How To Repair Shock Cord Tent Poles

How to Replace Shock Cord in Tent Pole

There are various little components in a tent that might fail, but these do not need the purchase of a completely new unit. Tent pole shock cords are susceptible to failure, deterioration, and brittleness with time, and finally loss of their elastic qualities. Your tent pole may no longer operate properly if the shock cord is no longer functioning properly. You may believe that new tent poles are required. Purchasing new tent poles, on the other hand, may be quite expensive, and there is a lot more affordable option.

It is simple to replace the shock cord in your tent pole; all you need are a few simple components and a positive mindset.

We’ll also talk about why shock cords are vital, as well as some preventative actions you may do to avoid more harm.

If you know how to fix a broken tent pole in the field, a broken tent pole in the field does not have to be a cause for alarm.

What is a tent shock cord and why is it important?

Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.

Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.

What you need to replace the shock cord in a tent pole

Make sure you have all of the materials you’ll need before starting to work on your tent repair. A replacement shock cord can be purchased at your local camping store, and there are numerous retailers who sell shock cords online as well. You will require the following materials:

  • The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
  • Scissors or a sharp edge
  • Measuring tape
  • Sharpie or marker pen
  • A lighter or matches to melt the ends of the wires Tape for masking

How to replace a faulty shock cord in a tent pole

The time has come to get started on repairing your shelter now that you have all of the tools you need, as well as some new shock cord to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will notice that your tent pole will fall apart into its various sections once the cord has been severed.

  1. Because it’s likely that the pole sections in the middle are identical, the end pieces where the cord is tied are the most important parts to avoid getting mixed up in the process.
  2. Perhaps you’ll need to unscrew your grommet pegs and then untie the remaining cord before you can continue.
  3. 2.
  4. Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
  5. Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
  6. If you are unable to use your old cord as a guide, measure and mark the replacement cord to be approximately 8 inches shorter than the pole, or approximately 75% of its total length.
  7. You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.

Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.

Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.

Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.

When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.

When you’ve reached the desired length with the cord, tie a knot here to ensure that the peg is secure.

Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.

All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.

We’ve come to the end of our instructions on how to replace the shock cord inside a tent pole.

All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.

The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.

If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.

How to Repair a Shock Cord if it Breaks in the Field

The time has come to get started on repairing your shelter now that you have all of the tools you need, as well as some new shock cord to replace your old, faulty ones. Your tent will look like new if you follow our instructions. The first thing you should do if your shock cord is still intact is to split your tent pole in half and use scissors to cut the shock cord that is hidden inside. You will notice that your tent pole will fall apart into its various sections after the cord has been severed.

  1. Given that it’s likely that the pole sections in the middle are all identical, the end pieces where the cord is tied are the most important parts to avoid becoming confused with one another.
  2. Some grommet pegs may require unscrewing before the remaining cord may be untied.
  3. The length of the cord that will be used to replace the old, broken one must now be determined.
  4. If you want to know the entire stretched length of cord you’ll need, measure your pole from end to end.
  5. Don’t cut the rope until you’ve marked it with a marker pen the length you’ll need.
  6. If you are unable to use your previous cord as a reference, cut a new cord that is approximately 8 inches shorter than the pole, or around 75% of the overall length of the original cable.
  7. Due to the fact that you’ll be threading the cord through the tent poles, you’ll need to cut the cord a little longer than the tent poles.

Finally, start threading your tent pole by taking the longer end and threading it through each segment of the pole.

Make certain that the cords are threaded in the correct direction, from male to female, or else they will not fit together when you’re finished sewing.

Build the tent pole so that all of the components are joined together, just like you would while pitching a tent.

While the free end of the new shock cord should be passed through the peg at this point, the cord should not be fastened on at this time.

Continue to apply strain to the shock cord until you see the mark you produced previously.

5.

Use a lighter or a box of matches to singe the end of the cord so that it does not fray or unravel.

With everything tucked away and reassembled, there should be no evidence of the shock cord outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable within a tent pole.

The wear and tear on all camping equipment is inevitable, although it is rarely essential to replace it.

This is an excellent strategy to utilize if you’re at home and need to do some repairs, but what happens if your shock cord breaks while you’re on a camping trip?

If you don’t have an extra length of tent pole shock cord on available, keep reading to learn about potential alternatives to this procedure.

