What Is Pu Coating On A Tent

What Is Pu Coating On A Tent

Almost all tents, backpacks, and rain gear have a polyurethane (PU) coating added to the interior fabric in order to make the cloth water resistant. With time, this coating may begin to wear away, leaving the cloth with a sticky or gummy texture. There have also been reports of terrible odors emanating from the breakdown of polyurethane that have been compared to vomit or pee.

Is PU coating waterproof?

The interior fabric of most tents, backpacks, and rain gear has a polyurethane (PU) coating put to it to make it water resistant. This coating may wear away over time, leaving the cloth feeling sticky or gummy to the touch. There have also been reports of bad odors associated with the degradation of polyurethane, which have been compared to vomit and urine.

What is PU coating?

Generally speaking, a polyurethane coating is a polyurethane layer that is placed to the surface of a substrate with the intention of protecting it. Various sorts of flaws such as corrosion, weathering, abrasion, and other degrading processes are prevented by applying these coatings to the surface of the substrate.

Is urethane toxic to humans?

Urethane is a CARCINOGEN in humans and is classified as such by the Environmental Protection Agency. There is evidence that it causes malignancies of the lungs, liver, blood, and other organs in laboratory animals. a carcinogen is a substance that causes cancer.

Why does my tent feel sticky?

Moisture, heat, or any combination of these factors might be causing the problem. Before you wipe off the polyurethane coating and reapply it, you’ll want to check your tent to make sure there aren’t any holes or other concerns (which is unlikely considering that it has been sitting unused for a while).

Is 4000 mm waterproof good?

If a cloth has a water column of 1,500 mm or greater, it is termed waterproof. According to Gallen, for a fabric to be called waterproof, it must have a water column of at least 4,000 mm.

What does PU mean in clothing?

PU (Poly) Synthetic Leather is a man-made material that has the appearance and feel of genuine leather, but is not the same substance. This PU material is far less durable, significantly less expensive, and may not last as long if it is used frequently.

Is PU coating safe?

When it comes to leather, PU (Poly) Synthetic Leather is a man-made substance that has the appearance and feel of genuine leather but is not. Although less durable and less expensive than other PU materials, this one is likely to wear out sooner rather than later if it is used on a regular basis.

How long will Polyurethane smell last?

Within 5-7 days of applying polyurethane to your wood floors, you should notice a significant reduction in the scent. However, there may be lingering odors in your home for up to a month after the incident. This process may be accelerated by airing out your home with fans and open windows, as well as by keeping your home warmer than usual.

How PU coating is done?

Polyurethane coating films are created as a result of the evaporation of the solvent followed by chemical interactions between the polyurethane resin and curing chemicals (curing agents).

Water and polyols are two of the most often used curing agents for polyurethane coatings. Moisture-cured polyurethane coatings are polyurethane coatings that cure as a result of an interaction between water and the coating.

Is polyurethane highly flammable?

As a result of its low thermal inertia and thus increased flammability, polyurethane is widely employed in a variety of applications, the two most important of which being soft furnishings and insulation. Additionally, polyurethanes are flammable and produce harmful byproducts such as carbon monoxide, hydrogen cyanide, and other poisonous gases during breakdown and burning.

What happens if you eat polyurethane?

There are just a few case reports of polyurethane foam intake in people who are not suffering from kidney disease. As in our patient’s case, the presenting symptoms were stomach discomfort, constipation, and intestinal blockage due to the development of bezoars. There have been no recorded cases in renal patients, nor has there been any evidence of a link between the condition and fluid retention.

Is Polyurethane harmful to pets?

THE IMPACT OF TOXICITY Polyurethane foam and adhesives have the potential to expand in the stomach, causing an obstruction. In most cases, skin or hair contact results in relatively minor irritation and inflammation of the skin or fur.

What is polyurethane hardener?

When it comes to high performance anti-corrosion protection systems, polyurethane is a two component coating that is often utilized. It is customary for the two components to be a polyacrylic resin and a polyisocyanate hardener. So unpigmented polyurethane resin with hardener:base ratios of 0.75:1, 1:1, and 1.5:1 were applied to mild steel panels, with the hardener:base ratio being 0.75:1.

What is a pu rating?

Tent fabric ratings – The vast majority of tents are constructed of polyester fabric, which is not waterproof in nature. The coating(s) used to achieve ‘waterproofness’ are made of polyurethane (polyurethane). The hydrostatic head is a measurement of how waterproof a cloth is, and it is measured in millimeters (mm), with typical ranges ranging from 800mm to 10,000mm in diameter.

Is PU coating harmful?

It is well-known that polyurethane, a petrochemical resin containing isocyanates, is a respiratory irritant. Polyurethane that has not been properly cured might cause respiratory difficulties such as asthma. Individuals with respiratory disorders, such as children, are particularly vulnerable to the harmful compounds included in polyurethane.

Is 3000mm waterproof enough?

