How to Repair Tent Pole Elastic Cord (Re-thread) – the Easy Way
Determine the diameter of the cord that has to be replaced. When it comes to low-cost tents, this will often be approximately 2mm in diameter, which is not particularly sturdy or long-lasting. Depending on how large the opening diameter is of the pole, you may be able to utilize a thicker diameter than you originally planned. I increased the diameter of the cable on my tent poles from the standard 2mm to 3mm. The cable may be purchased on eBay for a reasonable price. I live in the United Kingdom and purchased 10 meters for around £3.
In order to set up a two-person dome type tent with two tent poles, you’ll need at least ten meters of space.
In an updated version of this post, I measured the original cable and discovered that it was half the length of the poles after they were completed.
Step 2: Find Your Threader
A threader, which you will need to obtain, will be required to feed the cord through. An nice metal threader was discovered within an old windshield wiper, which I was able to save. Consequently, when it is time to replace your windshield wipers, save them or borrow some from your neighborhood auto repair shop. The wiper blade assembly has two strips of metal that span the length of the wiper blade. You must remove these strips of metal from the wiper blade assembly. The greatest wiper blades are those from a saloon vehicle or a van since they have the longest blades available.
Please keep in mind that my photo displays a windscreen wiper, however it is too short.
Metal inserts are uncommon to be found in the lower-priced wiper blades.
Step 3: Join Threader to New Cord
It is now necessary to connect the threader to the new cable. This is accomplished by joining the threader and cable together using a butt joint and then fastening the junction with a very little quantity of adhesive tape. In this shot, I used one revolution of double-sided adhesive tape. Use only a little amount of tape, as too much will cause the threader to drag and cause it to stick to the inside wall of the tent pole.
Step 4: Remove Old Elastic Cord and Re-thread New Cord
Push the threader through the pole aperture after you have cleaned out the old cable from the poles. When it is sliding smoothly, slowly draw the threader through to the other end, where it should poke out the other end. Remember that if this is tough, it is likely that you have too much adhesive tape. Having passed through, pull the threader back through and continue to thread all the remaining poles.
I use up the old elastic cord because I’m a thrifty person. lanyards and neck cords can be made out of the old cord if necessary. I strung all of my USB storage sticks from the old cord that had frayed.
Step 5: Tension Cord and Tie Off the Ends
Trial and error is required to achieve the desired tension, so after threading the entire pole, experiment with your cord tension. The tension must be light enough to allow the poles to be pulled apart, yet firm enough to keep them together when threaded through the tent’s opening. The figure of eight knot is my preferred method of tying off the ends because it is a bigger knot that is also easy to alter. A more substantial knot at the end will last longer. You can then cut the cord after the tension has been reached to your satisfaction.
Step 6: Finished – Store Threader for Next Repair
You should have completed the repair of the tent poles by now. Remember to have your threader handy for when you need to repair your tent! I hope you have found this information beneficial. Thank you for taking the time to watch!
Be the First to Share
There are various little components in a tent that might fail, but these do not need the purchase of a completely new unit. Tent pole shock cords are susceptible to failure, deterioration, and brittleness with time, and finally loss of their elastic qualities. Your tent pole may no longer operate properly if the shock cord is no longer functioning properly. You may believe that new tent poles are required. Purchasing new tent poles, on the other hand, may be quite expensive, and there is a lot more affordable option.
It is simple to replace the shock cord in your tent pole; all you need are a few simple components and a positive mindset.
We’ll also talk about why shock cords are vital, as well as some preventative actions you may do to avoid more harm.
If you know how to mend a broken tent pole in the field, a broken tent pole in the field does not have to be a reason for panic.
What is a tent shock cord and why is it important?
Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.
Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.
Although you may use a non-elastic shock rope to hold your tent poles together in one piece, the elasticity is undoubtedly advantageous when putting together your wilderness shelter.
