How To Repair Tent Pole Shock Cord

How to Replace a Tent Pole Shock Cord

The elastic shock cord on your tent poles has deteriorated and has become brittle, making it no longer flexible. Given that new poles can cost up to $100 or more, why not simply replace the cord, which costs less than ten percent of the price of new poles? It’s been years since I’ve used my North Face Rock 22 two-person tent (which has two identical poles), and the elastic cord within the poles has become brittle and no longer retains its flexibility. I had purchased the tent brand new for around $200, and replacement poles were going to cost an additional $150!

I just needed 30 minutes and a pint of beer to get my tent poles back to their original condition!

You’ll need at least the whole length of all of your poles combined to complete the task.

a pair of scissors or a knife Sharpie or Marker for Measuring Tape Matches or a lighter are recommended.

Step 1: Cut the Cord and Remove the Grommet Pegs

Take a deep breath in and out. Pulling two parts of the pole apart and cutting the rope will do this. This will cause the pole to divide into its distinct parts (Mine has 8 sections per pole, and only the two end sections are different, so I made sure to keep those separate). Remove the peg from the pole end and you should be able to see the standing end of the cord, which has been knotted and linked to the peg. Because my pegs were threaded, I had to detach them from the pole sections in order to use them.

Step 2: Measure Your Pole(s)

Following that, you’ll want to take measurements of your poles so that you can determine how long your rope should be. Because my tent has two poles that are exactly the same length, I only had to measure once. If you have many poles of varying lengths, you will need to repeat this step for each pole in your set. Measure the length of your pole from end to end; this will be the length of your rope when it is fully stretched. My experiments with the elasticity of the cable led me to the conclusion that for every foot of relaxed cord, I would receive 1′-4 of length “because of a stretched chord To get the final length (the length of the pole, hence the ultimate stretched length), we must multiply it by 75% of the original length.

Take the length of your pole in inches and multiply it by 0.75.

My poles are 152 inches in length, hence my measurement is as follows:152 inches * 0.75 inches = 114 inches” This is the spot where I put my relaxed chord marker.

Please keep in mind that you should not cut the cord just yet! It is quite difficult to feed a 114″ cable into a 152″ pole because of the length difference. Inquire as to how I know this.

Step 3: Thread Your Peg and Knot the Cord

Feed the standing end of the cable (the end that is marked with a ‘zero’ on the tape measure) through the hole in the grommet peg and secure it with a rubber band. Draw the thread through a basic binding knot about 2 inches from the end and tighten it. Your peg should now be in the middle of the knot and the long end of the rope, as seen below. In order to avoid tripping, feed the cord through the first part of pole and continue until all portions are attached to the cord. Check to see that the pole portions are aligned appropriately so that they will fit together as intended before continuing (male end toward female end for each joint).

The long end of the cord should be stretched so that it reaches the mark you created earlier while the pole pieces are joined in the manner in which you would build the tent.

In this stage, the pole should be beginning to take form.

Step 4: Cut/Singe the Cord and Insert the Pegs

Remove the cable from the machine, leaving around 2 inches of standing end. Make a singing sound with the lighter or matches at the end of each string (on both ends of the pole). Fold the cord over upon itself and put the standing end of the cord into the pole to complete the loop. Incorporate the knot into the pole. Insert the peg into the pole with the threading needle. Each pole should be treated in the same way.

Be the First to Share

There are various little components in a tent that might fail, but these do not need the purchase of a completely new unit. Tent pole shock cords are susceptible to failure, deterioration, and brittleness with time, and finally loss of their elastic qualities. Your tent pole may no longer operate properly if the shock cord is no longer functioning properly. You may believe that new tent poles are required. Purchasing new tent poles, on the other hand, may be quite expensive, and there is a lot more affordable option.

It is simple to replace the shock cord in your tent pole; all you need are a few simple components and a positive mindset.

We’ll also talk about why shock cords are vital, as well as some preventative actions you may do to avoid more harm.

If you know how to mend a broken tent pole in the field, a broken tent pole in the field does not have to be a reason for panic.

What is a tent shock cord and why is it important?

Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.

Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.

Although you may use a non-elastic shock rope to hold your tent poles together in one piece, the elasticity is undoubtedly advantageous when putting together your wilderness shelter.

What you need to replace the shock cord in a tent pole

Make sure you have all of the materials you’ll need before starting to work on your tent repair. A replacement shock cord may be purchased at your local camping store, and there are several companies who sell shock cords online as well. You will require the following materials:

  • The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
  • Scissors or a sharp edge
  • Measuring tape
  • Sharpie or marker pen
  • A lighter or matches to melt the ends of the wires Tape for masking

How to replace a faulty shock cord in a tent pole

The moment has come to get started on mending your shelter now that you have all of the equipment you need, as well as some new shock cable to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will see that your tent pole will come apart into its many components after the cable has been severed.

  1. Because it’s probable that the pole portions in the middle are similar, the end pieces where the rope is knotted are the most critical parts to avoid getting mixed up in the process.
  2. Perhaps you’ll need to remove your grommet pegs and then untie the remaining cable before you can continue.
  3. 2.
  4. Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
  5. Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
  6. If you are unable to use your previous cord as a reference, measure and mark the new cord to be approximately 8 inches shorter than the pole, or around 75% of its overall length.
  7. You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.

Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.

Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.

Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.

When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.

When you’ve reached the desired length with the string, tie a knot here to ensure that the peg is secure.

Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.

All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable inside a tent pole.

All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.

The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.

If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.

How to Repair a Shock Cord if it Breaks in the Field

A snapped or overstretched shock cable might make erecting your shelter more difficult if you’re already out on the trail during your camping vacation. If you want to repair the wire without having to replace the entire length, fortunately, there is a simple solution. However, while this is not a permanent solution, it will allow you to use your tent for a short period of time until you can replace the cord completely. If the cable hasn’t snapped, but rather has become too stretched out to go around your tent pole, there’s a simple solution.

  • Then, draw the shock cable through the grommet peg until it is taught once again, and reattach it to the grommet peg.
  • If the shock cord on your old tent pole has snapped, you’ll need to remove the pole using the steps outlined above to fix the problem.
  • Remove a few inches of the cord’s elastic core on each side of the break, leaving only the braided sheath on the other side.
  • The reason you need a thinner segment of cord to tie the knot is so that the knot will not become trapped in the poles and will be able to flow through freely.

Using string as a temporary replacement for a broken shock cord

If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can purchase a new replacement cable. Although this will not have the same elastic characteristics as real shock cable, it can be used as a temporary replacement until you can make more serious repairs. Keep this in mind when using this. All you need to execute this DIY patch is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a small number of supplies.

  1. Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
  2. Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
  3. This will make it much easier to thread the string back through the tent.
  4. Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
  5. Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
  6. Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.

When you’re finished, we recommend that you unfurl your poles to make sure there’s enough slack to pack away your tent properly. Any mistakes can be corrected by untying the end at a peg and making any required modifications.

How to repair a broken tent pole

The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a damaged tent pole as well as changing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.

  1. Purchasing a repair sleeve is a cheap option if your tent does not come equipped with one; you never know when you might require one.
  2. If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
  3. If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
  4. Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.
  5. Using duct tape, secure a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did previously.
See also:  How Much Does A Glamping Tent Cost

Preventing damage to your tent poles in the future

If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.

When building your tent and connecting the tent poles, start with the central segment and work your way out from there.

This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.

You’ll be considerably more likely to prevent repairs and replacements in the future if you follow these few simple suggestions. If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.

Final Verdict:

It is occasionally required to replace the shock cord in your tent pole, but it does not have to be a difficult process. It is possible to save a large amount of money by making minor repairs and replacements to your camping equipment over time, and it is also considerably healthier for the environment. Learning how to execute these little repairs is simple, and more importantly, it will make you a more experienced camper. As an added bonus, watch this video for some further tent pole repair advice!

How do I repair the shock cord at the center of my pole?

