How To Set Up A Wall Tent Without A Frame

How to Set Up a Wall Tent Without a Frame

You’re planning a camping trip in the great outdoors, aren’t you? Don’t forget to bring along the tent as well! Wall tents give a safe haven for sleeping, cooking, and staying out of the weather. Alternatively, they can be set up without the need of an internal frame, however some alternatives do not. Building a wall tent without a frame takes a substantial amount of rope, as well as chopped tree saplings or branches, or a mix of the two. If you intend to camp above the tree line, it is recommended that you utilize the frame system that came with your tent.

We’ve got you covered with this step-by-step instruction.

However comfortable your camp is, if you do not have a decent camping tent, your camping experience will not be nearly as satisfying as you would like it to be.

Choose an Open, Leveled Area with Nearby Trees

So you’ve horse-packed into the forest or driven as far as you possibly can in your vehicle, and it’s time to pick a campground. As long as you don’t have an inside tent structure on hand, it’s critical that you seek for a leveled location in an open clearing. No matter whether you use ropes or cut saplings to support your tent, you’ll need to situate it near a few trees of varied sizes that you’ll be relying on in one way or another to keep the tent up. Building your tent on level ground gives for a far more comfortable experience in various respects, including the following:

  • Water is prevented from running downhill toward and below the tent using this device. As a result, campers in their sleeping bags do not have to struggle against the inclination while sleeping. As a result, it eliminates the discomfort of rolling into another camper while sleeping. Inside the tent, it guarantees the safe functioning of a camp stove

Establish Your Tent’s Orientation and Put Down the Floor

Many wall tents are built to allow you to set up a stove inside and exhaust it out a hole in the side or roof of the tent using a stovepipe. This type of tent must be put up in such a way that any prevailing winds blow smoke and sparks away from the tent if it is to be used in this manner. Check to be that the space beneath the tent is free of rocks, sticks, and other debris before setting up the tent. If you want to sleep on the ground, this will help to protect your tent floor as well as your back.

Additionally, it will aid in keeping the tent’s bottom clean and will give additional protection against moisture seeping in.

Unzip all of the windows and doors to relieve some of the tension on them as you prepare to raise the tent in its final position.

It’s possible for some people to believe that any type of tent would suffice for camping, however this is incorrect. If you feel the same way, read this article to find out why you need a nice camping tent in the first place.

Set Up a Rain Fly

The rain fly must be installed prior to constructing the support structure and raising the tent in order to provide additional protection from any downpours or snow that may occur, since adding a rain fly once the tent has reached its maximum height can be difficult. Essentially, a rain fly is merely another name for a tarp. It is possible to attach a rain cover to the trees surrounding the campground with a basic plastic tarp and some rope threaded through the grommets at the top.

Create the Tent’s Support Structure

Remember how we told you to seek for a campground with trees nearby? That’s right. Now is the time when they will come in helpful! Because you are not utilizing a premade interior structure to support your tent, you will have to improvise in order to keep it up. The majority of wall tents are constructed in the same manner. The following are the primary structural components that give the tent its shape:

  • Aridge pole is a long pole that serves to define the centerline of a roof
  • It is made of wood. Eave poles are threaded through sleeves at the top of each side wall where the walls meet the roof slope, and they are attached to the roof by a ridge rod. One of these is on either side of the tent, and there are two of them. Using rafter support, you can keep your tent ceiling from drooping. Wall poles provide support for the side walls.

It is necessary to substitute something for these poles in order to lift and sustain the tent at its maximum height when it is not supported by a frame. This may be performed in at least five distinct ways, and the manner you pick will be determined by your own tastes as well as the kind of natural materials that are readily available in your local area.

Use Cut Saplings to Replicate a Full Frame

Look around for saplings or long branches that you can cut into pieces that will fit through the sleeves of your poles. If your tent is more than 10 or 12 feet in length, you may need to acquire saplings with a diameter of 1 inch or less, depending on the size of your tent. The number of saplings required is listed below. At the absolute least, you will need to locate and cut the following items to the appropriate lengths for your tent in order to recreate the whole inside frame.

Tent Component Number of Saplings
Ridge pole 1
Eave pole 2
Rafter 4 – 6
Wall pole 4 – 6

It might take many hours to choose the correct size and number of trees to chop for a given project. If you decide to use this strategy, make sure you have enough daylight to complete your collection before dark. Using the cut saplings, feed them through the sleeves at each of the pole placements. If they are too large to pass through the sleeves, arrange them in the same approximate location as the rest of the group and drape the tent over them. When you’re going camping, your tent isn’t the only piece of equipment you’ll need to carry with you.