What you need to replace the shock cord in a tent pole
Make sure you have all of the materials you’ll need before starting to work on your tent repair. A replacement shock cord may be purchased at your local camping store, and there are several companies who sell shock cords online as well. You will require the following materials:
- The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
- Scissors or a sharp edge
- Measuring tape
- Sharpie or marker pen
- A lighter or matches to melt the ends of the wires Tape for masking
How to replace a faulty shock cord in a tent pole
The moment has come to get started on mending your shelter now that you have all of the equipment you need, as well as some new shock cable to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will see that your tent pole will come apart into its many components after the cable has been severed.
- Because it’s probable that the pole portions in the middle are similar, the end pieces where the rope is knotted are the most critical parts to avoid getting mixed up in the process.
- Perhaps you’ll need to remove your grommet pegs and then untie the remaining cable before you can continue.
- 2.
- Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
- Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
- If you are unable to use your previous cord as a reference, measure and mark the new cord to be approximately 8 inches shorter than the pole, or around 75% of its overall length.
- You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.
Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.
Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.
Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.
When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.
When you’ve reached the desired length with the string, tie a knot here to ensure that the peg is secure.
Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.
All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.
We’ve come to the end of our lessons on how to replace the shock cable inside a tent pole.
All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.
The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.
If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.
How to Repair a Shock Cord if it Breaks in the Field
A snapped or overstretched shock cable might make erecting your shelter more difficult if you’re already out on the trail during your camping vacation. If you want to repair the wire without having to replace the entire length, fortunately, there is a simple solution. However, while this is not a permanent solution, it will allow you to use your tent for a short period of time until you can replace the cord completely. If the cable hasn’t snapped, but rather has become too stretched out to go around your tent pole, there’s a simple solution.
- Then, draw the shock cable through the grommet peg until it is taught once again, and reattach it to the grommet peg.
- If the shock cord on your old tent pole has snapped, you’ll need to remove the pole using the steps outlined above to fix the problem.
- Remove a few inches of the cord’s elastic core on each side of the break, leaving only the braided sheath on the other side.
- The reason you need a thinner segment of cord to tie the knot is so that the knot will not become trapped in the poles and will be able to flow through freely.
Using string as a temporary replacement for a broken shock cord
If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can purchase a new replacement cable. Although this will not have the same elastic characteristics as real shock cable, it can be used as a temporary replacement until you can make more serious repairs. Keep this in mind when using this. All you need to execute this DIY patch is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a small number of supplies.
- Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
- Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
- This will make it much easier to thread the string back through the tent.
- Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
- Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
- Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.
When you’re finished, we recommend that you unfurl your poles to make sure there’s enough slack to pack away your tent properly. Any mistakes can be corrected by untying the end at a peg and making any required modifications.
How to repair a broken tent pole
The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a damaged tent pole as well as changing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.
- Purchasing a repair sleeve is a cheap option if your tent does not come equipped with one; you never know when you might require one.
- If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
- If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
- Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.
- Using duct tape, secure a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did previously.
Preventing damage to your tent poles in the future
If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.
When building your tent and connecting the tent poles, start with the central segment and work your way out from there.
This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.
You’ll be considerably more likely to prevent repairs and replacements in the future if you follow these few simple suggestions. If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.
Final Verdict:
It is occasionally required to replace the shock cord in your tent pole, but it does not have to be a difficult process. It is possible to save a large amount of money by making minor repairs and replacements to your camping equipment over time, and it is also considerably healthier for the environment. Learning how to execute these little repairs is simple, and more importantly, it will make you a more experienced camper. As an added bonus, watch this video for some further tent pole repair advice!
Tips for rethreading elasticated tent poles?
GreetingsElastic threaded through one of the poles of my family tent has been kapput. Do you have any suggestions for rethreading it? First, use a coat hanger to make a thin cord, then thread some shockcord through it. 3mm? It will be quite a ball pain because it contains 8 or 10 pieces. thanks In response to toiksander: Is it possible to use gravity and a safety pin on a thread to draw new cable through? In response to toiksander: I’ve done this a zillion times, and you’ll find that the shock cord can be pushed through the poles while giving them a slight twist as you do so.