This page was last modified on Tuesday, March 9, 2021 at 10:26 a.m. If you have a shock cord that has become stretched out, gone slack, snapped, or is just worn out and in need of replacement, you have come to the proper spot to get it replaced. This is really a fix that can be completed rather fast and simply at home with little tools. Quest Outfitters carries shock cord, which can be obtained at most hardware stores, outdoor retailers such as REI and Moosejaw, and sporting goods stores.

DIY Shock Cord Replacement

You will need 1/8″ thick shock cord that is around 1-2 feet longer than the length of the complete pole for each pole (for example, if you have a 10ft pole, obtain roughly 12ft; others think a 34% ratio may be preferable.).

  1. The shock cord will be wound in a knot once the end tip has been removed (either on a washer or on the end tip of the pole). Cut the knot and you’ll be able to remove the shock cord with ease. The most essential thing to remember is to remove the pieces of each pole in the same sequence that you removed them. After you have removed the old shock wire, you will be ready to thread the new shock cable on each pole. Remember to string them back together in the same sequence. Gently push the shock cord through the entire length of the pole, then tie it off at one end (either with a simple knot or with a loop attached to the pole tip)
  2. Then, to tension the shock cord, pull out about 25% of the total length of the pole in slack (for a 10ft pole, pull out 2-3ft), and tie it off at the pole end. After that, you may check the tension and make any required adjustments
  3. The pole parts should softly seat themselves. Keep in mind that this is not an exact science, so use your best judgment and common sense while making decisions. Remove any extra shock cable after that, and you’re finished

Here’s a link to a fantastic tutorial from REI that goes over the process of fixing tent poles and includes a part on how to restring shock cord at the base of the pole: Fixing a Tent Pole (with Pictures) Did you find it to be of assistance? Yes NoFeedback is not required.

How to replace shock cord in tent poles

Have you ever experienced that shaky, jittery feeling in your stomach? I’m talking about the one when your tent poles don’t instinctively want to snap together, but instead stand at attention like slender, lightweight soldiers on display. Even if you’ve owned your tent for a long time and taken it on a number of trips, sooner or later you’ll need to learn how to replace shock cord in tent poles. Here is a video tutorial showing you how to do it step by step. The good news is that changing the shock cable in your tent poles is not difficult to accomplish.

Listed below is the procedure I used to replace the shock cable in my Macpac Sololighttent.

You will need:

  • Repair or replacement shock cord (check with your local hardware store, maritime store, eBay/Amazon, or tent maker for options)
  • Scissors
  • Sticky tape (gaffer tape, masking tape, duct tape)
  • Sharpie

In addition to losing its stretch, this ancient shock cable featured substantial regions of damage where the cord looked to have been welded to itself, which was discovered upon investigation.

Step 1: Remove the old shock cord

The method for gaining access to and removing the cable varies depending on the type of tent. Each end of mine has a straightforward screw top fitting. As an alternative, you may just cut the cord and slip it out from below.

Step 2: Keep the poles in order and number them

Those clever people who design our tents may have specified a certain order in which the poles must be installed in order to guarantee that the tent maintains its proper shape. Consequently, number your poles so that you can quickly put them back together again. much as you would while cheating on a crossword problem.

Step 3: Tie a knot in one end and secure

Taking note of how the maker fastened the final knot may be beneficial so that you may replicate it later.

Remove any surplus material from underneath the knot.

Step 4: Start feeding through your cord

Make your way around to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through until you reach the lug and secure it in place.

Step 5: Continue threading poles in order

Move to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through to the lug and fastening it securely in place with your fingers.

Step 6: Apply tension and hold in place

As you near the end of the rope, you will need to apply some stress to the elastic shock cord in order for it to make it all the way to the other side. While threading the final pole, you’ll need to secure it with some tape to keep it from moving about.

Step 7: Test the tension

Test the tension in your tent poles by bending them into the approximate form of your tent frame before tying everything off at the end.

Step 8: Tie a knot in the end and secure

Secure the end lug with a knot at the end of your cording project. Insert the knot and lug into the end of the pole and tighten them together. Posted on September 13, 2019 in How To by admin

How do I replace the shock cord in my pole?

