How To Cut Fiberglass Tent Pole

Quick Answer: How To Cut Fiberglass Tent Pole

What is the best method for cutting fiberglass tent poles? Without a doubt, a basic hacksaw. If you don’t already have one, you’ll soon realize that you’ll need one. Masking tape a few loops around the area you wish to cut, then do it outside. It will take around three minutes total.

Can you shorten tent poles?

Simply cut the cord; cutting the cord one inch shorter is OK. Making a new knot with only the small-diameter part of the pole allows you to attach the last segment of pole to it. (Optional)

How do you cut a fiberglass pole?

Align the rear edge of the fine-toothed hacksaw blade with the pencil mark using a straightedge and a level. Allowing the hacksaw to slowly move toward you and then away from you will allow you to cut through the fiberglass stick. Cutting should be continued until the fiberglass stick is divided into two halves. To finish the cutting operation, remove the masking tape off the fiberglass stick and discard it.

How do you straighten a leaning pole?

One person holds the pole in place so that it does not move while another digs down the side of the pole and away from the lean. Using two to four lengths of rope approximately 5 feet long, attach each end of the rope to the pole at a height of about 3 feet above the ground. With the assistance of a buddy, straighten the pole.

How do you straighten a bent trekking pole?

To wrinkle a bend that hasn’t already been creased, grasp the pole by the handle and hit it more or less lightly at the outside point of the curve on a tree or wooden post. Continue in a rhythmic manner until it is straight. Slowly and slowly, please. If they are crumpled, you are in trouble.

What cuts fiberglass rods?

In case you decide to cut our fiberglass by hand, here are a few pointers to remember: When working with modest quantities of material, a fine-toothed hacksaw will suffice. When cutting through fiberglass, make sure to hold the rear side of the tube or rod to prevent splintering of the fiberglass as the blade passes through the back.

How do you fix a bent aluminum tent pole?

A tube straightener, a rubber mallet, or the Mighty Mite Bender are all tools that may be used to straighten a twisted tent pole. In order to keep costs down, you might consider using the sand-filling technique, which will allow you to undo the bend in the pole without breaking it.

What material is best for tent poles?

Tent poles and other tent-related items Tent poles made of fiberglass. One of the most commonly used pole materials since they perform admirably and are one of the most affordable alternatives available for poles. Tent poles made of aluminum. In terms of strength to weight ratio, aluminum poles are extremely strong and not easily broken. Tent poles made of carbon fiber. Tent poles made of steel. There will be no poles or pole substitutes.

What is better aluminum or fiberglass tent poles?

If you want to purchase large tents, such as an 8-person tent or a 6-person tent, aluminum tent poles are the ideal material to use. In comparison to fiberglass tent poles, they are significantly more durable and capable of supporting huge and heavy canvas or tent structures without sagging or breaking.

Are Aluminium tent poles better than Fibreglass?

The durability of aluminum pole tents can be attested to by campers who have used them, as they do not break easily.

Aluminum tent poles are a popular choice among campers because of the ease with which they can be fixed when they become bent. However, they are far lighter in weight than fibreglass, pure steel, and wooden tent poles, yet being quite sturdy.

Can you cut an umbrella pole?

Aluminium-pole tents are extremely durable and do not break easily, as campers who have tried them can confirm. Aluminum tent poles are a popular choice for most campers because of the ease with which they can be mended when they become twisted. In comparison to fibreglass, pure steel, and hardwood tent poles they are far lighter while being extremely sturdy.

How do you cut fiberglass without splinters?

Place masking tape along the cut line of a panel, mark the line on the tape using a pencil, then saw through the tape to reduce chipping and splintering. Inside corners cut in a panel should be rounded to prevent a fracture in the completed item as a result of a sharp corner.

What is a tent ferrule?

These aluminum ferrules are lightweight and robust, and they are the ideal technique of joining two short rods or tubes together to form a longer pole or telescoping rod. Among the numerous applications include, but are not limited to: Ferrule for Tent Poles Tube or rod repair is a simple process. It is simple to sleeve into fabric once it has been built since the edges have been de-burred.

What are flexible tent poles made from?

