How To Restring Tent Poles

How to Replace a Tent Pole Shock Cord

The elastic shock cord on your tent poles has deteriorated and has become brittle, making it no longer flexible. Given that new poles can cost up to $100 or more, why not simply replace the cord, which costs less than ten percent of the price of new poles? It’s been years since I’ve used my North Face Rock 22 two-person tent (which has two identical poles), and the elastic cord within the poles has become brittle and no longer retains its flexibility. I had purchased the tent brand new for around $200, and replacement poles were going to cost an additional $150!

I just needed 30 minutes and a pint of beer to get my tent poles back to their original condition!

You’ll need at least the whole length of all of your poles combined to complete the task.

a pair of scissors or a knife Sharpie or Marker for Measuring Tape Matches or a lighter are recommended.

Step 1: Cut the Cord and Remove the Grommet Pegs

Take a deep breath in and out. Pulling two parts of the pole apart and cutting the rope will do this. This will cause the pole to divide into its distinct parts (Mine has 8 sections per pole, and only the two end sections are different, so I made sure to keep those separate). Remove the peg from the pole end and you should be able to see the standing end of the cord, which has been knotted and linked to the peg. Because my pegs were threaded, I had to detach them from the pole sections in order to use them.

Step 2: Measure Your Pole(s)

Following that, you’ll want to take measurements of your poles so that you can determine how long your cord should be. Because my tent has two poles that are exactly the same length, I only had to measure once. If you have many poles of varying lengths, you will need to repeat this step for each pole in your set. Measure the length of your pole from end to end; this will be the length of your rope when it is fully stretched. My experiments with the elasticity of the cable led me to the conclusion that for every foot of relaxed cord, I would receive 1′-4 of length “because of a stretched chord To get the final length (the length of the pole, hence the ultimate stretched length), we must multiply it by 75% of the original length.

Take the length of your pole in inches and multiply it by 0.75.

My poles are 152 inches in length, hence my measurement is as follows:152 inches * 0.75 inches = 114 inches” This is the spot where I put my relaxed chord marker.

Please keep in mind that you should not cut the cord just yet! It is quite difficult to feed a 114″ cable into a 152″ pole because of the length difference. Inquire as to how I know this.

Step 3: Thread Your Peg and Knot the Cord

Feed the standing end of the cable (the end that is marked with a ‘zero’ on the tape measure) through the hole in the grommet peg and secure it with a rubber band. Draw the thread through a basic binding knot about 2 inches from the end and tighten it. Your peg should now be in the middle of the knot and the long end of the rope, as seen below. In order to avoid tripping, feed the cord through the first part of pole and continue until all portions are attached to the cord. Check to see that the pole portions are aligned appropriately so that they will fit together as intended before continuing (male end toward female end for each joint).

The long end of the cord should be stretched so that it reaches the mark you created earlier while the pole pieces are joined in the manner in which you would build the tent.

In this stage, the pole should be beginning to take form.

Step 4: Cut/Singe the Cord and Insert the Pegs

Remove the cable from the machine, leaving around 2 inches of standing end. Make a singing sound with the lighter or matches at the end of each string (on both ends of the pole). Fold the cord over upon itself and put the standing end of the cord into the pole to complete the loop. Incorporate the knot into the pole. Insert the peg into the pole with the threading needle. Each pole should be treated in the same way.

Be the First to Share

There are various little components in a tent that might fail, but these do not need the purchase of a completely new unit. Tent pole shock cords are susceptible to failure, deterioration, and brittleness with time, and finally loss of their elastic qualities. Your tent pole may no longer operate properly if the shock cord is no longer functioning properly. You may believe that new tent poles are required. Purchasing new tent poles, on the other hand, may be quite expensive, and there is a lot more affordable option.

It is simple to replace the shock cord in your tent pole; all you need are a few simple components and a positive mindset.

We’ll also talk about why shock cords are vital, as well as some preventative actions you may do to avoid more harm.

If you know how to mend a broken tent pole in the field, a broken tent pole in the field does not have to be a reason for panic.

What is a tent shock cord and why is it important?

Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.

Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.

Although you may use a non-elastic shock rope to hold your tent poles together in one piece, the elasticity is undoubtedly advantageous when putting together your wilderness shelter.

What you need to replace the shock cord in a tent pole

Make sure you have all of the materials you’ll need before starting to work on your tent repair. A replacement shock cord may be purchased at your local camping store, and there are several companies who sell shock cords online as well. You will require the following materials:

• The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
• Scissors or a sharp edge
• Measuring tape
• Sharpie or marker pen
• A lighter or matches to melt the ends of the wires Tape for masking

How to replace a faulty shock cord in a tent pole

The moment has come to get started on mending your shelter now that you have all of the equipment you need, as well as some new shock cable to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will see that your tent pole will come apart into its many components after the cable has been severed.