A tent made of 3000mm HH (Hydrostatic Head) material will keep you absolutely dry for the majority of camping trips in the United Kingdom. Tents may be equipped with a waterproof and ultraviolet (UV) coating in addition to the Hydrostatic Head of the fabric. The installation of a waterproof covering will aid in the collection of water on your tent’s surface.

Does polyurethane have BPA?

Thermoplastic Polyurethane (TPU), which accounts for the vast majority of our goods, does not require the use of BPA, BPS, BPF, or any other comparable ingredient during its production (unlike polycarbonates or epoxy resins).

How much does Pu Polish cost?

In addition to polish grades, there are also several styles and finishes available for PU (polyurethane). From Rs165 to Rs210, depending on the service.

Is the smell of polyurethane toxic?

For example, polyurethane is one of the many chemicals that are commonly used in the manufacture of new wood flooring.

It is also one that is used on a regular basis and has the potential to release a mixture of toxic compounds into the air, which can be extremely toxic when released as fumes into the indoor air. 13th of August, 2019

Is PU fabric stretchy?

The qualities of PU fabric are maintained for at least 100 cycles in the washing and dryer without causing damage to the cloth. When it comes to designing clothing, it is versatile and simple to deal with.

Why is my tent floor sticky?

One of the most typical causes for your tent to get sticky after a lengthy period of storage is that it was moist or that it was compressed too tightly when it was being kept. At the same time, if your tents are packed too tightly, the chemicals used to manufacture them (plasticizers in particular) will be unable to release their fumes.

How do you remove PU coat from a tent?

Here’s what I do in this situation. Dish soap, such as Dawn, should be used to wash it in the machine. WooLite may be machine washed a second time. Even if all of the coating is not removed, a soft nylon brush dipped in dish soap and water should be sufficient to complete the task. Please be kind! Remove the item from the washing and run it through without any soap. It should be dried on a clothesline.

Is 8000 mm waterproof good?

2,000-5,000mm waterproof rating will be more than sufficient if you are purchasing a waterproof coat for going around town or dropping the kids off at school during inclement weather. In the mountains, we recommend a rating of 5,000-8,000mm if you are considering a weekend getaway, as the circumstances might be significantly severe.

How to Waterproof a Tent

One of the most common reasons for leaks in any tent is the degradation of manufacturer treatments to the tent’s seams, DWR coating, and/or waterproof polyurethane or silicone coating. Preparing your tent for waterproofing restoration by renewing any of the treatments listed above should be done with cold water, light soap, and a soft sponge before beginning any waterproofing restoration work. This will ensure that there are no pollutants or corrosives (muck, sand, sap, animal feces, suncream, etc.) present that might interfere with the efficiency of the reproofing process.

Reapply the Polyurethane or Silicone Coating

In addition, polyurethane (PU) coatings used in tent flooring and flysheets are susceptible to chemical deterioration, which means that the PU coating will simply disintegrate with time. This is commonly detected when the covering on the tent’s interior begins to flake off in patches. If you have subjected the tent to significant abuse, you may notice small leaks in the fly and flooring that can be resolved by retreating the fly and flooring. While silicone coatings are far more durable and reproofing is rarely necessary, if you have subjected the tent to significant abuse, you may notice smaller leaks in the fly and flooring that can be resolved by retreating the fly and flooring.

  • Gather your materials, including a cloth, rubbing alcohol/surgical spirit, and the appropriate sort of tent sealant.
  • (a silicone sealant for silicone-treated fabric and a PU sealant for polyurethane-coated fabrics).
  • Lay down your tent’s rainfly and floor on a flat surface and gently wipe away the peeling covering with rubbing alcohol and a rag (if the rag isn’t working, try an abrasive sponge).
  • Follow the product directions for applying the new sealant (for more information, see our guide to the best tent waterproofing treatments).

4. 4. Thoroughly wash your hands since all tents contain flame-retardant chemicals, which have been linked to a variety of harmful health consequences. 5. Allow for a minimum of 24 hours for the new coating to dry and “cure” before repacking your tent into its stuff sack.

Renew Your Tent’s DWR Coating

The DWR (Durable Water Repellent) coating of a tent is what permits it to shed water when it is hit by rain and serves as the first line of defense against precipitation when camping. As a result, it is less durable than waterproof PU or silicone coatings and must be replaced every 10-15 expeditions, on average. Fortunately, the procedure is really straightforward. If you discover that precipitation is no longer beading up on your rainfly, you should do one of the following: 1. Gather your supplies, which should include a cloth or towel, a pail of lukewarm water, and a bottle of waterproofing spray.

  • (likeGear Aid RevivexorNikwax Tent and Gear SolarProof).
  • Pitch your tent and wet the fly with water before putting it up.
  • Apply the waterproof coating to the rainfly’s exterior in a thin, equal layer.
  • Allow the tent to dry completely before putting it back into its stuff pouch.