Tent Poles Made of Glass Fiber Because of the inexpensive cost of glass fiber, it is a common choice for less budget tents due to its durability. Because of its flexibility, a tent bends with the wind rather than standing hard against it, allowing it to shed gusts. When you are experiencing something for the first time, it might be a little unnerving.

What does tent pole mean?

As used in broadcast and motion picture programming and films, the term “tent-pole” refers to a program or film that is important to the financial success of a film studio or a television network. It is intended to be an analogue for the way a strong center pole offers a secure framework to a tent construction.

How do you clean cut fiberglass?

The Most Effective Techniques for Cutting Fiberglass Panels Router. If you decide to use a router to cut your panels, make sure to choose a blade with a fine edge so that the edges are clean and smooth when you are finished. Fiberglass Trimmer with a lot of power. A trimmer is a lightweight and strong tool that can readily cut through durable fiberglass, such as that used in paneling, without damaging it. Jigsaw. A circular saw is a saw that goes around in a circle. Hacksaw.

Can aluminum be bent back?

The malleability of aluminum makes it a convenient material to deal with, but also makes it susceptible to unintentional bending. You may simply straighten aluminum by yourself rather than having to purchase a new piece of metal if you have the correct equipment.

How do you remove a ferrule from a tent pole?

Place the pole in a vice and heat the ferrule’s tip with a heat gun, grabbing the ferrule with pliers as it heats up, and turning it to check if it starts to move. It is important not to overheat the pole since this will cause it to burn.

Replace and Repair Tent Poles

The majority of modern tents are constructed of glass fiber poles with elastic flowing through the center. If you don’t tighten your guide ropes enough to prevent your tent from shifting about, you may find that these poles split through the middle.

Most tent retailers, such as go outside, retain used ones in store from previous show tents; if you ask respectfully, they may be willing to offer you a few of them for free if your tents are less than a year old and you purchased them from them.

Step 1: You Will Need.

Hacksaw and sandpaper for replacing the poles In the shape of a large needle Fishing line with a lot of strength Pen with a marking pen Mask for the face

Step 2: Getting Started

Remove the poles from the elastic by cutting the knot at one end of the elastic and removing the poles from the elastic.

Step 3: Cutting to Length.

Mark the length of the old pole adjacent to the new pole to use as a reference. Hold the new pole firmly in your hands and carefully cut the pole to the desired length, being careful not to damage the fibers. WHEN WORKING WITH FIBERGLASS, ALWAYS WEAR A MASK.

Step 4: Sanding

Using slow, gentle sanding, remove any splinters from the top of the pole, then sand the edges to a cone shape until they are smooth. Check that the poles are snugly fitting into each other by putting them through their paces. WHEN WORKING WITH FIBERGLASS, ALWAYS WEAR A MASK.

Step 5: Threading the Elastic

Using fishing line to thread the elastic knot, thread one end of the elastic through a knot-free fishing line end, and then tie a needle on one end of the fishing line to the knot-free end, you will need approximately twice as much fishing line as the pole length. Make sure the knot is small enough to fit inside the pole freely. Embroider the pole by inserting the needle and thread inside it and gently tapping it on the floor until the needle is at its lowest point, then gently pulling the elastic through.

Step 6: Last Pole

Holding the elastic around your finger and tying a double knot at the end of the fishing line will help you draw the last two poles tight. Once you have finished, cut the fishing line and you are finished!

1 Person Made This Project!

You are currently browsing theTips and Dealsforum section of our website. What is the best way to cut fiberglass tent poles? Date: September 12, 2008, at 12:12 a.m. (PST). I have a tent that has a fractured pole, but the remainder of the tent is in good condition otherwise. I bought some generic replacement poles, which are the perfect diameter but are a little too long for my application. Is there a dremel action? What is the best method for cutting fiberglass tent poles? The date is September 12, 2008, at 1:22 a.m.

  • The date is September 12, 2008, at 1:22 a.m.
  • Simply wrapping some tape over the side you wish to maintain before cutting should prevent the fabric from fraying.
  • The date is September 12, 2008, at 1:27 a.m.
  • As a result, splintering is kept to a minimum.
  • Those look like nice options, however if it’s a hollow pole, you might try inserting a solid object item in the weak location and gluing it in place?
  • That’s something I tried a few years back and it worked for me!
  • It would be beneficial to use a miter box to ensure that the cut is straight.