Using string as a temporary replacement for a broken shock cord

If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can get a new replacement cord. Although this will not have the same elastic properties as proper shock cord, it can be used as a temporary replacement until you can make more substantial repairs. Keep this in mind when using this. All you need to complete this DIY fix is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a limited number of materials.

  • Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
  • Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
  • This will make it much easier to thread the string back through the tent.
  • Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
  • Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
  • Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.
  • Any mistakes can be corrected by untying the end at a peg and making any necessary adjustments.

How to repair a broken tent pole

The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a broken tent pole as well as replacing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.

  1. Purchasing a repair sleeve is an inexpensive option if your tent does not come equipped with one; you never know when you might require one.
  2. If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
  3. If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
  4. Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.

Using duct tape, attach a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did before. Duct tape may be used to cover the whole surface; just make sure your repair is secure before proceeding.

Preventing damage to your tent poles in the future

If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose dirt, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.

When building your tent and connecting the tent poles, start with the central segment and work your way out from there.

This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.

If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.

Final Verdict:

It is occasionally required to replace the shock cord in your tent pole, but it does not have to be a difficult process. It is possible to save a large amount of money by making minor repairs and replacements to your camping equipment over time, and it is also considerably healthier for the environment. Learning how to execute these little repairs is simple, and more importantly, it will make you a more experienced camper. As an added bonus, watch this video for some further tent pole repair advice!

See also:  What Is The Main Tent Of A Circus Called

How to Replace a Tent Pole Shock Cord

The elastic shock cord on your tent poles has deteriorated and has become brittle, making it no longer flexible. Given that new poles can cost up to $100 or more, why not simply replace the cord, which costs less than ten percent of the price of new poles? It’s been years since I’ve used my North Face Rock 22 two-person tent (which has two identical poles), and the elastic cord inside the poles has become brittle and no longer retains its flexibility. I had purchased the tent brand new for around $200, and replacement poles were going to cost an additional $150!

I just needed 30 minutes and a pint of beer to get my tent poles back to their original condition!

You’ll need at least the whole length of all of your poles combined to complete the task.

My poles were 152 inches apiece, and I purchased a total of 30 feet (or 360″ of cord). a pair of scissors or a knife Sharpie or Marker for Measuring Tape Matches or a lighter are recommended. 3rd Grade Math Capabilities

Step 1: Cut the Cord and Remove the Grommet Pegs

Take a deep breath in and out. Pulling two parts of the pole apart and cutting the rope will do this. This will cause the pole to divide into its distinct parts (Mine has 8 sections per pole, and only the two end sections are different, so I made sure to keep those separate). Remove the peg from the pole end and you should be able to see the standing end of the cord, which has been knotted and connected to the peg. Because my pegs were threaded, I had to detach them from the pole sections in order to use them.

Step 2: Measure Your Pole(s)

Following that, you’ll want to take measurements of your poles so that you can determine how long your rope should be. Because my tent has two poles that are exactly the same length, I only had to measure once. If you have multiple poles of varying lengths, you will need to repeat this step for each pole in your set. Measure the length of your pole from end to end; this will be the length of your rope when it is fully stretched. My experiments with the elasticity of the cable led me to the conclusion that for every foot of relaxed cord, I would receive 1′-4 of length “because of a stretched chord To get the final length (the length of the pole, hence the ultimate stretched length), we must multiply it by 75% of the original length.

Take the length of your pole in inches and multiply it by 0.75.

My poles are 152 inches in length, hence my measurement is as follows:152 inches * 0.75 inches = 114 inches” This is the spot where I put my relaxed chord marker.

It is quite difficult to feed a 114″ cable into a 152″ pole because of the length difference.

Step 3: Thread Your Peg and Knot the Cord

Feed the standing end of the cord (the end that is marked with a ‘zero’ on the tape measure) through the hole in the grommet peg and secure it with a rubber band. Draw the thread through a basic binding knot about 2 inches from the end and tighten it. Your peg should now be in the middle of the knot and the long end of the rope, as seen below. In order to avoid tripping, feed the cord through the first part of pole and continue until all portions are attached to the cord. Check to see that the pole portions are aligned appropriately so that they will fit together as intended before continuing (male end toward female end for each joint).

The long end of the cord should be stretched so that it reaches the mark you created earlier while the pole pieces are joined in the manner in which you would build the tent.

Make a basic binding knot and tighten it around the mark. In this stage, the pole should be beginning to take form. The pole parts should be linked, the pegs should be in place (but not inserted), and the cable should be stretched to its maximum length.

