How To Fix Tent Pole Cord

How to Replace a Tent Pole Shock Cord

The elastic shock cord on your tent poles has deteriorated and has become brittle, making it no longer flexible. Given that new poles can cost up to $100 or more, why not simply replace the cord, which costs less than ten percent of the price of new poles? It’s been years since I’ve used my North Face Rock 22 two-person tent (which has two identical poles), and the elastic cord within the poles has become brittle and no longer retains its flexibility. I had purchased the tent brand new for around $200, and replacement poles were going to cost an additional $150!

I just needed 30 minutes and a pint of beer to get my tent poles back to their original condition!

You’ll need at least the whole length of all of your poles combined to complete the task.

Step 1: Cut the Cord and Remove the Grommet Pegs

Take a deep breath in and out. Pulling two parts of the pole apart and cutting the rope will do this. This will cause the pole to divide into its distinct parts (Mine has 8 sections per pole, and only the two end sections are different, so I made sure to keep those separate). Remove the peg from the pole end and you should be able to see the standing end of the cord, which has been knotted and linked to the peg. Because my pegs were threaded, I had to detach them from the pole sections in order to use them.

Step 2: Measure Your Pole(s)

Following that, you’ll want to take measurements of your poles so that you can determine how long your rope should be. Because my tent has two poles that are exactly the same length, I only had to measure once. If you have many poles of varying lengths, you will need to repeat this step for each pole in your set. Measure the length of your pole from end to end; this will be the length of your rope when it is fully stretched. My experiments with the elasticity of the cable led me to the conclusion that for every foot of relaxed cord, I would receive 1′-4 of length “because of a stretched chord To get the final length (the length of the pole, hence the ultimate stretched length), we must multiply it by 75% of the original length.

Take the length of your pole in inches and multiply it by 0.75.

My poles are 152 inches in length, hence my measurement is as follows:152 inches * 0.75 inches = 114 inches” This is the spot where I put my relaxed chord marker.

Please keep in mind that you should not cut the cord just yet! It is quite difficult to feed a 114″ cable into a 152″ pole because of the length difference. Inquire as to how I know this.

Step 3: Thread Your Peg and Knot the Cord

Feed the standing end of the cable (the end that is marked with a ‘zero’ on the tape measure) through the hole in the grommet peg and secure it with a rubber band. Draw the thread through a basic binding knot about 2 inches from the end and tighten it. Your peg should now be in the middle of the knot and the long end of the rope, as seen below. In order to avoid tripping, feed the cord through the first part of pole and continue until all portions are attached to the cord. Check to see that the pole portions are aligned appropriately so that they will fit together as intended before continuing (male end toward female end for each joint).

The long end of the cord should be stretched so that it reaches the mark you created earlier while the pole pieces are joined in the manner in which you would build the tent.

In this stage, the pole should be beginning to take form.

Step 4: Cut/Singe the Cord and Insert the Pegs

Remove the cable from the machine, leaving around 2 inches of standing end. Make a singing sound with the lighter or matches at the end of each string (on both ends of the pole). Fold the cord over upon itself and put the standing end of the cord into the pole to complete the loop. Incorporate the knot into the pole. Insert the peg into the pole with the threading needle. Each pole should be treated in the same way.

Be the First to Share

There have been 58 reviews with an average rating of 3.7 stars out of 5 stars for this product. Tightly woven tent poles serve as the skeleton of your outdoor shelter, giving support and structure to keep the tent standing. If a pole breaks, your tent may wobble, flap, or fully collapse, therefore it’s a good idea to be prepared with the essential materials and know-how to repair a broken pole before you go camping. In this tutorial, we’ll show you how to do the following:

  • While in the field, learn how to use a repair sleeve or an old tent stake to hold a broken tent pole together until it can be repaired at home. Learn how to replace the flexible shockcord inside your tent pole if it breaks or wears out and how to make an at-home repair.

Repairs by professionals: If you require expert assistance, many REI locations can do simple repairs. Alternatively, TentPole Technologies, the nation’s best pole repair service, is a fantastic alternative. REI Repair Services is a division of REI.

Splinting a Broken Tent Pole

The damage done to your tent pole by a violent gust of wind or stepping on it is irreversible. A kinked, split, or shattered pole requires rapid treatment when out camping (when you get home, you can look into having the pole replaced or professionally repaired.) There are two alternatives available to you:

  • Use a pole repair sleeve to fix the problem. Make a splint out of a tent stake.

Using a Pole Repair Sleeve

A pole repair sleeve is the quickest and most convenient method of repairing a damaged pole. This little tube, which is also known as a splint, is frequently included with your tent.

