for this application.
See also:
- Is it necessary to have a tent footprint when backpacking
- What are the advantages and disadvantages of using trekking pole tents
- How to Prevent Condensation in a Tent
- A Guide to Setting Up a Tent on a Wooden Platform
- What to Do If Your Backpacking Tent Is Wet
About the author
Creator of SectionHiker.com, which is well-known for its backpacking gear reviews and hiking FAQs, Philip Werner has walked and backpacked over 7500 miles throughout the United States and the United Kingdom, and has authored over 2500 articles in his capacity as the site’s founder. Hiking and backpacking enthusiast from New Hampshire and Maine, Philip is the 36th person to travel all 650 trails in the White Mountain Guide, a distance of nearly 2500 miles. He plans to complete a second cycle of hiking trails in the White Mountain Guide in 2021.
- Backpacking the White Mountain 4000 Footers is available for download here.
- NOTE FROM THE EDITOR: If you’re considering about purchasing gear that we’ve reviewed or recommended on SectionHiker, you may contribute to our fundraising efforts.
- Simply click on any of the vendor links provided above.
- Thank you for your assistance, and please know that we appreciate it!
How to Build A Wall Tent Platform
Construction of a wooden or concrete platform to act as a base will provide the most enjoyable canvas wall tent experience possible. Although we’ll be using a 12′ x 16′ platform as an example in this post, the measurements are easily adjusted for whatever wall tent size you want. You can also discover designs for our most popular wall tent sizes farther down on this page. Watch this short movie to get an insight of the platform-building process in action.
What you’ll need
Before you begin building, gather the following materials, which can be acquired at any local hardware shop with relative ease.
hardware
- (1) Post top connection (Yardistry YP21012)
- (18) Joist hanger for single 2′′ x 6′′
- (1-2 boxes) exterior wood screws or nails
- (1) post top connector (Yardistry YP21012)
Foundation
- Flat surface
- (9) 4′′ x 4′′ posts, trimmed to length
- (1 bag) gravel fill
- (1-2 bags) concrete, for a more stable foundation
- (1-2 bags) concrete
- (9) Concrete deck blocks (for use only on a slanted surface)
BeamJoist
- (2) 2′′ x 6′′ 16′ beams
- (3) 2′′ x 6′′ 12′ beams
- (18) 2′′ x 6′′ 8′ joists
- (2) 2′′ x 6′′ 16′ joists
Floor
- A total of 36 deck or composite floor boards measuring 5/4″ x 6″ x 12′
Setting the posts
- Locate a level surface and outline a 12-by-16-foot space for the platform. In order to accommodate beams, posts must be placed 1 1/2″ from the outer corners. Locate the Middle Posts in accordance with the dimensions provided below. It is recommended that the center post be 5 1/2″ shorter than the rest of the columns in order to allow the center beam, which will rest on the post top connector. Once the location of the posts has been determined, dig a hole at least 6″ deep. Place the post in the ground and cover with gravel to improve drainage.
Attaching the perimeter
- Reduce the length of two shorter beams to 11’9″
- Reduce the length of two longer beams to 16′
- Reduce the length of one short middle beam to 11’2″ Exterior beams should be screwed directly into the post using galvanized wood screws. Check to see if they are level. For a short beam, place (2) joist hangers within the middle columns. (Optional) A Post Top Connector measuring 4″ by 4″ should be placed in the center of the central column. Install a small beam on the center column between the two middle columns to provide additional support.
Adding the joists
- Find the middle of the short center beam and use it to determine the joist spacing. Once the center has been determined, make a mark at 16″ on center for the remainder of the joists. Install joist hangers on both sides of the short central beam, where the joists will be suspended
- And Install the joists in the joist hanger and secure them with wood screws. Screw straight from the beam to the joists on the outside of the structure.
Placing the floor boards
- It is possible to utilize pressure treated wood deck board or composite deck board for this project. Deck planks should be cut to 12′ in length. Lay out the boards to check that they all fit on the platform without the need to rip the boards — If all boards are consistent 5 1/2″ in width, all boards should fit on a 12′ x 16′ platform without gaps between the boards. The floor planks should be fastened to the joists using screws.