Step 4: Cut/Singe the Cord and Insert the Pegs

Remove the cable from the machine, leaving around 2 inches of standing end. Make a singing sound with the lighter or matches at the end of each string (on both ends of the pole). Fold the cord over upon itself and put the standing end of the cord into the pole to complete the loop. Incorporate the knot into the pole. Insert the peg into the pole with the threading needle. Each pole should be treated in the same way.

Be the First to Share

Determine the diameter of the cord that has to be replaced. When it comes to low-cost tents, this will typically be around 2mm in diameter, which is not very strong or long-lasting. Depending on how large the opening diameter is of the pole, you may be able to utilize a thicker diameter than you originally planned. I increased the diameter of the cable on my tent poles from the standard 2mm to 3mm. The cord can be purchased on eBay for a reasonable price. I live in the United Kingdom and purchased 10 meters for approximately £3.

In order to set up a two-person dome type tent with two tent poles, you’ll need at least ten meters of space.

In an updated version of this post, I measured the original cable and discovered that it was half the length of the poles after they were completed.

Step 2: Find Your Threader

A threader, which you will need to obtain, will be required to feed the cord through. An excellent metal threader was discovered inside an old windscreen wiper, which I was able to salvage. Consequently, when it is time to replace your windshield wipers, save them or borrow some from your neighborhood auto repair shop. The wiper blade assembly has two strips of metal that span the length of the wiper blade. You must remove these strips of metal from the wiper blade assembly. The best wiper blades are those from a saloon car or a van because they have the longest blades available.

Please keep in mind that my photo displays a windscreen wiper, however it is too short.

Metal inserts are uncommon to be found in the lower-priced wiper blades.

Step 3: Join Threader to New Cord

It is now necessary to connect the threader to the new cable. This is accomplished by joining the threader and cable together using a butt joint and then fastening the junction with a very little quantity of adhesive tape.

In this photo, I used one revolution of double-sided sticky tape. Use only a little amount of tape, as too much will cause the threader to drag and cause it to stick to the inside wall of the tent pole.

Step 4: Remove Old Elastic Cord and Re-thread New Cord

To complete the task, you must attach the threader to the new cord. When the threader and cord are joined together, a very little quantity of adhesive tape is used to hold them in place until the threader is finished. In this photograph, I used one revolution of adhesive tape. The use of too much tape will slow down the threader’s movement and cause it become tangled in the inside wall of its tent pole.

Step 5: Tension Cord and Tie Off the Ends

Trial and error is required to achieve the desired tension, so after threading the entire pole, experiment with your cord tension. The tension must be light enough to allow the poles to be pulled apart, but firm enough to keep them together when threaded through the tent’s opening. The figure of eight knot is my preferred method of tying off the ends because it is a bigger knot that is also easy to alter. A more substantial knot at the end will last longer. You can then cut the cord after the tension has been reached to your satisfaction.

Step 6: Finished – Store Threader for Next Repair

You should have completed the repair of the tent poles by now. Remember to keep your threader handy for when you need to repair your tent! I hope you have found this information beneficial. Thank you for taking the time to watch!

Be the First to Share

Tent poles are the skeleton of your outdoor shelter, giving support to hold the tent erect. Based on 58 reviews, the average rating is 3.7 out of 5 stars. If a pole breaks, your tent may wobble, flap, or fully collapse, therefore it’s a good idea to be prepared with the essential materials and know-how to repair a broken pole before you go camping. In this article, we’ll show you how to do the following:

  • While in the field, learn how to use a repair sleeve or an old tent stake to hold a broken tent pole together until it can be repaired at home. Learn how to replace the flexible shockcord inside your tent pole if it breaks or wears out and how to make an at-home repair.

Repairs by professionals: If you require professional assistance, many REI stores can perform basic repairs. Alternatively, TentPole Technologies, the nation’s best pole repair service, is a fantastic alternative. REI Repair Services is a division of REI.

Splinting a Broken Tent Pole

The damage done to your tent pole by a violent gust of wind or stepping on it is irreversible. A kinked, split, or shattered pole requires rapid treatment when out camping (when you get home, you can look into having the pole replaced or professionally repaired.) There are two alternatives available to you:

  • Use a pole repair sleeve to fix the problem. Make a splint out of a tent stake.

