How To Replace Snaps On Tent Trailer

Quick Answer: How To Replace Snaps On Tent Trailer

Place the fabric right side up on a level surface and insert the flathead screwdriver between the top and base of the socket closure: the socket and stud. Repeat this process for the other side of the cloth. The screwdriver should be placed between the cloth and the stud. As you lift the screwdriver, the snap should spring off.

Can you reuse a jean button?

When it comes to jeans buttons, one of the best things about them is that they are often composed of metal and can be reused. They are not difficult to remove, nor are they difficult to reattach. Simply using raw force and a little arm power will enough in obtaining the grasp you want.

Can you reuse snap fasteners?

Because the snap components are damaged, they should not be reused; instead, they should be discarded and replaced with new ones. Because of the screwdrivers that are included in the handle of our Perfect Hammer, it is excellent for snap removal.

What are snap fasteners used for?

A snap fastener (also known as a press stud, dome fastener, popper, snap, or tich) is a pair of interlocking discs, usually made of metal or plastic, that are widely used in place of conventional buttons to fasten garments and other items of clothing that require fastening.

Can you glue snaps to fabric?

You may use lightweight fabric with metal snaps, but you must add a layer or two of interfacing to the garment, both for thickness and to prevent the small spikes from ripping holes in the fabric surrounding the snap.

Do I need interfacing for snaps?

In order to assist reinforce and preserve the cloth surrounding the fasteners, we recommend that you use an interfacing. Make use of a sew-in material, such as woven/non-fusible interfacing, twill tape, or a comparable weight cotton fabric for the best outcomes possible.

Are old snap on tools worth anything?

In general, the tools that still serve a purpose (such as sockets, ratchets, and wrenches) have a monetary worth. In general, tools in sets are more desirable than tools purchased individually. As a result, although a vintage 1950s socket set is valuable, a vintage 1950s headlight beam focus tool is not. Snap on tools from before World War II are the most precious.

How do you attach snaps?

Place the snap cap on the plastic platform so that it is right side up and the metal prongs are facing up. Then insert the socket into the plastic ring on the other side of the socket. The raised side of the socket should be facing the snap cap when the socket is assembled. Firmly press down on the socket to ensure that it is securely fastened in the pliers.

How can I make my purse magnet stronger?

Here’s how to make specific magnets even more powerful: Magnets made with iron bar Fill a large basin or pan halfway with water. Magnets that have lost their magnetic force It is possible to recharge a magnet that has lost part of its initial charge on occasion. Magnet stacking One method of making weak magnets stronger is to stack a large number of weak magnets together.

How do I fix the snap button on my wallet?

How to Disassemble and Reassemble a Wallet Snap Remove the snapper that has broken. Carefully pry beneath the snap with your fingers.

Take a look at your wallet. Make sure the hole in the leather is the same size as the snap by using a leather awl. Take the snap tools out of the packing and set them aside. Organize your wallet by layering it. Attach the top of the snap to the top of the snap. Reinforce the snap with a second snap.

Can I return Snap On Tools?

The customer has 30 days from the date of delivery to return any Product purchased from this Site (with the exception of items that have been specifically designated as non-returnable by Snap-on). A Return Goods Authorization form (“RGA”) must be obtained from the manufacturer by calling 1-877-762-7664 or sending an email to to request a return request.

How do you attach a rivet button?

INSTALLING JEANS BUTTONS AND RIVETS INSTRUCTIONS you will require the following materials: Make a hole in your cloth with your awl or nail that is just large enough to allow the button or rivet tack to be put through it. Push the tack all the way through the cloth, starting at the rear and working your way forward. ONLY APPLICABLE TO RIVETS. Place the button or rivet face down on the metal surface you’ve chosen. Lightly pound the tack’s backside to secure it.

How do you replace a broken Snap On Tool?

RIVETS AND BUTTONS FOR JEANS – INSTALLATION GUIDE What you’ll need is a few supplies. To begin, create a hole in the cloth with an awl or nail that is just large enough to accommodate the button or rivet tack being pushed through. Then, starting from the rear of the garment and working your way forward, thread the tack through. RESERVED SOLELY FOR RIVETS Place the button/rivet face down on the metal surface that you’ve chosen for this project. Striking it lightly with your thumb can help it to stick better.

Which snap pliers is best?

Take a look at our pick of the greatest solutions listed below. Snap Pliers from Babyville Boutique. These pliers are a fantastic all-purpose tool, especially for working with plastic snaps. Dritz Heavy Duty Snap Pliers are a pair of heavy-duty snap pliers. KAMsnaps Plastic Snaps Tool with a Hand-Held Pliers. DianMan Heavy-Duty Snap Fastener Pliers are made of high-quality steel. We R Memory Keepers Crop-A-Dile Eyelet and Snap Punch are two of their most popular products.

How do you do the button Jean trick?

The basic concept is that you thread the belt loop closest to the large button on your jeans around the button, so tightening the waist of your pants. Then you button and zip up your jeans as you normally would, and presto! You’ve officially upgraded to a better-fitting pair of jeans.

Why is snap on so expensive?

The increased expense is due to significantly more research and development as well as significantly superior engineering of the tools and other equipment. As a result, the price is slightly higher. Then they utilize higher-quality steel to create a more durable instrument. Consider the difference between a Craftman Cast tool and a Forged steel tool.