Application of platform deck boards in 1216
adding an Outrigger
Once your platform is complete, you may add an outrigger to make your canvas wall tent experience even more enjoyable and memorable.
Still looking for the perfect wall tent?
Get started by looking through our most popular canvas wall tent designs. After all, adventure is only around the corner.
RV.Net Open Roads Forum: Tent Camping: What is Platform Camping?
I ran across Platform camping sites at a state park in Georgia. Do you pitch your tent on the platform? If so how do you stake it down? Looks interesting but just don’t know anything about it. Could be great for early tent camping when the ground is too damp or cold for comfort. Look forward to some insight. | Yep they are for tents but I think they are sometimes hated for the amount of cord needed for set up etc. I have never been on one but I think they want to minimize damaging more of the plant life. Even on dirt they often want the tents to set up in the same area to minimize damage. | I suppose it would depend upon the campground, but from my understanding, a tent is already installed on a platoform or a deck. Some can get pretty elaborate, including king size beds, dressers, tables, lights and chairs. This is actually called”Glamping”.Others are more primative where you have to set up your own tent. Most tents today are 100% free standing, held up by fiberglass flexible poles put together in a criss-cross fashion to hold the tent upright. Usually small stakes are pushed in the ground to keep the tent from blowing around. On a platform where you supply your own tent, I am sure there is a way to tie the corners down so the wind won’t blow it away. Looking at some different internet sites, one person blogged he brought his own wood-screw eyelets to screw into the wood to tie the tent to.I don’t think this is a a good idea unless you actually own the platofrm.Anywhere, here’s a bunch of internet photos:”Platform tenting”.EDIT:The idea of “platform tenting” has been around for quite a long time. At Fort Benjamin Harrision (North East of Indianapolis), which is now a State Park and no longer a military post, you can still see the original concrete pads which were poured in the early 1930’s. Below is an old photograph of the pads from that time era. Below that is a portion of a map of the military post. The little squares all aligned dress-right-dress are the concrete pads.Today if you visit the park, these pads are outside the park office. Although some are crumbled, they are still there. If you notice, or if you go in person, they were constructed with rebarb eyelets to tie the tents down. These are not used for camping any more. Fort Harrision State Park has no overnight camping anywhere. I think they are working to create a campground. It sure would be nice if they allowed tents to be pitched atop these pads again and bring back some of the nostalgia form the days when this military post was used in it’s height of glory!Here’s a photo from Bing Maps (Birdseye view) of the same spot as it looks today.* This post waslastedited 02/26/15 07:35pm by DutchmenSport * | Here you go;Okefenokee swamp platform camping
This member is not responsible for opinions that are inaccurate due to faulty information provided by the original poster. Use them at your own discretion.09 SuperDuty Crew Cab 6.8L/4.10(The Black Pearl)06 Keystone Hornet 29 RLS/(The Cracker Cabana) |
Spent the summer of 1966 working at local Boy Scout Camp. Earned $50 total for the 8 weeks plus tent and board. Staff camping area was platforms and wall tents. Tents were slightly larger that the platforms, dry floors were nice. |
Deck Plans
Deck DesignsIvy Fife2021-12-20T11:59:47-07:00
Deck Plans
You may set up your tent on a platform that fits the footprint of the tent, or you can extend the deck to create a front porch, which will provide you with some really usable outdoor living area. Building the platform can be done by you or by a third-party contractor. You have the choice to choose. But don’t forget to put your unique stamp on it! We supply some basic drawings for your platform tent, as well as the necessary measurements. You have the option of customizing your platform and ridge pole to suit your needs and tastes.
- Quality and craftsmanship are the fundamentals. What is Involved in a Yurt Construction Project
- Request a Brochure
- Request Fabric Samples
- Return to the Home Page
- The following options are available: Yurt Covers
- ColorFabric Selector
- Doors
- Windows
- Domes/ Skylights
- WindSnow Insulation
- The Back.