Using a Pole Repair Sleeve

A pole repair sleeve is the quickest and most convenient method of repairing a damaged pole. This little tube, which is also known as a splint, is frequently included with your tent. If you don’t already have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not move about too much. A repair sleeve is an easy way to patch a broken tent pole. Here’s how:

  1. Stack the broken pole components in a straight line
  2. It is possible to straighten out the curvature in the pole if it is bent but not completely broken. Adjusting the sleeve over the pole end until it’s perfectly centered over the break or kink can necessitate the use of pliers or a rock to bend spread sections so that the sleeve can glide over them
  3. Make two or three wraps around each end of the sleeve/pole, using duct tape or whatever heavy-duty tape you happen to have on hand. It may be necessary to splint the portions of a broken pole together where one pole end fits into the next pole end
  4. However, this will prevent the poles from folding neatly when you pull the tent down.

Using a Tent Stake as a Splint

If you’ve misplaced or forgotten your pole repair sleeve, you can make a rudimentary splint out of a tent stake as follows:

  1. Stack the broken pole components in a straight line
  2. The curve should be straightened out if the pole is bent but not completely broken. Align the stake such that it is centered close to the breach in the ground
  3. Wrap duct tape around each end of the stake/pole many times, or use whatever heavy-duty tape you have on hand.

How to Replace Tent-Pole Shockcord

After a period of time, the flexible shockcord that is included within your tent poles may become abraded and snap, or it may just lose its elasticity completely. Despite the fact that the shockcord snaps while you’re out in the field, you may still utilize the pole by carefully assembling each of its component pieces.

But when you arrive home, you’ll want to replace the shockcord since it simplifies the assembly process and prevents you from losing a pole segment during transport. Fortunately, the procedure of changing it is uncomplicated. Here’s everything you’ll need to get started:

  • A marker with a permanent ink supply
  • Masking tape (optional)
  • A pair of scissors Scissors
  • Pliers with a locking mechanism (optional)
  • Shockcord with a 1/8-inch diameter (about the length of your tent pole)
  • New 1/8-inch diameter shockcord

The following is the procedure for replacing the shockcord:

  1. Begin by placing the tent pole out straight on the ground. Sections can be labeled with a permanent marker (masking tape can be used if you don’t want to write directly on the pole) to prevent them from becoming mixed up. Remove the old cable by snipping it, and then take the elastic out of the pole end. Maintain the same sequence and alignment of all of the pole parts for the duration of your job
  2. It is common for tent poles to have a little metal piece attached at either end where the string is fastened
  3. Keep an eye out for these pieces and make sure they are not lost. Using your old shockcord, untangle the ends and place them next to your new shockcord. the length of the new piece of shockcord should be trimmed to match the length of the original The replacement part should be approximately 8 inches shorter than the previous section if the old shockcord has become stretched out and no longer has its elastic properties. Tighten one end of the shockcord and pass the other end through all of the pole sections until the last one
  4. Make a temporary knot in the shockcord to prevent it from slipping back into the second-to-last pole section
  5. Alternatively, you can use a pair of locking pliers to hold the cord in place. Feed the remaining shockcord through the final section of the pole and tie the end together. Return to the beginning and untie (or unclamp) the rope that connects the final two pole parts. Check to make sure that all of the pole components are securely fastened to the completely completed pole. If the shockcord is still too slack, untie one end and pull it out 6 inches at a time until the poles are securely fastened together when the shockcord is tightened. It is important not to over-shorten the rope. Using pliers, remove the parts of the pole and fold it up starting at the center position
See also:  Where To Sleep In Tent On Smokky Mountains

Related Articles

  • Starting with the tent pole, make sure it is straight and parallel to the ground. Sections can be labeled with a permanent marker (masking tape can be used if you don’t want to write directly on the pole) to prevent them from being mixed up. Take a pair of scissors to the old cable, and then carefully take the elastic out of the pole end
  • Watch out for maintaining the same sequence and orientation for all of the pole parts while you’re working. A little metal item at either end of some tent poles, which serves as a tie-down point, should be kept an eye out for and avoided at all costs. Using your old shockcord, untangle the ends and place them next to your new shockcord
  • The new portion of shockcord should be cut to the same length as the old section The replacement part should be approximately 8 inches shorter than the previous section if the old shockcord has become stretched out and no longer is elastic. Make a knot in one end of the shockcord and pass the other end through all of the pole sections until the last one
  • Stretch the shockcord to increase its length, and then tie a temporary knot to prevent it from slipping back into the second-to-last pole piece
  • Alternatively, you may use a set of locking pliers to hold the cord in place while you work. Feed the remainder of the shockcord through the final part of the pole and tie the end together. Repaint the area where the final two pole parts were tied together (or unclamped). Ensure that all of the pole pieces are securely secured in the completely built pole by performing a final inspection. Remove 6 inches of shockcord at a time, untying one end at a time, until the poles are securely held together when the shockcord is tied in place. Keep the cable from becoming too short. Remove the parts off the pole and begin folding it up from the center point
  • This should take around 15 minutes.