• Because it’s probable that the pole portions in the middle are similar, the end pieces where the rope is knotted are the most critical parts to avoid getting mixed up in the process.
• Perhaps you’ll need to remove your grommet pegs and then untie the remaining cable before you can continue.
• 2.
• Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
• Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
• If you are unable to use your previous cord as a reference, measure and mark the new cord to be approximately 8 inches shorter than the pole, or around 75% of its overall length.
• You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.

Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.

Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.

Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.

When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.

When you’ve reached the desired length with the string, tie a knot here to ensure that the peg is secure.

Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.

All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable inside a tent pole.

All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.

The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.

If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.

How to Repair a Shock Cord if it Breaks in the Field

A snapped or overstretched shock cable might make erecting your shelter more difficult if you’re already out on the trail during your camping vacation. If you want to repair the wire without having to replace the entire length, fortunately, there is a simple solution. However, while this is not a permanent solution, it will allow you to use your tent for a short period of time until you can replace the cord completely. If the cable hasn’t snapped, but rather has become too stretched out to go around your tent pole, there’s a simple solution.

• Then, draw the shock cable through the grommet peg until it is taught once again, and reattach it to the grommet peg.
• If the shock cord on your old tent pole has snapped, you’ll need to remove the pole using the steps outlined above to fix the problem.
• Remove a few inches of the cord’s elastic core on each side of the break, leaving only the braided sheath on the other side.
• The reason you need a thinner segment of cord to tie the knot is so that the knot will not become trapped in the poles and will be able to flow through freely.

Using string as a temporary replacement for a broken shock cord

If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can purchase a new replacement cable. Although this will not have the same elastic characteristics as real shock cable, it can be used as a temporary replacement until you can make more serious repairs. Keep this in mind when using this. All you need to execute this DIY patch is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a small number of supplies.

• Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
• Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
• This will make it much easier to thread the string back through the tent.
• Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
• Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
• Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.

When you’re finished, we recommend that you unfurl your poles to make sure there’s enough slack to pack away your tent properly. Any mistakes can be corrected by untying the end at a peg and making any required modifications.

How to repair a broken tent pole

The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a damaged tent pole as well as changing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.

1. Purchasing a repair sleeve is a cheap option if your tent does not come equipped with one; you never know when you might require one.
2. If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
3. If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
4. Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.
5. Using duct tape, secure a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did previously.

Preventing damage to your tent poles in the future

If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.

When building your tent and connecting the tent poles, start with the central segment and work your way out from there.

This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.

You’ll be considerably more likely to prevent repairs and replacements in the future if you follow these few simple suggestions. If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.

Final Verdict:

It is occasionally required to replace the shock cord in your tent pole, but it does not have to be a difficult process. It is possible to save a large amount of money by making minor repairs and replacements to your camping equipment over time, and it is also considerably healthier for the environment. Learning how to execute these little repairs is simple, and more importantly, it will make you a more experienced camper. As an added bonus, watch this video for some further tent pole repair advice!

How To Restring Tent Pole

To complete this project, you’ll need a shock cord (1/8′′ or smaller). You’ll need at least the whole length of all of your poles combined to complete the task.

Can you fix a broken tent pole?

A pole repair sleeve is the quickest and most convenient method of repairing a damaged pole. This little tube, which is also known as a splint, is frequently included with your tent. If you don’t already have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not move about too much.

Do tent poles need the elastic?

Regarding a gear concern, the “string” that runs through the tent poles The shock cable may be removed and thrown away with less effort and weighs less. It is completely ineffective.

How do I put up a tunnel tent by myself?

How to Set Up a Tunnel Tent (with Pictures) Prepare the location of your tent. Locate a location that is as level as feasible. The tent should be unfolded. This is where having a groundsheet or tarp comes in in, especially if the weather has been very drizzly. The tent should be unfolded. Tent poles should be inserted. Ensure that the tension in the poles is taken up. Raise the tent to the proper position. Prepare the tent by pinning it down. Set up the inner tents on the ground.

What is a tent ferrule?

When two composite rods or tubes are joined together, ferrules are utilized to link them together. They also make it possible to employ shorter carbon or fiberglass rods or tubes, as well as to construct and dismantle your finished product, resulting in a smaller container for transportation purposes.

How do you cut a Fibreglass pole?

Align the rear edge of the fine-toothed hacksaw blade with the pencil mark using a straightedge and a level. Allowing the hacksaw to slowly move toward you and then away from you will allow you to cut through the fiberglass stick. Cutting should be continued until the fiberglass stick is divided into two halves. To finish the cutting operation, remove the masking tape off the fiberglass stick and discard it.

What do you do with a broken tent?

Continue to: Repurposing Is the Most Effective Option. Recycle your tent by purchasing it from an online retailer. At a yard sale or garage sale, you may recycle your tent. Make Use Of A Local Recycling Center To Dispose Of Your Tent. Thrift stores are excellent places to recycle your tent. Don’t throw your tent in the trash or recycle it. Make Use of Your Old Tent for Indoor Recreation.

Can one person set up a 4 person tent?