Does Big W sell buttons?

Make your works more enjoyable to look at by including the 5 Pack of Buttons from Create Handmade in them. These white buttons are guaranteed to add a touch of elegance to any ensemble! Product Specifications: 5 Pack.

How do you fix a broken wallet?

The tiny quantity of loose leather on each side of the tear should be lifted up and a light layer of garment glue applied to the inner border of the rip should be effective. Apply mild pressure with your fingertips to the leather patch on one side of the tear to ensure that the glue is properly secured.

How do you take off a jean button without breaking it?

Insert the head of the screwdriver between the rear of the rivet or button and the back of the button or rivet.

Move it around a little to help loosen it up a little more. Now, with the pliers, grasp the top of the rivet or button and twist it up and down to free it from the bottom of the button or rivet.

Amazon.com: RV Designer A304, Window Covering Hardware, Snap Kit with Tools, Fabric to Wall, Six Fasteners : Automotive

Style: Fabric to WallVerified PurchaseReviewed in the United States on May 25, 2018Style: Fabric to Wall These were quite effective. These are not included in the price of the other seller, but this kit does contain the tools you’ll need to put them together and punch the hole in the cloth. There is another vendor of wall snaps that sells a product that is virtually the same as the first, but does not include the equipment. The ‘cap’ side is divided into two sections: the top, which has a small tube, and the bottom, which contains a hole.

  • The cap is connected to the section of the pipe that is inserted into the wall.
  • At roughly $2 per unit, the price is a little excessive considering what you get.
  • Although the fabric punch became progressively dull as I used it, it was still adequate to produce six holes, as there are six’sets’ of fabric punches in the box.
  • It is simple to use, and the instructions are presented in a way that demonstrates how to utilize it.
  • I intend to make another purchase.
  • I was hoping that these snaps would be compatible with the ones I have in my camper, and they are.
  • The fact that they are the same size means that all I have to do is attach the male end of the snap to the curtain fabric.

According to the manufacturer, these snaps are normal RV size.

On July 22, 2019, a review was published in the United States of America.The style is Fabric to Wall.

Despite this, there were a few parts of the puzzle missing from the packaging.

If I hadn’t realized this until after I had already begun installing them, I would have returned them to the store for a refund.

On December 4, 2021, the United States will conduct a review.

Fabric to Wall Style, verified purchase, reviewed on February 17, 2019 in the United States of America.

Includes all of the equipment necessary to attach a snap to a wall as well as a curtain.

Style: Fabric to the WallVerified PurchaseReviewed in the United States on June 16, 2014Style: Fabric to Wall I used this to replace snaps in a RoadTrek RV that had become rusty.

The disadvantage was that the wall snaps were equipped with captive screws that were just around 1/2 inch long.

This kit would be significantly improved if the screws and wall snaps were packaged separately, allowing for the use of longer or shorter screws as desired.

On June 24, 2017, a review was conducted in the United States. It does the job when it comes to mending Roadtrek curtain slides on windshield curtains. Style: Fabric to WallVerified Purchase

Top reviews from other countries

5.0 stars out of 5 for this product Perfect On March 1, 2019, the Canadian government reviewed the document. Style: Wall to WallPurchased with confidence 5.0 out of 5 stars, and very simple to use On October 1, 2017, it was reviewed in Canada. Finished Product: Fabric to WallVerified Purchase It worked perfectly and was simple to use. 4.0 stars out of 5 for this product Four out of five stars On May 21, 2018, a review was published in Canada. Style: Fabric to the WallIt appears that a verified purchase is sufficient.

Amazon.com: Fasnap Premium Snap Fastener Snap Repair Kit

On November 17, 2017, it was reviewed in the United States and verified as a purchase. I used them to fix my Condor HHR Pouch, which I use to carry a tiny two-way radio when working outside. They worked well. Despite the fact that the bag was excellent, the belt fastening snap was of worse quality and broke. The Fasnap repair kit worked perfectly and was far superior than the original snap in terms of overall quality. I don’t understand the negative feedback. My recommendation is to work on a firm, stable surface before attempting any repairs or replacements.

  1. Take your time, and you will be rewarded with a high-quality repair.
  2. If you hammer too hard or for too long, the result will be visible on the “finish” outside side of the door.
  3. It’s been more than a month and I have no regrets.
  4. Purchase that has been verified It was used to mend the leather on my motorbike gear.
  5. verified purchaseReviewed in the United States on February 24, 2018Verified Purchase On October 20, 2019, a review was conducted in the United States.
  6. As advertised, this product was utilized to secure the snaps on our pop-up camper’s tonneau cover.
  7. The pricing was also a little less expensive here than it would have been directly from the manufacturer.
  8. Purchase that has been verified On March 23, 2016, a verified purchase was made in the United States.
  9. Delivery in a short period of time Reviewed on January 27, 2017 in the United States of America Verified Purchase was short one side of the jacket, which prevented both sides of the garment from being completed.
See also:  How To Put A Tent Back In The Bag

Canvas velcro replacement/alternative?