If you don’t already have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not move about too much. A repair sleeve is an easy way to patch a broken tent pole. Here’s how:

  1. Stack the broken pole components in a straight line
  2. It is possible to straighten out the curvature in the pole if it is bent but not completely broken. Adjusting the sleeve over the pole end until it’s perfectly centered over the break or kink can necessitate the use of pliers or a rock to bend spread sections so that the sleeve can glide over them
  3. Make two or three wraps around each end of the sleeve/pole, using duct tape or whatever heavy-duty tape you happen to have on hand. It may be necessary to splint the portions of a broken pole together where one pole end fits into the next pole end
  4. However, this will prevent the poles from folding neatly when you pull the tent down.

Using a Tent Stake as a Splint

If you’ve misplaced or forgotten your pole repair sleeve, you may make a rudimentary splint out of a tent stake as follows:

  1. Stack the broken pole components in a straight line
  2. The curve should be straightened out if the pole is bent but not completely broken. Align the stake such that it is centered close to the breach in the ground
  3. Wrap duct tape around each end of the stake/pole many times, or use whatever heavy-duty tape you have on hand.

How to Replace Tent-Pole Shockcord

After a period of time, the flexible shockcord that is included within your tent poles may become abraded and snap, or it may just lose its elasticity completely. Despite the fact that the shockcord snaps while you’re out in the field, you may still utilize the pole by carefully assembling each of its component pieces. But when you arrive home, you’ll want to replace the shockcord since it simplifies the assembly process and prevents you from losing a pole segment during transport. Fortunately, the procedure of changing it is uncomplicated.

  • A permanent marker
  • Masking tape (optional)
  • Scissors
  • Locking pliers (optional)
  • A new 1/8-inch-diameter shockcord (about the length of your tent pole)
  • A permanent marker
  • Locking pliers (optional).

The following is the procedure for replacing the shockcord:

  1. Begin by placing the tent pole out straight on the ground. Sections can be labeled with a permanent marker (masking tape can be used if you don’t want to write directly on the pole) to prevent them from becoming mixed up. Remove the old cable by snipping it, and then take the elastic out of the pole end. Maintain the same sequence and alignment of all of the pole parts for the duration of your job
  2. It is common for tent poles to have a little metal piece attached at either end where the string is fastened
  3. Keep an eye out for these pieces and make sure they are not lost. Using your old shockcord, untangle the ends and place them next to your new shockcord. the length of the new piece of shockcord should be trimmed to match the length of the original The replacement part should be approximately 8 inches shorter than the previous section if the old shockcord has become stretched out and no longer has its elastic properties. Tighten one end of the shockcord and pass the other end through all of the pole sections until the last one
  4. Make a temporary knot in the shockcord to prevent it from slipping back into the second-to-last pole piece
  5. Alternatively, you may use a pair of locking pliers to secure the cord in place. Feed the remaining shockcord through the final part of the pole and tie the end together. Return to the beginning and untie (or unclamp) the rope that connects the final two pole parts. Check to make sure that all of the pole components are securely fastened to the completely completed pole. If the shockcord is still too slack, untie one end and pull it out 6 inches at a time until the poles are securely fastened together when the shockcord is tightened. It is important not to over-shorten the rope. Using pliers, remove the parts of the pole and fold it up starting at the center position

Related Articles

  • Starting with the tent pole, make sure it is straight and parallel to the ground. Sections can be labeled with a permanent marker (masking tape can be used if you don’t want to write directly on the pole) to prevent them from being mixed up. Take a pair of scissors to the old cable, and then carefully take the elastic out of the pole end
  • Watch out for maintaining the same sequence and orientation for all of the pole parts while you’re working. A little metal item at either end of some tent poles, which serves as a tie-down point, should be kept an eye out for and avoided at all costs. Using your old shockcord, untangle the ends and place them next to your new shockcord
  • The new portion of shockcord should be cut to the same length as the old section The replacement part should be approximately 8 inches shorter than the previous section if the old shockcord has become stretched out and no longer is elastic. Make a knot in one end of the shockcord and pass the other end through all of the pole sections until the last one
  • Stretch the shockcord to increase its length, and then tie a temporary knot to prevent it from slipping back into the second-to-last pole piece
  • Alternatively, you may use a set of locking pliers to hold the cord in place while you work. Feed the remainder of the shockcord through the final part of the pole and tie the end together. Repaint the area where the final two pole parts were tied together (or unclamped). Ensure that all of the pole pieces are securely secured in the completely built pole by performing a final inspection. Remove 6 inches of shockcord at a time, untying one end at a time, until the poles are securely held together when the shockcord is tied in place. Keep the cable from becoming too short. Remove the parts off the pole and begin folding it up from the center point
  • This should take around 15 minutes.