Reseal Your Tent’s Seams

The seams of a tent are the weakest parts in the structure, mostly owing to the hundreds of small needle holes that are formed during the process of sewing two pieces of material together. If you notice that your tent has a leak, here is the first place you should look for the source of the leak. While most tents have sealed seams, the tape or treatment that was used to produce the “seal” will need to be replaced on an as-needed basis during the course of the tent’s lifetime. Here’s how to go about it: 1.

  • 2.
  • 3) Pitch your rainfly with the underside exposed from the inside out or lay it out flat on a level surface.
  • Gently peel away any peeling tape, leaving the undamaged tape in its original location.
  • Using a rag and rubbing alcohol, wipe off each seam one by one.
  • Seal the seams with the fresh seam sealant that you purchased.
  • Allow for complete drying of the sealant before removing your tent from the ground (usually 10-12 hours).
See also:  What Do You Need To Go Camping In A Tent

What is Polyurethane Tent Coating (Essentials You Need to Know)

When it comes to waterproofing family camping tents and even backpack-portable tents, polyurethane tent coating is a technology that is frequently employed. It has both positive and negative aspects, some of which are mentioned below. Please continue reading. The majority of the family camping tents shown on our website, as well as in general, are coated with polyurethane, which is short for polyester urethane coating, and it is commonly referred to as a PU coating (polyurethane coating). When it comes to tents, the waterproof rating is determined by this factor.

  • This coating method should not be utilized in conjunction with laminates, which are significantly less common in the tent manufacturing sector.
  • Because of the rain and high gusts, they produce pressure that is similar to that experienced during a thunderstorm.
  • Having said that, I did not personally test it, but according to a statement I saw at REI, this is around 2 psi (1406 mm).
  • This will inform you exactly what you require in a tent.
  • Tents built by such European Union-based tent manufacturers often have a better rating than tents built in the United States.

A waterproof rating of 4000 mm has been assigned to the Coleman Tent Meadowood Air 4 Person, which can be seen in the top photo above. You’ll never need anything else for your camping trips with the family.

So what are good sides of polyurethane tent coating?

When it comes to waterproofing family camping tents and even backpack-portable tents, polyurethane tent coating is a strategy that is widely employed nowadays. It is not without its advantages and disadvantages, and some of them are explored in this section. Continuation after that. PU coating is used on the majority of the family camping tents seen on our website and in general, and it stands for polyurethane coating, which is short for polyester urethane coating, and it is often referred to as a PU coating.

  1. Additionally, silicone and PU/silicone coatings are available for use in lighter tents, as well as polyether urethane (PE), which is a coating that is rarely employed.
  2. Modern testing, despite the fact that waterproofness is stated in millimeters of water, pounds per square inch (psi), or hydrostatic head (HH), is done by using water pressure pumps.
  3. Nevertheless, how much pressure may be expected in such winds.
  4. Approximately 10 psi would be required in the case of a hurricane—the wind-driven force (7031 mm).
  5. In my writing about Vango ProTex Fabric, you can also find some numbers.
  6. A waterproof rating of 4000 mm has been assigned to the Coleman Tent Meadowood Air 4 Person, which can be seen in the top photo.
  • This approach is low-cost, and the low cost is reflected in the low price of the tent. For this reason, many cheap tents on the market are constructed using this type of technology
  • With aPU coating, a tent may get whatever waterproof rating it desires just by putting additional layers of the coating. So, how much are you allowed to consume? Well, let’s say it’s around 10,000 mm. It is another thing if you require it
  • See below for further information. It is possible to combine a PU coating material with fire retardants in order to fulfill CPAI-84 criteria. If you truly want to have a fire-retardant tent, it is an entirely other issue, and you may read more about it in my own book. On the other hand, silicone, which cannot be used with fire retardants, does not fall into this category.

What are downsides of the PU coating used in tents?

There are a lot of them, so here are a few examples.

Issues related to durability of a fabric when PU coating is applied

Overall, the tear strength of the cloth to which the PU coating has been applied is influenced by the PU coating. This has something to do with the slipping impact that the fibers that make up a fabric have on the surface of the cloth. Because slippage occurs in the presence of a confined pressure zone, the yarns are able to bunch together, making them less stiff and less prone to tearing. Increasing the pressure even higher will have an impact on more strands, resulting in pressure being dispersed rather than concentrated.

As a result, the fabric’s strength may be reduced.

Hydrolysis or hydrolytic stability

When exposed to moisture, the PU coating reacts, and this reaction is considerably more effective at higher temperatures. When this happens, the consequence is a sticky, foul-smelling substance that gradually loses its ability to repel water and become unusable.

As a result, it is critical to preserve such a tent entirely dry and in a cold environment. In a nutshell, tents with a PU coating have a rather short lifespan. Prepare yourself for this or consider other alternatives.