You are currently using an out-of-date web browser. It is possible that this or other websites will not show correctly. You need either upgrade your browser or switch to another one. What are the alternatives to using Velcro to secure the camper to the vehicle. I have either an accordion or a hard-sided pop-up tent. It’s old and the velcro isn’t sticking anymore. Do you have any suggestions? I tried to include snaps, but had very little success. Because the snaps you buy from Ace Hardware and other places fail so readily, I have to replace them on a regular basis.

  • After that, glue it to the dog and have it sewed into the canvas by a professional.
  • It has been in place for two seasons and is still going strong.
  • After that, glue it to the dog and have it sewed into the canvas by a professional.
  • It has been in place for two seasons and is still going strong.
  • Additionally, depending on the configuration and wind conditions, there is a significant amount of stress at the point where the canvas and wall come together.
  • I have a dog who enjoys poking his snoot out of the canvas and wreaking havoc on the surroundings.
  • I’ll have to look for a better snap crimper for the button part of the project.

I had also pondered incorporating a zipper into the design in some way. That would be a viable option. Thank you, ROO. I was thinking about the photographs. That problem appears to be identical to mine. A large number of campers make use of elastic ropes and hooks.

Door support snaps that hang from ceiling?

You are currently using an out-of-date web browser. It is possible that this or other websites will not show correctly. You need either upgrade your browser or switch to another one. I recently acquired a 1999 Coleman Mesa and am in need of replacement parts for a few of damaged components. The first is a strap-like structure that hangs from the ceiling and provides support for the door when it is fastened to the ceiling. It is not the cable support that moves on the track, but rather the nylon type strap that provides additional support so that the door does not dangle from the wires when it is mounted to the roof.

  1. A portion of it is still embedded in the ceiling.
  2. On the bunk ends, the second component that’s damaged is the bungee type cable that’s hidden beneath the canvas and is responsible for keeping the canvas taut.
  3. I’m new to popup camping and would much appreciate any assistance!
  4. We recently went to Walmart and got a four-pack of extra-long(green) bungees for just three bucks, and they function even better than before.

Hoomi

I’m acquainted with those straps because we have a Coleman Nevada from 1999. But if you need any dimensions or other information, I can email you close-up images of ours if you’re interested in learning how to make one. The bungee cord on the end canvas was changed by me this past year because one of ours had snapped. I went to Summit Hut, which is a local outdoor supplies store. Any business that offers rock climbing equipment should be able to provide bulk bungee rope at a reasonable price.

  • The ultimate result was that I had to pass a strong wire through, which was difficult since it kept catching at the seams, and then use that wire to draw the new bungee through.
  • Welcome from Wisconsin, where you may find me driving a 1998 Mesa.
  • If you are able to remove it, you might consider purchasing some nylon strap from a retailer such as Walmart or a fabric store, and using it to create a new one.
  • In the meanwhile, I’m confident that someone on this forum will be able to assist you.
  • I recently had to repair my door hanger, which was a really simple task.
  • The snaps are simple; I just stopped by Menards and purchased a package of new snaps.
  • I used a pop rivet to reattach the piece to the ceiling, just as the original did.

A replacement shock cable may be found on Ebay for a reasonable price.

Simply drill out the old rivet and replace it with a screw, and you’re done.

Thank you for visiting the Portal and best of luck!

The door hanger is most likely pop riveted into the ceiling (as is the case with my ’08).

What kind of screw are you talking about?

Do you know the dimensions of the pop rivets?

I’m contemplating purchasing a rivet gun in the near future.

I recently had to repair my door hanger, which was a really simple task.

The snaps are simple; I just stopped by Menards and purchased a package of new snaps.

I used a pop rivet to reattach the piece to the ceiling, just as the original did.

One of the screws wouldn’t hold in place for the first couple of tries, and in retrospect I should have just used a screw instead. Do you happen to know what size rivets you employed? Is there a site where I can find the appropriate size? Thanks!

Replacing – Repairing Snap Caps

Greg A is now unavailable. 8 hours 32 minutes ago, someone looked at it. 11/02/2013 – 20:45 – Added to the group Due to the fact that we’re in the White Mountains of Arizona, I can’t recall the precise lengths and I don’t have my materials in front of me at the time. The curtain rods were 1/8″ in diameter and came in two lengths of 3/16″. Rivets are difficult to come by these days, and HomeD/Lowes aren’t really reliable sources. Everything I needed was available at ACE except for the long 3/16″ which I had to get from Amazon.com.

  1. Monday, July 10th, 2017 – 14:45 43 LupineOffline The last time I saw her was 5 months and 3 days ago.
  2. It’s past time to repair some of the rivets, especially on the roof, and it’s been a while.
  3. On the outside, there are various different sorts of rivets or screws to choose from.
  4. So, first and foremost, how can I fix fiberglass cracks that have formed around an old rivet?
  5. Alternatively, can I apply sealant around an old rivet and washer without removing it and then cover it with a cap?
  6. p Lupine /p (Lupine) Greg AOffline on Monday, July 10th, 2017 at 15:5344 8 hours 32 minutes ago, someone looked at it.
  7. When the gel coat is pressured as a result of the pressure of the rivets, the gel coat will eventually shatter.

The majority of crazing around the rivets isn’t problematic and won’t leak until it extends to the point where the underlayment is visible.