- 1) Thread the elastic through the first pole and tie off one end of the elastic to keep it from coming out.
- 3) Tighten the elastic until it is taut, then clove hitch the tensioned elastic to something sturdy, such as a pencil.
- You may also insert a large safety pin into the elastic to prevent it from retracting farther.
- Repeat steps 3 and 4 until all of the threading is complete, and then make a knot in the elastic to prevent it from retracting.
- Gavin Post was modified at 14:31.
- That’s exactly what I was thinking.
- It is difficult to untie once the knot has been strengthened.
Take note of whether the shock cable is connected into a detachable end piece on the pole; this is typically very lightly cemented in place to prevent it from falling out.
Keep old tents free of poles and bring them in for repairs on a regular basis.
In response to Brownie: you may use a long length of bent wire to accomplish your goal.
Captain Paranoia received the following response: Heavier sea fishing nylon line was the only thing I was able to get through the fiberglass type pole I was using.
As long as you can attach the shock cord to the end of it, it will operate well, and it is simple to push through the pole.
The metal and huge pole sections have been covered by the majority of these.
Heat Make a larks foot and a seal at the end of the elastic, then stitch a portion of yarn that is longer than the pole as close to the end of the elastic as possible to ensure that the elastic pulls straight.
Keep the cordage and pole in a straight line to avoid damaging the pole end or abrading the yarn, which will cause it to snap (later) If you do, a consistent, solid pull will get you through to the finish line.
and then repeat the process If you still have the old elastic inside the pole, could you hook the new bit to the end of it and pull it through? In response toiksander: This subject has been archived and will no longer accept new posts in response to it.
How to repair tent pole elastic cord (Re-thread) – The Easy Way
Determine the diameter of the cord that has to be replaced. When it comes to low-cost tents, this will often be approximately 2mm in diameter, which is not particularly sturdy or long-lasting. Depending on how large the opening diameter is of the pole, you may be able to utilize a thicker diameter than you originally planned. I increased the diameter of the cable on my tent poles from the standard 2mm to 3mm. The cable may be purchased on eBay for a reasonable price. I live in the United Kingdom and purchased 10 meters for around £3.
- In order to set up a two-person dome type tent with two tent poles, you’ll need at least ten meters of space.
- In an updated version of this post, I measured the original cable and discovered that it was half the length of the poles after they were completed.
- Now you’ll need to find a threader to help you feed the cord through the hole.
- So, when it comes time to replace your windscreen wipers, keep these in mind.
- The wiper blade assembly has two strips of metal that span the length of the wiper blade.
- The greatest wiper blades are those from a saloon vehicle or a van since they have the longest blades available.
- Please keep in mind that while my photo displays a windscreen wiper, it is excessively short, and that NOT ALL WINDSCREEN WIPERS have metal inserts.
- It is now necessary to connect the threader to the new cable.
- In this shot, I used one revolution of double-sided adhesive tape.
UKCampsite.co.uk Camping and Caravanning Forums.