Water saturation

So the PU coating is actually hydrophilic, which may seem unusual at first, but it is true. This may become an issue only in the case of long-term camping in extremely damp places, and it is particularly relevant in the case of tent floors that have been treated with a coating of this nature. As previously stated, the process can be slowed down by applying additional layers of PU coating. The negative aspect of this is that:

  • The cloth gets significantly heavier as a result. When you store the tent, it will still need to be allowed to dry properly, which will be a lengthy procedure in the case of such a thick material. A reduction in its strength can occur as a result of the reduced slipping process described above

PU coatings and silicones can be used in conjunction to mitigate or eliminate some of these drawbacks and improve overall performance. In such circumstances, the silicone coating is applied to the fabric’s exterior side since it is extremely hydrophobic, and the PU coating is applied from the inside. Then, in conjunction with the inside PU coating, fire retardants are added to ensure that the tent meets all applicable fire safety regulations. There are a number of technical challenges that producers must contend with when applying such a diverse range of coatings, but they will not be covered in this article.

Is the PU coating toxic?

According to what I’ve been able to uncover online, polyurethane includes isocyanates, which may be damaging to your lungs if inhaled. Therefore, if you suffer from asthma, it is not recommended that you are exposed to this product. Some believe that it might also cause skin irritation. However, I have heard other people assert that once it is administered, it does not pose a threat to the user’s health. To be honest, it is so ubiquitous that it makes little sense to consider the potential health consequences of its use.

So that’s what I wanted to say about the polyurethane tent covering controversy.

Keep this site bookmarked and come back often since I update it with new materials on a regular basis, keeping you up to date.

What are Tent Fabric Specifications and Coatings?

In my research, it appears that polyurethane includes isocyanates that can be damaging to your lungs if inhaled at high concentrations. Therefore, if you suffer from asthma, it may not be advisable to be exposed to this product. Some people believe it might also cause skin irritation. On the other hand, I have heard some people state that after the product has been administered, it does not represent a threat to users. To be honest, it is so ubiquitous that thinking about its possible health consequences is almost pointless.

In conclusion, here is what I intended to say regarding the subject of polyurethane tent coatings: In the event that you have any questions, please let me know and you will receive a response as soon as I am capable of answering.

Keep this site bookmarked and come back often since I update it with new texts on a regular basis, keeping you up to date on the latest developments.

  1. A basic polyester tent fabric ideal for camping tents, but with a lower waterproof rating of 1000mm that is only suited for light rain, making it more suitable for casual camping in quite decent weather
  2. 75D 185T Polyester PU1000mm 20D 330T Ripstop Nylon Sil/PU 3000mm – a lightweight 20 Denier nylon fabric suitable for ultralight tents. It is ripstop so has better tear resistance, has a silicone coating on the topside and a polyurethane coating on the underside, and has a good waterproof rating of 3000mm, so should be able to withstand most rain. 380gsm Polycotton Ripstop – a heavier, more durable modified polyester and canvas blend suitable for swags and family cabin tents reinforced with Ripstop ‘grid’ threads
  3. Because it is canvas, it has natural waterproof properties
  4. Polycotton Ripstop – a heavier, more durable modified polyester and canvas blend suitable for swags and family cabin tents reinforced with Ripstop ‘grid’ threads
  5. A heavier, thicker polyester with a stronger weave, making it more ideal for event shelters and tent flooring. It’s waterproof, with a 3000mm HH rating, and it’s treated to provide improved protection to ultraviolet rays.

In addition to deciding on your desired tent design, you’ll need to choose a tent fabric that has the proper combination of strength, durability, waterproofness, weight, and price to match your requirements. Knowing more about tent specs can assist you in selecting the most appropriate tent. At Intents Outdoors, we take these considerations into account when designing tents that are both functional and economical. We strive to make tents that are both functional and affordable, with the ideal balance of specs and features.

What is PU Coating? Properties, Use & Environmental Impact

PU (polyurethane) coats. Anyone who has ever delved into the fine aspects of the manufacturing of outdoor apparel is likely to have come across this phrase at some stage in their research. What is the enigmatic little acronym “PU” truly stands for, though, is something you should consider. Alternatively, consider if you truly require it. Would you be able to function without it? Let’s have a look and see!

Definition, properties and effect

Start by looking up the definition of polyurethane on the internet, which we can find in our trusted internet dictionary. This will inform us that the term polyurethane – abbreviated PU – refers to a class of synthetic materials. There are three types of synthetic materials in this category: hard foam, flexible foam, and liquid formorcasting resin. In 1932, a well-known industrial chemist by the name of Otto Bayer devised the polyaddition method for the production of polyurethanes. Insulation for homes made of rigid polyurethane foam Isn’t this information really useful?