We’ve compiled a list of all the camping equipment you’ll need for a weekend in the great outdoors to assist you in making sure you have everything you’ll need for your camping trip.

Use Saplings and a Rope

If you want to utilize saplings with rope, here’s what you need do:

  1. Search the surrounding region for three saplings that will serve as the ridge pole and A-frame support
  2. One sapling should be threaded through the ridge sleeve and tied to a neighboring tree with a piece of rope. As an alternative, if it does not fit into the sleeve, set it on the roof’s midline and drape the tent over it. Make an A-frame out of the remaining two saplings and place it at the door end of the tent to keep the bugs away. The ridge pole will rest in the V-shape formed by the two poles being lashed together at the top of the structure. Sticks should be found or chopped into five-foot lengths in order to be used as wall poles.

Alternatively, you may use six saplings to construct two A-frames, one for each end of the tent, with one at each end. On both ends, the ridge pole will be supported by these frameworks.

Use Rope Only

If you don’t have any useable long saplings or branches, you may always use rope to provide a temporary solution.

The rope is used in place of all of the poles in this technique of construction. The walls and ceiling will sag somewhat, but you will still have a fully functional tent as a result of this. To do so, follow these steps:

  1. Attach the rope to a tree by threading it through the eave sleeves of both walls. Attach two trees to either end of the rope that has been threaded through the ridge sleeve.

Use Rope and A-Frames on Each End

In order to use rope and A-frames on either end of your wall tent, you must follow the instructions outlined below:

  1. Build an A-frame for the ends of the ropes and run them through the eaves. Using the ropes, run them up and over the tops of the A-frames on either end before dropping them to the ground. Fix the ends of these ropes to the ground using stakes. Pull the tent up firmly and tight with lots of tension to keep it in place.

Use Saplings for Two X-Frames for Each End

Finally, if you wish to utilize saplings to construct two X-frames, you may do it as follows:

  1. Cut eight saplings in order to construct four X-frames. Each X will have one pole that is approximately one-third longer than the other. For each X, lash the two poles together closer to the ground—approximately two feet above the ground
  2. Using the longer pole facing toward the ridgeline, make an X at each corner of the room. Ideally, the longer poles should cross each other at the ridgeline and be lashed together. Restrain the ridge by running a rope or sapling through it, or tie long poles to the ridge and use them to hold up the tent’s ceiling. Glue the rope or saplings to the top of the walls at the bottom of the roof and run them along the top of the walls to link to the X’s and keep the walls tight and upright.

It is one of the first problems you will face while going camping that is the process of putting your tent up. You should consider using a pop-up tent if you don’t want to deal with the inconvenience and stress of setting up a tent. Learn more about the operation of a pop-up tent by reading our article.

Stake the Tent

Once the tent has been erected to its full height, it is necessary to anchor it down to protect it from strong winds. Most tents are equipped with grommets along the outside eaves, which are used to tie guy lines to the tent’s walls.

  1. Tent stakes should be driven into the ground at a 45-degree angle, with the stakes leaning away from the tent. We propose that you place one at each corner as well as at the midpoints of each side of your building. Attach guy ropes through the grommets along the sides at an angle that is approximately the same as the roof’s pitch. These should be staked into the earth. You can consider anchoring the tent’s guy lines to adjacent trees or logs—something with a little weight to keep the tent from blowing away—if you’re in a very windy location.

How Long Does It Take to Set Up a Wall Tent?

When it comes to erecting a wall tent, size does important. The greater the size of the tent, the longer it will take. Furthermore, whether or not a frame is used, it is evident that it will take significantly less time to set up if at least two people are involved in the process. Certainly, building a wall tent on one’s own is difficult, however it is possible. Remember to give for lots of additional time if you’re doing it on your own timetable!