Forum | ||
Want to know what’s been going on? To see all new posts since you last visitedClick Here | ||
Information Forums | ||
Caravans and Caravanning(3 sub forums -Towing-Repairs-Statics) Touring caravan chat and advice, maintenance, storage, techincal advice, buying tips etc. Discussion on all makes of touring caravans including folding caravans | View ThreadsNew Topic | |
Camping and Caravanning EquipmentAdvice and queries on all camping and caravanning, and outdoor equipment from airbeds to fridges! | View ThreadsNew Topic | |
Motorhomes and CampervansMotorhomes and campervans – technical tips, maintenance, fulltimers, wild camping, friendly advice on all motor home topics. Plus self build conversions | View ThreadsNew Topic | |
Trailer Tents and Folding CampersDiscussions on Trailer Tents and Folding Campers of all makes. Buying advice, practical tips, maintenance, towing etc | View ThreadsNew Topic | |
Camping under canvas(2 sub forums -Tent Info-Backpacking) All things related to camping in tents – for tent buying advice see subforum. For campsite queries, and general chat please use the appropriate forum. Site reviews must be posted in the campsite search, not here. | View ThreadsNew Topic | |
Other Outdoor Activities, Days Out and Places to VisitDiscussions on walking, climbing, cycling, fishing, sailing etc. Ideas for days out and places to visit. Please use the campsite forum for site information / recommendations | View ThreadsNew Topic | |
Campsites and Caravan Parks | ||
Campsites and Caravan Parks in the UKCamp Site feedbackadvice for sites and parks in England, Scotland, Wales and N Ireland.Please search our campsite listings for reviews before posting. | View ThreadsNew Topic | |
Caravanning and Camping AbroadAdvice and discussion on camping and caravanning in France, Spain, Holland, Italy, and the rest of Europe and beyond | View ThreadsNew Topic | |
Trip Reports and PhotosIf you wish to post photos and reports from your camping or caravanning tripsplease remember to leave yourreview in our campsite listingsfirst!, and only then use this section to leave your trip report | View ThreadsNew Topic | |
Meeting up and Getting Together | ||
Meeting Up and Getting Together(1 sub forum) If you fancy meeting up with other members post here! When starting a new thread please ensure you include the location / area in your subject line | View ThreadsNew Topic | |
General Discussion | ||
Life in GeneralSubjects not covered in other forums. If you want to just chat, or say hi please use the Chat forum. Please avoid anything referring to politics and religion | View ThreadsNew Topic | |
Chat, Games, Trivia etc(1 sub forum -Jokes) Please post chat with other members here.Jokes to go in the subforum please. | View ThreadsNew Topic | |
Competitions, News and Website Feedback | ||
Competitions, Industry News and Website UpdatesDetails of all the latest UKCampsite.co.uk competitions and website updates. Plus News and reports related to caravanning and camping and the leisure industry. | View ThreadsNew Topic | |
Feedback, Ideas and Help Requests related to this websiteFeedback and suggestions and help requests about this website and forum only | View ThreadsNew Topic |
Broken elastic on tent pole – how to repair? – CampingForums
Thank you for providing the link! thevegasdesertfox wrote the original post Post a Comment Greetings, pgwerner. They (the tent manufacturers) want you and everyone else to go out and buy a new tent, or to stop camping altogether if you already have one. Yes, that is the sense I received from the conversation. Please report back if it works and tell us how you accomplished it so that everyone may benefit from your efforts. It is possible to snap nylon strapping into tent poles, although it has never happened to me.
- Thank you for your enquiry, and I look forward to hearing from you.
- Actually, I took a closer look at it and was able to come up with an easy resolution for the problem.
- The shock cord is linked to the screw/end of the screwdriver with a simple knot on the inside.
- The tent pole is snapped back together once more.
Vegasdesertfox, how about that? Right now, I’m preparing for a trip to Red Rock Canyon (the California one), Death Valley, and Interstate 395 in the coming weeks. What a beautiful country! In any case, thank you once again for your guidance.
How To: Replacing the cord in your tent poles
17th of July, 2020 Tension is applied to tent poles by the use of shock cock, an elastic string that aids in the snapping back together and maintaining the form of the tent poles. It is possible for the elastic in the shock cord to degrade with time, causing the cord to sag and, eventually, making your poles very difficult to use and practically impossible to use. A replacement tent pole set may be rather expensive, so if your poles are still in good condition, it is significantly more cost effective to simply change the cable.
Because these tent poles are from my Sierra Lightning II FL, and because no two tents are exactly alike in terms of size, the quantity of shock cord you’ll need may vary depending on your tent.