Contributing Experts

Jon Almquist works as a product manager for tents at the REI Co-op headquarters in Kent, Washington.

Laura Evenson

Currently, Laura Evenson works as a sales lead in the camp and climb departments at the REI Conshohocken location in Pennsylvania. Laura’s 2013 Appalachian Trail thru-hike included 27 consecutive days of rain, demonstrating her tenacity as an adventurer.

Chris Pottinger

Chris Pottinger works at REI Co-op in Kent, Washington, as a senior tent designer.

Lindsey Stone

Currently based in Seattle, Lindsey Stone works as the operations director for Rainy Pass Repair Inc. Prior to that, she worked as a professional sewing technician for a total of 12 years. Her family, which includes her husband, kid, and dog, likes hiking, camping, and canoeing together.

How to replace shock cord in tent poles

Have you ever experienced that shaky, jittery feeling in your stomach? I’m talking about the one when your tent poles don’t instinctively want to snap together, but instead stand at attention like slender, lightweight soldiers on display. Even if you’ve owned your tent for a long time and taken it on a number of trips, sooner or later you’ll need to learn how to replace shock cord in tent poles. Here is a video tutorial showing you how to do it step by step. The good news is that changing the shock cable in your tent poles is not difficult to accomplish.

Listed below is the procedure I used to replace the shock cable in my Macpac Sololighttent.

You will need:

  • Repair or replacement shock cord (check with your local hardware store, maritime store, eBay/Amazon, or tent maker for options)
  • Scissors
  • Sticky tape (gaffer tape, masking tape, duct tape)
  • Sharpie

In addition to losing its stretch, this ancient shock cable featured substantial regions of damage where the cord looked to have been welded to itself, which was discovered upon investigation.

Step 1: Remove the old shock cord

The method for gaining access to and removing the cable varies depending on the type of tent. Each end of mine has a straightforward screw top fitting. As an alternative, you can simply cut the cord and slide it out from underneath.

Step 2: Keep the poles in order and number them

Those clever people who design our tents may have specified a certain order in which the poles must be installed in order to guarantee that the tent maintains its proper shape. Consequently, number your poles so that you can quickly put them back together again. much as you would while cheating on a crossword problem.

Step 3: Tie a knot in one end and secure

Taking note of how the maker fastened the final knot may be beneficial so that you may replicate it later. Remove any surplus material from underneath the knot.

Step 4: Start feeding through your cord

Make your way around to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through until you reach the lug and secure it in place.

Step 5: Continue threading poles in order

Move to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through to the lug and fastening it securely in place with your fingers.

Step 6: Apply tension and hold in place

As you near the end of the rope, you will need to apply some stress to the elastic shock cord in order for it to make it all the way to the other side.

While threading the final pole, you’ll need to secure it with some tape to keep it from moving about.

Step 7: Test the tension

Test the tension in your tent poles by bending them into the approximate form of your tent frame before tying everything off at the end.

Step 8: Tie a knot in the end and secure

Secure the end lug with a knot at the end of your cording project. Insert the knot and lug into the end of the pole and tighten them together. Posted on September 13, 2019 in How To by admin

How do I repair the shock cord at the center of my pole?

This page was last modified on Tuesday, March 9, 2021 at 10:26 a.m. If you have a shock cord that has become stretched out, gone slack, snapped, or is just worn out and in need of replacement, you have come to the proper spot to get it replaced. This is really a fix that can be completed rather fast and simply at home with little tools. Quest Outfitters carries shock cord, which can be obtained at most hardware stores, outdoor retailers such as REI and Moosejaw, and sporting goods stores.

DIY Shock Cord Replacement

You will need 1/8″ thick shock cord that is around 1-2 feet longer than the length of the complete pole for each pole (for example, if you have a 10ft pole, obtain roughly 12ft; others think a 34% ratio may be preferable.).