  • In most cases, it takes 15-20 minutes to set up a tent on a prefabricated frame. This process may take you 20 to 25 minutes if you are also setting up the stove and stovepipe. Building a wall tent with external support can take several hours, especially if you have to hunt down and cut your support poles first, which can take several hours. If you live in a rural region, you may have to seek a large radius to obtain the size and length of saplings you require
  • Depending on the situation. If you simply require a few chopped saplings and a length of rope, the time required should be reduced to around one hour.
See also:  How Much Does A 20X20 Tent Cost

Tools Needed to Set Up a Wall Tent Without a Frame

It’s natural for the first thing that comes to mind to be “practice, practice, practice.” If you want to put up your tent without a frame, don’t wait until you’ve arrived at the location. Make sure you understand how your tent is constructed, as well as what size pole alternatives you will need to locate in the forest. In addition to the tent itself, you might want to consider packing the following accessories:

  • A pair of plastic tarps: one for the ground barrier and another for the rain cover
  • The tent’s support rope is made of: Take plenty of rope with you! A sufficient amount will be required to pass through both side eaves and the ridgeline. The type of structure you pick will determine how much rope you’ll need to reach out in numerous directions to tie around adjacent trees. Guy line rope (also known as a guy line): Utilize this rope to fasten the tent to adjacent trees or logs in order to keep it in place
  • You’ll need a hatchet or a saw to chop down the saplings that will be used as the ridge pole, eave poles, and sidewall supports for your structure. Stakes for a tent: In order to secure the tent to the ground, metal or plastic tent pegs should be used. The use of a mallet is necessary to drive tent pegs, guy wires, and A- or X-frames into the ground
  • Other uses include:

Final Thoughts

The technique of erecting a wall tent without the aid of a frame is difficult to master. You will almost certainly have a tent that is crooked or misshaped if you don’t know what you are doing. In this instance, your camping excursion may very easily come to a close before it really gets started. Fortunately, there are a few straightforward methods for erecting a wall tent without the use of a frame. We’ve showed you the most likely options above, but with a little imagination and creativity, you might be able to come up with some more options of your own.

Although it may not appear precisely as it should and may droop in some spots due to the lack of a prefabricated structure, what counts is that it keeps you dry and warm while you are outside.

Alternative Ideas for Wall Tent Frame?

Hello everyone, here’s hope that someone else has come up with a solution or two for this problem. With a 10X12 wall tent and a robust interior structure built of conduit, I’m ready to go. The frame is heavy and big, which is OK for truck camping, but I’d like to make it lighter and smaller for moose hunting on a small boat. What I’d want to find out is a less expensive approach to bringing the internal frame into the room without having to create a complete traditional exterior frame from scratch.

I’ve heard stories about Canadian Rangers constructing a foldable ridge pole out of 2X4s (I would love to see pictures to better understand).

When it comes to building ridgepoles using a ratchet strap between two trees, I like the idea, albeit it would depend on whether or not your site has the appropriate trees.

If you have any suggestions or images, please share them with us. The more the portability, versatility, and ease of setup, the better the system.

How to Prep and Set Up a Wall Tent

This tutorial will show you how to prepare and set up a wall tent from scratch. A wall tent differs from a standard tent in that it provides enough space for you to stand up in one of these tents. As a result, the setup is, to be expected, a little different. You may view the video by clicking here. For your convenience, we have broken the instructional and video into portions so that you can more easily follow the directions. In any case, comprehensive instructions will be provided later on.

  • Poles ten feet long and one inch in diameterEMT poles fifteen in number2.
  • The Wilderness Canvas Wall Tent is available for purchase.
  • A wood-burning stove (for warmth and cooking) Paint, masking tape, and a spray gun 5.
  • Tools for trimming the poles (saw, metal blade, measuring tape, angle grinder, etc.)

Step 1: Prepthe Poles

After obtaining the poles, they should be prepared in accordance with the size standards. Our tent was made using 15 ten-foot sections of 1 inch EMT that we purchased and had cut to the exact dimensions of our 10×12 tent—although other tents will have varied cut lengths. We’ll need the following items: 5Tent legs are required. 5 Tent Rafters and 5 Ridge Eaves are required. It is necessary to cut the poles to the proper length. Measure the poles twice before cutting them. Among the tools available are a hacksaw, metal angle grinder, and reciprocating saw.

We used a grinder to smooth up the ends of the pipe.

Step 2: Cut and Finish the Poles.

Tools such as a measuring tape, saw, metal cutting blade for cutting the poles, and an angle grinder were utilized to smooth off the rough edges.

Step 3: Paint the Rafters Red.

The rafters are 69 inches in length, while the eaves and ridges are 69 and 7/8th inches in length, respectively. Because there is only a slight variation in length between the two, it is exceedingly simple to become confused between the two. As a result, the rafters are color coded. Masking tape and spray paint were used for this quick work.