Easy to assemble, the Core 4-Person Instant Tent accommodates four people comfortably.

As the name indicates, it is practically instantaneous. To set up the tent, all you have to do is unfold it and extend the poles until they snap into position. It is quite simple, even for novices, and takes just a few minutes to complete.

Can I cut a fiberglass tent pole?

What is the best method for cutting fiberglass tent poles? Without a doubt, a basic hacksaw. If you don’t already have one, you’ll soon realize that you’ll need one. Masking tape a few loops around the area you wish to cut, then do it outside. It will take around three minutes total.

Why do my tent poles keep breaking?

Strong winds, poles that have been weakened with age, and inexpensive materials are all potential causes—and occasionally it’s just plain old wear and tear.

Do they sell tent poles?

A set of two REDCAMP Aluminum Tarp Poles that are heavy-duty and adjustable, measuring 35 inches to 90 inches (75″ to 86 inches) in length, and are designed for use with tarp canopies and awning shelters.

Do graphite rods break easily?

The fact that they are as robust as nails does not mean that they are readily broken. However, don’t tempt fate by being disorganized when it comes to arranging your fishing rods.

How do you cut fiberglass without splinters?

Place masking tape along the cut line of a panel, mark the line on the tape using a pencil, then saw through the tape to reduce chipping and splintering. Inside corners cut in a panel should be rounded to prevent a fracture in the completed item as a result of a sharp corner.

How do you dispose of old tents?

In fact, there are 15 innovative methods to reuse an old festival tent that you should check out. Keep an eye on your plants. Make use of natural elements in your landscape. Make your own gazebo out of wood. Make some bags. Ponchos should be made. Fly a kite in the air. They can be used as groundsheets. Protect your upholstered furniture with these pads.

Can one person put up a tent?

There is absolutely no need to be afraid. Despite the fact that dome tents appear to be tough to put together by oneself, they are actually one of the simplest tents to put together! Installing a dome tent is now easier than ever before if you have a recent model on hand.

Can you fix a tent pole with duct tape?

In a pinch, duct tape may be used to repair a damaged tent pole, but this is only a temporary remedy and should not be relied upon. Using duct tape, just wrap the break until it is strong enough to hold the weight of your tent. With order to provide more support, you might apply an improvised splint before covering the break in tape.

What’s the easiest tent to put up?

What is the quickest and most straightforward tent to erect by yourself that we recommend? For Backpacking, the best option is the Teton Sports Instant Tent (1/2 Person). Core Instant Cabin Tent for up to 9 people. The best all-around tent. The Vango Dart Pop Up is a little inflatable boat that can be taken anywhere. Tent for three people. Wenzel Klondike is a fictional character created by author Wenzel Klondike. Tent for eight people. 2/3/4/6 Person Coleman Sundome Dome Tent (Coleman) Vango Airbeam Odyssey Air 500 Villa Tent is a Vango Airbeam Odyssey Air 500 Villa Tent.

Can you buy the top half of a fishing pole?

In most cases, getting a new rod will be more cost effective than repairing an old one, unless you have a heritage rod or need to have the rod butt fixed. There are a plethora of various types of “2 part fishing rods” available. It is preferable to get a new rod that is suitable for your planned application. I hope this has been of assistance.

What are flexible tent poles made from?

Tent Poles Made of Glass Fiber Because of the inexpensive cost of glass fiber, it is a common choice for less budget tents due to its durability.

Because of its flexibility, a tent bends with the wind rather than standing hard against it, allowing it to shed gusts. When you are experiencing something for the first time, it might be a little unnerving.

How do you remove a ferrule from a tent pole?

Place the pole in a vice and heat the ferrule’s tip with a heat gun, grabbing the ferrule with pliers as it heats up, and turning it to check if it starts to move. It is important not to overheat the pole since this will cause it to burn.

How do I repair the shock cord at the center of my pole?

This page was last modified on Tuesday, March 9, 2021 at 10:26 a.m. If you have a shock cord that has become stretched out, gone slack, snapped, or is just worn out and in need of replacement, you have come to the proper spot to get it replaced. This is really a fix that can be completed rather fast and simply at home with little tools. Quest Outfitters carries shock cord, which can be obtained at most hardware stores, outdoor retailers such as REI and Moosejaw, and sporting goods stores.

DIY Shock Cord Replacement

You will need 1/8″ thick shock cord that is around 1-2 feet longer than the length of the complete pole for each pole (for example, if you have a 10ft pole, obtain roughly 12ft; others think a 34% ratio may be preferable.).