  1. The shock cord will be wound in a knot once the end tip has been removed (either on a washer or on the end tip of the pole). Cut the knot and you’ll be able to remove the shock cord with ease. The most essential thing to remember is to remove the pieces of each pole in the same sequence that you removed them. After you have removed the old shock wire, you will be ready to thread the new shock cable on each pole. Remember to string them back together in the same sequence. Gently push the shock cord through the entire length of the pole, then tie it off at one end (either with a simple knot or with a loop attached to the pole tip)
  2. Then, to tension the shock cord, pull out about 25% of the total length of the pole in slack (for a 10ft pole, pull out 2-3ft), and tie it off at the pole end. After that, you may check the tension and make any required adjustments
  3. The pole parts should softly seat themselves. Keep in mind that this is not an exact science, so use your best judgment and common sense while making decisions. Remove any extra shock cable after that, and you’re finished

Here’s a link to a fantastic tutorial from REI that goes over the process of fixing tent poles and includes a part on how to restring shock cord at the base of the pole: Fixing a Tent Pole (with Pictures) Did you find it to be of assistance? Yes NoFeedback is not required.

Amazon.com: AceCamp 1/8 Inch Shock Cord Pole Repair, Replacement Bungee Strap Rope for Worn & Old Tents, Emergency Stretch Elastic Cord, Moisture UV Weather & Abrasion Resistant, 65 Feet : Tools & Home Improvement

Verified PurchaseReviewed in the United States on July 6, 2020Verified PurchaseWorked just as it should have I worked my way through the three poles that needed fresh cable. My first step was to lay out the poles and draw the old cord out a little bit before securing it and cutting the knot. I then used a little piece of scotch tape to attach the new cord to the old one, coiled it up tightly, and pulled the new cord through with the old cord. My cherished, leaky North Face Assault 2 from 2016 was in need of repair, and it only took a few minutes per pole.Reviewed in the United States on January 28, 2022Verified Purchase So, my beloved, leaky North Face Assault 2 from 2016 was in need of repair.

  1. I would have preferred it to be a fraction of an inch bigger in diameter, but I’m not going to argue.
  2. Although it is a natural instinct, doing so will cause you to be frustrated for hours at a time.
  3. Bring the old and new elastic through the poles (mine have seven pieces, so this is a significant undertaking).
  4. Most of the time, it’s a pretty calm place to work.
  5. Verified Purchase My tent has been brought back from the dead by Tom Simmons of Grinnell, Iowa.Reviewed in the United States on March 27, 2018Verified Purchase The poles remain connected in the manner in which they could be again.
  6. If you get stuck, look for a video on the internet.
  7. After reaching the final two poles, stretch the cord (but not too tightly) and tie a temporary loop to hold it taut until you reach the next pole.

I received this item quickly.I have someone interested in purchasing my tent and wanted to make sure everything was in good working order.I am very pleased that I was able to replace the old shock cord.The price is reasonable, so I would recommend this item.Reviewed in the United States on January 1, 2021Verified Purchase I was able to re-cord my super sized 6 person dome tent with this.Reviewed in the United States on January 1, 2021Verified Purchase I had enough to complete both the huge shock poles and the rain fly poles in one go.

I have a modest amount of length remaining.

To cut, I used an electric hot knife.

The cord snaps onto one end of the pole portion, causing the knot end to be knocked out of the way. In order to provide nice tension without overstretching the cord, I pulled out about a third of its total length.

Top reviews from other countries

5.0 stars out of 5 for this product It’s a long stretch. The article was reviewed in the United Kingdom on August 15, 2018. Purchase that has been verified It appears to be an appropriate length for the money and appears to be appropriate for the task. 4.0 stars out of 5 for this product Four out of five stars On September 7, 2016, a review was published in the United Kingdom. Purchase that has been verified The ideal back-up. Installation in poles is simple, and the resulting structure is sturdy.

  1. On June 26, 2017, a review was conducted in Mexico.
  2. You never know when you might need anything and you don’t want to be caught without it.
  3. On July 27, 2021, a review was conducted in Germany.
  4. I would recommend it highly.
  5. Purchase that has been verified The product is good, but the packaging is excessive, and it would have been better if it had been packaged differently.
See also:  How Many Round Tables Fit In A 20X30 Tent

How To: Replacing the cord in your tent poles

17th of July, 2020 Tension is applied to tent poles by the use of shock cock, an elastic string that aids in the snapping back together and maintaining the form of the tent poles. It is possible for the elastic in the shock cord to degrade with time, causing the cord to sag and, eventually, making your poles very difficult to use and practically impossible to use. A replacement tent pole set may be rather expensive, so if your poles are still in good condition, it is significantly more cost effective to simply change the cable.