When determining the quantity of cord to purchase, I find it better to just purchase the same amount as your pole dimensions to allow for some margin of error.
Shock cord is available at most respectable camping stores as well as on the internet.
What you’ll need:
- Shock cord (with a diameter equivalent to your present shock cord and a length sufficient to cover the length of your poles)
- Scissors with a good edge
- The following items are required: Tweezers and wire (you may use wire from a coathanger, or check out what you can get at craft stores or Bunnings if the wire has to be thinner to fit through the ferrule)*
- A helping hand
This is applicable to poles that have a stopper that is inverted in the ferrule rather than a pull or screw-out type stopper. You may also watch a video on YouTube that shows you how to replace the cable on your tent pole. Tent poles are being unfolded.
Step 1
Prepare your tent poles by laying them out. Because you’ll be unthreading them, you’ll want to do this in a place where you have lots of space to keep them organized.
Step 2
The end stop at the end of your tent pole should be removed. Removal of the end stopper* If your tent poles are the older design with a stopper or washer in the ferrule, you’ll need to take the knot out of the stopper with tweezers and cut or untie it to allow the new rope to pass through and out of the way. When you reach to the other end, you’ll have to repeat the process in the opposite direction. The difference between poles with a pull-out end stopper and poles with a washer is seen in the diagram to the right.
Step 3
Untie the string or cut it at the end stop and set the end stop on the ground. As you begin to remove the old shock cord, make sure to arrange your tent poles in the same position as you did previously. Taking the cable out
Step 4
Obtain your new piece of shock cable at this time. I’ve pre-measured my and indicated the place where I want it tensioned to, but I’m not going to cut it yet since I find it simpler to tie and cut it once it’s already been tied. Begin with the first piece of pole and pull your shock cord all the way through to the stop at the end. Then tie a knot around the end stop to keep it in place. INVERTED STOPPER: If you’re working with an inverted stopper, you’ll want to make sure your wire is prepared.
When you reach to the end, tie a strong knot large enough to prevent the shock cord from passing through the hole again. Then pull the shock cable all the way through to secure it. Feeding the wire through the washer is a simple process. Pulling the shock wire through the washer is a good exercise.
Step 5
Now that the end has been attached, draw the shock cord through the remaining sections of poles, being sure to retain them in the same sequence as they were originally put out.
Step 6
Once you’ve reached the end, tighten the cord until you see a mark on it, then secure it to the end stop, making care to maintain the proper amount of tension in the cable. Before cutting the rope, I prefer to double-check that the tension is correct. In order to keep the poles together, the shock cord should be tensioned just enough to keep them together, but not so much that the shock cord is over-strained when the poles are folded. STOPPER WITH AN INVERTED POSITION: Before you get to the end, you’ll need to take a break before the final stretch of poles is reached.
Now, re-grab your wire and push it through the final length of pole, starting at the other end and working your way toward the end stopper.
Return to the other end of the stopper and undo the knot on your second-to-last piece of pole section and fasten it to the wire.
Adjust the tension as needed, then finish with a knot that is large enough to catch on the hole.
Step 7
When you’re satisfied with the tension, cut the cord neatly and tuck the end back inside the pole sleeve with the end stop, securing the end stop with a screwdriver. The shock cord may require assistance in this area since it is difficult to cut and is much simpler to cut when someone else is tensioning it for you.
How to Repair Snapped Camping Tent Pole Threading
Because the most majority of campingtent polethreading is made of elastic, it is susceptible to becoming weak over time, resulting in it breaking or snapping. The inconvenience of this situation may be excruciating, especially if you find yourself stranded in an area where there are no readily available tent repair kits. Rather of ordering a pricey kit in the mail or taking your tent to a camping specialist to be repaired, you can replace snapped camping tent pole threading fast and easily by following these simple instructions.