Ensure that you have read through the rivet/snap cap sections in the maintenance table of contents if you haven’t previously.

Snap caps are used to cover the interior of rivet barrels in order to prevent leaks from occurring there, as well as to provide a washer beneath the head of the rivet, which allows the rivet to be tightened down against the shell.

When I replace rivet barrels, I use butyl tape wrapped around them as an extra measure of sealing using a substance that will last a very long time and will not cause a mess as sealant will do.

In approximately 4 hours, my daughter and I completed the whole Scamp 13 project, and I’ve reworked my Scamp 19 project by splitting it down into chunks and spreading it out over several weeks.

LupineOffline 5 months have passed since the last sighting.

I’ll have to show my husband:-).

Reading through this section on rivets or screws has revealed a plethora of useful information to me.

We reside in a little town in California (yes, there are a few of those around here), and finding someone who can perform trailer maintenance has proven to be a difficult task.

By the way, if anyone is planning on traveling to Oregon on August 21 to witness the spectacular complete solar eclipse, we will be in two campgrounds along the area of totality: Cinder Hill and LaPine campgrounds, respectively.

p Lupine /pGordon2Offline Lupine /pGordon2Offline 3 months and 3 weeks ago, I was last spotted.

Use scrap material to PRACTICE making rivets and drilling them out without destroying the scrap material you are working with.

Make an effort to keep the thickness the same.

Scampor is most likely where I would get my rivets from.

but in the state of South Carolina Tuesday, July 11th, 2017 – 14:4747 ELongestOffline The last time I saw her was 1 day and 17 hours ago.

3 days have passed since Posted on: September 22, 2014, 13:33 Once again, thank you for your extremely useful suggestions.

I’ll see if I can get any fiberglass scrap.

p Lupine /p (Lupine) Friday, August 18, 2017 – 12:4349 It was just the two of us and the dogs.

This may be a beginner’s question, so please bear that in mind.

The rivet itself appears to be in good condition, however the cap is simply lying there, and I can easily flip it around.

I don’t have any spare caps, and this one seems just like the others, except that it’s a little loose.

I’m hoping to get this taken care of before we depart on our trip tomorrow.

CatherineCampingwithdogs Friday, August 18, 2017 – 12:58:50 Greg A is now unavailable.

11/02/2013 – 20:45 – Added to the group The presence of a loose cap is not a problem in and of itself until the cap comes off easily when pulled.

As a result, if it is loose and just pulls off, you will most likely need to repair the base as well as the cap.

The date and time of joining is: 08/07/2017 19:30 We are in the process of installing a front cabinet, and I came over this discussion when trying to figure out how these acorn nuts are inserted on the interior of the scamp.

The acorn nuts are discussed in this thread, but I came across another pretty nice explanation and wanted to share it with anyone who might be interested in a few additional information about them.

Pages

Boat cover snaps can grow slack and even disappear over time as a result of regular use. During this time, dust, dirt, and debris can build on your craft, causing gel coat finishes to get damaged and causing other costly damage as well. We recommend that you have some boat cover repair supplies on hand in case you need to do a rapid repair. This manner, if you are doing maintenance duties and notice a loose or missing snap, you may replace it as soon as possible. A missing snap will not do any harm to your boat while it is in storage, and you will not be required to purchase a new cover because of it.

Keep a Supply of Boat Cover Snaps and Fasteners Onboard

Listed below is a proposed list of goods to have on board in case of emergency repairs:

  • Broken snaps may be pryed out of a boat cover with the DeckMate multi-purpose tool by Ironwood. Other tools available include the Top-Snapper by Taylor Made, which ensures perfect snap alignment, and a range of new snaps from Taylor Made to fix any boat cover. Don’t forget to bring along your SeaSenseSnap Fastener pliers, which will help you do repairs faster and save your hands. Snap Fasteners for windshield mounting are difficult to come by. They are available at Wholesale Marine! We also have boat cover snaps and fastening kits from Attwood and SeaSense to make the work go more quickly and ensure that the finished product is professional-looking.

Online shopping at Wholesale Marine gives you the convenience of getting anything you need for your boat just when you need it. We provide reasonable prices as well as same-day, flat-rate delivery on the majority of our merchandise. Our customer service representatives would be happy to answer any questions you may have about boating and to give professional advise when necessary. Make sure to inquire about our Captain’s Club Reward program when you visit! The number to reach us is (877) 388-2628, and we’re available Monday through Friday from 9:00 AM to 6:00 PM Eastern Standard Time.