Please click here to get a PDF version of these instructions. a fresh length of shock cable 70 percent the length of your pole is cut from the existing length To prevent the line from fraying within your pole, we recommend heating the ends of the cord to seal them and prevent fraying. Place the pole in the desired position and pull one of the pole’s end-stops out until the knot in the shock cord is revealed. If necessary, you can use pliers to remove the end-stop out of the way. To release the end-stop, untie or cut the knot on the end-stop.

  1. Remove the end-stop by untying or cutting it.
  2. Check to see that the end-stop is completely seated.
  3. Thread as many portions as feasible onto the shock wire while still leaving a few inches of shock cord exposed at the end.
  4. 5: Tighten the shock cord and secure it with a peg or similar item tied to the shock cord with an easy-to-release knot to prevent it from slipping back into the sections.
  5. Continue to thread the remaining portions onto the shock cord, making sure to seat them as you go.
  6. Remove enough shock cord to allow you to knot the end-stop on with your fingers.

How do I pitch a Hilleberg tunnel tent?

  • Begin by installing the poles, making certain that all of the parts are properly seated together. To set up the tent, start at one of the sides and put a pole into the pole sleeve just above the pole tensioner, sliding it all the way to the other end
  • Then, with the pole end that is closest to you inserted into the pole tensioner cup, pull the webbing until the edge of the tent reaches the holder, and repeat the process. Repeat the procedure described above with the remaining pole parts. To set up a tent like the Keron, which has two similar entrances, either end can be staked down first
  • To set up a tent like the Keron, grip the front corners and draw the tent out taut, then peg them down. When putting the tent up for the first time, it is best to relax the adjustable peg attachments so that they are at their greatest potential length. It is usually recommended that you man out your tent so that you may attain more tension later on. This is especially vital if there is going to be wind or if the weather is going to be terrible
  • Nonetheless,
See also:  Ozark Trail Tent How To Put Up

As the inner and outer of your tent are meant to be pitched together, you won’t need to take them apart unless you choose to pitch one of them independently.

For more thorough instructions relating to your tent, please go to the pitching instructions website, where you may see videos of each tent being pitched and obtain a PDF of the instruction book that came with your tent, among other things.

How do I pitch the inner tent separately?

  • To begin, detach the toggles on the inner tent and pull it out of the way. Prepare the inside tent by laying it out. Attach the pole holders (which may be ordered separately) to the toggles on the sides. Using the elastic shock cords as guides, you can now slide a pole across the canvas and into the pole holders on either side of the tent. On a tunnel tent, repeat the operation with the opposite pole(s). Using the inner tent as a guide, tie a guy line to each pole at the top of each side of the inner tent and peg them out to help you build it. The Akto, Allak, Soulo, Staika, and Tarra tents require separate pole holder kits that include additional webbing to attach the pole holders to the tents
  • The Akto, Allak, Soulo, Staika, and Tarra tents do not require separate pole holder kits. Please refer to the tent descriptions to see how many pole holders are required for your particular tent type.

More thorough instructions pertaining to your tent may be found in the instruction book that came with it, which you can find here. These throwing training books are available for download as PDFs from the pitching instructional website.

My tunnel tent is noisy, in strong winds, what can I do?

Make certain that the tent is correctly pitched and that it is completely taught. When tightening the adjustable pole holders, make sure the outer tent hits the bottom of the pole holder at its lowest point. It is necessary to draw all guy lines to their maximum length and secure them with pegs. It is also necessary to secure the man lines that are linked to the vents. If you are camping in winter circumstances, you may have the benefit of being able to dig a little deeper into the snow before pitching your tent.

Keep in mind that the wind will bring more snow with it and may cause access to get obstructed.

How tight should the door band be on my tent?

The door band’s function is to maintain the door of your tent at the proper size so that the zippers may operate properly. It is made of nylon. A tight enough door band is required to ensure that there is no stress across the zippers in order for this to be accomplished. The door band, on the other hand, should not be overtightened to the point where the door hangs freely when the door is closed.

How tight should the ground straps be on my tunnel tent?