1. The shock cord will be wound in a knot once the end tip has been removed (either on a washer or on the end tip of the pole). Cut the knot and you’ll be able to remove the shock cord with ease. The most essential thing to remember is to remove the pieces of each pole in the same sequence that you removed them. After you have removed the old shock wire, you will be ready to thread the new shock cable on each pole. Remember to string them back together in the same sequence. Gently push the shock cord through the entire length of the pole, then tie it off at one end (either with a simple knot or with a loop attached to the pole tip)
2. Then, to tension the shock cord, pull out about 25% of the total length of the pole in slack (for a 10ft pole, pull out 2-3ft), and tie it off at the pole end. After that, you may check the tension and make any required adjustments
3. The pole parts should softly seat themselves. Keep in mind that this is not an exact science, so use your best judgment and common sense while making decisions. Remove any extra shock cable after that, and you’re finished

Here’s a link to a fantastic tutorial from REI that goes over the process of fixing tent poles and includes a part on how to restring shock cord at the base of the pole: Fixing a Tent Pole (with Pictures) Did you find it to be of assistance? Yes NoFeedback is not required.

How do I replace the shock cord in my pole?

Please click here to get a PDF version of these instructions. a fresh length of shock cable 70 percent the length of your pole is cut from the existing length To prevent the line from fraying within your pole, we recommend heating the ends of the cord to seal them and prevent fraying. Place the pole in the desired position and pull one of the pole’s end-stops out until the knot in the shock cord is revealed. If necessary, you can use pliers to remove the end-stop out of the way. To release the end-stop, untie or cut the knot on the end-stop.

1. Remove the end-stop by untying or cutting it.
2. Check to see that the end-stop is completely seated.
3. Thread as many portions as feasible onto the shock wire while still leaving a few inches of shock cord exposed at the end.
4. 5: Tighten the shock cord and secure it with a peg or similar item tied to the shock cord with an easy-to-release knot to prevent it from slipping back into the sections.
5. Continue to thread the remaining portions onto the shock cord, making sure to seat them as you go.
6. Remove enough shock cord to allow you to knot the end-stop on with your fingers.

How do I pitch a Hilleberg tunnel tent?

• Begin by installing the poles, making certain that all of the parts are properly seated together. To set up the tent, start at one of the sides and put a pole into the pole sleeve just above the pole tensioner, sliding it all the way to the other end
• Then, with the pole end that is closest to you inserted into the pole tensioner cup, pull the webbing until the edge of the tent reaches the holder, and repeat the process. Repeat the procedure described above with the remaining pole parts. To set up a tent like the Keron, which has two similar entrances, either end can be staked down first
• To set up a tent like the Keron, grip the front corners and draw the tent out taut, then peg them down. When putting the tent up for the first time, it is best to relax the adjustable peg attachments so that they are at their greatest potential length. It is usually recommended that you man out your tent so that you may attain more tension later on. This is especially vital if there is going to be wind or if the weather is going to be terrible
• Nonetheless,

As the inner and outer of your tent are meant to be pitched together, you won’t need to take them apart unless you choose to pitch one of them independently.

For more thorough instructions relating to your tent, please go to the pitching instructions website, where you may see videos of each tent being pitched and obtain a PDF of the instruction book that came with your tent, among other things.

How do I pitch the inner tent separately?

• To begin, detach the toggles on the inner tent and pull it out of the way. Prepare the inside tent by laying it out. Attach the pole holders (which may be ordered separately) to the toggles on the sides. Using the elastic shock cords as guides, you can now slide a pole across the canvas and into the pole holders on either side of the tent. On a tunnel tent, repeat the operation with the opposite pole(s). Using the inner tent as a guide, tie a guy line to each pole at the top of each side of the inner tent and peg them out to help you build it. The Akto, Allak, Soulo, Staika, and Tarra tents require separate pole holder kits that include additional webbing to attach the pole holders to the tents
• The Akto, Allak, Soulo, Staika, and Tarra tents do not require separate pole holder kits. Please refer to the tent descriptions to see how many pole holders are required for your particular tent type.

To begin, unhook the toggles on the inner tent and pull it out. The inside tent should be laid out. Then attach the pole holders, which may be purchased individually, to the toggles on the sides. Using the elastic shock cords as guides, you can now slide a pole across the tent and into the pole holders on each side of it. To construct a tunnel tent, repeat the procedure with the opposite pole(s). Using the inner tent as a guide, tie a guy line to each pole at the top of each side of the inner tent and peg them out to help you build it.

It is important to check the tent descriptions to see how many pole holders are required for your tent model;

My tunnel tent is noisy, in strong winds, what can I do?

Begin by unhooking the toggles on the inner tent and removing it. Prepare the interior of the tent. Attach the pole holders, which may be ordered separately, to the toggles on the sides. Using the elastic shock cords as guides, you can now slide a pole across the tent and into the pole holders at each end. On a tunnel tent, repeat the procedure with the opposite pole(s). Tie a guy line to the top of each pole of the inner tent at the front and back of the tent to help you build the tent; Individual pole holder kits that include extra webbing to attach the pole holders to the Akto, Allak, Soulo, Staika, and Tarra tents are required for use with these tents; the Allak, Soulo, Staika, and Tarra tents do not require any additional pole holder kits.

How tight should the door band be on my tent?