Step 4: Check the Contents of Your Tent Package Beforehand.

You should have the following items: 1. The canvas for the tent. We received ours from the It’s a heavy-duty, high-quality tent with a beautiful finish and an extra-large carry bag included. It is highly recommended, and we discuss it in detail in our video! It is much easier to put the tent back into its canvas bag if the bag is larger in size.) It’s a pain to attempt to cram the tent into a small, compact carrying case.) Second, the Fly Cover is utilized to provide additional protection for your tent.

Guylines- These cables are responsible for keeping your tent firmly planted on the ground.

The Angle Kit- These components assist in keeping the poles in position.

Step 5: Set Up and Cure the Stove.

Assemble the stove in accordance with the instructions provided in the user handbook. A couple of hours spent cooking on the stove is a fantastic investment. This will get rid of any paint odors that might otherwise seep into your tent fabric and linger there for a long period of time. Being confined to a tent that is always scented with paint is not a fantastic idea! During the winter, having a burner is incredibly beneficial for keeping the tent warm. This particular stove has enough capacity in it to accommodate larger chunks of wood that will burn for several hours, allowing you to sleep well without having to worry about stoking the fire.

Aside from that, it has safety elements such as a spark arrester and a lock to keep everything under control. Furthermore, the pipes are simply inserted, making the process of putting it together not difficult.

Step 6: Set Up the Tent

First, remove the snow and lay up a tarp to protect the area. Lay out the red poles for the rafters first, and then move the other poles into position so that you can easily raise the entire construction up with one motion. Canvas should be used to cover the structure.

Step 7: Lift the Tent Upwards.

Start with one side of the tent and work your way around to the other poles until the tent is fully assembled. Canvas should be used to cover the sidewalls. Because you have covered the rafters while the tent was still down, you won’t have to battle to cover the roof once the tent is up and ready to be used. If the tarp becomes too slick to walk on, as it did for us, you may simply remove it entirely from the area.

Step 8: Stock Enough Supplies to Get You Through Your Camping Adventure.

The wall tent has a lot of floor space. Aside from two cots, a handful of chairs, a table, and our stove, we have adequate space for everything else. Make sure you have plenty of food and firewood on hand at all times.

Step 9: That’s What Our Tent Finally Looked Like at Night!

Camping is a blast! Visit our website, HomesteadHow.com, for more information.

Be the First to Share

  1. Remove any pebbles or sticks from the area where your canvas tent will be set up. Determine the orientation of the canvas tent. Create an arrangement for your tent such that the prevailing winds will blow sparks and ashes from your stove pipe away from the structure. As a result of sparks landing on your roof, your roof may become damaged, and ash may cause your tent to become dirty. Lay a canvas tent floor on the ground where the tent will be positioned before setting up the tent. When you choose a floor for your tent, it will be easier to keep it clean during the setup and takedown process. Aside from that, I have an inexpensive indoor outdoor carpet that folds up like canvas that I use to cover the top of the floor. I set the canvas tent on the carpet since the tent might become soiled if it is placed on a dusty or unclean floor. Angles and tent structure should be placed on the floor in an acceptable area for set up. The 3 way angles are placed at the ends of the tent frame, while the 4 way angles are placed in the centre of the tent frame. Poles for walls, rafters, and tents can be color tagged or painted on one end no more than 1-2 inches in length to distinguish them from each other. Once the frame is created, these color-coded ends will be able to fit into the angles and will not be seen. Assemble the tent frame, with the exception of the legs on one side. By adding legs on one side of the tent frame, the ridge will be 5-6′ high, allowing you to drape the canvas over the ridge with relative ease. When installing the legs on one side of the frame, it is advisable not to attach the legs on one side first, since the ridge line will be too high to drape the tent over when the legs are installed on one side
  2. For example, if you have a Montana canvas tent with a lofty ridge line. Unzip all of the door zippers to avoid putting strain on the zippers. Tent should be draped over frame. Keep sidewalls off the ground by folding them in toward the inner of the roof’s interior. In windy weather, tie tent ridge ropes to tent roof end grommets to keep them from blowing away. Tent roof should be draped with a fly. As contrast to when the canvas tent structure is fully assembled, it is much simpler to place the fly now than it will be later. Legs should be installed. Make sure your tent is properly aligned with the frame. You should avoid pulling too hard on your tent since this can weaken the seams and zipper doors. If your tent is too small, you will need to shorten the length of your frame rafters or tent as necessary. A secure fit for the canvas tent should be achieved on the frame, without the need for any further force to bring the tent into alignment. While using your canvas tent, it is possible that the tent may continue to shrink gradually, requiring you to cut down the frame on an irregular basis. If the zipper on your canvas tent entrance is too tight, you must cut down the rafters to relieve the strain on the zipper. Install sod cloth under the floor to create an air seal and to keep rainwater from accumulating on the surface of the floor. Some campers who do not have a floor use their sod cloth on the outside of their tent to funnel rainwater away from the tent
  3. I have also seen hunters who place their sod cloth on the outside of their canvas tent and then cover it with soil to create a stronger air seal. THIS IS NOT RECOMMENDED. It is due to the dirt that the sod fabric becomes soiled. Furthermore, if it rains or snows, you will have mud on your hands, which will make it very difficult to clean your sodcloth. Recall that if you have a filthy sod cloth when you take down the canvas tent, you will have a dirty tent when you roll it back up. Stakes, man ropes, and tensioners should be installed. Stakes should be pushed in at a 45-degree angle away from the tent to ensure proper alignment. The guy ropes are positioned at an angle that is about equal to that of the tent ceiling. Whenever I’m working in an area with strong winds, I secure the man-ropes to trees, stumps, or logs. The use of two guy ropes or stakes for each eave corner is an alternative option. If rain is forecast, dig a trench around your tent that is 4-6 inches wide and 2-3 inches deep to ensure that water drains away from your tent. The instructions for setting up and taking down your canvas tent should help you maintain your canvas tent clean for years to come.
See also:  What Lessons We Learn From Living In A Tent