When using our tunnel tents, the ground straps assist in maintaining the right height and tension of the poles. When they are properly fitted, there should be no stress on the connections that join the inner and outer tents caused by the poles themselves. Because of the excessive tension created by the ground strap, the poles will be put under unneeded stress, and the inner tent will droop inwards at the sides.

My tent has seen a lot of heavy use, how can I re-treat the fabrics?

In addition to being extremely robust, our textiles are also waterproof and highly water-repellent. Sun, wind, rain, and wear, on the other hand, will deteriorate any cloth with time. More information on how ultraviolet light may degrade textiles can be found here. Re-treating the fabric will increase both the protection against UV damage and the water repellency of the fabric, but it will have no effect on the tear strength of the cloth. Restoring the condition of your outer tent The Nikwax TentGear SolarProof, which is simple to apply and does not contain fluorocarbons, is the product we suggest for re-treating our outer tent materials.

TentGear SolarProof should be sprayed or brushed over the cloth, and any surplus liquid should be wiped away.

Please keep in mind that TentGear SolarProof should not be used on a new tent, but rather on a tent that has lost its water resistant capacity over time.

Restoring the condition of your inner tent Nikwax TX may be used to restore the water repellency of your inner tent after it has been exposed to the elements for an extended length of time.

Spray the TX with the same method as with TentGear SolarProof. Directly after, wipe away any extra liquid and allow it to dry. We encourage you to visit if you would like additional information about these items as well as information on where you can purchase them.

My tent is dirty. How do I clean it?

Setting up your tent and then cleaning it with a sponge and lukewarm water after your journey is a wonderful idea once you return from your adventure. We strongly advise against the use of any cleaning chemicals. Using a tiny brush, thoroughly brush the zippers to ensure that no sand or grit is left in the teeth of the zippers is also essential. Sand in the zippers can wear out the sliders, preventing them from functioning correctly again after they have been cleaned. Check and double-check that your poles and pegs are clean and free of damage before using them.

If the tent is really unclean and dusty, we usually wash it in the washing machine.

No matter how you clean it, be certain that the tent is totally dry before putting it away for the season.

How do I use a line runner?

1. To loosen the Line Runner, use your fingers to draw the line away from the Line Runner’s body, as indicated in the illustration. Pulling the line into the Line Runner’s channel will secure it in place.

My pole broke, what do I do?

One extra pole piece as well as a repair sleeve are included in each pole bag for convenience. In the meanwhile, you may use the repair sleeve to temporarily fix your pole until you get an opportunity to replace the damaged pole segment. To get a PDF with step-by-step instructions on how to repair a tent pole, click here. Making use of a repair sleeve Twelve. Slide the sleeve over the damaged pole and center it over the damaged area, then tape the ends of the sleeve together to secure it in place.

  • Pull the end-stop of the pole out until the knot in the shock cord is visible.
  • 2.
  • Untie the knot and remove the end-stop off the cord to complete the process.
  • Pull the pole apart to reveal the shock cord that is hidden underneath the broken piece of the pole.
  • 4.
  • Keep track of the order so that you can replace them in the proper sequence.
  • 6.
  • Reattach the end-stop to the shock cord with a knot.

My zipper doesn’t work, how do I fix it?

When there is a problem with a zipper, the first clue that anything is wrong is that the zipper will not remain closed when you try to zip it closed. What generally causes this is dirt and grit in the zipper, which wears microscopic grooves on the inside of the zipper slider as a result of the zipper being used. You may make a temporary repair by pinching the edges of the zipper slider together until you have the opportunity to replace it. It is critical to clean your zippers on a regular basis in order to avoid this from happening.

  1. In order to replace the zipper sliders, first open up the stitches at one end of the zipper and then remove the little metal clip that is attached to it.
  2. Remove the old sliders by sliding them off.
  3. Install the new sliders by sliding them on and making sure that they are facing in the same orientations as the previous ones.
  4. Double-check that the sliders are aligned appropriately, not only in the front and rear but also in the top and bottom.
  5. It might be difficult to put the slider on with the flat end first on some occasions.
  6. 6) Once you’ve begun to slide the zipper slider along the zipper, continue to pull on either side of the zipper to complete it.