- Interior Design Ideas
- Floor Plan Examples
- Deck Designs
- Back to top of the page
- Pitch a Yurt, Engineering, Building Energy Codes, Technical Support, and more are all available here.
- Quality and craftsmanship are the fundamentals. Exactly what goes into a Tipi project is unknown. Request a Brochure
- Return to the Home Page
- TIPI COVERINGS
- INTERIOR CLOTH COMPONENTS (LINERS, OZANSFLOR COVERS)
- POLES + ACCESSORIES
- PAINTED TIPIS
- DECK DESIGNS
- PHOTO GALLERY
- BACK
- Tipi Pricing
- Tipi Pitching
- Visiting a Tipi
- Tipi FAQs
- Back to top of page
- Instructions for Pitching
- Care and Cleaning
- Technical Support
- Return to top of page
- Quality and craftsmanship are the fundamentals. What is Involved in a Tent Construction Project
- Requesting a Brochure
- Returning to the Home Page
- Deck Plans
- Framework
- Gallery
- Back
- Tent Covers
- Tent Options
- Measurements
- Deck Covers
- Prices for tents
- Pitching tents
- Visiting a tent
- Tent Frequently Asked Questions
- Back
- Instructions for Pitching
- Care and Cleaning
- Technical Support
- Return to top of page
- Pricing for Yurts
- Pricing for Tipis
- Pricing for Tents
- Blog
- LOGO WEAR
- Back
- Fabric samples can be requested, as well as a brochure. Technology, specifications, and support for yurts
- Technology, specifications, and support for tipis
- And technology, specifications, and support for tents
- PHONE 970-240-2111
- KEEP UP TO DATE Sign up for our email list to receive the newest news
- GET IN TOUCH
- GET SOCIAL
- GET BACK TO
Why Does The Glamping Tent Need A Platform
14th of October, 2019 Choosing a flat open piece of land to set up your glamping tent on when you want to use a mountaintop as a vacation destination is the first step in creating your resort. However, it is possible that this will not be as simple as it appears. If you are fortunate enough to locate a field in which to pitch a tent, you must also consider whether the rain will flow back into the tent when it rains, which is a consideration. If you have come into this crazy when attempting to set up a glamping tent, you will need a platform to assist you in resolving the situation.
- With a platform on which to set up the glamping tent, you can concentrate on choosing the ideal viewing position on the mountain without having to worry about whether or not such an ideal viewing location can also be utilized to construct a tent on the mountain.
- Of course, it doesn’t matter if it’s grass, a level surface, a beach, or a mountain.
- The platform does an excellent job of keeping your tent dry.
- if your tent is erected directly on the ground, the moisture from the earth will eventually erode into your tent, causing the furnishings to get moldy.
- All of this has an impact on your mood when on a camping trip.
- A platform 20-30 cm above the ground should be built, as this will effectively keep moisture from the earth from entering your tent.
- Make use of the platform to advocate for the preservation of the natural environment.
- While using the platform, it is possible to lessen the influence of the tent on the surrounding environment while not causing an excessive amount of damage to the natural environment itself.
- The glamping tent may be secured to the platform with more sturdiness.
- Setting up a glamping tent on the platform might assist you in solving a variety of challenges.
Not only do you not have to be concerned about the position of the tent, but you also don’t have to be concerned about the luxury tent being destroyed by rain or its influence on the natural environment. So, with confidence, choose the glamping tent of your choice and begin planning your holiday.
Tent Platforms: A History of Personal Forest Preserve Leases –
Several years ago, my wife, our Newfoundland dog, and I were paddling on Long Pond in the St. Regis Canoe Area when we came upon what looked to be a large number of very artificial clearings. I I across a piece of plastic water pipe or an old rusted pipe that seemed like it could have been a dock support here and there, half submerged. They are the ruins of tent platform sites that were once there. These campgrounds were constructed on “forever wild” New York State Adirondack Forest Preserve Lands in the early 1970s under leases to private persons on the lands of the Adirondack Park.
- The Lower Saranac Lake area, where there were 187 tent platforms leased in 1961, as well as the several ponds that presently make up the St.