The door band’s function is to maintain the door of your tent at the proper size so that the zippers may operate properly. It is made of nylon. A tight enough door band is required to ensure that there is no stress across the zippers in order for this to be accomplished. The door band, on the other hand, should not be overtightened to the point where the door hangs freely when the door is closed.

How tight should the ground straps be on my tunnel tent?

When using our tunnel tents, the ground straps assist in maintaining the right height and tension of the poles. When they are properly fitted, there should be no stress on the connections that join the inner and outer tents caused by the poles themselves. Because of the excessive tension created by the ground strap, the poles will be put under unneeded stress, and the inner tent will droop inwards at the sides.

My tent has seen a lot of heavy use, how can I re-treat the fabrics?

In addition to being extremely robust, our textiles are also waterproof and highly water-repellent. Sun, wind, rain, and wear, on the other hand, will deteriorate any cloth with time. More information on how ultraviolet light may degrade textiles can be found here. Re-treating the fabric will increase both the protection against UV damage and the water repellency of the fabric, but it will have no effect on the tear strength of the cloth. Restoring the condition of your outer tent The Nikwax TentGear SolarProof, which is simple to apply and does not contain fluorocarbons, is the product we suggest for re-treating our outer tent materials.

TentGear SolarProof should be sprayed or brushed over the cloth, and any surplus liquid should be wiped away.

Please keep in mind that TentGear SolarProof should not be used on a new tent, but rather on a tent that has lost its water resistant capacity over time.

Restoring the condition of your inner tent Nikwax TX may be used to restore the water repellency of your inner tent after it has been exposed to the elements for an extended length of time.

Spray the TX with the same method as with TentGear SolarProof. Directly after, wipe away any extra liquid and allow it to dry. We encourage you to visit if you would like additional information about these items as well as information on where you can purchase them.

My tent is dirty. How do I clean it?

Setting up your tent and then cleaning it with a sponge and lukewarm water after your journey is a wonderful idea once you return from your adventure. We strongly advise against the use of any cleaning chemicals. Using a tiny brush, thoroughly brush the zippers to ensure that no sand or grit is left in the teeth of the zippers is also essential. Sand in the zippers can wear out the sliders, preventing them from functioning correctly again after they have been cleaned. Check and double-check that your poles and pegs are clean and free of damage before using them.

If the tent is really unclean and dusty, we usually wash it in the washing machine.

No matter how you clean it, be certain that the tent is totally dry before putting it away for the season.

How do I use a line runner?

1. To loosen the Line Runner, use your fingers to draw the line away from the Line Runner’s body, as indicated in the illustration. Pulling the line into the Line Runner’s channel will secure it in place.

My pole broke, what do I do?

One extra pole piece as well as a repair sleeve are included in each pole bag for convenience. In the meanwhile, you may use the repair sleeve to temporarily fix your pole until you get an opportunity to replace the damaged pole segment. To get a PDF with step-by-step instructions on how to repair a tent pole, click here. Making use of a repair sleeve Twelve. Slide the sleeve over the damaged pole and center it over the damaged area, then tape the ends of the sleeve together to secure it in place.

1. Pull the end-stop of the pole out until the knot in the shock cord is visible.
2. 2.
3. Untie the knot and remove the end-stop off the cord to complete the process.
4. Pull the pole apart to reveal the shock cord that is hidden underneath the broken piece of the pole.
5. 4.
6. Keep track of the order so that you can replace them in the proper sequence.
7. 6.
8. Reattach the end-stop to the shock cord with a knot.

My zipper doesn’t work, how do I fix it?

When there is a problem with a zipper, the first clue that anything is wrong is that the zipper will not remain closed when you try to zip it closed. What generally causes this is dirt and grit in the zipper, which wears microscopic grooves on the inside of the zipper slider as a result of the zipper being used. You may make a temporary repair by pinching the edges of the zipper slider together until you have the opportunity to replace it. It is critical to clean your zippers on a regular basis in order to avoid this from happening.

• In order to replace the zipper sliders, first open up the stitches at one end of the zipper and then remove the little metal clip that is attached to it.
• Remove the old sliders by sliding them off.
• Install the new sliders by sliding them on and making sure that they are facing in the same orientations as the previous ones.
• Double-check that the sliders are aligned appropriately, not only in the front and rear but also in the top and bottom.
• It might be difficult to put the slider on with the flat end first on some occasions.
• 6) Once you’ve begun to slide the zipper slider along the zipper, continue to pull on either side of the zipper to complete it.

7, 8. Once the sliders are in place and functioning properly, rejoin the stitches you undid and sew a few stitches to seal the end and prevent the sliders from coming loose again. Reset the metal clip if at all feasible.

How do I attach a line runner?

When there is a problem with a zipper, the first clue that anything is wrong is that the zipper will not shut when you try to zip it closed. Dirt and grit in the zipper, which causes microscopic grooves on the inside of the zipper slider to wear away, is typically the source of this problem. You can make a temporary repair by pinching the edges of the zipper slider together until you have the opportunity to replace it. – Regular cleaning of your zippers is essential in order to avoid this from occurring in the first place.