Taking Down a Canvas Tent (Part 1):

  1. Clean the inside of your tent by unzipping the zippers on the doors
  2. Unzip the zippers on the windows. Cleaning the interior and exterior areas of your sod cloth with a towel is a good idea. When you fold your tent with a soiled sod cloth, the interior of our tent will become soiled as well. Fold the tent walls within the canvas tent so that they are flush with the interior of the canvas tent. When taking down the tent or folding the tent for storage, ALWAYS fold the tent such that the interior of the tent touches the inside of the tent of the other portions of the tent. The dirt, dust, tree pitch, and other debris that collects on the exterior of your tent is permanent. It is possible that the exterior of your tent’s canvas may come into contact with its inside canvas, resulting in a dirty interior tent, which you will be forced to stare at while you are inside the tent. It is not recommended to pull out the wall stakes using the canvas wall, since this may cause damage to your canvas tent. It is advised that you use a claw hammer. Take down in the reverse sequence of how it was put together.

Internal Frame for Wall Tent; How many Rafters?

When we purchased our wall tent, we also purchased an angle kit for the purpose of building an inside frame. In order to save money on shipping, I purchased 1 inch EMT tubing from a local building shop and cut the poles by hand myself. Angle kits are made up of three and four-way connectors that are welded together from 114 inch (inside) galvanized steel tubing and are used to keep the 1 inch (inside) EMT tube frame together. I was informed to account for 3 percent shrinkage, so I made the necessary adjustments to the tubing.

The roof section of the tent frame’s interior wall.

Legs have not been connected at this time.

Now that I think about it, I wish I had anticipated a 1 percent shrinkage rather than a 3 percent contraction.

How Many Rafters Does your Wall Tent Need?

The first thing to think about while building the interior structure of your wall tent is how many rafters you want or need to have. A total of four rafters support our 14-foot tent, which means that the distance between rafters is four feet eight inches between rafters. Four rafters are insufficient for structural support in a tent that is 14 feet long. It’s likely that three rafters (7 feet apart) will be insufficient to sustain the tent under any but the mildest and most benign of situations, such as putting up in the backyard for a sleepover party.

The number of rafters is reduced, which lowers the cost and weight of the structure.

The internal structure of a wall tent is usually left at home when it is transported by horse or 4-wheeler.

For 12, 14, 16, 20, and 24 foot tents with varying numbers of rafters, the distance between rafters (pre-shrinking) is shown in inches in Table 1.

Table 1.Rafter spacing (in inches) for internal wall tent frames (inside the frame).