Contributing Experts

Jon Almquist works as a product manager for tents at the REI Co-op headquarters in Kent, Washington.

Laura Evenson

Currently, Laura Evenson works as a sales lead in the camp and climb departments at the REI Conshohocken location in Pennsylvania. Laura’s 2013 Appalachian Trail thru-hike included 27 consecutive days of rain, demonstrating her tenacity as an adventurer.

Chris Pottinger

Chris Pottinger works at REI Co-op in Kent, Washington, as a senior tent designer.

Lindsey Stone

Currently based in Seattle, Lindsey Stone works as the operations director for Rainy Pass Repair Inc. Prior to that, she worked as a professional sewing technician for a total of 12 years. Her family, which includes her husband, kid, and dog, likes hiking, camping, and canoeing together.

How to Replace Shock Cord in Tent Pole

The operations director at Rainy Pass Repair, Inc., in Seattle is Lindsey Stone, who has been there since 2004. She had worked as a professional sewing technician for 12 years before starting her own business. Her husband, daughter, and dog accompany her on hikes, camping trips, and canoeing excursions.

What is a tent shock cord and why is it important?

Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.

See also:  How To Clean Mold Off Nylon Tent

Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.

What you need to replace the shock cord in a tent pole

Make sure you have all of the materials you’ll need before starting to work on your tent repair.

A replacement shock cord may be purchased at your local camping store, and there are several companies who sell shock cords online as well. You will require the following materials:

  • The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
  • Scissors or a sharp edge
  • Measuring tape
  • Sharpie or marker pen
  • A lighter or matches to melt the ends of the wires Tape for masking

How to replace a faulty shock cord in a tent pole

The moment has come to get started on mending your shelter now that you have all of the equipment you need, as well as some new shock cable to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will see that your tent pole will come apart into its many components after the cable has been severed.

  • Because it’s probable that the pole portions in the middle are similar, the end pieces where the rope is knotted are the most critical parts to avoid getting mixed up in the process.
  • Perhaps you’ll need to remove your grommet pegs and then untie the remaining cable before you can continue.
  • 2.
  • Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
  • Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
  • If you are unable to use your previous cord as a reference, measure and mark the new cord to be approximately 8 inches shorter than the pole, or around 75% of its overall length.
  • You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.

Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.

Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.

Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.

When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.

When you’ve reached the desired length with the string, tie a knot here to ensure that the peg is secure.

Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.

All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable inside a tent pole.

All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.

The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.

If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.

How to Repair a Shock Cord if it Breaks in the Field

A snapped or overstretched shock cable might make erecting your shelter more difficult if you’re already out on the trail during your camping vacation. If you want to repair the wire without having to replace the entire length, fortunately, there is a simple solution. However, while this is not a permanent solution, it will allow you to use your tent for a short period of time until you can replace the cord completely. If the cable hasn’t snapped, but rather has become too stretched out to go around your tent pole, there’s a simple solution.

  • Then, draw the shock cable through the grommet peg until it is taught once again, and reattach it to the grommet peg.
  • If the shock cord on your old tent pole has snapped, you’ll need to remove the pole using the steps outlined above to fix the problem.
  • Remove a few inches of the cord’s elastic core on each side of the break, leaving only the braided sheath on the other side.
  • The reason you need a thinner segment of cord to tie the knot is so that the knot will not become trapped in the poles and will be able to flow through freely.

Using string as a temporary replacement for a broken shock cord

If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can purchase a new replacement cable. Although this will not have the same elastic characteristics as real shock cable, it can be used as a temporary replacement until you can make more serious repairs. Keep this in mind when using this. All you need to execute this DIY patch is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a small number of supplies.

  1. Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
  2. Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
  3. This will make it much easier to thread the string back through the tent.
  4. Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
  5. Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
  6. Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.

When you’re finished, we recommend that you unfurl your poles to make sure there’s enough slack to pack away your tent properly. Any mistakes can be corrected by untying the end at a peg and making any required modifications.

How to repair a broken tent pole

The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a damaged tent pole as well as changing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.

  1. Purchasing a repair sleeve is a cheap option if your tent does not come equipped with one; you never know when you might require one.
  2. If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
  3. If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
  4. Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.
  5. Using duct tape, secure a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did previously.

Preventing damage to your tent poles in the future

If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.

When building your tent and connecting the tent poles, start with the central segment and work your way out from there.

This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.

You’ll be considerably more likely to prevent repairs and replacements in the future if you follow these few simple suggestions. If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.

Final Verdict:

It is occasionally required to replace the shock cord in your tent pole, but it does not have to be a difficult process. It is possible to save a large amount of money by making minor repairs and replacements to your camping equipment over time, and it is also considerably healthier for the environment. Learning how to execute these little repairs is simple, and more importantly, it will make you a more experienced camper. As an added bonus, watch this video for some further tent pole repair advice!