- There were also tent platform sites available on famous lakes such as Forked, Seventh, Lewey, and Indian Lakes, as well as along the Raquette River and at a variety of other locations across the area.
- There were various provisions in the application to which the applicant was required to adhere, and these were listed below.
- Docks were only allowed to be three feet wide and no longer than 20 feet in length.
- In terms of platform size, the average was 16’x20′, or 320 sq ft.
- All rubbish or trash had to be buried or hauled away from the location (regulations frequently ignored).
- Each lease had to be renewed on an annual basis, according to the terms of the agreement.
Commissioner of the New York State Parks and Recreation Department, George Pratt (1915-1921), intended to expand recreational possibilities in the early twentieth century.
He also created the tent platform leasing system, which allows users to construct a standardized timber platform with wooden sides that is then covered with canvas on a rental basis.
The leasing scheme has gradually expanded over the years.
Camping, hiking, and canoeing were all popular activities.
“The tent platform permission system constituted a ‘holding’ on state lands,” said one of the most vocal critics.
The Adirondack Park Agency was established by an act of the New York State Legislature in June 1971.
There are other suggestions in the report, including the establishment of the current land-use categories of Wilderness, Wild Forest, Canoe Area, and Primitive Area, which would be phased in by 1975.
The Tent Platform Association was formed, and meetings were conducted at the Saranac Lake Fish and Game Club to discuss the organization’s goals (notably where early support for the opening of Forest Preserve land to snowmobiles had also been organized).
They petitioned the American Psychological Association, the Department of Environmental Conservation, as well as local and state legislators.
The Association declined.
Their advice was that lessees or sub-leaseholders should make preparations to remove any personal goods and platform from their properties before the deadline.
Many former permit holders had clung to their positions, appealing to the APA, the Governor, their politicians, and just holding out in the hope that something would change.
The cleanup was entrusted to the Department of the Environment work crews, volunteers, and prison workers.
Stoves, sinks, mattresses, propane tanks, and other metal items were dragged out by snowmobile, along with other items.
A large number of old tent-platform sites have been converted into basic campsites.
There are still some concrete stairs on Polliwog Pond that are tucked away in the trees.
If you know where to look for it, that is.
When traveling in big groups or for a longer period of time than 14 days, it is still feasible to get a “temporary revocable permission” via a local Forest Ranger.
Typical Standard Tent PlatformFrame (1956), courtesy of the Adirondack Mountain Club archives; Tent Platform permission sign1386 (courtesy of Joel Reber, Lewey Lake); and a former Tent Platform Site on Forked Lake, courtesy of the Adirondack Mountain Club archives (Mike Prescott photo).
Mike Prescott
Mr. Mike Prescott, a retired history teacher and secondary school principal, has discovered an exciting new retirement career in kayaking the Adirondack rivers and learning about their history. The Adirondack Mountain Club and the Northern Forest Canoe Trail are among Mike’s volunteer activities. He is also a New York State Licensed Guide and works with the Raquette River Blueway Corridor, the New York State Trails Council, and the Northern Forest Canoe Trail. Please do not hesitate to reach him at View all of the posts made by
GFC Platform Tent
A enjoyable time outside is impossible if you’re too exhausted to operate properly. That’s why we designed the Platform Tent to provide you with the relaxation you require when you’re out in the field. You’ll be able to re-enter civilisation more quickly, get your task done more quickly, and return to your feral state as soon as possible. When it comes to waking relaxation, the 4-foot head height will have you lying in luxury, whether your eyes are captivated to the scenery or the pages of Steinbeck and Hemingway’s novels.
If the weather is pleasant, you’ll appreciate the cooling cross ventilation provided by the zip-and-roll screens, and if a storm is raging outside, you’ll be blissfully unaware of the wind.
With all of that luxury, you might be tempted to finish off your banquet beer with a pinky out, as if you were at a glamping site or something similar.