Number Tent Length
Rafters 12 Ft. 14 Ft. 16 Ft. 20 Ft. 24 Ft.
3 72
4 48 56 64
5 36 42 48 60 72
6 28.8 33.6 38.4 48 57.6
7 24 28 32 40 48
8 20.7 24 27.4 34.3 41.1
9 18 21 24 30 36
10 18.7 21.3 26.7 32
11 19.2 24 28.8
12 17.5 21.8 26.2
13 20 24
14 18.5 22.2
15 20.6
16 19.2
17 18

Consider the following example of rafter spacing and strength:

  • 60-72 inches – only for usage in the backyard
  • When the weather is excellent, 48-60 inches is a decent length for light duty, short-term use. 36-48 inches — can withstand a few inches of light snow
  • 36-48 inches When the ground is 24-36 inches deep, it can hold a foot of light snow. Semi-permanent base camp should be between 18 and 24 inches in height.

Keep in mind that heavy snow can cause any tent to collapse if it is not swept off on a regular basis.

How Many 3 and 4-way Angles Do your need for your Wall Tent?

This is straightforward, especially considering that all end rafters require three 3-way angles for a total of six angles. A 3-way angle is required on both ends for the apex, as well as one on each side where the roof meets the wall at the corners. Every wall tent requires a total of six 3-way angles. Table 2 displays the number of 3- and 4-Way Angles required for a variety of rafter sections based on their length. Three 4-way angles are required for all interior rafter sections. As illustrated in Table 2, if three rafter sections are used, there will be two end rafters and only one interior rafter, resulting in just three four-way angles.

Table 2 shows the number of angle pieces and rafter sections required for a variety of rafter counts for internal wall tent frames of varying sizes.

Total Angle Pieces Number of Sections
Rafters 3-Way 4-Way Legs Ridge Sides Rafter
3 6 3 6 2 4 6
4 6 6 8 3 6 8
5 6 9 10 4 8 10
6 6 12 12 5 10 12
7 6 15 14 6 12 14
8 6 18 16 7 14 16
9 6 21 18 8 16 18
10 6 24 20 9 18 20
11 6 27 22 10 20 22
12 6 30 24 11 22 24
13 6 33 26 12 24 26
14 6 36 28 13 26 28
15 6 39 30 14 28 30
16 6 42 32 15 30 32
17 6 45 34 16 32 34

If you are thinking about obtaining a wall tent, you should also think about getting an inside structure. Campers who are staying close to the trail head will appreciate how simple it is to set up camp. A wall tent makes it much easier to travel to those isolated trailheads that are located on terrible roads than it is to tow a trailer. It goes without saying that if you’re hauling a wall tent across a wilderness with horses, you’ll leave the interior frame behind. When purchasing an angle kit, I hope this page will make it easier for you to decide how many rafters you will need and also to account for some shrinking at the beginning of the construction process.

A Canvas Wall Tent – Camping Without Hauling a Trailer

Many years ago, we felt that a wall tent would be an excellent option to sleeping in the back of the vehicle or in our backpacking tents, especially in cold weather and when we were planning on sleeping in close proximity to the truck in any case. Naturally, we like the convenience of sleeping in a beautiful, heated camping trailer, but getting a trailer in and out of some of the rougher Forest Service and Bureau of Land Management roads can be a real challenge, especially later in the hunting season when the snow starts to pile up.

  1. In the previous ten years, I’ve witnessed two consecutive Elk seasons during which many hunters spent days attempting to get their trailers off the mountain following snow storms.
  2. I was relieved not to have been a part of that catastrophe.
  3. Every year, anyone who drives a trailer into the higher elevation mountains between mid-October and mid-November runs the risk of having their trailer stuck on the mountain for the whole winter.
  4. The weather forecasts should be closely monitored over this time period to avoid being caught out in the rain.
  5. In reality, when I was writing this, we were making preparations for a hunt that would begin in early October, and it was snowing outdoors outside.

We had been hunting at 9,400 feet on dry terrain just a few days before, but there was at least a foot of snow on the ground by then. After a few days, I was allowed to drive back up to the location, but I didn’t notice any more trailers being transported up to the location that year.

Our First Wall Tent

While researching a wall tent, we didn’t know anybody who had one, so we conducted some research into the pricing and other alternatives to consider before making our final decision and purchasing a wall tent. Based on our research, we’ve put up a shopping guide for wall tents. The tent includes two screened windows that are closed with a canvas flap that is fastened to the tent using velcro. Our tent is 12 x 14 feet in size, with sides that are 5 feet high and a center that is 8 feet high. It includes one door, a sewed in screen door, two windows and a stove jack (a fireproof fiberglass hole for a smoke stack), as well as frame angles for a four-rafter internal frame.