  • As the name implies, a “PU coating” is a protective film made of polyurethane that may be applied to a variety of surfaces.
  • When polyurethane is utilized in its liquid state, it may be turned into a permanent waterproofing solution for surfaces.
  • To provide textiles with an additional layer of protection, a thin coating of liquid PU is applied directly to the fabric of the garment.
  • A film of this nature might be applied once or several times.
  • Based on the intended usage for the garment, producers treat either the entire surface of the garment or only individual fibers.
  • These coatings are also extremely flexible and resilient, which is a rare combination.
  • Isn’t it wonderful?
See also:  How To Decorate Ugly Outside Of Tent For Wedding

The upsides and downsides of polyurethane coatings

The weight of a PU coating is unquestionably a significant drawback. Despite the fact that a polyurethane coating is nothing more than one (or numerous) layers of plastic, it does have a certain amount of weight to it. In reality, materials treated with polyurethane coating tend to be heavier than fabrics treated with DWR. So, if you’re looking for an ultra-lightweight outfit, I’d recommend staying away from PU-coated clothing. Outdoor gear with PU coatings is the most common use. The volume of a polyurethane coating is also significant, thus a polyurethane-coated jacket would be far thicker than a “typical” outdoor jacket.

  1. Personally, I’d prefer to dress in something that’s a little lighter and not as bulky.
  2. The lack of breathability of polyurethane-coated textiles has been a key drawback for them since their introduction.
  3. Modern technology has made it possible for PU-coated textiles to be extremely breathable as well.
  4. Essentially, this is a polyurethane covering that includes billions of small holes throughout it.

This is due to the fact that the pores are so tiny that water vapour may escape to the outside but moisture cannot get in. Voila! Breathability! Fortunately, these coatings are not as pricey as you would expect and are already frequently utilized on textiles intended for outdoor usage.

Environmental impact and uses

Of course, when it comes to environmental sustainability, there is a lot to be said about polyurethane coatings as well. It is undeniable that PU coatings are a more ecologically friendly option to many DWR treatments. To be sure, polyurethane is far from being the environmental savior that the outdoor sector would have you believe. Quite the reverse, in fact! When it comes to the manufacture and disposal of polyurethane, things may become a little hairy and complicated. However, when compared to a fluorocarbon DWR, PU is as innocent as a lamb on the pasture.

That is why so many outdoor gear businesses avoid doing business with them.

Areas of use

Clothing with a PU coating is extremely water-resistant. So, now that we’ve learned a little more about polyurethane, the coatings themselves, and the advantages and disadvantages of the polymer, we can go on to discussing the applications for which a PU coated garment is most appropriate. On a nice sunny day, no one is going to bother with a thick covered jacket when out trail running. It is during rainy and damp conditions that these clothing perform their best. As a general rule, we can state that PU-coated clothing are the most appropriate for “typical” severe weather.

  1. In spite of the fact that new coating processes have made it possible to make breathable PU-coated textiles, you should avoid using them for high-intensity aerobic workouts in poor weather.
  2. Why?
  3. For another, the coated fabric will just serve to make you feel heavier.
  4. Cordura (a polyamide fabric that is especially tough) that has been polyurethane coated, for example, can endure even the sharpest of rock edges without being damaged.
  5. That’s all there is to it when it comes to polyurethane-coated fabrics.
  6. But I hope that by writing this article, I was able to throw some light on the enigmatic polymer known as PU!
  7. It is possible to reach them by phone at 03 33 33 67058 or by email during business hours on weekdays from 9 a.m.
  8. Outdoor Clothing may be purchased here.

Restoring a shelter with a degraded PU coating

At 11:20 p.m. on July 24, 2017, 3481098 Nick GatelBPL [email protected] Nick GatelBPL Member Southern California is the setting for this story. In order to prevent hijacking the current discussion in another thread, I’m establishing a new one with this subject matter. When I talked about my Chouinard Pyramid in that thread, I said that because it is made of PU coated nylon, waterproofing it is a bit of a challenge because you have to remove the PU coating first. I need to redo mine, which will be a job for the autumn.

  1. I am not a fabric specialist, so please be aware that if I offer any information regarding textiles that is inaccurate, you will be informed:-) Over the years, I’ve been able to properly refurbish a few of polyurethane (PU) coated nylon shelters.
  2. Today, many of the bigger tent manufacturers continue to make PU nylon shelters; however, many of the “UL” tents from companies such as Sierra Designs, MSR, and others are beginning to employ silnylon or a PU/Sil nylon blend as their primary fabric.
  3. First, it’s possible that it’s leaking.
  4. Normal degradation of polyurethane (PU) results in the fabric becoming sticky when it is folded up and stored, and it may also begin to smell foul when it is folded up and kept.
  5. Vomit is the closest word I can think of to describe it.
  6. I’m not aware of any chemical that can be used to remove the PU without causing damage to the nylon.

One thing you should never do with your shelter, whether it is PU coated or silnylon, is to put it in the washing machine. If there is one exception to this rule, it is that if you wish to remove the polyurethane coating, the washing machine is your best friend. Here’s what I do in this situation.

  • Using dish detergent, such as Dawn, machine wash it once
  • Then machine wash it again with WooLite
  • If the coating is still not completely gone, a soft nylon brush dipped in dish soap and water should do the trick. Be careful with it
  • Run it through the laundry without any soap again. It should be dried on a clothesline.