How to Build Your Own Portable Tent Platform
It may seem strange, but a significant part of tent camping and living in the outdoors is about being able to comfortably separate your body from the elements of nature while yet being immersed in them. Consider the implications of this. Make sure you have the appropriate apparel to keep you warm and dry in the rain and cold. You prepare a tent to provide shelter for the night. You’ve even laid down ground tarps and sleeping mats to better insulate and shield yourself from the elements. Because we humans are rather fragile when compared to all that nature may hurl at us, it only makes sense to construct and maintain certain barriers to keep us safe from harm.
There are times when the ground is perfectly pebbled with sharp pebbles wherever you look, and other times when the entire landscape is nothing but marsh.
For some campers, this is simply a fact of life that must be endured; for others, a movable tent platform may be utilized to their advantage. When you’re attempting to camp in rough or damp terrain, ground tarps and sleeping pads can only go you so far in terms of comfort.
Why build a portable tent platform
The main benefit of a portable tent platform is the ability to have convenience and comfort whenever and wherever you want it. It is especially beneficial if you anticipate spending a significant amount of time in your tent. More permanent tent structures, such as yurts, tipis, and canvas tents, are frequently placed on wooden tent platforms, and camping platforms have become increasingly popular in the world of glamping, or luxurious camping. Even if sleeping on a tent floor over rough terrain and uneven ground, or waking up fatigued to find a flooded tent, the novelty of such an experience quickly wears off.
- Despite their expertise, even the most experienced campers have their limits.
- Those traveling by vehicle will quickly discover that a tent is far more comfortable, while those traveling in RVs may require a “extra room” of some form depending on the amount of people traveling.
- Those who will be sleeping in the tent will be really grateful.
- This manner, you can quickly put it where you want it, pitch your tent on top of it, and then go from there if you so choose.
- In addition to long-term visitors, this is also significant for campers who are substantially older or younger than the average age.
- In comparison, the experience of someone in their 80s or even a toddler-aged camper is vastly different.
- The use of a portable tent platform is highly recommended if you anticipate camping with anyone who would benefit from an additional layer of protection from the weather.
How to build a portable tent platform
There are a number various ways to construct a portable tent platform, and each one is dependent on your definition of portable as well as your understanding of what constitutes a decent platform. It has been recommended on certain online forums that all you need is two foldable tables put up side by side and you’ll have all you need.
This is not true. Of course, you are allowed to experiment with this, but it is not suggested. In this section, we will discuss two approaches to developing a platform that is more resilient and helpful.
Building a removable tent platform for a trailer
One of the most effective methods of constructing a portable tent platform is to place it on top of a trailer. There are several changes and building options available to you as a result of the readily transportable and robust basis on which you may build your structure. This example will show you how to build a temporary tent platform on top of a 4′ by 6′ trailer, which will be described in more detail later. The finished product is large enough to accommodate a conventional 7 × 7 tent and is constructed in such a way that storage space can be found beneath the platform.
- When going on a road trip or vehicle camping, all you have to do is pull over, set up your tent, and you’re ready to go.
- So, in order to construct this platform, you will first require a few components.
- It may be any size you choose; all you have to do is make the necessary modifications to your own build.
- For a trailer that is 6 feet long, you will need at least 51 feet of lumber.
- That’s all there is to it for the wood you’ll need.
- You’ll need a package of wood screws to help you put everything together when you’ve finished.
- After all of this, the only thing left to figure out is what you’re going to use for the outside supports, which we’ll cover in a bit more detail later.
- You will, however, require some basic equipment to make the process simpler.
Construction of the removable tent platform for a trailer
As soon as you have all of your materials available, it will be time to begin construction. The first item that has to be constructed is the platform’s foundation. The trailer’s base is constructed of three 2×4 supports that run the length of the trailer. One on either side of the room and one along the center. These supports will be used to attach the entire platform to the ground. A 6′ long trailer will require nine 2×4 pieces along the length of the trailer’s interior, with each section measuring 6′ in length.
- After that, you’ll need to cut fifteen support struts from the 2x4s you’ve gathered.
- To ensure a level trailer, the top piece of 2×4 should be level with the top edge of the trailer’s sides.
- As soon as you have screwed all of these 2×4 pieces together and placed them in their proper locations, you are ready to proceed.
- In order to create an inner platform, you will need to join two of the 48 boards together.