How do I repair the shock cord at the center of my pole?

This page was last modified on Tuesday, March 9, 2021 at 10:26 a.m. If you have a shock cord that has become stretched out, gone slack, snapped, or is just worn out and in need of replacement, you have come to the proper spot to get it replaced. This is really a fix that can be completed rather fast and simply at home with little tools. Quest Outfitters carries shock cord, which can be obtained at most hardware stores, outdoor retailers such as REI and Moosejaw, and sporting goods stores.

DIY Shock Cord Replacement

You will need 1/8″ thick shock cord that is around 1-2 feet longer than the length of the complete pole for each pole (for example, if you have a 10ft pole, obtain roughly 12ft; others think a 34% ratio may be preferable.).

  1. The shock cord will be wound in a knot once the end tip has been removed (either on a washer or on the end tip of the pole). Cut the knot and you’ll be able to remove the shock cord with ease. The most essential thing to remember is to remove the pieces of each pole in the same sequence that you removed them. After you have removed the old shock wire, you will be ready to thread the new shock cable on each pole. Remember to string them back together in the same sequence. Gently push the shock cord through the entire length of the pole, then tie it off at one end (either with a simple knot or with a loop attached to the pole tip)
  2. Then, to tension the shock cord, pull out about 25% of the total length of the pole in slack (for a 10ft pole, pull out 2-3ft), and tie it off at the pole end. After that, you may check the tension and make any required adjustments
  3. The pole parts should softly seat themselves. Keep in mind that this is not an exact science, so use your best judgment and common sense while making decisions. Remove any extra shock cable after that, and you’re finished

Here’s a link to a fantastic tutorial from REI that goes over the process of fixing tent poles and includes a part on how to restring shock cord at the base of the pole: Fixing a Tent Pole (with Pictures) Did you find it to be of assistance? Yes NoFeedback is not required.

How to replace shock cord in tent poles

Have you ever experienced that shaky, jittery feeling in your stomach? I’m talking about the one when your tent poles don’t instinctively want to snap together, but instead stand at attention like slender, lightweight soldiers on display. Even if you’ve owned your tent for a long time and taken it on a number of trips, sooner or later you’ll need to learn how to replace shock cord in tent poles. Here is a video tutorial showing you how to do it step by step. The good news is that changing the shock cable in your tent poles is not difficult to accomplish.

Listed below is the procedure I used to replace the shock cable in my Macpac Sololighttent.

You will need:

  • Repair or replacement shock cord (check with your local hardware store, maritime store, eBay/Amazon, or tent maker for options)
  • Scissors
  • Sticky tape (gaffer tape, masking tape, duct tape)
  • Sharpie

In addition to losing its stretch, this ancient shock cable featured substantial regions of damage where the cord looked to have been welded to itself, which was discovered upon investigation.

See also:  What Is The Tent Outside Capitola Mall Ca

Step 1: Remove the old shock cord

The method for gaining access to and removing the cord varies depending on the type of tent. Each end of mine had a straightforward screw top fitting. As an alternative, you can simply cut the cord and slide it out from underneath.

Step 2: Keep the poles in order and number them

Those clever people who design our tents may have specified a certain order in which the poles must be installed in order to guarantee that the tent maintains its proper shape. Consequently, number your poles so that you can quickly put them back together again. much as you would while cheating on a crossword problem.

Step 3: Tie a knot in one end and secure

Taking note of how the maker fastened the final knot may be beneficial so that you may replicate it later.

Remove any surplus material from underneath the knot.

Step 4: Start feeding through your cord

Make your way around to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through until you reach the lug and secure it in place.

Step 5: Continue threading poles in order

Move to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through to the lug and fastening it securely in place with your fingers.

Step 6: Apply tension and hold in place

As you near the end of the rope, you will need to apply some stress to the elastic shock cord in order for it to make it all the way to the other side. While threading the final pole, you’ll need to secure it with some tape to keep it from moving about.

Step 7: Test the tension

Test the tension in your tent poles by bending them into the approximate form of your tent frame before tying everything off at the end.

Step 8: Tie a knot in the end and secure

Secure the end lug with a knot at the end of your cording project. Insert the knot and lug into the end of the pole and tighten them together. Posted on September 13, 2019 in How To by admin

How do I replace the shock cord in my pole?

Please click here to get a PDF version of these instructions. a fresh length of shock cable 70 percent the length of your pole is cut from the existing length To prevent the line from fraying within your pole, we recommend heating the ends of the cord to seal them and prevent fraying. Place the pole in the desired position and pull one of the pole’s end-stops out until the knot in the shock cord is revealed. If necessary, you can use pliers to remove the end-stop out of the way. To release the end-stop, untie or cut the knot on the end-stop.