Disclaimer: You are undertaking this at your own risk. If, for any reason, the washing machine causes damage to the shelter, I am not liable, I am not responsible, and I am most likely not even present. Once the shelter has been allowed to dry fully, you will need to cover the interior of the fabric with a waterproofing agent. It’s been years since I produced my own sealant formula, but McNett’s Gear Aid Tent Sure Polyurethane Sealant is a superior alternative. Follow the on-screen prompts. Some shelters may necessitate applying it in portions, with the shelter spread out on top of a huge table to prevent it from catching fire.

You’ll need to let it dry for a few days after that.

[email protected]avidinkenai David ThomasBPL [email protected] The location is North Woods.

While I agree that placing a shelter in a washing machine is always a danger, I also believe that it is necessary because:

  • Physical strains (particularly in a top-loader) can cause seams to rip
  • Pockets of water can become trapped, resulting in heavy and imbalanced loads
  • And detergent, in particular, can cause the PU coating to delaminate.

If, on the other hand, you WANT to remove the coating, and especially if you have a front-loading machine (or are willing to go to the laundromat and use their front-loader), I’d recommend using a modern detergent like TIDE rather than a milder option like Dawn or Woolite, which will remove the coating more effectively. On its own, nylon is extremely resistant to practically everything (with the exception of DEET), and it will withstand hot-water washings, a lot of detergent, and hot dryers with ease.

  1. Another advantage of a washer is that it does all of the agitation for you, so you don’t have to worry about it.
  2. There are no physical demands, and you may let it soak for hours, stirring occasionally with a 2×4 or canoe paddle, if you choose.
  3. Nick GatelBPL [email protected] Nick GatelBPL Member Southern California is the setting for this story.
  4. Others may have had success with a particular way, but I haven’t come across any.
  5. When compared to a tent, they were considerably less expensive, but they were also far more prone to malfunction.
  6. I have a Sierra Designs Clip Flashlight that is more than 30 years old, as well as a Sierra Designs Super Flash from the same era, both of which retain the original PU coating that is still in good condition.
  7. Mine have always been kept in the garage, which isn’t a particularly pleasant location in the heat of the desert.

I generally keep my shelters in my pack until it is forecast to rain or snow, which allows me to extend the life of the shelters.

Getting rid of it is certainly the best option, but reviving it will be a great endeavor for my blog.

I’m delighted to see the information contained in this topic.

I’d been storing it in the attic of my garage for a while.

Summers in Michigan are unquestionably scorching.

This insect, on the other hand, is becoming sticky and stinky.

That being said, I think it is possible that it had already begun to degrade previous to my getting it.

Thank you for providing this information, gentlemen.

Rod Unless I’m missing something, but if your tent, fly, or anything else has decaying, delaminating PU and you remove the coating in order to reapply more.

If you use a substandard PU type product, the problem will recur and most likely in the near future (i.e., the coating will not last nearly as long as the manufacturer applied the prior coating, which will be sooner rather than later).

It is also easier, faster, and more efficient to re-coat when properly applied and blended.

To attempt and wash the remainder off in order to reapply more would be pointless and time-consuming.

on August 14, 2017 3484857 I’d want to point you that a sufficient amount of DEET will dissolve practically all synthetics, with the exception of nylon.

a quote from Rodney: In the meantime, I’ve stored my replacement in a “cold, dry” environment in accordance with the instructions.” But this insect is becoming sticky and nasty as time passes.” There is a school of thinking that it might be caused by the material not off gassing, in which case the gas would be the source of the problem.

  • Franco, what kind of gas would that be?
  • Storing the fly and the inner separately may be beneficial, and I had just recently considered this, although pulling apart integral pitch tents may be a pain in the neck at times.
  • According to my research, isocyanates exist, but this is only a hypothesis.
  • Perhaps this is correct.
  • Is it possible that it is in the nature of the beast and is unavoidable?
  • Perhaps it is simply nearing the end of its useful life and requires restoration?
  • Lol “Isocyanates are chemicals that include the isocyanate group,” says the dictionary (-NCO).
  • In the production of polyurethane goods, isocyanates are the raw chemicals that are used.

During the thermal degradation of polyurethane products (such as chemicals and polyurethane foam), as well as in insulation materials and surface coatings (such as car seats and furniture), under-carpet padding (such as under-carpet padding), packaging materials (such as shoes), laminated fabrics (such as polyurethane rubber), and adhesives, Isocyanate exposure can cause irritation of the skin and mucous membranes, as well as chest constriction and breathing difficulties.