See also:  How To Pee Inside A Tent

Installing screw-in snaps for outside sun shades

This discussion is proudly sponsored by:
Please support our sponsors and let them know you heard about their products on iRV2
06-04-2008, 08:06 AM 1
MemberGulf Streamers ClubJoin Date: Mar 2007Posts: 58 Can anyone tell me if they have installed those screw in snaps to the outside of their motorhome to snap on those outside sun shades? I know I have seen them on other RV’s but when I asked the service department at local dealer they said no and suggest the magnetic shades. Don’t see how that will help as the outside is fiberglass. Ours are held in place by velcro and it gets very dirty. Thanks for any help.Betty
Join the1 RV Forum Today – It’s Totally Free!iRV2.com RV Community -Are you about to start a new improvement on your RV or need some help with some maintenance? Do you need advice on what products to buy? Or maybe you can give others some advice? No matter where you fit in you’ll find that iRV2 is a great community to join. Best of all it’s totally FREE!You are currently viewing our boards as a guest so you have limited access to our community. Please take the time to register and you will gain a lot of great new features including; the ability to participate in discussions, network with other RV owners,see fewer ads, upload photographs, create an RV blog, send private messages and so much, much more!
06-04-2008, 08:06 AM 2
MemberGulf Streamers ClubJoin Date: Mar 2007Posts: 58 Can anyone tell me if they have installed those screw in snaps to the outside of their motorhome to snap on those outside sun shades? I know I have seen them on other RV’s but when I asked the service department at local dealer they said no and suggest the magnetic shades. Don’t see how that will help as the outside is fiberglass. Ours are held in place by velcro and it gets very dirty. Thanks for any help.Betty
06-04-2008, 08:18 AM 3
Senior MemberWinnebago Owners Club Workhorse Chassis OwnerJoin Date: Aug 2007Location: Sonoma County, CAPosts: 5,989 I have the snaps on my coach and they work great. The installer pop riveted them instead of using screws. He said the pop rivets hold better and they don’t come loose like screws._WayneRoberta and Maggie the Miracle Dog08 Winnebago Destination 39W Gas UFO Workhorse Chassis.Never make a woman mad. They can remember things that haven�t even happened yet.
06-04-2008, 08:24 AM 4
Senior MemberWorkhorse Chassis OwnerJoin Date: Mar 2005Location: Savage, MDPosts: 233 I would NOT use pop rivits that come with the snaps. they will corrode with time.I would go to West Marine or the likes, and buy6 3/8″ Pan Head Sheet Metal Screws (stainless steel.)You should fit the whole cover using blue masking tape. Fairly tight, though not drum tight, as they shrink a little. Once it is fitting exactly how you want it, then you can mark where each snap goes. I did one at a time, with no trouble. Be careful that where you want to put a male snap is not on top of something you can’t drill.Drill the correct pilot hole. If you don’t know the size, start a little small. If the pilot hole is too small, you will be able to get the screw in, but it will shatter the gel coat.Once I got the screw in, I took it out, and put a very thin layer of clear silicone glue/sealant on it. Adds just a little bit of insurance on water seapage, and makes it easy (becasue it is slippery) to get very tight._Bill N8HDWNancy N8HDV2005 Sea Breeze 8341 on W-22 Chassis2008 Saturn Vue I-4
06-04-2008, 09:26 AM 5
Senior MemberMid Atlantic CampersJoin Date: Feb 2006Location: McVeytown, PAPosts: 2,259 I agree with blues method. I use construction adhesive (liquid nails) on the screws. This will insure they never come loose and it seals the snap to the fiberglass. I use a tooth pick or such to clean up what ever squeezes out from around the snap. Have used this method on 3 Motorhomes_Steve, Pat, Hakbar,Root Motor2007 National RV Pacifica 36′
06-04-2008, 09:59 AM 6
Senior MemberNewmar Owners ClubJoin Date: Jul 2006Location: Wellington, FloridaPosts: 13,599 I did all the windows on my coach. Bill gave good instructions and the kit should also have instructions. Using the adhesive, of your choice, like Steve mentioned works very well. My snaps have been on the coach 2+ years without any problems.I purchased the shades from MCD._Gary2005 Newmar KSDP 3910 + GMC ENVOY XUV 37K lbs Moving Down The Road The Avatar Is Many Times Around The USANobody Knows Your Coach Like Somebody Who Owns One Just Like Yours
06-04-2008, 11:42 AM 7
MemberGulf Streamers ClubJoin Date: Mar 2007Posts: 58 Thanks, all. I have ordered the snaps. I felt like it was doable, but the guy at the RV place seemed to think I had lost my mind. I was checking to see if he had the screw in snaps. Again thanks.Betty
06-04-2008, 11:58 AM 8
Senior MemberWorkhorse Chassis OwnerJoin Date: Feb 2005Location: western wa.Posts: 552 after you drill the pilot holes use a bigger bit n spotface the holes. this will stop the gellcoat from breaking out. if you have a calliper check the root diameter of the screw n use that size for pilot holes. get the twist locks. they work best. dave_2007 NRV DOLPHIN LX 6342WORKHORSE W-22
06-04-2008, 04:06 PM 9
Senior MemberMid Atlantic CampersJoin Date: Feb 2006Location: McVeytown, PAPosts: 2,259 I usually reem the drilled hole with a larger phillips head screw driver, that takes care of the gel coat. I hopeId hate to see ya push a little to hard and go through with that second drill_Steve, Pat, Hakbar,Root Motor2007 National RV Pacifica 36′
06-04-2008, 08:14 PM 10
Senior MemberJoin Date: Dec 2006Location: Atlanta, GA., South Beach, FL. Naples, Fl, Coral Gables,FL.Posts: 1,112 Mine was installed with the6 3/8 ” pan head Sheet metal Screws (Stainless steel). never had a problem and I leave it on when in storage or just in the driveway and always at the camp sites. I even had the entry door window made for the black sunscreen the outside snaps on the screens are all black.
06-05-2008, 04:03 AM 11
Senior MemberMonaco Owners ClubJoin Date: Jun 2003Location: St. Cloud, FLPosts: 1,528Blog Entries:1 Mine were installed with aluminum pop rivets 5 years ago. I’ve never had a problem with them. They are still as tight as when first installed.This is also the factory recommendation to install window awning brackets, just heavier duty aluminum pop rivets._Bob2006 MonacoCamelot 40PDQ US Navy Carrier Battlegroup 1959/1965 Winters in Florida, Summers in Blue Ridge Mountains
06-05-2008, 05:03 AM 12
MemberGulf Streamers ClubJoin Date: Mar 2007Posts: 58 Thanks for the replies. I have ordered the snaps. Now hoping they will get here so we can put them on before heading for the big re enactment at Gettysburg. Have been told it will be very, very hot. If not will leave the velcro for just a little longer.Betty
06-05-2008, 05:05 AM 13
Senior MemberJoin Date: Feb 2003Location: Jarrell, TX 76537Posts: 4,498 I installed my shade this way. I used a dab of silicone sealer behind the snap. It seals and acts as a glue, but it is NOT impossible to remove if necessary. If I had it to do over I would get the “roll on” version of the shades. No snaps, no ladders etc._DaleAKA – Oemy
06-05-2008, 05:40 AM 14
Senior MemberTexas Boomers ClubJoin Date: Dec 2003Location: Mo/TexasPosts: 3,549 BLOCKQUOTE class=”ip-ubbcode-quote”div class=”ip-ubbcode-quote-title” quote: /divdiv class=”ip-ubbcode-quote-content” Originally posted by oemtech:I installed my shade this way. I used a dab of silicone sealer behind the snap. It seals and acts as a glue, but it is NOT impossible to remove if necessary. If I had it to do over I would get the “roll on” version of the shades. No snaps, no ladders etc./div/BLOCKQUOTEWhy the roll on versus the snap kind?
Currently Active Users Viewing This Thread: 1(0 members and 1 guests)
Posting Rules
Youmay notpost new threadsYoumay notpost repliesYoumay notpost attachmentsYoumay notedit your posts