  1. Remove the end-stop by untying or cutting it.
  2. Check to see that the end-stop is completely seated.
  3. Thread as many portions as feasible onto the shock wire while still leaving a few inches of shock cord exposed at the end.
  4. 5: Tighten the shock cord and secure it with a peg or similar item tied to the shock cord with an easy-to-release knot to prevent it from slipping back into the sections.
  5. Continue to thread the remaining portions onto the shock cord, making sure to seat them as you go.
  6. Remove enough shock cord to allow you to knot the end-stop on with your fingers.

How do I pitch a Hilleberg tunnel tent?

  • Begin by installing the poles, making certain that all of the parts are properly seated together. To set up the tent, start at one of the sides and put a pole into the pole sleeve just above the pole tensioner, sliding it all the way to the other end
  • Then, with the pole end that is closest to you inserted into the pole tensioner cup, pull the webbing until the edge of the tent reaches the holder, and repeat the process. Repeat the procedure described above with the remaining pole parts. To set up a tent like the Keron, which has two similar entrances, either end can be staked down first
  • To set up a tent like the Keron, grip the front corners and draw the tent out taut, then peg them down. When putting the tent up for the first time, it is best to relax the adjustable peg attachments so that they are at their greatest potential length. It is usually recommended that you man out your tent so that you may attain more tension later on. This is especially vital if there is going to be wind or if the weather is going to be terrible
  • Nonetheless,

As the inner and outer of your tent are meant to be pitched together, you won’t need to take them apart unless you choose to pitch one of them independently.

For more thorough instructions relating to your tent, please go to the pitching instructions website, where you may see videos of each tent being pitched and obtain a PDF of the instruction book that came with your tent, among other things.

How do I pitch the inner tent separately?

  • To begin, detach the toggles on the inner tent and pull it out of the way. Prepare the inside tent by laying it out. Attach the pole holders (which may be ordered separately) to the toggles on the sides. Using the elastic shock cords as guides, you can now slide a pole across the canvas and into the pole holders on either side of the tent. On a tunnel tent, repeat the operation with the opposite pole(s). Using the inner tent as a guide, tie a guy line to each pole at the top of each side of the inner tent and peg them out to help you build it. The Akto, Allak, Soulo, Staika, and Tarra tents require separate pole holder kits that include additional webbing to attach the pole holders to the tents
  • The Akto, Allak, Soulo, Staika, and Tarra tents do not require separate pole holder kits. Please refer to the tent descriptions to see how many pole holders are required for your particular tent type.

More thorough instructions pertaining to your tent may be found in the instruction book that came with it, which you can find here. These throwing training books are available for download as PDFs from the pitching instructional website.

My tunnel tent is noisy, in strong winds, what can I do?

Make certain that the tent is correctly pitched and that it is completely taught. When tightening the adjustable pole holders, make sure the outer tent hits the bottom of the pole holder at its lowest point. It is necessary to draw all guy lines to their maximum length and secure them with pegs. It is also necessary to secure the man lines that are linked to the vents. If you are camping in winter circumstances, you may have the benefit of being able to dig a little deeper into the snow before pitching your tent.

Keep in mind that the wind will bring more snow with it and may cause access to get obstructed.

How tight should the door band be on my tent?

The door band’s function is to maintain the door of your tent at the proper size so that the zippers may operate properly. It is made of nylon. A tight enough door band is required to ensure that there is no stress across the zippers in order for this to be accomplished. The door band, on the other hand, should not be overtightened to the point where the door hangs freely when the door is closed.

How tight should the ground straps be on my tunnel tent?

When using our tunnel tents, the ground straps assist in maintaining the right height and tension of the poles. When they are properly fitted, there should be no stress on the connections that join the inner and outer tents caused by the poles themselves. Because of the excessive tension created by the ground strap, the poles will be put under unneeded stress, and the inner tent will droop inwards at the sides.

My tent has seen a lot of heavy use, how can I re-treat the fabrics?

In addition to being extremely robust, our textiles are also waterproof and highly water-repellent. Sun, wind, rain, and wear, on the other hand, will deteriorate any cloth with time. More information on how ultraviolet light may degrade textiles can be found here. Re-treating the fabric will increase both the protection against UV damage and the water repellency of the fabric, but it will have no effect on the tear strength of the cloth. Restoring the condition of your outer tent The Nikwax TentGear SolarProof, which is simple to apply and does not contain fluorocarbons, is the product we suggest for re-treating our outer tent materials.

TentGear SolarProof should be sprayed or brushed over the cloth, and any surplus liquid should be wiped away.