  • Isocyanates are a group of chemicals that have been designated as possible human carcinogens and have been shown to cause cancer in animals.
  • For these symptoms to manifest themselves, you will most likely have to breathe it for years on end.
  • I’m not sure when I’ll get around to restoration because there isn’t a pressing need, and as a result, my motivation is low.
  • This is, however, my understanding of the situation.
  • It was critical to get the proper polymerization for the coating to persist for an extended period of time.
  • While their coatings lasted for a few years (enough time to fulfill the warranty), the outcome was deteriorated when water was allowed to seep back in.
  • Normally, this is a difficult process that is utilized to create items such as phone covers.
See also:  How To Build A Homemade Tent

TPU, as far as I’m aware, does not deteriorate in the same manner as the earlier PU did.

The implications of this for safety are something I have not looked at.

Cheers Nick GatelBPL [email protected] Location: Southern California Email: ngatel I eventually completed the restoration of my Chouinard Pyramid PU coating, about three years after starting this discussion.

Mirazyme is frequently used to deodorize PU that has a foul odor.

@Roger CaffinBPL [email protected] Location: WollemiKosciusko National Park, [email protected] It’s very amazing.

Cheers [email protected] Thank you for taking the time to post!

I have a Sierra Designs Tiros 2 that is in excellent condition, with the exception of the fact that it has become extremely sticky on the inside.

Nick GatelBPL [email protected] Location: Southern California Email: ngatel It’s very amazing.

Roger, Patagonia gear and the company as a whole are two of my favorite things.

Not to mention the fact that Yvon Chouinard, the sole owner of Patagonia, has done so much good work outside of his company, how he runs the company responsibly, and how he treats his employees are all noteworthy.

Patagonia has truly been a pioneer in the field of outdoor clothing, and the company’s history is quite fascinating.

Understanding Layers Using Patagonia Clothing as a Guide is an article that you might find interesting.

What’s the saying, “If you learn from your mistakes, I must be a genius,” or something similar?

I had no idea this was even a possibility.

There hasn’t been any cracking or peeling yet, but it’s definitely on its way.

But for how long will it continue?

However, the majority of people today aren’t concerned with this; instead, they simply purchase a newer, lighter, and “improved” product.

However, it appears that the sticky problem occurs when the two coated surfaces are stored in close proximity to one another.

The two Sierra Design tents I have are both from the 1970s and the ’80s — one of the original Flashlights from the ’70s and a ’80s Super Flash — both are in excellent condition and were purchased prior to the Chouinard.

Could I use the Permatex Flowable Silicone for this purpose, or would it still require diluting?

Is there a particular reason you stayed with PU rather than switching to silicone?

According to my research, and I’m not an expert, PU fabrics have a coating on the inside of the material that protects it.

It appears to me that the waterproofing saturates the material on a microscopic level in both instances, which is especially true given that nylon is hygroscopic.

I was skeptical because silicone doesn’t adhere well to polyurethane.

Is what I’m saying correct or incorrect?

It just seemed more logical to go with the PU.

It has the consistency of milk and is much easier to work with than the silicone/mineral spirits concoctions that I have previously used.

14th of April, 2021 at 11:39 a.m.

Locale: IOWAHHHHHHHHH!

Years ago, I used a product called Kenyon recoat 3 to recoat a tent that I had purchased.

I followed the directions exactly, and it worked well and looked great after it was finished drying.

If Nick or anyone else has had that experience when recoating a tent, I’d be interested in hearing about it.

It is a water-based product.

It’s possible that it will wash off after that.

The material is no longer a viable option for outdoor usage and has been replaced with ‘TPU,’ which is a completely new material that is as effective.

I’m thinking of getting a new tent.

Thank you very much, Roger.

So, can I presume that the McNett Gear-aid tent sure polyurethane sealant that Nick used will have the same issues as the sealant Nick used in his tent?

Mark RiesBPL [email protected] Location: Mark RiesBPL [email protected] IOWAHHHHHHHHH! Maybe it took 12+ hours because we had an all-night downpour before packing up in the morning wet and then 6-7 hours to go to the next campground, but I don’t know.

Waterproof Tents

RightlineGon contributed to this article. Posted inTruckSUV Tent Buying Guide. When you hear the phrase waterproof, you might immediately think of those bright yellow rain coats, but in the tent world, the fabric must be quite different from those items of clothing. In addition to being extremely heavy, a tent constructed of rain jacket material would be extremely hot and moist, making it uncomfortably uncomfortable to sleep in. Tent fabric must be breathable, UV resistant, and water resistant, among other characteristics.

  • The more costly the fabric is, the higher the amount of waterproofing it has.
  • 1000mm is the minimum rating required to be considered waterproof.
  • It is possible to see the letters PU before or after a specific waterproof grade on a product label.
  • The tent fabric from Rightline Gear is certified at 2000mm PU, which is double the minimum standard.
  • We utilize it to ensure that the fabric used to construct our tents satisfies our high-performance standards of quality.
  • The waterproof coating on our tent fabric is added during the manufacturing process and is expected to last for many years.
  • There are a variety of excellent waterproofing sprays available to assist you in keeping your tent dry.
  • As is always the case, we want to keep you dry!