Step 1 – Finding Some Pole Elastic
Finding new elastic will be necessary in order to correctly fix the threading on the pole. Another option is to just purchase a sufficient pack of pole elastic from a camping supply store like as Millets, which is less expensive than purchasing a pole threading kit, but it is more time consuming and requires more effort. This elastic will be appropriate for threading onto a pole, and you’ll find that you can obtain a rather large pack for a reasonable price, and you’ll most likely have some money left over after paying the shipping.
Step 2 – Prepare the Pole
Once you have acquired your elastic, you will need to ensure that it is acceptable for insertion into the pole before proceeding further. There are two options for accomplishing this. Purchase a wire threader, which can be attached to the end of the elastic and used to thread it through the pole, or singe the end of the elastic to make it harder by using a flame to make it tougher.
As a result, you will have enough strength in the elastic to be able to thread it through the hole. Mark off the length of the old elastic using a felt tip pen, and then measure and mark off the same length on the new elastic. Cut to the appropriate size.
Step 4 – Replace the Elastic
As you hold the pole erect, insert the elastic band through the pole’s opening. Make a knot on the end of the elastic and draw it through the pole until you reach where you marked with a felt tip pen. Tie another knot in that spot after you are through threading your camping tent pole. Once the elastic is threaded through all of the tent poles that you will use, proceed as usual with the project.
Help! My tent is broken! – How to fix your tent and repair poles
As a result, your really costly tent is shattered or ruined. What options do you have? We demonstrate a few approaches to assist you in resolving the issue. Any family tent represents a significant financial investment, and when catastrophes occur, such as a bent tent pole, you may be faced with the risk of having that investment completely wiped out from under your feet. Here’s a brief list of objects that have broken, along with the many alternatives you have for repairing or replacing them.
Fixing a bent tent peg
In all seriousness, you are going to have bent tent pegs, especially if you are using the standard pegs that came with your tent. Seriously?!? These tent pegs are very inexpensive and will quickly bend if not handled properly. While it is possible to construct a jig to straighten them, doing so is not recommended. Replacement tent pegs are inexpensive and readily available. However, you should be updating your tent pegs regardless of whether you are camping or not. Read this post to find out what kind of tent pegs you should buy.
Replacing a snapped guy line
Guy lines are generally rather robust, and I haven’t come across one that has snapped yet. However, if this does happen to you, don’t be concerned, because replacement guy lines are readily available online.
Fixing Leaking Tent Seams
What was once a completely dry tent may begin to bleed water via a seam due to a leak. This can occur for a variety of causes, including:
- The waterproof coating or seam sealant has become ineffective
- The seam has been stretched beyond its breaking point, and the seal has been compromised. A previously undiscovered fault has just recently become a problem as a result of a change in wind/rain strength and direction.
You should also double-check that the seam is indeed leaking, as moisture in a tent may often give the appearance of a leak. You could even find yourself with a pool of water in your tent if your tent hasn’t been properly ventilated before you set up camp. An additional consideration is that certain poly-cotton or canvas tents may have somewhat leaky seams the first time they are used, since the materialstitching has not yet settled (well, this is what one manufacturer reported anyway). It is simple to repair a little leaky seam.
If you want a more permanent solution, you may acquire some tent seam sealer instead.
Click here to read an article on how to avoid a leaky tent and how to stop the tent seams from leaking.
Waterproofing Your Tent
It is also possible to seek treatment for leaky seams if you believe that water is no longer running off the tent material as it used to, which is something you should investigate further. Even the soapy combination used in your child’s bubbles might be a source of concern for them. Was it ever brought to your attention that laundry detergent might destroy the waterproof covering from your tent? A problem might arise even from the soapy combination used in your child’s bubbles. You may purchase a spray-on waterproofer, which is a convenient item to have on hand when camping.
Although it is considerably more difficult and time-consuming to apply to the entire tent (with the added danger of making it appear ‘patchy’), there are some firms that will do this for you, as well as thoroughly cleaning the tent to make it look as near as possible to its original condition.