Please keep in mind that TentGear SolarProof should not be used on a new tent, but rather on a tent that has lost its water resistant capacity over time.

Restoring the condition of your inner tent Nikwax TX may be used to restore the water repellency of your inner tent after it has been exposed to the elements for an extended length of time.

Spray the TX with the same method as with TentGear SolarProof. Directly after, wipe away any extra liquid and allow it to dry. We encourage you to visit if you would like additional information about these items as well as information on where you can purchase them.

My tent is dirty. How do I clean it?

Setting up your tent and then cleaning it with a sponge and lukewarm water after your journey is a wonderful idea once you return from your adventure. We strongly advise against the use of any cleaning chemicals. Using a tiny brush, thoroughly brush the zippers to ensure that no sand or grit is left in the teeth of the zippers is also essential. Sand in the zippers can wear out the sliders, preventing them from functioning correctly again after they have been cleaned. Check and double-check that your poles and pegs are clean and free of damage before using them.

If the tent is really unclean and dusty, we usually wash it in the washing machine.

No matter how you clean it, be certain that the tent is totally dry before putting it away for the season.

How do I use a line runner?

1. To loosen the Line Runner, use your fingers to draw the line away from the Line Runner’s body, as indicated in the illustration. Pulling the line into the Line Runner’s channel will secure it in place.

My pole broke, what do I do?

One extra pole piece as well as a repair sleeve are included in each pole bag for convenience. In the meanwhile, you may use the repair sleeve to temporarily fix your pole until you get an opportunity to replace the damaged pole segment. To get a PDF with step-by-step instructions on how to repair a tent pole, click here. Making use of a repair sleeve Twelve. Slide the sleeve over the damaged pole and center it over the damaged area, then tape the ends of the sleeve together to secure it in place.

  • Pull the end-stop of the pole out until the knot in the shock cord is visible.
  • 2.
  • Untie the knot and remove the end-stop off the cord to complete the process.
  • Pull the pole apart to reveal the shock cord that is hidden underneath the broken piece of the pole.
  • 4.
  • Keep track of the order so that you can replace them in the proper sequence.
  • 6.
  • Reattach the end-stop to the shock cord with a knot.

My zipper doesn’t work, how do I fix it?

When there is a problem with a zipper, the first clue that anything is wrong is that the zipper will not remain closed when you try to zip it closed. What generally causes this is dirt and grit in the zipper, which wears microscopic grooves on the inside of the zipper slider as a result of the zipper being used. You may make a temporary repair by pinching the edges of the zipper slider together until you have the opportunity to replace it. It is critical to clean your zippers on a regular basis in order to avoid this from happening.

  1. In order to replace the zipper sliders, first open up the stitches at one end of the zipper and then remove the little metal clip that is attached to it.
  2. Remove the old sliders by sliding them off.
  3. Install the new sliders by sliding them on and making sure that they are facing in the same orientations as the previous ones.
  4. Double-check that the sliders are aligned appropriately, not only in the front and rear but also in the top and bottom.
  5. It might be difficult to put the slider on with the flat end first on some occasions.
  6. 6) Once you’ve begun to slide the zipper slider along the zipper, continue to pull on either side of the zipper to complete it.

7, 8. Once the sliders are in place and functioning properly, rejoin the stitches you undid and sew a few stitches to seal the end and prevent the sliders from coming loose again. Reset the metal clip if at all feasible.

How do I attach a line runner?

12. Feed the guy line through the opening on the bottom of the Line Runner, which is triangular in shape. 3. Pull the line through the connection point until it snaps into place. In the same manner as shown, thread the second end of the guy line through the other hole on the top of the Line Runner. 5. Tie the end of the guy line in the manner indicated on the right side of the picture. We propose that you tie your knot using an overhand knot. This completes the installation and makes your Line Runner usable.

See also:  How Many People Can Fit Is A Beer Tent For The Munich Octoberfest

How do I attach the Footprint?

The best time to attach your Footprint to your tent is just before you want to go camping. Lay your tent out on the floor with the floor facing up if you’re indoors. The Footprint should be placed directly on top of the tent floor with the logo side facing the floor, and its logo should be aligned as follows:

  • If the Footprint extends into the vestibule, the logo or logos on the Footprint should be aligned with the centre of the main outer tent door or doors if the Footprint covers the vestibule. Keep in mind that the main door on the Kaitum GT and Nallo GT is the large entrance, rather than the small entrance near the front of the extended vestibule
  • If the Footprint does not cover the vestibule, the logo on the Footprint should align with the logo on the inner tent door
  • The Rogen is an exception to this rule due to its asymmetrical design. When the Rogen Footprint logo is displayed, it should be in alignment with the logo that appears on one end of the Rogen outer tent.