Take precautions to keep yourself safe from the dust.

To re-bond the fibers, coat the cut end with super glue after it has been cut, then sand off any sharp edges and re-apply the super glue.

On September 12, 2008, at 11:36 a.m., I asked for advice on cutting fiberglass tent poles.

See also:  What Size Fan For 3X3 Grow Tent

It is sometimes necessary to accept the situation as it is.

Date: September 12, 2008 @ 12:53 p.m.

It’s a pipecutter, really.

And then you’ll have one on hand in case of a plumbing disaster.

Depending on whether the pipe is hollow tube or solid rod, the pipecutter may or may not be effective.

It shouldn’t be too challenging.

It would be preferable to use a Dremel-like equipment (with high RPMs) with a fine ceramic or diamond blade.

It is the 12th of September, 2008, at 4:27 p.m.

I’m not a terrible man in the least!

So why should I have to spend half of my Sunday listening to people tell me that I’m going to Hell?

What is the best method for cutting fiberglass tent poles?

(Eastern Standard Time) Without a doubt, a basic hacksaw.

Masking tape a few loops around the area you wish to cut, then do it outside.

Dust should be treated as if it were broken glass.

There were 132 people in attendance.

On October 3, 2020, the number of guests reached a new high of 5122.

Get in Touch With Us Using MacResource.com and participating in the Forums is subject to the Terms of Service (TOS).

Please review our Terms of Service. MacResource.com is a trademark of MacResource.com, which is owned by MacResource.com. All other intellectual property rights are the property of their respective owners.

Fibreglass Tent Pole Repair guide

How to inspect and repair damaged Fibreglass pole-work on contemporary tents and lightweight awnings is the subject of this article. Since of this, even if you do not believe you have broken portions, it is a good idea to examine your poles at the start of each season because fractures can occur that are difficult to detect. It’s preferable to learn about them before you go than to have your tent pole come apart when you’re trying to put up your tent.

Recommended Kit

  • Sandpaper (180g to 200g is excellent)
  • Tape measure
  • Replacement fibreglass pieces
  • Replacement shockcord (elastic)
  • Electrical tape or permanent marker
  • A junior hacksaw.

A excellent suggestion, but not needed, is to use latex or rubber gloves and to use a vernier calliper if you have one.

TermsJargon

What we are referring to when we state various things in this piece.

  • Pole Piece – A single fibreglass section that is normally capped with a metal sleeve at one or both ends, depending on the design. Tent pole made up of many fibreglass parts with a length of elastic running in the centre is known as a full pole. A ferrule is a metal sleeve that is attached to the end of a fiberglass pole segment. shockcord – the elastic “string” that goes through a full pole and connects the individual pole components
  • Spiggot – A metal fitting that is attached to the end of some tent poles to allow them to be threaded through an eyelet. An alternative to the more widely used ring and pin arrangement.

Performing a visual inspection for damage One by one, inspect and mark every broken area as you come across it so that you know where you are in the process of repairing the pole. Put a flashlight in front of the bundle of poles and inspect down the ends for fractures or other damage. Even though the fractures are slight and difficult to detect, they will shatter the next time you bend the pole to fit the tent’s pole. Don’t forget to move the thread aside so that you can inspect each portion thoroughly.

  1. After that, lay out the pole and join it together as if you were putting up a tent for the first time.
  2. It is possible that it will snap when you are attempting to put your tent up, making it extremely difficult to thread the pole through the tent sleeve.
  3. Sectioning off new parts Typically, each individual part of a fiberglass tent pole is made out of a fibreglass rod that has been fitted with a metal sleeve at one or both ends.
  4. Complete one pole at a time, cutting portions and fitting them together before going on to the next.
  5. Depending on the length of your new fibreglass pieces, they may or may not include a metal sheath that matches your originals.
  • Place the new and old pieces next to each other and make sure the ends of the metal sleeves are the same length. When cutting portions from the end of the pole – Then trim to the same overall length as before. The new and old parts should be placed next to each other and the little dimples in the metal sleeve should be aligned while cutting mid-sections off the pole. After that, cut. It is important to ensure that the overall length of the fibreglass remains constant.