Fixing a Bent or Broken Tent Pole
Now, the answer to a broken or bent tent pole is highly dependent on the type of tent pole in question, as well as the location and severity of the damage.
Replacing ‘bendy’ Fibreglass Tent Poles
If your tent is equipped with flexible tent poles (which are normally constructed of fiberglass or a composite material and are typically black or grey in color), they are the easiest to repair and replace.
1. Simple DIY Tent Pole ‘gaffa’ Repair
Most of the time, these sorts of poles are capable of splitting, exposing the inner elastic that binds the various pieces together. The best in-field fix for this is a simple piece of gaffa or duct tape. We’ve done this previously, and the tape really lasted for a few more seasons after that. When you go camping, always remember to bring some gaffer tape with you.
2. DIY Replacement Section
You may also purchase replacements, which can be either full poles or simply a portion of a pole. If you only wish to replace a segment of the pipe, take measurements of the width and diameter. After that, you may find a replacement in the proper size. To re-thread the elastic through, you will need to dismantle the pieces of the pole that were before the damaged pole. Some replacement kits have a convenient pull through that is handy for threading the elastic line through the tent pole.
Replacing Steel Tent Poles
It is possible to straighten a bent steel tent pole if it is a straight portion and it has not been bent too far out of shape; however, this is not recommended. But if that isn’t possible or if the tent pole is formed, it is preferable to take it to a metal craftsman with a non-bent pole that is identical to the bent pole. The metal worker will be equipped with equipment that will allow him to quickly return the pole to its original shape, as well as the ability to heat the pole if necessary to avoid straining the metal.
2. Replacing the bent pole section
When it comes to poles that can’t be replaced, your options are quite restricted. There are occasionally some replacement poles available for straight portions, however most steel tent poles are made to a specified form for the tent type that you have purchased.
3. Contact the retailer
The first thing I would suggest is that you contact the store where you purchased it, and if that is unsuccessful, you should contact another retailer who carries your brand of tent. Some merchants may have a few extras on hand, or they may have some old stock that they are willing to sell you. Of course, depending on the part, this may entail a modest premium over the standard rate.
4. Contact a spares supplier
Tent spares are only available from a few providers that offer a repair service. One such service isTentSpares.co.uk, a specialised outdoor repair service such asScottish Mountain Gear, which is one example of this type of service. My own experience with their service is limited (thank goodness! ), but I am aware of a few other people who have had positive experiences with it.
5. Contact the Manufacturer
It is uncommon that contacting the tent maker is effective. They send a lot of goods out to shops and don’t keep spares on hand, and they don’t keep stock on hand to assist consumers directly. unless they sell tents directly to the public, in which case there’s a chance they’ll have some on hand. You may also anticipate that the manufacturer will not be able to repair a single tent pole but will only be able to deliver (sell) you a whole set of tent poles because this is what is left over from their manufacturing run.
This might end up costing you almost as much as purchasing a brand new tent.
6. E-Bay
For popular tent models, there is a considerable second-hand market to choose from. While the expense of purchasing a second-hand version of your tent for the purpose of replacing a pole may seem extravagant, it may still be less expensive than other alternatives. Keep an eye out on the second-hand market for any more tents that may be available as spares. Somebody else’s tent may have been damaged, but it may have been in a different place, and you will be able to pick it up for a far lower price.
Repairing a Ripped Tent
A ripped tent does not necessarily imply the end of the tent.at least not if the rip is not too severe. When you are camping, gaffa tape will come in handy if you have a little rip. In case of an emergency, you may also purchase tent repair tape to use in the meanwhile. Cover the area with a tarp if you need to make an emergency repair to a larger rip — you do have a tarp, don’t you? (read this). Some tents include some repair cloth as well as some glue for minor repairs (and a few with a self-adhesive patch).