Look on the back of the Footprint’s hang tag for specifics about your particular tent model. Once the Footprint is properly oriented, attach the toggles that are located around the circumference of the Footprint to the rings that are located at the bottom border of the outer tent’s bottom edge. When the tent is fully assembled, the reflective side and logo should be facing upward. When you pack up your tent at the end of a trip, you may leave the Footprint still connected. Just make sure that the entire tent, as well as the Footprint, is totally dry before putting it back in its place.

Why do the footprints on the Anjan, Rogen, and Niak tents not cover the vestibule?

The optional Footprints do not cover the vestibules on the Anjan, Rogen, and Niak tents since the outer tents do not extend all the way to the ground on these three models. During heavy rains, water can seep into the vestibule through the space between the outer tent wall and the ground in the vestibule. If the Footprint covered the vestibule area, water may seep below the tent and cause it to collapse.

My tent is paler after a lot of time in the sun, what happened?

In addition to being extremely robust, our textiles are also waterproof and highly water-repellent. Sun, wind, rain, and wear, on the other hand, will deteriorate any cloth with time. A faded or bleached appearance to the fabric indicates that the cloth has begun to be affected by ultraviolet rays. UV rays from direct sunshine have negative effects on our skin, and the same is true for all materials, including tent fabrics (which is terrible). With prolonged exposure to the sun’s radiation, particularly at altitude and in the southern hemisphere, the performance of a cloth can be compromised.

Extended exposure to ultraviolet radiation (UV) weakens the tear strength of any fabric, which is one of the primary reasons we employ materials with high tear strength.

This, on the other hand, does not imply a deterioration in the fabric’s waterproofing properties.

More information on how to withdraw your tent may be found here.

Pitching your tent in the shade with a tarp over it and not keeping it set up during the day while you aren’t using it can help you achieve this. In high UV conditions such as high altitude, glaciers, and deserts, this is especially crucial since the skin can burn easily.

How do I roll my outer tent door?

We recommend rolling the door in a certain manner rather than just bundling it and securing it with the toggle because it works better to keep it out of the way, it is more secure, and it keeps the door and zipper from dragging in the mud, which will extend the lifetime of your tent. To roll the door, begin by rolling the fabric of the door in the direction of the toggle. As you continue, collect the cloth toward the toggle by folding the loose end of the roll in and gathering the fabric. One of the objectives is to bring the main body of the door, including the zipper’s end, beneath the toggle.

Pull out the elastic loop and thread it through the toggle when you have the door fully rolled.

Pole Cord Repair for your tent

The absence of an elastic rope has no effect on the structural integrity of the tent. It is also simple to change, whether out on the field or once back at the house. All you have to do is get some elasticated cable. We include around 5m of 3mm diameter cable with our pole kits, but 2.5mm and 3mm diameter rope may be purchased online or through outdoor merchants as well. Remove the old rope and make a note of the sequence in which the poles should be reassembled before proceeding. While it is not necessary with an Outwell tent, you will discover that the pole sections of other types can sometimes differ, and you will also want to make sure that you have the correct end poles if you want to prevent having to rethread everything once you have finished.

  1. Pass the opposite end of the cable through the pole.
  2. In our pole replacement kits, we provide a narrow twisted gauge wire that is easy to work with.
  3. Although we recommend that you tape the cable to the wire, it is simpler to slightly crimp the loop to guarantee that the wire and cord slide through the pole’s 4mm diameter hole with no difficulty.
  4. Once it arrives at the conclusion of a segment, pull through.
  5. As you finish each component, make sure you connect it to the threaded section that came before it.
  6. Place the knot in the working end of the rope and insert it into the metal socket to complete the installation.
  7. Here’s our best tip for keeping your tent and camping gear as clean as possible.

Amazon.com : tent pole shock cord

THE RESULTSPrice and other information may differ depending on the product size and color selected. Ships to the Netherlands are available. Only 7 of these items are left in stock – purchase soon. Ships to the Netherlands are available. There is just one left in stock, so act quickly. extremely well-liked | This post is sponsored by Based on the number of customer reviews and the star rating Ships to the Netherlands are available. Order quickly as there are only 5 left in stock. Ships to the Netherlands are available.

  • Ships to the Netherlands are available.
  • Ships to the Netherlands are available.
  • A 5% discount is applied at the time of purchase.
  • At the time of purchase, a 6% discount is applied.
  • Ships to the Netherlands are available.

Ships to the Netherlands are available. There are only 4 left in stock, so act quickly. Ships to the Netherlands are available. Only 6 of these items are left in stock – purchase soon. Ships to the Netherlands are available. Only 15 of these items are left in stock – purchase soon.