Because these tent poles are from my Sierra Lightning II FL, and because no two tents are exactly alike in terms of size, the quantity of shock cord you’ll need may vary depending on your tent.

When determining the quantity of cord to purchase, I find it better to just purchase the same amount as your pole dimensions to allow for some margin of error.

Shock cord is available at most respectable camping stores as well as on the internet.

What you’ll need:

  • July 17, 2020 is the day on which the event will take place. When the tent poles are stretched, they snap back together and maintain their form. Shock cock is used to hold them in place. It is possible for the elastic in the shock cord to degrade with time, causing it to droop. Eventually, this will cause your poles to become extremely difficult to use and practically impossible to use altogether. Replacement tent pole sets may be expensive, so if your poles are in good condition, it is significantly more cost effective to change the cable instead. Before we get started, there are a couple of things to consider. First and foremost, the tent poles are from my Sierra Lightning II FL, and unless you have the exact same tent as I have, the quantity of shock cable you’ll use may vary depending on your setup. In my tent, each pole is joined by a swivel, and the entire structure is made of canvas. In order to allow for error when estimating the quantity of cable to use, I recommend purchasing the same amount as the pole dimensions. You will, however, be tensioning the cord at a length that is approximately two sections less than the actual length of the poles when you tension the cable. Shock cord is available at most reputable camping stores as well as on the internet for a little cost.

* For tent poles with an inverted stopper in the ferrule, rather of a pull-out or screw-out style stopper. You can also watch a video on how to change your tent pole cordhere on YouTube to see how to do it yourself. Tent poles are being unfolded.

Step 1

Prepare your tent poles by laying them out.

Because you’ll be unthreading them, you’ll want to do this in a place where you have lots of space to keep them organized.

Step 2

The end stop at the end of your tent pole should be removed. Removal of the end stopper* If your tent poles are the older design with a stopper or washer in the ferrule, you’ll need to take the knot out of the stopper with tweezers and cut or untie it to allow the new rope to pass through and out of the way. When you reach to the other end, you’ll have to repeat the process in the opposite direction. The difference between poles with a pull-out end stopper and poles with a washer is seen in the diagram to the right.

Step 3

Untie the string or cut it at the end stop and set the end stop on the ground. As you begin to remove the old shock cord, make sure to arrange your tent poles in the same position as you did previously. Taking the cable out

Step 4

Obtain your new piece of shock cable at this time. I’ve pre-measured my and indicated the place where I want it tensioned to, but I’m not going to cut it yet since I find it simpler to tie and cut it once it’s already been tied. Begin with the first piece of pole and pull your shock cord all the way through to the stop at the end. Then tie a knot around the end stop to keep it in place. INVERTED STOPPER: If you’re working with an inverted stopper, you’ll want to make sure your wire is prepared.

When you reach to the end, tie a strong knot large enough to prevent the shock cord from passing through the hole again.

Feeding the wire through the washer is a simple process.

Step 5

Now that the end has been attached, draw the shock cord through the remaining sections of poles, being sure to retain them in the same sequence as they were originally put out.

Step 6

Once you reach the end, tighten the cord until you reach the mark on it, then secure it to the end stop, being careful to maintain the proper amount of tension in the cable. I like to check the tension one more time before cutting the line. You should tension the cord just enough to bring the poles together, but not so much that the shock cord becomes over-stressed when the poles are folded.INVERTED STOPPER: Before you reach the end, you’ll need to pause before the last section of pole.INVERTED STOPPER: You’ll need to pause before the last section of pole.

Now, re-grab your wire and push it through the final length of pole, starting at the other end and working your way toward the end stopper.

Return to the other end of the stopper and undo the knot on your second-to-last piece of pole section and fasten it to the wire.

Pull the wire through until the cord is completely through the hole in the stopper. Adjust the tension as needed, then finish with a knot that is large enough to catch on the hole.

Step 7

When you’re satisfied with the tension, cut the cord neatly and tuck the end back inside the pole sleeve with the end stop, securing the end stop with a screwdriver. The shock cord may require assistance in this area since it is difficult to cut and is much simpler to cut when someone else is tensioning it for you.