- You will still be able to lift the boards to gain access to the storage area beneath them.
- The remaining hinges will be used to join each part to the inner platform once it has been assembled.
- In order for these outboards to be able to fold inward, the hinges should be strategically placed.
- Due to the fact that these outside boards will be a little unsteady, you will need to construct legs for them.
- Some people have been inventive with similar ideas, and they have utilized chair legs, table legs, and even old walkers as structural support for their creations.
Whatever you choose to utilize, you’ll need something to assist support the outside platform, regardless of what you choose. You are now finished with your trailer tent platform for your portable tent platform!
A simpler construction
For those of you who find the trailer platform construction too time-consuming or who prefer not to have something constructed on top of a trailer, this next project is for you. It doesn’t get much more straightforward than this. Once again, this design is intended for a traditional-sized two-person tent, but you may modify it to meet your specific requirements by adding more space. You may potentially construct multiples of these platforms and arrange them next to each other on a flat surface.
- Two 48-inch sheets should be plenty.
- Aside from that, you will just require basic woodworking equipment such as a drill and a circular saw.
- Caution should be exercised when connecting the boards.
- Attach the hinges equally spaced around the centre of the sheets so that the sheets fold inward when the sheets are folded.
- When it is fully unfurled, the 2×4 base should provide sufficient support for your requirements.
- If you so like, you may also make a few modifications to this design.
- Additional 2x4s or even strong PVC pipe will suffice in this situation.
- This is a great opportunity to be creative, but just adding some hinged pieces of plywood with folding legs would suffice.
Modifications for your tent platform
Once you have invested the necessary effort to construct a DIY portable tentplatform, you can begin to enjoy it to its full potential. If you look around the platform, you’ll see that there are several small things you can make to improve its functionality and convenience of use. Here, we’ll go through some of the small details that, while simple to execute, can have a significant impact on overall operation. As you continue to work with the platform, you will undoubtedly come up with new ideas, which you should consider putting into action.
- Short imitation grass can be purchased at places like Home Depot, and it is simple to install.
- If you prefer wood, you may put higher-quality boards over the plywood sheets and even place a weatherproofing layer on top of that.
- The installation of stairs or even a tiny ladder is another lovely feature that people prefer to have in their homes.
- This may be accomplished by using miniature pool ladders or folding metal stairways, among other things.
- After a long day of trekking that has left you feeling particularly exhausted and worn, you’ll appreciate the fact that your tent is only a handful of little steps away.
- The movable tent platform for a trailer is equipped with hinges that allow you to access the area beneath it, but you can do much more with it.
- You may get creative with other ways to gain access to the space beneath your platform if you choose.
Attachment points for baskets and other add-ons, as well as hooks for displaying items, are all options.
As your DIY carpentry and construction abilities improve, you will notice an increase in the number of options for creativity and originality.
There are a variety of battery-powered outdoor lighting choices that you may incorporate into the platform.
Beyond simply being aesthetically pleasing, this also serves as a valuable source of illumination when camping, making the platform and tent more visible at night.
With the addition of carpets, stairs, additional holding places, and lights, the movable tent platform transforms your tent into a true home-away-from-home experience for guests.
You now have yourself a camping front porch. Alternatively, a gas-powered or do-it-yourself camping stove, as well as a cooler, may be used to create an outdoor kitchen. An advantage that may be capitalized on time and time again is the availability of a movable tent platform.
Final Verdict:
With a few basic carpentry skills and a little imagination, you can construct a portable tent platform that is both sturdy and functional. Camping will become a far more relaxing experience as a result of the platform. With only a few inches of wood and a few hours of construction work, you will be able to get away from tough terrain, flooded campsites, pests, and animals. You will be able to take full advantage of the wonderful outdoors. A tent platform, such as this one, may also be a really wonderful way for less experienced campers, elderly campers, and very young campers to enjoy camping without having to rough it as much as they would otherwise.
Even if you don’t have one, you can still construct an excellent tent platform.
Do you have any suggestions about how to make it more helpful and comfortable for yourself?
Regardless of the platform you create, make it yours.