1. In order to replace the zipper sliders, first open up the stitches at one end of the zipper and then remove the small metal clip that is attached to them.
2. Remove the old sliders by sliding them off the track.
3. Install the new sliders by sliding them on and ensuring that they are facing in the same orientations as the previous ones.
4. 5.
5. Ensure that you begin with the zipper teeth zipped together while doing this operation.
6. After the sliders are in place and functioning properly, rejoin the stitches you undid and sew a few stitches to seal the end and prevent the sliders from coming loose.
7. It is best if the metal clip can be repositioned.

How do I attach the Footprint?

The best time to attach your Footprint to your tent is just before you want to go camping. Lay your tent out on the floor with the floor facing up if you’re indoors. The Footprint should be placed directly on top of the tent floor with the logo side facing the floor, and its logo should be aligned as follows:

• If the Footprint extends into the vestibule, the logo or logos on the Footprint should be aligned with the centre of the main outer tent door or doors if the Footprint covers the vestibule. Keep in mind that the main door on the Kaitum GT and Nallo GT is the large entrance, rather than the small entrance near the front of the extended vestibule
• If the Footprint does not cover the vestibule, the logo on the Footprint should align with the logo on the inner tent door
• The Rogen is an exception to this rule due to its asymmetrical design. When the Rogen Footprint logo is displayed, it should be in alignment with the logo that appears on one end of the Rogen outer tent.

Look on the back of the Footprint’s hang tag for specifics about your particular tent model. Once the Footprint is properly oriented, attach the toggles that are located around the circumference of the Footprint to the rings that are located at the bottom border of the outer tent’s bottom edge. When the tent is fully assembled, the reflective side and logo should be facing upward. When you pack up your tent at the end of a trip, you may leave the Footprint still connected. Just make sure that the entire tent, as well as the Footprint, is totally dry before putting it back in its place.

Why do the footprints on the Anjan, Rogen, and Niak tents not cover the vestibule?

The optional Footprints do not cover the vestibules on the Anjan, Rogen, and Niak tents since the outer tents do not extend all the way to the ground on these three models.

During heavy rains, water can seep into the vestibule through the space between the outer tent wall and the ground in the vestibule. If the Footprint covered the vestibule area, water may seep below the tent and cause it to collapse.

My tent is paler after a lot of time in the sun, what happened?

In addition to being extremely robust, our textiles are also waterproof and highly water-repellent. Sun, wind, rain, and wear, on the other hand, will deteriorate any cloth with time. A faded or bleached appearance to the fabric indicates that the cloth has begun to be affected by ultraviolet rays. UV rays from direct sunshine have negative effects on our skin, and the same is true for all materials, including tent fabrics (which is terrible). With prolonged exposure to the sun’s radiation, particularly at altitude and in the southern hemisphere, the performance of a cloth can be compromised.

1. Extended exposure to ultraviolet radiation (UV) weakens the tear strength of any fabric, which is one of the primary reasons we employ materials with high tear strength.
2. This, on the other hand, does not imply a deterioration in the fabric’s waterproofing properties.
3. More information on how to withdraw your tent may be found here.
4. Pitching your tent in the shade with a tarp over it and not keeping it set up during the day while you aren’t using it can help you achieve this.

How do I roll my outer tent door?

We recommend rolling the door in a certain manner rather than just bundling it and securing it with the toggle because it works better to keep it out of the way, it is more secure, and it keeps the door and zipper from dragging in the mud, which will extend the lifetime of your tent. To roll the door, begin by rolling the fabric of the door in the direction of the toggle. As you continue, collect the cloth toward the toggle by folding the loose end of the roll in and gathering the fabric. One of the objectives is to bring the main body of the door, including the zipper’s end, beneath the toggle.

Pull out the elastic loop and thread it through the toggle when you have the door fully rolled.

Tips for rethreading elasticated tent poles?

GreetingsElastic threaded through one of the poles of my family tent has been kapput. Do you have any suggestions for rethreading it? First, use a coat hanger to make a thin cord, then thread some shockcord through it. 3mm? It will be quite a ball pain because it contains 8 or 10 pieces. thanks In response to toiksander: Is it possible to use gravity and a safety pin on a thread to draw new cable through? In response to toiksander: I’ve done this a zillion times, and you’ll find that the shock cord can be pushed through the poles while giving them a slight twist as you do so.

1. 1) Thread the elastic through the first pole and tie off one end of the elastic to keep it from coming out.
2. 3) Tighten the elastic until it is taut, then clove hitch the tensioned elastic to something sturdy, such as a pencil.
3. You may also insert a large safety pin into the elastic to prevent it from retracting farther.
4. Repeat steps 3 and 4 until all of the threading is complete, and then make a knot in the elastic to prevent it from retracting.
5. Gavin Post was modified at 14:31.
6. That’s exactly what I was thinking.
7. It is difficult to untie once the knot has been strengthened.