BB codeisOn SmiliesareOn code isOnHTML code isOffTrackbacksareOff PingbacksareOff RefbacksareOff


Forum Rules

Similar Threads
Thread Thread Starter Forum Replies Last Post
Sun Shades JohnTerri Excel Owner’s Forum 20 02-10-200903:45 PM
Front window interior retractable sun shades Alpine 2004 Alpine Coach Owner’s Forum 3 11-10-200806:34 AM
Sun Shades – Recommendations? RVersOnline Alpine Coach Owner’s Forum 8 08-18-200609:15 AM
Sun Shades Cedar41 Alpine Coach Owner’s Forum 3 08-02-200603:20 PM

Boat Cover Snaps Repair Tips for the DIY Boat Owner

Our store has a new look, and there will be more improvements in the future! The following are the highlights of Boat Cover Snaps Repair:

  • Boat Snap Toolkit Essentials
  • Tips for Installing Boat Snaps in Canvas
  • Tips for Installing Screw Studs
  • Tips for Boat Snap Repair
  • Other DIY Repair Items
  • The DIY Boat Snap Toolkit Essentials

DIY Boat Cover Snaps Repair Toolkit

Snap setter for boat cover snaps is a repair tool. Scissors with a good edge Pencil with a sharp point Screwdriver with a narrow 1″ tip and a flat head design in chalk A hammer or mallet is a tool used to strike something. Block of wood with the end grain on one side Drill bits made of cobalt or titanium Plastic 1/8″, 9/64″, 5/32″, and 3/16″ Anchors for the wall 8-10 x 3/4 inch holes in the fiberglass for enlarged openings Dot ®Fasteners are the most common type of boat snaps that you will need to install for boat cover snaps repair.

Dot Fasteners are a type of fastener that is shaped like a dot.

In addition, when boat cover snaps actually pull through the canvas as a result of a tear or an enlarged hole in the canvas, this is a very frustrating problem.

On our boat cover repair page, you can learn how to sew on a patch.

Stainless Steel Durable Button Stainless Steel Durable Socket

Installing Dot and FasnapBoat Snaps in Canvas

To set snaps, professionals generally rely on the Pres-n-Snap ®tool, which was developed by Hoover. If you want a professional crimp for your boat cover snaps repair, the press type tools are your best option, despite the fact that they are more expensive. Snaps on boat covers can be set with an anvil-style set tool, such as the heavy-duty anvil that we sell that is shown below. The quality of the crimp will vary depending on the quality of the anvil type tool used. This one, in conjunction with the stainless steel snaps that we sell, will perform an excellent job of repairing your boat cover snaps.

  • The vice grip tools shown below will make your boat cover snaps repair a bit faster, and there will be no pounding necessary to complete the job.
  • It is also quite simple to misplace the dies.
  • Click here to learn more.
  • When it comes to conducting your boat cover snaps repair, they are totally suitable in any weather condition.
  • The distinction between these pliers and others is that the dies are soldered to the pliers.
  • Caps and sockets are designed to fit into the screw-in studs that are typically found in fiberglass boats all over the world.