Gloves should be used when cutting fibreglass to prevent splinters and dust from entering into your skin and being embedded in the material. Always cut towards the center of the part when cutting it to length to avoid splintering the edge while cutting through it. Cut a section of the pole halfway through, then flip it and cut another section halfway through. Continue until you’ve sliced all the way through. Adding the additional pieces to the existing structure Install all of the replacement parts for one pole when you’ve finished cutting them for that pole before going on to the next pole.

  1. Before removing the pole from the ground, count the sections and measure the total length, making a note of both so that you can ensure that the repaired pole is the correct length before putting the pole away.
  2. In some cases, just pushing the knot out from the other end of the section would enough; in other cases, pulling it out using needle tip pliers or a wire rod inserted through the pole may suffice.
  3. Removing all pieces of the shockcord when replacing it because it is frayed is recommended.
  4. In the event that you have an end portion with two metal sleeves, thread this section first, as this will make it easier to thread all of the other sections when it has been completed.
  5. Pull a bit harder to increase the tension in the elastic.
  6. Cut off any surplus shockcord after tying a knot at the end of the shockcord.
  7. For each whole pole with damaged pieces, repeat the aforementioned processes for cutting and fitting for a total of three times more.

If you’re purchasing from a store, remember to bring your old pole-work with you.

If you’re purchasing online, you’ll need to take your own measurements for the sizes.

A vernier calliper can be used to determine the diameter required, or a tape measure can be used if one does not have access to one.

Then take another section of your pole and repeat the process with the tape measure.

Attempting to measure the diameter of the pole by holding the tape up to it is virtually hard to achieve with any accuracy.

The sizes that are often used on tents include 7.9mm, 8.5mm, 9.5mm, 11.2mm, and 12.7mm in diameter.

Check your tape measure; the least number of millimeters you can see will be the size that is one size larger than what you want (e.g.

Replacement parts are not available for the extremely tiny sizes of pole less than 7.9mm in diameter.

Some bigger tents may employ poles with a diameter of 16mm on occasion.

Camping World has a fully equipped workshop where we can do fibreglass and alloy pole repairs on your behalf.

For those of you who would prefer that us handle the repair, you can either drop off the pole at our shop or arrange a repair through our website on our pole repair page. There are no goods available in this category at this time.

How to Cut a Fiberglass Stick

To avoid getting splinters and dust into your skin while cutting fibreglass, it is recommended that you use gloves. Whenever you are cutting the part to length, cut towards the center to avoid splintering the edge as you are cutting through it. Then turn it over and cut a portion of the way through the pole. It is necessary to repeat this process until you have sliced through completely. The new parts are being fitted in. Install all of the replacement parts for one pole after you’ve completed cutting them all for that pole before moving on to the next.

  • Before removing the pole from the ground, count the sections and measure the total length, making a note of both so that you can ensure that the repaired pole is the correct length before storing it away for safe keeping.
  • Otherwise, pull the knot out using needle nose pliers or a wire rod through the pole if you can’t get it out by pushing it out from the other end of the section.
  • Replace just the pieces that are frayed if the shockcord has to be replaced.
  • If you have an end part with two metal sleeves, thread this portion first since it will make it easier to thread all of the other sections after it has been threaded through.
  • Pull a bit harder to apply some strain to the elastic.
  • Cut off any surplus shockcord after tying a knot on the end of the shockcord.
  • Then, for each full pole you have with damaged pieces, repeat the preceding processes for cutting and fitting it.

It is necessary to determine the length and diameter of new pole pieces before purchasing them for tent pole repair.

What size you require should be able to be determined by the personnel on hand.

Sections with the proper diameter but which are too lengthy must be obtained and then chopped to the proper length.

Take a part of your pole and place it end down on a tape measure or a ruler on a table.

After that, find out how big it is in diameter.

Make sure you’re measuring the fibreglass tube itself, rather than its diameter inside the metal sleeve.

Very small poles are occasionally available in sizes smaller than this, but no sizes in between are available.

if you can see 9mm, but not 8mm – your pole will be 8.5mm diameter).