If your tent does not come with a patch, you can purchase one from a store; however, the color of the patch may not match the color of your tent.
If you require anything further, you may need to call a local tent repairer (whom your local camping shop may be able to recommend) or look into purchasing a used tent.
Useful items for DIY Tent Repairs
Here are some tools and supplies you may use to repair your damaged tent on your own. GorillaTapeIdeal for making quick repairs in an emergency. Outwell The Luminous Guy Line is a line of clothing that is brightly colored and stands out from the crowd. VangoGuy Line is a transportation company that specializes on vangos. There are a variety of colors to choose from. OutwellDurawrap These are available in a variety of sizes. Outwell Steel Pole with a Straight Base These are available in a variety of sizes.
- VangoFibreglass Pole is made of fiberglass.
- McNettSeamSure For the purpose of repairing leaky seams McNettSeamgrip It is used for mending seams that have fallen apart.
- Patches of McNett’s tenaciousness For bigger holes in your tent, use a tent sealant.
- NikwaxTent It is possible to purchase them in either spray-on or bigger sizes.
- Photos courtesy of Thomas Guest.
Get the Family Camping Planner
You will receive the family camping planner once you have entered your name and email address.
Make Your Old Tent Like New
picture courtesy of joytstockphoto “data-image-caption=”” data-medium-file=” data-large-file=” loading=”lazy” data-large-file=” data-medium-file=” data-large-file=” src=” alt=”istockphoto/joyt” width=”663″ height=”444″ width=”663″ height=”444″ srcset=” 663w, 300w, 344w, 550w” srcset=” 663w, 300w, 344w, 550w” sizes Equals sizing” (max-width: 663px) 100 watts, 663 pixels “> The following is an example of a formalized formalized formalized Whenever a cherished tent is nearing the end of its useful life—especially when you don’t have the time or money to invest in a new one—it might be difficult to let go of it.
In spite of the fact that you will need to invest a little amount of time and money, you may delay the big-ticket price with these five simple fixes and improvements to your existing one.
If your tent has only a minor odor, recoating it will almost certainly eliminate the musty odor as well as the stink.
If there aren’t many cracks and peeling in the waterproofing, you may revive your tent by using a wash-in, brush-on, or spray-on solution after you’ve done the pre-wash.
Set up the tent and apply a seam sealer to glue all of the seams together.
This adaptable finish will make your tent seem as good as new in a short amount of time.
This is one of the most common ways that poles break.
Simple cable shortening is another option that is considerably more easier to do than the first.
For each new shock cable you use to replace the old one, you’ll need to knot a firm leader cord to the end of the new shock cord so that it can be threaded through the pole.
According to the manufacturer, this increases the ability of segmented poles to “snap together” and increases the endurance of the cable.
With your hands still gripping the slack rope, tighten it until it is taught (at the open end), making sure to keep all of the pole segments together.
The length of the cable should be around 65 to 75% of the total length of the pole.
Simply said, that’s all there is to it.
This is a simple problem to solve.
Upgrade What’s at Stake for You?
Get rid of them because today’s stakes are far lighter and more efficient.
A variety of environments can be accommodated by Y-beam, hex, or three-sided aluminum stakes, which are the most versatile.
Affectionately known as “backpackers,” they are devoted to ultra-light travel cot titanium or carbon fiber-core aluminum stakes available in bolt, needle, and peg forms.
Even when the tips are coated or painted, they have a proclivity to dissipate into thin air without a trace.
Upgrade the InteriorLED tent lights are not only entertaining, but they also assist you in navigating the interior of your tent without disturbing the hikers in the tent next door.
You may gain rapid and uncluttered access to your equipment, gadgets, and clothing by including a storage crib or gear line in your tent’s interior.
It is possible to attach lines with hooks and Sbiners in a vertical orientation to maximize storage and minimize wall space, or you may hang them horizontally if you need quick, eye-level access to your stuff.