How to Fix your Pole Set

Ever returned to camp after a long day on the trail to discover your tent overturned and your pole set a complete mess of shock cord and poles? If so, you’re not alone. Hopefully, the response is negative. However, occasionally a storm or a stray wind gust might have a negative impact on your tiny home away from home. Fortunately, our staff here at NEMO has prepared for the worst, and your tent comes with a pole splint that can be found within the pole bag. Here’s what you’ll need to accomplish in order to go through the rest of your journey: 1.

  1. Locate the pole splint and the broken pole segment in your pole set by following the arrows. The pole splint should be pushed up the poles until it is covering the fractured pole piece. Make use of duct tape or repair tape to keep the pole splint firmly attached to the pole set. You can use a pole set until you’re able to return home and do a more thorough repair. Watch this video for a quick tutorial on how to use it.

At-Home Repair

Once you have returned home, please contact our customer service department. Because pole segments are removable, you won’t have to replace the entire pole set if one segment breaks. If you have any questions, please contact us at 800-997-9301, or fill out our Spare Parts Obtain Form to request a pole section. In either case, they’ll be pleased to assist you in restoring your pole set to full functionality in preparation for your next expedition. Although disassembling a pole set might seem scary if you’ve never done it before, it should be a simple and quick operation as long as you follow the steps in the instructions carefully and thoroughly.

This chart may also be used to keep track of your progress once you have received the replacement pole section and are ready to begin the repair.

Once you’ve received the new pole segment, follow the step-by-step process below for replacing it in your pole set:

1. Remove the ball cap from the end of the pole that is closest to the damaged segment. After that, detach the ball cap from the shock cable with a screwdriver. Remove the ball cap from the pole by unscrewing it and pulling it away from the shock cord. 2: Untie the shock cord loop so that the shock cord can be easily threaded through the poles. One of the most common NEMO tent components, this three-pronged hub links the shock cable to the hub through a little black clip that can be taken out of the middle of the hub.

3.

You may put a number on a piece of paper (or directly on the pole itself in marker) and name the poles as they come off the shock cord with that number as they come off the cable.

4.

5. Maintain a firm grip on the shock cord, as it has a reputation for sliding through your fingers! 6. Once you’ve threaded the rope through the last pole and connected it to the ball cap, tie a knot at the end. 7. Replace the cap on the end pole using a screwdriver.

Special Instructions: Hubs

A broken pole segment may necessitate the removal of a shock cord from a central hub; in this case, the following method is recommended for restoring the hub to working order.This three-pronged hub is found in many NEMO tents and connects the shock cord to the hub using a small black clip that can be pulled out of the center of the hub. Three-pronged hub: The Dagger, Aurora, Hornet, Hornet Elite, Firefly, and Dragonfly are all equipped with this hub, as are the Hornet and Aurora. One portion, the ridge pole of the tent, is joined to the other half by a little black clip, which is used to tie the shock cord to the hub of the tent.

The easiest way to remove this black clip is to:

1. To reach the shock cord of your pole set, use a sharp blade to go under the lip of the black hub covering and through the opening. It should easily pop out of the hub; we recommend removing both sides at the same time. With care, insert a blade between a lip on the hub covering and lift to release the cover. 2. Carefully pull the shock cable away from the black clip, allowing it to completely detach from the hub. This will assist in loosening the clip just enough to allow it to be removed.

  • In order to remove this clip, we recommend pushing it out via one side of the center hub aperture with a pen; do not hesitate to apply pressure because the clip is quite tough.
  • After that, you should be able to work it out far enough to be able to grip the other end with your fingers.
  • After you’ve finished repairing your pole set, thread a loop of shock wire through the hub leg until it pokes out of the centre of the hub.
  • 6.
  • 7.
  • To make a loop, feed the shock cable through the hub, then attach the black clip to the shock cord and pull the clip back into position in the hub to complete the loop.

Loose Shock cord? No problem!

Over time, shock cord’s elasticity might deteriorate as a result of its use. In the event that you observe fraying, loss of elasticity, or that the poles do not fit together correctly, it is critical that you replace the shock cord in your pole set. Shock cord may be found at most sporting goods stores and on the internet. You can also get in touch with us personally if you require shock cords. Following the installation of your new shock cable, you’ll want to disassemble your pole set according to the instructions provided above.

Do you have a question?

Leave a Comment

Your email address will not be published. Required fields are marked *