DIY Tip: Because the vice grips in this kit are larger than typical, it is not recommended that you purchase the dies separately because they may not fit on the tool you already have at home for your boat cover snaps repair.

Installing Curtain/Twist FastenersLift-The-DotFasteners

This approach is not practicable for the do-it-yourself boater since it requires the use of a costly hand punch tool, which is not available to them. Unless otherwise specified, the curtain fastener (twist fastener) and Lift-The-Dot fasteners are composed of two parts: the male top side with four prongs and the female backingplate, which sandwiches the fabric between itself and the male side. The prongs crimp down and grip the backing plate with a strong grip. Both of these snap fasteners for boat covers may be placed with a little patience and without the use of any costly tools at all.

  • With the end grain facing up, a block of wood, a flat tip screwdriver that is 1/8″ to 1/4″ broad, a hammer, a pair of scissors that are sharp, chalk, and a sharppencil for marking are all required.

In order to prevent a snap from ripping through a canvas, it is necessary to first strengthen the canvas where the snap will be attached. If you need to fix the canvas first, go ahead and do so. 2. Make a mark on your cover where the fastener will be placed. 3. Mark the points of the prongs on the male side of the fastener with chalk to indicate where they should go. Place the chalked prongs over the original snap mark on the cloth and press the prongs’ tips on the fabric to transfer the chalk marks.

  • Turn the four-pronged male fastener over, then place and mark the oval center hole that is between the four prongs on the other side of the fastening.
  • Using your small tip flat head screwdriver and a hammer, punch the holes for your prongs into the cloth, which will be supported by a piece of wood.
  • Make sure not to make the central hole any larger than necessary.
  • The installation of a fine, new fastener and completion of your boat cover snaps repair have both been accomplished satisfactorily.

Installing a screw stud into your boat

A8 screw base is used for both basic screw studs and Lift the Dot studs. These require a drill bit of either 1/8″ or 9/64″ in diameter. If you want to check the thickness of the fiberglass in your boat, always start with a 1/8-inch drill bit. After you have drilled a hole in fiberglass, you will need to countersink the hole to ensure that it is properly sealed. This simply means that you must remove the sharp edges of the fiberglass from the aperture of the hole before continuing. If you don’t have a countersink, you may use a 2 Phillips head bit in your drill to countersink the top of the hole until it is flush.

  1. Countersink Hole (also known as a countersink hole) Apply forceful downward pressure to your 8 screw stud or your Lift-the-Dot ®stud as you twist it into your fiberglass hole to ensure that it is secure.
  2. You should stop if you encounter excessive resistance or if the fiberglass seems too thick as you go.
  3. Now change to your 9/64-inch drill bit and re-drill the hole once or twice more.
  4. If you feel the need, you can drill all of your holes with the 1/8 inch drill bit and test them.

You can always go back and drill them with the 9/64 inch drill bit if you are not satisfied with the results. In this way, you will be able to gain a feel for drilling through different thicknesses of your boat’s fiberglass.

Installing screw studs into aluminum

If you use the proper drill bit and Phillips head bit, you can put a screw stud into thin aluminum without damaging it. Aluminum is commonly seen on windshields and pontoon railings, among other places. For metal, I use a 9/64-inch drill bit. Using this size hole, you may test your screw again. If the aluminum is too thick and you encounter too much resistance, you can increase the size of the screw to a 5/32″. If you’re utilizing pop rivets in conjunction with a dot stud, a 1/8″ bit should be plenty for the job.

It happened to me once over my 30 years of doing this, and getting the glass replaced was a major hassle.

How to repair boat cover snaps

Several options are available if your boat snaps have torn out of the fiberglass and created an unintentionally huge hole. The first option would be to experiment with a screw stud with a 10 screw base to determine whether it is large enough to hold in the fiberglass before moving on. Keep the smallest size accessible aboard your boat, which should be between an 8 and a 3/4 inch in diameter. Several options are available if your boat snaps have torn out of the fiberglass and created an unintentional enlargement hole.

Ensure that you have the lowest size possible on your boat, which should be between 8 and 10 by 3/4″.

DIY Repairs

If you require any more goods for your DIY repairs, please see our boat cover repair kit and thread supplies, which may be found further down this page. We’ve also included Durable Dot ®Eyelets and Studs to make things easier for you. We also offer a large selection of boat canvas materials to pick from. Take a peek at the website provided below to learn more!

Boat Canvas Repair Kit Other Tools Needed KAI Scissors
Also see our boat canvas material selectionhere.
92 Polyester Thread 8 oz. Available in Black and White 138 Polyester Thread 1 lb. Available in Black and White Solarfix Black and White
Stainless Steel Durable Eyelet Stainless Steel Durable Stud
Black Durable Eyelet Black Durable Stud

our Other EZ-Xtend Boat Zipper products:

Boat Zippers with EZ-Xtend Technology Boat Track EZ-Xtend Drip Shields EZ-Xtend Boat Track EZ-Xtend Drip Shields It is a registered trademark of C.S.Osborne Company, and it is a registered trademark of Hoover goods.Pres-n-snap is a registered trademark of Hoover products. Lift-The-Dot is a trademark owned by Dot Fasterners, and it is used under license. We would love for you to stop by Cover Girl Marine Canvas Upholstery and view some of our incredible work!