GOLBERG Elastic Shock Cord – 2.5mm, 1/32, 1/16, 3/16, 5/16, 1/8, 3/8, 5/8, 1/4, 1/2 inch diameter – Various Colors – 10, 25, 50, 100 ft lengths – Made in the USA (Neon Orange, 3/16in x 25ft)

Ships to the Netherlands are available. Only 7 of these items are left in stock – purchase soon. Ships to the Netherlands are available. Only 11 of these items are left in stock – purchase soon. Brands that are associated with your search

How To: Replacing the cord in your tent poles

17th of July, 2020 Tension is applied to tent poles by the use of shock cock, an elastic string that aids in the snapping back together and maintaining the form of the tent poles. It is possible for the elastic in the shock cord to degrade with time, causing the cord to sag and, eventually, making your poles very difficult to use and practically impossible to use. A replacement tent pole set may be rather expensive, so if your poles are still in good condition, it is significantly more cost effective to simply change the cable.

Because these tent poles are from my Sierra Lightning II FL, and because no two tents are exactly alike in terms of size, the quantity of shock cord you’ll need may vary depending on your tent.

When determining the quantity of cord to purchase, I find it better to just purchase the same amount as your pole dimensions to allow for some margin of error.

Shock cord is available at most respectable camping stores as well as on the internet.

What you’ll need:

  • Shock cord (with a diameter equivalent to your present shock cord and a length sufficient to cover the length of your poles)
  • Scissors with a good edge
  • The following items are required: Tweezers and wire (you may use wire from a coathanger, or check out what you can get at craft stores or Bunnings if the wire has to be thinner to fit through the ferrule)*
  • A helping hand

• Shock cord (with a diameter equivalent to your present shock cable and a length long enough to accommodate the length of your poles); Scissors with a good edge. The following items are required: Tweezers and wire (you may use wire from a coathanger, or check out what you can buy at craft stores or Bunnings if the wire has to be thinner to pass through the ferrule)*; An assisting hand;

Step 1

Prepare your tent poles by laying them out. Because you’ll be unthreading them, you’ll want to do this in a place where you have lots of space to keep them organized.

Step 2

The end stop at the end of your tent pole should be removed. Removal of the end stopper* If your tent poles are the older design with a stopper or washer in the ferrule, you’ll need to take the knot out of the stopper with tweezers and cut or untie it to allow the new rope to pass through and out of the way. When you reach to the other end, you’ll have to repeat the process in the opposite direction. The difference between poles with a pull-out end stopper and poles with a washer is seen in the diagram to the right.

Step 3

Untie the string or cut it at the end stop and set the end stop on the ground. As you begin to remove the old shock cord, make sure to arrange your tent poles in the same position as you did previously. Taking the cable out

Step 4

Obtain your new piece of shock cable at this time. I’ve pre-measured my and indicated the place where I want it tensioned to, but I’m not going to cut it yet since I find it simpler to tie and cut it once it’s already been tied. Begin with the first piece of pole and pull your shock cord all the way through to the stop at the end. Then tie a knot around the end stop to keep it in place. INVERTED STOPPER: If you’re working with an inverted stopper, you’ll want to make sure your wire is prepared.

When you reach to the end, tie a strong knot large enough to prevent the shock cord from passing through the hole again. Then pull the shock cable all the way through to secure it. Feeding the wire through the washer is a simple process. Pulling the shock wire through the washer is a good exercise.

Step 5

Now that the end has been attached, draw the shock cord through the remaining sections of poles, being sure to retain them in the same sequence as they were originally put out.

Step 6

Once you’ve reached the end, tighten the cord until you see a mark on it, then secure it to the end stop, making care to maintain the proper amount of tension in the cable. Before cutting the rope, I prefer to double-check that the tension is correct. In order to keep the poles together, the shock cord should be tensioned just enough to keep them together, but not so much that the shock cord is over-strained when the poles are folded. STOPPER WITH AN INVERTED POSITION: Before you get to the end, you’ll need to take a break before the final stretch of poles is reached.

Now, re-grab your wire and push it through the final length of pole, starting at the other end and working your way toward the end stopper.

Return to the other end of the stopper and undo the knot on your second-to-last piece of pole section and fasten it to the wire.

Adjust the tension as needed, then finish with a knot that is large enough to catch on the hole.

Step 7

When you’re satisfied with the tension, cut the cord neatly and tuck the end back inside the pole sleeve with the end stop, securing the end stop with a screwdriver. The shock cord may require assistance in this area since it is difficult to cut and is much simpler to cut when someone else is tensioning it for you.

Leave a Comment

Your email address will not be published. Required fields are marked *