Take note of whether the shock cable is connected into a detachable end piece on the pole; this is typically very lightly cemented in place to prevent it from falling out.

Keep old tents free of poles and bring them in for repairs on a regular basis.

In response to Brownie: you may use a long length of bent wire to accomplish your goal.

Captain Paranoia received the following response: Heavier sea fishing nylon line was the only thing I was able to get through the fiberglass type pole I was using.

As long as you can attach the shock cord to the end of it, it will operate well, and it is simple to push through the pole.

The metal and huge pole sections have been covered by the majority of these.

Heat Make a larks foot and a seal at the end of the elastic, then stitch a portion of yarn that is longer than the pole as close to the end of the elastic as possible to ensure that the elastic pulls straight.

Keep the cordage and pole in a straight line to avoid damaging the pole end or abrading the yarn, which will cause it to snap (later) If you do, a consistent, solid pull will get you through to the finish line.

and then repeat the process If you still have the old elastic inside the pole, could you hook the new bit to the end of it and pull it through? In response toiksander: This subject has been archived and will no longer accept new posts in response to it.

Amazon.com : tent pole shock cord

Hello, the elastic threaded through one of the poles of my family tent has kapputted together. Do you have any suggestions for rethreading the threading machine? First, use a coat hanger to make a thin cord, and then thread some shockcord through it. 3mm? This one includes 8 or 10 sections, so it’ll be a real ball pain to go through it all. thanks Toiksander’s response: Is it possible to use gravity and a safety pin on a thread to draw in new cord? Toiksander’s response: If you follow my instructions, you’ll discover that the shock cord may be pushed between the poles while giving it a slight twist as you go.

1. In order to prevent it from pulling through the first pole, knot one end of the elastic off.
2. Step 3: Tighten the elastic until it is taut, and then clove hitch it to something sturdy, such as a pencil.
3. To prevent the elastic from retracting further, you can alternatively insert a large safety pin through it.
4. 4) To finish threading everything, repeat steps 3 and 4 until everything is threaded.
5. A ten-minute work should be enough time to complete.
6. Regarding Gavin’s response: A ten-minute work should be enough time to complete.
7. However, I would offer one more suggestion.

It is difficult to untie a knot that has been strengthened previously.

Take note of whether the shock cord is tied into a detachable end piece on the pole; this is typically very lightly cemented in place to prevent the cord from falling out.

Keep old tents free of poles and bring them in for repairs on a regular basis!

You may use a lengthy piece of bent wire, in response to Brownie’s question: Pole kits I’ve purchased have included a long, thin, rigid wire that’s been wound around a wooden dowel.

Paranoia was given the following response.

It’s been more than 30 years since I used it for sea fishing, but I believe it was 30lb breaking strain line at the time.

It is also simple to push through the pole.

The metal and huge pole sections have been covered by the majority of them.

Heat Make a larks foot and a seal at the end of the elastic, then stitch a portion of yarn that is longer than the pole as close to the end of the elastic as possible so that it pulls straight when pulled.

Ensure that the cordage and pole are in a straight line in order to avoid damaging the pole end or abrading the yarn, which will result in the yarn snapping (later) You’ll get there if you maintain a steady, hard pull.

happy camping, and repeat If you still have the old elastic inside the pole, could you hook the new bit to the end of it and pull it through? In response toiksander Comments on this topic have been archived and will no longer be accepted.

GOLBERG Elastic Shock Cord – 2.5mm, 1/32, 1/16, 3/16, 5/16, 1/8, 3/8, 5/8, 1/4, 1/2 inch diameter – Various Colors – 10, 25, 50, 100 ft lengths – Made in the USA (Neon Orange, 3/16in x 25ft)

Ships to the Netherlands are available. Only 6 of these items are left in stock – purchase soon. Ships to the Netherlands are available. There is just one left in stock, so act quickly. Brands that are associated with your search

How to Replace the Shock Cord in Tent Poles ?

If the following instructions from Sierra Designs for changing the shock cable for an SD Dome tent (original) are helpful, please see below: Hello, Elliot. You may absolutely restring them at your convenience: 1). A set of poles, shock cord (which can be purchased at practically any outdoor shop or online), a table vice, two hammers or a hammer and a mallet, forceps or needle nose pliers, and a pair of needle nose pliers are all necessary tools. 2). Determine the sort of tip that will be used on the poles of your model.

• a).
• I Position the pole so that the tip end is sticking out of the table vice (position it with cloth or a towel around the pole, and very lightly secure it into place) ii).
• iii).
• Some types feature an anchor washer within the last segment of the pole, so if the tip of the pole does not appear to be linked to the cable, don’t be concerned.) b).
• c).
• Insert a new line of shock cord immediately back through the holes created by the removal of the tips and the pulling out of the faulty chord.
• If it was a press-fit, tap the end tip back into place to secure it, just as you did when you removed the cord.
• With the remaining end open and free of a tip and shock cable dangling from it, clamp the shock cord just where the pole terminates and extend an arm’s length directly away from the pole to create a straight line.
• If the cable is stretched too far, it will break much more quickly.
• If you are having difficulty understanding the arms-length description, a yard is a decent measurement to use.