Pop Up Camper Repair

ZIPPERS FOR BOATS THAT EASILY EXTEND EZ-Xtend Boat Tracks and EZ-Xtend Drip Shields are two of the most popular products on the market. It is a registered trademark of C.S.Osborne Company, and it is a registered trademark of Hoover goods.Pres-n-snap is a registered trademark of Hoover products, and it is a registered trademark of Hoover products It is the trademark of Dot Fasterners to use the term “Lift-The-Dot.” We would love for you to stop by Cover Girl Marine Canvas Upholstery and view some of our fantastic work!

Repairs You Can Do Yourself

The majority of pop-up camper repair work may be completed by the camper owner, depending on his or her repair skills. Some repairs, such as replacing all of the canvas or repairing faults with the electrical or gas systems, should be left to a professional to complete. If the trailer was involved in an accident, it is recommended that structural repairs be performed by an expert.

However, this does not rule out the possibility of taking responsibility for your camper’s health. Take a look at how to do some of the little repairs you may complete at home on a daily basis.

Repair a Tear in the Canvas

Pop-up campers are often constructed of canvas, which can rip, develop holes, or rot when exposed to the weather for an extended period of time. It is not possible to simply patch a hole or rip closed. Because of this, you must repair it with another piece of canvas, or else the canvas’s waterproofing properties will be compromised. You want to get the canvas repaired as soon as possible so that the situation doesn’t become any worse. The following are the steps to restore the canvas:

  1. Because of their openness to the weather, pop-up campers are often constructed of canvas, which may rip, develop holes, and decay. It’s not enough to just patch a hole or rip closed. The waterproof characteristics of the canvas may be compromised if you do not repair it with another piece of canvas. To prevent the situation from becoming worse, you must get the canvas repaired as quickly as possible. The following are the procedures for repairing the canvas:

Waterproof The Camper

It is possible that the canvas of the pop up camper will need to be waterproofed at some point. You may apply a waterproof wax to the canvas or spray it with a fabric waterproofing spray to make it waterproof. Similarly, the seams throughout the length of your camper may require resealing with a high-quality sealer in order to prevent any moisture from getting into the gaps and causing mold and mildew to develop. If it appears like you will need to replace the sealant, be sure you first remove the old sealant and then proceed to replace it with fresh sealant, as described above.

Fix the Crank

In some cases, it may be necessary to waterproof the canvas of a pop-up camper. To waterproof the canvas, you may either rub it with a waterproof wax or spray it with a fabric waterproofing spray. A quality sealer may also be required to reseal the seams throughout the length of your camper to prevent any moisture from seeping into the gaps and causing mold and mildew to develop. Make sure you remove the old sealant first, and then proceed to replace it with fresh sealant if it appears that you may need to do so in the future.

  1. The first step is to lube the crankshaft and pulleys using a high-quality lubricant. If you want to loosen up your crank, don’t use a spray solvent like WD-40. Instead, use true lubricating grease, which may be found in spray bottles
  2. This will last longer. If your crank is still not operating, inspect the wires for breakage or slips off the track
  3. If necessary, replace the crank. Identify any fractures or breaks in the cable, and replace the damaged cable as necessary
  4. Some newer campers may have more intricate mechanics, for which you should seek expert assistance
  5. Older campers may have simpler mechanisms.

Repair the Screen

A certain amount of general wear and tear is to be expected in any car that you spend a significant amount of time in. In some cases, you may discover that your window screen has a small rip in it. If the tear is tiny enough, you can repair it by painting it with clear nail polish. If the rip is wider, you’ll need to look for a screen repair kit to provide a long-term remedy for the problem. In the event that you have a rip while on your expedition and don’t have the time or resources to purchase the appropriate supplies, weatherproofing tape can serve as a temporary solution.

Perform Tire Maintenance

Any car that you spend a significant amount of time in will suffer from general wear and tear. Your window screen may have a minor rip in it, which you will need to repair. If the rip is tiny enough, you can cover it with clear nail paint to make it disappear. You’ll need to look for a screen repair kit, though, if the rip is wider and you want a long-term solution. However, if a rip occurs during your expedition and you don’t have time to purchase the appropriate supplies, you may use weatherproofing tape as a temporary solution.

Replace Linoleum Flooring

If the linoleum in your pop up camper is lifting or otherwise in poor condition, you may easily replace it with new vinyl floor covering. Here are some simple measures to take to replace the present flooring in your recreational vehicle:

  1. Take out all of the old flooring and dispose of it properly. Vacuum and sweep the ground level, making certain that it is totally free of dust and dirt. Calculate the dimensions of your flooring and cut pieces of whichever sort of vinyl you’ve chosen to guarantee a precise fit. Install the vinyl tiles or wood slats and attach them in place with screws or nails

Take Care of Your Pop Up Camper Yourself

Unless you’re in the RV or camper business, the odds are good that you don’t know how to do repairs on your pop-up camper, or when something can be fixed at home rather than by a professional.

Fortunately, the majority of damage that occurs to campers can be repaired at home or on the road, and opting to do these easy repairs yourself may save you a significant amount of money while also extending the life of your camper. All rights retained by LoveToKnow Media, Inc. in the year 2022.

Leave a Comment

Your email address will not be published. Required fields are marked *