7, 8. Once the sliders are in place and functioning properly, rejoin the stitches you undid and sew a few stitches to seal the end and prevent the sliders from coming loose again. Reset the metal clip if at all feasible.

How do I attach a line runner?

12. Feed the guy line through the opening on the bottom of the Line Runner, which is triangular in shape. 3. Pull the line through the connection point until it snaps into place. In the same manner as shown, thread the second end of the guy line through the other hole on the top of the Line Runner. 5. Tie the end of the guy line in the manner indicated on the right side of the picture. We propose that you tie your knot using an overhand knot. This completes the installation and makes your Line Runner usable.

How do I attach the Footprint?

The best time to attach your Footprint to your tent is just before you want to go camping. Lay your tent out on the floor with the floor facing up if you’re indoors. The Footprint should be placed directly on top of the tent floor with the logo side facing the floor, and its logo should be aligned as follows:

  • If the Footprint extends into the vestibule, the logo or logos on the Footprint should be aligned with the centre of the main outer tent door or doors if the Footprint covers the vestibule. Keep in mind that the main door on the Kaitum GT and Nallo GT is the large entrance, rather than the small entrance near the front of the extended vestibule
  • If the Footprint does not cover the vestibule, the logo on the Footprint should align with the logo on the inner tent door
  • The Rogen is an exception to this rule due to its asymmetrical design. When the Rogen Footprint logo is displayed, it should be in alignment with the logo that appears on one end of the Rogen outer tent.

Look on the back of the Footprint’s hang tag for specifics about your particular tent model. Once the Footprint is properly oriented, attach the toggles that are located around the circumference of the Footprint to the rings that are located at the bottom border of the outer tent’s bottom edge. When the tent is fully assembled, the reflective side and logo should be facing upward. When you pack up your tent at the end of a trip, you may leave the Footprint still connected. Just make sure that the entire tent, as well as the Footprint, is totally dry before putting it back in its place.

Why do the footprints on the Anjan, Rogen, and Niak tents not cover the vestibule?

The optional Footprints do not cover the vestibules on the Anjan, Rogen, and Niak tents since the outer tents do not extend all the way to the ground on these three models. During heavy rains, water can seep into the vestibule through the space between the outer tent wall and the ground in the vestibule. If the Footprint covered the vestibule area, water may seep below the tent and cause it to collapse.

See also:  Where Do Tent Caterpillars Come From

My tent is paler after a lot of time in the sun, what happened?

In addition to being extremely robust, our textiles are also waterproof and highly water-repellent. Sun, wind, rain, and wear, on the other hand, will deteriorate any cloth with time. A faded or bleached appearance to the fabric indicates that the cloth has begun to be affected by ultraviolet rays. UV rays from direct sunshine have negative effects on our skin, and the same is true for all materials, including tent fabrics (which is terrible). With prolonged exposure to the sun’s radiation, particularly at altitude and in the southern hemisphere, the performance of a cloth can be compromised.

Extended exposure to ultraviolet radiation (UV) weakens the tear strength of any fabric, which is one of the primary reasons we employ materials with high tear strength.

This, on the other hand, does not imply a deterioration in the fabric’s waterproofing properties.

More information on how to withdraw your tent may be found here.

Pitching your tent in the shade with a tarp over it and not keeping it set up during the day while you aren’t using it can help you achieve this. In high UV conditions such as high altitude, glaciers, and deserts, this is especially crucial since the skin can burn easily.

How do I roll my outer tent door?

We recommend rolling the door in a certain manner rather than just bundling it and securing it with the toggle because it works better to keep it out of the way, it is more secure, and it keeps the door and zipper from dragging in the mud, which will extend the lifetime of your tent. To roll the door, begin by rolling the fabric of the door in the direction of the toggle. As you continue, collect the cloth toward the toggle by folding the loose end of the roll in and gathering the fabric. One of the objectives is to bring the main body of the door, including the zipper’s end, beneath the toggle.

Pull out the elastic loop and thread it through the toggle when you have the door fully rolled.