Secure and squeeze the shock cord at the point where the pole terminates with forceps while maintaining that arm’s length of stress on the pole (so that it cannot retract back into the pole) I Remove the remainder of the cord beyond the forceps, but allow enough to make a knot to complete the task at hand.

Tie the remaining anchoring knot to the pole’s tip or to the washer within the pole, depending on which is most convenient (varies on models) iii).

After tying to the tip, when you remove the forceps, the tension should nearly completely reattach the cord and tip to their original positions, although they may need to be screwed or tapped in place. g). Pour yourself a drink.

How to Fix your Pole Set

Ever returned to camp after a long day on the trail to discover your tent overturned and your pole set a complete mess of shock cord and poles? If so, you’re not alone. Hopefully, the response is negative. However, occasionally a storm or a stray wind gust might have a negative impact on your tiny home away from home. Fortunately, our staff here at NEMO has prepared for the worst, and your tent comes with a pole splint that can be found within the pole bag. Here’s what you’ll need to accomplish in order to go through the rest of your journey: 1.

1. Locate the pole splint and the broken pole segment in your pole set by following the arrows. The pole splint should be pushed up the poles until it is covering the fractured pole piece. Make use of duct tape or repair tape to keep the pole splint firmly attached to the pole set. You can use a pole set until you’re able to return home and do a more thorough repair. Watch this video for a brief instruction on how to use it.

At-Home Repair

Once you have returned home, please contact our customer service department. Because pole segments are removable, you won’t have to replace the entire pole set if one segment breaks. If you have any questions, please contact us at 800-997-9301, or fill out our Spare Parts Obtain Form to request a pole section. In either case, they’ll be pleased to assist you in restoring your pole set to full functionality in preparation for your next expedition. Although disassembling a pole set might seem scary if you’ve never done it before, it should be a simple and quick operation as long as you follow the steps in the instructions carefully and thoroughly.

This chart may also be used to keep track of your progress once you have received the replacement pole section and are ready to begin the repair.

Once you’ve received the new pole segment, follow the step-by-step process below for replacing it in your pole set:

1. Remove the ball cap from the end of the pole that is closest to the damaged segment. After that, detach the ball cap from the shock cable with a screwdriver. Remove the ball cap from the pole by unscrewing it and pulling it away from the shock cord. 2: Untie the shock cord loop so that the shock cord may be readily threaded through the poles. One of the most common NEMO tent components, this three-pronged hub links the shock cable to the hub through a little black clip that can be taken out of the middle of the hub.

1. 3.
2. You may put a number on a piece of paper (or directly on the pole itself in marker) and name the poles as they come off the shock cord with that number as they come off the cable.
3. 4.
4. 5.
5. 6.
6. 7.

Special Instructions: Hubs

For damaged pole segments that need the removal of the shock cord from a central hub, this is the most effective procedure for restoring the hub to working condition. One of the most common NEMO tent components, this three-pronged hub links the shock cable to the hub through a little black clip that can be taken out of the middle of the hub.

Three-pronged hub: The Dagger, Aurora, Hornet, Hornet Elite, Firefly, and Dragonfly are all equipped with this hub, as are the Hornet and Aurora. One portion, the ridge pole of the tent, is joined to the other half by a little black clip, which is used to tie the shock cord to the hub of the tent.

The easiest way to remove this black clip is to:

1. To reach the shock cord of your pole set, use a sharp blade to go under the lip of the black hub covering and through the opening. It should easily pop out of the hub; we recommend removing both sides at the same time. With care, insert a blade between a lip on the hub covering and raise to release the cover. 2. Carefully pull the shock cable away from the black clip, allowing it to completely detach from the hub. This will assist in loosening the clip just enough to allow it to be removed.

1. In order to remove this clip, we recommend pushing it out via one side of the center hub aperture with a pen; do not hesitate to apply pressure because the clip is quite tough.
2. After that, you should be able to work it out far enough to be able to grip the other end with your fingers.
3. After you’ve finished repairing your pole set, thread a loop of shock wire through the hub leg until it pokes out of the centre of the hub.
4. 6.
5. 7.
6. To make a loop, feed the shock cable through the hub, then attach the black clip to the shock cord and pull the clip back into position in the hub to complete the loop.

Loose Shock cord? No problem!

Over time, shock cord’s elasticity might deteriorate as a result of its use. In the event that you observe fraying, loss of elasticity, or that the poles do not fit together correctly, it is critical that you replace the shock cord in your pole set. Shock cord may be found at most sporting goods stores and on the internet. You can also get in touch with us personally if you require shock cords. Following the installation of your new shock cable, you’ll want to disassemble your pole set according to the instructions provided above.

Do you have a question?