How to Waterproof and Seam Seal a Tent

The feeling of being snug inside your tent, listening to the crickets and cicadas sing you to sleep, is second to none—that is, until you wake up soaking wet from a leak that had gone undetected for several hours. It’s critical to waterproof and seam seal your tent to ensure that you don’t wake up in a puddle or that your camping gear isn’t ruined on your next camping excursions. When tenting in the great outdoors, there are four primary categories of challenges that tent dwellers are likely to encounter:

  • There is water leaking through the seams, which has to be fixed
  • Infiltration of water via the rainfly, which requires a water resistant coating
  • Wetness seeping into tent floor, indicating that the polyurethane covering is beginning to peel away
  • Condensation accumulates as you sleep, necessitating the need to unzip the zipper to enable more air to flow through

It doesn’t matter what kind of tent you have or what kind of leak-proofing you require; Stuff AID will assist you in keeping your gear watertight and you dry. Whether you’re camping in Yosemite or pitching up a tent in your own garden, you should prevent leaks from occurring in the first instance. Find out how to make quick and easy repairs to your tents and tarps that will last for years, so you can confidently return to sleeping quietly in the great outdoors. A puddle is hardly a place you’d like to sleep—so if you discover a bothersome loose or damaged seam in your tent, fix it as soon as you possibly can.

The most important step in completing this do-it-yourself job successfully is to choose the proper sealant for your type of fabric as well as the location and size of the treatment area.

  • A bowl of cold water
  • A sponge that is not rough
  • Revivex Pro Cleaner or light liquid soap
  • Seam Grip WP, Seam Grip FC, or Seam Grip SILWaterproof Sealant
  • Revivex Pro Cleaner or mild liquid soap

Time Estimated: Approximately 30 minutes 20 minutes are allotted for application. Duration of cure: 2–12 hours, depending on the sealant used. Steps:

  1. Set up your tent in the garage or backyard if you have one. The rainfly should be laid down flat with the underside facing up while it is being sealed. Combine 1 fluid ounce of Revivex Pro Cleaner in a basin of cold water
  2. Set aside. Preparation: Wipe down the seams you intend to seal with a moist cloth or sponge saturated with your solution
  3. Then, using the provided brush, apply a thin coating to the exterior seams of the house using the appropriate Seam Gripseam sealer. In order to seal a silnylon tent or tarp (see the chart below for reference), use a silicone-based sealer. Maintain level and allow to cure according to the directions on the container (about 2-8 hours)

Pro Tip: After the Seam Grip WP has been cured, sprinkle baby powder over the seams to keep them from sticking together. Even while a rainfly is intended to provide an additional layer of protection between your sleeping bag and Mother Nature, they can become prone to wear and tear over time as well. Fortunately, with a combination of Seam Grip and Revivex, sealing nylon from top to bottom is a straightforward process. You may now sleep easily in your entirely secure and dry tent once you’ve finished sealing any loose seams using Revivex Instant, a spray-on water repellent, and completing the reproofing procedure.

  • A bowl of cold water
  • A sponge that is not rough
  • Revivex Pro Cleaner or mild liquid soap
  • Revivex Instant Water Repellent
  • Revivex Pro Cleaner or light liquid soap

10-15 minutes is the time estimate. Steps:

  1. Lay your rainfly flat on the ground with the top side facing up in a well-ventilated place. Pour 0.5 fl oz of Pro Cleaner into a basin of cold water and stir well. Wet your sponge with the solution and use it to clean the rainfly from top to bottom. After the cloth has been thoroughly cleaned, spray it with Revex Instant Water Repellent. Make certain that the cloth is totally dry before storing it to avoid the formation of mold or mildew.

Water does not necessarily enter your tent at the top; it can also enter through the bottom of your tent and seep up through the floor. It’s a circumstance that will undoubtedly cause you to awaken from your lovely slumber fast (and painfully). Use Seam Grip TF to repair the polyurethane (PU) protective coating on the bottom of your tent to prevent water from seeping up through the bottom of your tent.

  • The following items are required: dry brush, isopropyl alcohol, Revivex Pro Cleaner or mild liquid soap, Seam Grip TF Tent Fabric Sealant

Time Estimated: Approximately 30 minutes 15 to 30 minutes for application Cure time is 8-12 hours. Steps:

  1. Using a dry brush and isopropyl alcohol, remove the old, damaged PU coating from the surface. Alternatively, you may soak the tent in a solution of water, Revivex Pro Cleaner or mild detergent, and an isopropyl alcohol combination to remove the previous PU covering. Following cleaning and drying the area, shake Seam Grip TF and push the sponge down while pinching to saturate the applicator with product. Apply a thin, uniform coat of paint to the fabric of the tent’s inside. It is recommended to use a single coat. After four hours, check the tent for dryness and wait 24 hours before storing it away.

When the factory PU coating starts to peel and flake off, it’s time to replace it, according to our experts. It may also grow sticky or emit a terrible stench as time passes.

Leave a Comment

Your email address will not be published. Required fields are marked *