Amazon.com : tent pole shock cord

Ships to NetherlandsThere are only 7 of these items left in stock – purchase soon. There is just 1 left in stock – order soon. Ships to the Netherlands extremely well-liked sponsored | based on the number of customer ratings and the number of stars Ships to the Netherlands are available. Only 7 of these items are left in stock – purchase soon. When you spend $300.00 or more on specified goods, you will save 8%. Only 9 units left in stock – purchase soon. Ships to the Netherlands Ships to NetherlandsThere are only 17 of these items left in stock So purchase soon.

  • There are only 4 left in stock, so act quickly.
  • Only 14 of these items are left in stock – purchase soon.
  • Only 17 of these items are left in stock – purchase soon.
  • Ships to the Netherlands are available.
  • A 5% discount is applied at the time of purchase.
  • Ships to NetherlandsThere are only 15 of these items left in stock So purchase soon.

GOLBERG Elastic Shock Cord – 2.5mm, 1/32, 1/16, 3/16, 5/16, 1/8, 3/8, 5/8, 1/4, 1/2 inch diameter – Various Colors – 10, 25, 50, 100 ft lengths – Made in the USA (Neon Orange, 3/16in x 25ft)

Ships to the Netherlands are available. Only 6 of these items are left in stock – purchase soon. Ships to the Netherlands are available. There is just one left in stock, so act quickly.

Amazon.com: AceCamp 1/8 Inch Shock Cord Pole Repair, Replacement Bungee Strap Rope for Worn & Old Tents, Emergency Stretch Elastic Cord, Moisture UV Weather & Abrasion Resistant, 65 Feet : Tools & Home Improvement

On July 6, 2020, a review was published in the United States. Everything worked as it was intended to. I worked my way through the three poles that needed fresh cable. My first step was to lay out the poles and draw the old cord out a little bit before securing it and cutting the knot. I then used a little piece of scotch tape to attach the new cord to the old one, coiled it up tightly, and pulled the new cord through with the old cord. It took less than 5 minutes each pole to complete the task.

  • Purchase that has been verified Consequently, the poles of my cherished, leaking North Face Assault 2 from 2016 were no longer elastic.
  • I would have preferred it to be a fraction of an inch bigger in diameter, but I’m not going to argue.
  • Although it is a natural instinct, doing so will cause you to be frustrated for hours at a time.
  • Bring the old and new elastic through the poles (mine have seven pieces, so this is a significant undertaking).
  • Most of the time, it’s a pretty calm place to work.
  • Tom Simmons, of Grinnell, Iowa, is a writer.
  • My tent has been brought back to life after being declared dead.

In order to draw the rope through the fiberglass poles, you’ll need a wire to feed it through the poles.

Please keep in mind that the cored should be around 1.5 poles to 2.0 poles shorter (unstretched).

Then feed it through the final two poles and tie a temporary knot at the end.

The document was reviewed in the United States on April 13, 2017.

This elastic is robust yet thin, and it is precisely the same as the elastic that was initially used in tent poles from the manufacturer.

The elastic is robust enough that it may be threaded through the tent poles without the use of any special instruments.

Once the project was completed, there was enough of elastic cord left over to use for other projects in the future.

On May 6, 2021, a review was published in the United States of America.

Because it was shaped like a spider, I was apprehensive about attempting to repair it (definitely did not think I could).

After that, I just watched a few YouTube videos – no problem.

Because of the large number of tent poles, I ended up repairing two whole sets of tent poles.

I’ll never be reluctant about anything again!

Purchase that has been verified I received this thing in a short period of time.

I’m overjoyed that I was able to successfully replace the old shock cable.

On January 1, 2021, the United States will conduct a review.

I had enough to complete both the huge shock poles and the rain fly poles in one go.

The material finish was easy to slide between the tubes.

The quality of the material was superior than some of the latest gear I’ve seen.

Purchase that has been verified Coleman fiberglass poles are a perfect replacement for old Coleman fiberglass poles.

The cord snaps onto one end of the pole portion, causing the knot end to be knocked out of the way. In order to create appropriate tension without overstretching the cord, I drew out roughly a third of its whole length.