All of these items will need to be bought from the tent maker.

Although they are extremely rare, we may sometimes supply them if you contact us in advance.

For those of you who would prefer that us handle the repair, you can either drop off the pole at our shop or schedule a repair through our website on our pole repair page. The goods listed in this category are not currently available for purchase.

Items you will need

  • Work table, safety glasses, a hacksaw with a fine-toothed cutting blade, tape measure, masking tape, pencil, and a pair of safety glasses
See also:  How To Attach Lovevery Tent

Pulling the tape measure along the fiberglass stick will give you an idea of how long it is. Remove the tape measure by placing one thumb at the dimension you need to cut the fiberglass stick and releasing it. Masking tape should be wrapped around the fiberglass stick. Remove anything from the region that is at least 1 inch on either side of the location you will be cutting. Stretch the tape measure along the fiberglass stick and make a pencil mark on top of the masking tape at the length you want to cut with the pencil to indicate where to cut.

Put your safety glasses on first.

Align the rear edge of the fine-toothed hacksaw blade with the pencil mark using a straightedge and a level.

Cutting should be continued until the fiberglass stick is divided into two halves.

How do I repair fibreglass poles ?

Your pole is made up of pieces and an elastic shockcord for added flexibility. The cord is simply tied at each end once it has been threaded through each piece. 1. Take measurements of the portion or sections that will be replaced (the new section will need to be cut to length). Measure the length of the new portion and cut it to that length. We propose that you use a tiny hacksaw for this task. Once the end has been cut, it should be filed or sandpapered smooth. When cutting a new fibreglass pole, start at one end and cut halfway through before turning the pole around and finishing the cut from the other end.

  • 2.
  • The pieces should be removed one by one until you reach the portion that needs to be replaced (it is critical that the sections are reassembled in the same sequence as they were removed when the pole was dismantled).
  • Insert the new part or sections into the existing ones, then re-thread the cord through the sections and tie a knot at one end.
  • Alternatively, tent poles and other replacement components may be obtained directly at www.campingparts.co.uk.
  • Send input if you agree or disagree.

How To Repair Broken Fiberglass Tent Pole

Do you have a tent at home with a damaged fiberglass pole? If so, let us know. Did your tent pole break while you were camping? What is the best way to repair split fiberglass tent poles? The likelihood of your camping equipment becoming damaged increases dramatically when you camp on a frequent basis. Accidents happen all the time, and your poles may become damaged as a result.

This might be really unpleasant since you will be unable to utilize your tent and enjoy the outdoors as a result. In this regard, I will provide you with some practical tips on how to repair a fiberglass tent pole so that you can get back to camping in no time.

Fix a broken fiberglass tent pole like an expert

When the fiberglass poles of a tent are damaged, the majority of people believe that their camping days are over and that they will have to purchase a new structure. They are unsure of how to deal with the repairs to the damaged poles. Because of a broken tent pole, they decide to discard their existing tents and consider purchasing new ones. Are you having the same thoughts? You are under no obligation to take such drastic measures. You will be able to repair your tent if you have a little bit of training and the appropriate equipment.

Fiberglass tent pole kit

Among the items you will require for this project are: replacement tent poles, a tiny hacksaw, and a screwdriver. SandpaperØ A face mask made of duct tape

The process

The fiberglass poles that are used to support tents are often constructed from a number of loose pole parts that are kept together by a flexible cable or rope. The elastic cable, also known as a shock cord, is threaded through the length of the poles and knotted at both ends to keep it in place. In the event that your pole breaks, it is most probable that just one of the portions has been broken off. You will need to replace it if you want to restore the tent to its original state of operation.