See also:  How To Fold A Name Tent

We made the decision to purchase the stove separately.

The tent weights around 60 pounds, and the total weight of the tent, including the 12 internal frame angles, 25 poles, stakes, and rope, is less than 100 pounds.

As a result, the wall tent may be transported everywhere the truck can drive.

Tips for Assembling the Wall Tent Frame

I can set up the entire tent with my wife in about 15-20 minutes without the stove and in about 20-25 minutes with the stove and stove pipe if we are both motivated. The construction of the interior frame is the most time-consuming element of the process. In order to facilitate assembly, the internal frame was marked at the angles and poles (see Figure 2). The frame angles are fastened to poles that link to other frame angles via which they are suspended. They are maintained in place by friction as they are merely slipped into their respective frame corners.

The ridge pole components were all painted blue, while the pieces on one side of the pole were painted white, and the ones on the other side were painted black.

Yes, I created a cheat sheet in the event that I forgot something.

Setting Up the Wall Tent is Fairly Simple

The first stage is to build the interior frame, with the exception of the legs, and then to pull the tent over the frame. Following that, one side of the frame is lifted at a time to allow the legs to be joined to the frame. The tent is then “squared up” and staked down, starting with the corners and working your way along the sides. We have built up the wall tent in less time than I have seen some people level their trailers, which is impressive. Following the setup of the tent, the floor (tarp or ground cloth) is rolled out and the cots and table are placed in their proper locations.

If we don’t want heat, we don’t set up the stove under the stove jack.

Wall Tent Assembly

That’s all there is to it, Home Sweet Home for as long as we require it to serve us. Our wall tent is, without a doubt, far more roomy and comfortable than our hiking tents. We never utilized the bigger family type tents, but the wall tent has an advantage in this situation as well since it can be heated and heated water with a wood stove, which we did not have. Is a wall tent preferable than a trailer in terms of functionality? That is dependent on the situation. Do you want to be more comfortable?

Is it simpler to pull when the roads are terrible or when the weather is bad?

And, even after purchasing the wall tent and stove, we still have money left over in our pockets.

Advantages of Wall Tent over Trailer

  • Cost: $1,000 (or less) against $10,000 (or more). There are no charges for tags, insurance, or registration. lightweight (150 lbs as opposed to 2,000 pounds or more)
  • It is less difficult to transport on rough roads
  • If the truck can travel, so can the wall tent. Storage that is small enough to fit in the trunk of a mid-sized automobile
  • It is possible to load by horseback or with a gaming cart. It is less difficult to put up on sloping terrain. In case of an emergency, a wall tent and a wood stove may always be utilized as shelter.

Advantages of Trailer over Wall Tent

  • Comfort — there is no doubt that a decent, well-equipped trailer is more comfortable. Occasionally, water may drip down the frame and pool on the floor. Wood stove vs. gas heater: The wood stove requires more maintenance (wood heats you twice as much as propane)
  • People, bears, and nasty crawlies pose a greater threat to security. As a precaution, we set up a small electric fence when we are concerned about bears. It is possible that the ground within the tent is not level.

Please let us know if you have any further pros or negatives to add.

A Second Wall Tent

Our Elk Mountain Wall Tent is 13 by 13 feet. Elk Mountain Tents has provided us with a second wall tent. Due to the fact that we have two tents, we can accommodate additional family members or guests without feeling cramped or having to give up our privacy (or theirs). Take a look at how much space is available for our two cots and the wood stove. A handful of photographs shot recently on a late-season hunting trip are shown below: The fact that there was no snow on the ground is astounding, but it was still cold enough at night that we were glad to have the Cylinder stove to keep us warm.

Keep an eye out for a comprehensive review in the near future.

What exactly are your worries?

Continue reading our posts about wall tents by clicking on the following links:

  • Wall Tent Buying Guide
  • Canvas 101
  • Wall Tent – What Size to Get
  • Wall Tent – What Size to Get How Many Rafters Do You Need for a Wall Tent Internal Frame? Choosing the Correct Size for the Internal Frame of a Wall Tent
  • Wood burning stoves for use with wall tents

wall tent frames

  • I’m just curious as to what folks are utilizing. I purchased a wall tent without a frame
  • The previous owner had it put up with trees
  • I am considering purchasing an angle kit and using 1″conduit for the frame (as many sites recommend) Was wondering if any of you guys were creative and came up with a better configuration! Please include photos if at all feasible! What website offers the most affordable angle kits? Thank you so much, Site Sponsor.