Top reviews from other countries

5.0 stars out of 5 for this product It’s a long stretch. The article was reviewed in the United Kingdom on August 15, 2018. Purchase that has been verified It appears to be an appropriate length for the money and appears to be appropriate for the task. 4.0 stars out of 5 for this product Four out of five stars On September 7, 2016, a review was published in the United Kingdom. Purchase that has been verified The ideal back-up. Installation in poles is simple, and the resulting structure is sturdy.

  • On June 26, 2017, a review was conducted in Mexico.
  • You never know when you might need anything and you don’t want to be caught without it.
  • On July 27, 2021, a review was conducted in Germany.
  • I would recommend it highly.
  • Purchase that has been verified The product is good, but the packaging is excessive, and it would have been better if it had been packaged differently.

How to Replace the Shock Cord in Tent Poles ?

If the following instructions from Sierra Designs for changing the shock cable for an SD Dome tent (original) are helpful, please see below: Hello, Elliot. You may absolutely restring them at your convenience: 1). A set of poles, shock cord (which can be purchased at practically any outdoor shop or online), a table vice, two hammers or a hammer and a mallet, forceps or needle nose pliers, and a pair of needle nose pliers are all necessary tools. 2). Determine the sort of tip that will be used on the poles of your model.

  • a).
  • I Position the pole so that the tip end is sticking out of the table vice (position it with cloth or a towel around the pole, and very lightly secure it into place) ii).
  • iii).
  • Some types feature an anchor washer within the last segment of the pole, so if the tip of the pole does not appear to be linked to the cable, don’t be concerned.) b).
  • c).
  • Insert a new line of shock cord immediately back through the holes created by the removal of the tips and the pulling out of the faulty chord.
  • If it was a press-fit, tap the end tip back into place to secure it, just as you did when you removed the cord.
  • With the remaining end open and free of a tip and shock cable dangling from it, clamp the shock cord just where the pole terminates and extend an arm’s length directly away from the pole to create a straight line.
  • If the cable is stretched too far, it will break much more quickly.
  • If you are having difficulty understanding the arms-length description, a yard is a decent measurement to use.

Secure and squeeze the shock cord at the point where the pole terminates with forceps while maintaining that arm’s length of stress on the pole (so that it cannot retract back into the pole) I Remove the remainder of the cord beyond the forceps, but allow enough to make a knot to complete the task at hand.

Tie the remaining anchoring knot to the pole’s tip or to the washer within the pole, depending on which is most convenient (varies on models) iii).

After tying to the tip, when you remove the forceps, the tension should nearly completely reattach the cord and tip to their original positions, although they may need to be screwed or tapped in place. g). Pour yourself a drink.

Stansport Tent Pole Shock Cord Repair Kit #748

The stock number is 748UPC:011319615205. Style:220764 Stock:748Color:Black

  • Description Replace your tent’s shock cords and you’ll be able to extend the life of both your bank account and your tent. NOTICE: This product might induce an allergic reaction by exposing you to chemicals, such as lead, phthalates, or other chemicals that are known to the State of California to cause birth defects or other reproductive damage. More information may be found at: thirty-inch wire for shock cord installation
  • Six washers for fastening the new shock cord
  • And

Specifications Replace your tent’s shock cords and you’ll be able to extend the life of both your bank account and your tent. NOTICE: This product might induce an allergic reaction by exposing you to chemicals, such as lead, phthalates, or other chemicals that are known to the State of California to cause birth defects or other reproductive damage. For further information, please see: of elastic shock cording. Installation of shock cords requires a 30-inch cable. Six washers are required to secure the new shock cord.

NOTICE: This product might induce an allergic reaction by exposing you to chemicals, such as lead, phthalates, or other chemicals that are known to the State of California to cause birth defects or other reproductive damage.

Installation of shock cords requires a 30-inch cable.

Replace your tent’s shock cords to ensure that both your financial account and tent last as long as possible.

To learn more about elastic shock cording, see the following website: Shock cord installation requires a 30-inch cable.

Leave a Comment

Your email address will not be published. Required fields are marked *