  1. Measure the precise portion of the tent pole that has to be replaced and mark it on the tent pole.
  2. Cutting the fiberglass pole with a hacksaw will require you to put on a face mask, which you should do before starting.
  3. Use duct tape to hold the new pole in place while you cut it to the proper length.
  4. The creation of splinters will be prevented as a result of your ability to cut in an ordered manner.
  • Eliminate any remaining pieces of Duct Tape from the pole and sand the pole’s edges to create an even surface. Place the entire tent pole on the floor and begin untying the knot at the end of the pole that is closest to the portion that will be replaced. It is doubtful that you will be able to reach the end of the knot with your fingers, thus a needle nose plier should be used to free it from the pole. It’s possible that the knot was knotted too tightly and you’ll have to cut it
  • Holding the shock cord in place, gently remove the pole parts until you reach the broken part that has to be repaired or replaced. Removing the damaged portion and replacing it with the section that you have prepared is a good idea. While maintaining your grip on the shock cord, re-stretch it through the pole portions that you had previously removed for the time being. Due to the fact that the parts are of varied lengths and diameters, it is important to return the poles in the same condition as you found them. It is possible that your tent will not stand up properly if you mix them together. Finish the string by tying a knot at the end and making sure that it is taught in the same way that you discovered it. The cable secures the tent’s poles in place and provides a defined framework for the tent. This is why you should make certain that it is taught in sufficient quantities.

If you realize that this is not the case later on when you are setting up the tent, take the end of the shock cord and modify the knot accordingly. From either end of the poles, you may do this action.

Use a tent pole repair sleeve

Another option for resolving the issue is to use a pole repair sleeve to secure the pole. A short pole or a so-called splint, which is typically included with the tent that you purchase, is used to repair the tent in the shortest amount of time possible. You should get it even if it is not included in the bundle to be prepared for the worst case scenario. So, what is the best way to fix a tent pole with a splint? To begin, arrange the two broken pole portions in a straight line. If the pole is not broken, simply bend it in half and gently straighten it out.

Place the splint over the pole so that it completely covers the problem. Straightening the bent parts using pliers can be done with the assistance of a friend. Wrap duct tape or other heavy-duty tape around each end of the pole multiple times, and you’re done.

Use a tent stake

There is another solution if you don’t happen to have an emergency repair kit or a pole repair sleeve with you. If your pole breaks, you can use a stake to put the two fractured sections of the pole back together again. To begin, arrange the broken pole components in a straight line. If each is bent straight, it may be manipulated using pliers. Assemble the stake and place it next to the shattered section; the stake must be centered between the two fractured components. The next step is to use duct tape or another type of heavy-duty tape to secure all of the pieces in place before proceeding.

How do you replace a shock cord?

Is your shock cable in the poles damaged or no longer stretches when you pull on it? In these instances, it is past time to replace it.

Step1

First and foremost, you must understand how the shock cord is linked. To see the cable, open the end of the pole and pull it out. In most situations, a metal or plastic tab will be located on the pole, which you may pull out and repair the cable with.

Step2

Mark the pole parts with numbers so that you will know how to link them together at the conclusion of the project. Remove the old shock cord by untying it, pulling it out, and placing it somewhere where you can cut a new cord of the same length.

Step3

Take the new cord and connect a tab to the end of it using a piece of tape. You’re almost through with threading the cable through the pole. Using the clamp or vise grip, forcefully pull the cable to cut it off when you reach the end of the final pole segment you are threading.

Step4

Finalize the procedure by connecting the core to the pole’s tip and knot the remaining end of the pole.

Save the money

Tent poles break all of the time, but this does not imply that you must discard your tent and purchase a new one in order to fix the problem. A damaged pole can be repaired by the homeowner. You will be able to fix a damaged fiberglass tent pole without much difficulty if you follow my recommendations.

About The Author

Camping Valley was started by myself. I am the company’s founder. The site is an extension of my outdoor lifestyle and appreciation for the great outdoors that I have. Everything that I learn, experience, and consider worthwhile is available to you on this website. We live in a technologically advanced age, yet nature is always telling us that we should spend time in areas where our hearts and souls feel at home.

Amazon.com : Coghlan’s Fiberglass Tent Pole Repair Kit : Sports & Outdoors

Verified PurchaseReviewed in the United States on August 10, 2019Verified Purchase I bought tent poles of the same diameter as my previous ones, but the ones that arrived were somewhat smaller in diameter, resulting in a gap between the old pole and the new pole when I linked the two together. I was able to utilize metallic plumbers tape to make the smaller pole more tight and fit appropriately by wrapping it in the tape. The threading wire is completely ineffective; instead, simply take out as much of the shock cord as you can and then use a clamp to hold it taught, and you will be able to thread through with no issue.