Re: wall tent frames

  • Take an old frame from one of those Canadian tire tarp tents (preferably one with straight walls), use the angles to your advantage, and trim the tubes to the length you want

Re: wall tent frames

  • Midland Tarps, located on Kingsway in Vancouver, contains all of the components you would want. Individually packaged and supplied at a low cost in both 1 1/4 and 1 3/4 sizes

Re: wall tent frames

  • It is possible to get custom wall tents and frames from one of our sponsors. In addition, the prices are fairly competitive. I also have one of their tents with the internal frame system, which is fantastic and quite simple to set up. Using lightweight aluminum for their poles and angles reduces the weight by nearly half compared to the weight of using steel or copper conduit. There will be no rust, no bother, and less weight. And don’t forget to donate to the site to be eligible to win a prize package that includes a premium wall tent, internal frame system, and stove! The following organizations have accepted me as a member: BCWF

Re: wall tent frames

  • You may get a set of angles for your conduit frame for for $117 + HST from VantagePoint Outfitters, another site sponsor on this page. “When you criticize somebody, you are not defining them
  • You are defining yourself.”

Re: wall tent frames

  • I made mine out of a piece of tubing and a welder! To me, their steaks, roasts, and burgers are excellent! Tom

Re: wall tent frames

  • My wall tent was purchased from Deluxe Wall Tents. Perry and the rest of the group are a pleasure to work with. It is far more difficult to obtain forgiveness than it is to obtain permission. The number “911” should be considered in the case of violent aggression, according to those who are of the rabbit people, it has been pointed out to us. Many others will be better served by putting their confidence in the number “1911.”

Re: wall tent frames

  • My hunting companion and I share a wall tent, which we use for protection from the elements. I must admit that I would not want to attempt to construct such structure out of trees and poles cut from the nearby forest. The price of the poles and angle set is fully justified in my opinion. mike

Re: wall tent frames

  • A 12X14 wall tent that I built myself out of 1 1/4 conduit and 1 in conduitpipe. It was a lot of effort and it’s heavy, but it’s easy to set up even by yourself. I also have all the wood poles for it, however metal poles are quicker to set up than wooden poles. Ron

Re: wall tent frames

  1. Vantagepoint provided me with an angle kit, which has made my life significantly simpler. 303 Crazy Farmer posted the original message. Yes, but your viewpoints are incorrect, and everyone in this room has to tell you so. Have a pleasant day

Posting Permissions

  • You are not permitted to start new posts or reply to existing ones. You are not permitted to submit attachments. You are not permitted to modify your posts.

The Rules of the Forum

Detroit Frame Tent Rentals

For many years, Wahl Tents has specialized in the rental of Frame Tents. Because they are constructed without the use of center poles, frame tents have a clean, unobstructed interior that may be quite useful for covering specific items such as bushes, pools, patios, and other similar structures. One other fantastic characteristic of a frame tent is that it is really simple to alter the side height from 7 to 10 feet and even farther. When it comes to anchoring their tents, frame tents offer greater flexibility.

Because there are no outside anchoring lines on a frame tent, you will also discover that it may be placed right up to a structure.

If you want an unobstructed interior and mobility, but theClearSpand does not quite match your budget, ourframe tents are a perfect alternative!

Interested in incorporating a Frame tent into your next event in Detroit, Michigan, or even across of state? Contact us now to learn more about how we can help! The following are some advantages of frame tents:

  • There are no impediments with center poles in the middle of them. Frame tents may be both freestanding and attractive in their design. It may be installed on grass, asphalt, concrete, or a deck
  • It is lightweight. They help to create an aesthetically pleasant atmosphere during the event. Tents with frames are adaptable.

You can simply put out a floor design using frame tents because of the advantages mentioned above. These tents are also quite sturdy and have the ability to cover a considerably larger area. We invite you to contact us or schedule an appointment with us so that one of our specialists can propose the best tent for you based on the sort of event you are planning, your requirements, the ground surface, and the available space. Frame tents are utilized for a variety of events in Detroit, Michigan, including business events, parties, and weddings.

Leave a Comment

Your email address will not be published. Required fields are marked *