  • These are inexpensive because they are inexpensive.
  • a rating of 2.0 out of 5 stars They’re priced so low for a purpose.
  • I bought tent poles of the same diameter as my previous ones, but the ones that arrived were somewhat smaller in diameter, resulting in a gap between the old pole and the new pole when I linked the two together.
  • The threading wire is completely ineffective; instead, simply take out as much of the shock cord as you can and then use a clamp to hold it taught, and you will be able to thread through with no issue.
  • These are inexpensive because they are inexpensive.
  • The photographs in this review On December 24, 2020, the United States will conduct a review.
  • Just make sure you don’t inhale any dust.
See also:  How To Stay Cool While Tent Camping

To get the cable into the hole, I had to use a flashlight, which I clenched between my teeth (a headlamp would have been a better idea).

Because the provided wire is fairly thick, you won’t be able to perform the usual thing and attach the end of the cord to the wire; instead, you’ll have to just stuff the wire through with the cord to complete the installation.

In addition, the cable is visible.

A thicker material will not bend as readily, but it will last longer; a blind is often kept in one place for weeks or months at a time, and the weight of rain or snow might cause the rods to break, so a durable material is recommended.

Useless.

Use caution with a hacksaw, as previously suggested, and you should have no problems with splitting or fibers becoming trapped in your fingers.

Purchase that has been verified At the same time, both packs of these Coghlans fiberglass poles display exposed fiberglass, in contrast to the Coleman poles (which are slightly more costly).

Your fingertips will become coated with fiberglass.

They are most likely going to be OK.

Sheesh.

The review will take place in the United States on July 13, 2021.

This was hastened by a recent camping trip where we were pounded by a sudden storm that dumped 4-5 inches of rain in an hour and left us with a collapsed tent with another 6 inches of water in the bottoms.” Putting this pole together and getting it ready to use takes literally minutes and minutes.

  • It was my error, not the pole’s, that caused the problem.
  • As others have pointed out, if you are replacing existing but damaged poles, you will need to trim these rods to size.
  • If you have REI poles that have the pole ends that go into a grommet on the ground, you will also need a drill bit to remove the knot that is holding the internal bungee rope in place on the pole ends.
  • On December 9, 2021, a review will be conducted in the United States.
  • This was a complete success.
  • However, I discovered that the extra fiberglass pole sections are abnormally lengthy.
  • Before purchase, be sure you measure the length of your tent pole sections.
  • Purchase that has been verified Although I cannot comment on how simple it was to install these poles because my husband performed all of the work, our tent pole is now functional again!

However, a little piece of electrical tape fixed the problem. On July 7, 2021, a review was published in the United States of America. There are no directions, but it is quite simple to figure out what to do. However, there should be some sort of set of instructions.

Top reviews from other countries

5.0 stars out of 5 for this product It worked perfectly for mending my Coleman tent poles. On June 24, 2020, a reviewer in Canada noted that the purchase had been verified. In order to repair three broken pole parts on my Coleman tent, I bought these. Although I anticipated they would be too long based on another reviewer’s description, I was able to cut a few inches off the end and then sand it down to perfection, and they functioned flawlessly. The most difficult element was probably getting the elastic chord re-strung through the older pieces of the current tent pole, which proved to be the most difficult.

  • Very good value, excellent protection for my tent, and I’m confident that they will survive for many years.
  • The varillas are made of glass fiber.
  • Purchase that has been verified These varillas were purchased with the intention of replacing a rotted varilla from a toldo with mosquitoes that I had purchased in the United States.
  • I didn’t have to use any elástico or varilla terminations; instead, I simply had to cut a 10 cm strip from the new varilla and cut away the elástico with some nail pins, then use a hilo and an aguja to reinstall the varillas.
  • Purchased on September 29, 2019 in Canada and reviewed on September 30, 2019Verified Purchase “It’s a touch short,” the wife commented on the shortness.
  • It is difficult to locate precise replacement entire poles.
  • Purchase that has been verified I have a Coleman BP Bristol tent that I use for camping.

We were unable to locate replacement poles.

You need delete the previous part.

Then you manage to either re-insert the old shock cord or use a new shock cord to fix the problem.

You have rescued an entire tent for only a few dollars.

On October 26, 2021, a review will be conducted in Canada.

I believe the wire is intended to be used for threading the bungy through the rods, but simply threading it through the rods works just as well. Metal end caps may be used as tent poles, whilst plastic end caps are simply that.

How To Fix Broken Fibreglass Tent Poles

Obviously, this isn’t the best news, but it doesn’t mean you have to cancel your camping trip just yet. Furthermore, you will not be required to purchase a new tent. Replacement tent poles and a little know-how are all you’ll need to restore your tent poles to like-new condition. Continue reading for a fast and simple advice on how to repair broken fiberglass tent poles.

  • A set of replacement fiberglass tent poles for use with a canopy. If you’re not sure what you’re looking for, go with universal tent poles. A little hacksaw, sandpaper, and duct tape are all needed.

In order to construct your pole, you will need to use numerous loose “pieces” and an elasticated cord (sometimes referred to as a shock cord). The shock cord is simply knotted at each end once it has been threaded through each component from one end to the other. Measure the length of the portion that will be replaced (the new section is generally extra-long, so you may need to cure the new pole down to suit). Making use of a tiny hacksaw, cut the new section (if necessary) to the length of the pole that will be replacing the old one.

Then carefully peel away the duct tape and sand the edges until they are smooth.

Retain hold of the shock cord and carefully remove the pieces one at a time (while maintaining them in the proper sequence) until you reach the section that needs to be repaired or replaced.

You may always shorten or lengthen the shock cord by fishing out the knot in one of the end poles as it becomes necessary.

DON’T FORGET TO CHECK OUT OUR FULL CAMPING EQUIPMENT RANGE.

Have you purchased a tent pole repair kit but aren’t sure how to put it together? Take a look at the easy step-by-step tutorial provided below.

  1. After cutting the old elastic in the original tent pole and pulling out the damaged tent pole piece, you may finish the job. It may be difficult to pull the end of the elastic out of the pole
  2. A corkscrew comes in helpful for this since you can put it into the end of the pole and twist it to capture the knot at the end of the elastic
  3. Make a measurement of the new replacement part to obtain the needed length, and then cut the new tent pole section to size so that it matches the length of the damaged portion
  4. Take into consideration the ferrels at the end of the pole section, especially if it is the end piece and you need to add a second one to the other end. Tighten one end of the shock cord with a granny knot, then sit down and thread the new elastic through the tent pole components, making sure that the sections are replaced in the right order to match the original pole. Tie a double granny knot at the end of each part once it has been threaded through all of the pole pieces
  5. Tip: Threading through from the end without the ferrel (the element that connects two pole pieces) is considerably easier than threading through the middle. Inspect and cut away any extra cord to ensure that the elastic is not excessively tight or too loose.

How to Replace a Broken Tent Pole

Q. Hey, there, Gear Guy! My two-man tent was being set up for air drying when one of the fiberglass poles snapped as I was putting it up. Are there any sites where I may go to acquire a replacement for my watch? — Half-a-pole Adam from Spokane, Washington. Greetings, Mr. Half. First and foremost, congratulations for thoroughly drying out your tent (cue applause). Taking good care of your equipment is essential if you want it to endure for a long period. After that, I’d like to share a few of recommendations that are special to tent poles: The middle of the foldable tent poles should always be the starting point for assembling or disassembling them.

This will place an excessive amount of strain on the elastic within the pole, which may cause it to break.

In addition, such debris might get trapped inside the pole joints and cause issues.

Your best bet is to get in touch with the company who made your tent in the first place.

If it doesn’t work, try returning to the store where you purchased the tent.

In the event that you do get in contact, please careful to specify which specific tent type you have and which pole is damaged.

It appears that replacement poles may be purchased for as little as $5 to $35 for fiberglass poles, depending on the diameter and length of the pole you want, of course.

Aluminum poles are almost twice as costly as steel poles. While I can’t personally speak for the firm, it appears as though they would be able to assist you.

Leave a Comment

Your email address will not be published. Required fields are marked *