How To Restring Tent Pole

How to Replace a Tent Pole Shock Cord

The elastic shock cord on your tent poles has deteriorated and has become brittle, making it no longer flexible. Given that new poles can cost up to $100 or more, why not simply replace the cord, which costs less than ten percent of the price of new poles? It’s been years since I’ve used my North Face Rock 22 two-person tent (which has two identical poles), and the elastic cord within the poles has become brittle and no longer retains its flexibility. I had purchased the tent brand new for around $200, and replacement poles were going to cost an additional $150!

I just needed 30 minutes and a pint of beer to get my tent poles back to their original condition!

You’ll need at least the whole length of all of your poles combined to complete the task.

a pair of scissors or a knife Sharpie or Marker for Measuring Tape Matches or a lighter are recommended.

Step 1: Cut the Cord and Remove the Grommet Pegs

Take a deep breath in and out. Pulling two parts of the pole apart and cutting the rope will do this. This will cause the pole to divide into its distinct parts (Mine has 8 sections per pole, and only the two end sections are different, so I made sure to keep those separate). Remove the peg from the pole end and you should be able to see the standing end of the cord, which has been knotted and linked to the peg. Because my pegs were threaded, I had to detach them from the pole sections in order to use them.

Step 2: Measure Your Pole(s)

Following that, you’ll want to take measurements of your poles so that you can determine how long your rope should be. Because my tent has two poles that are exactly the same length, I only had to measure once. If you have many poles of varying lengths, you will need to repeat this step for each pole in your set. Measure the length of your pole from end to end; this will be the length of your rope when it is fully stretched. My experiments with the elasticity of the cable led me to the conclusion that for every foot of relaxed cord, I would receive 1′-4 of length “because of a stretched chord To get the final length (the length of the pole, hence the ultimate stretched length), we must multiply it by 75% of the original length.

Take the length of your pole in inches and multiply it by 0.75.

My poles are 152 inches in length, hence my measurement is as follows:152 inches * 0.75 inches = 114 inches” This is the spot where I put my relaxed chord marker.

Please keep in mind that you should not cut the cord just yet! It is quite difficult to feed a 114″ cable into a 152″ pole because of the length difference. Inquire as to how I know this.

Step 3: Thread Your Peg and Knot the Cord

Feed the standing end of the cable (the end that is marked with a ‘zero’ on the tape measure) through the hole in the grommet peg and secure it with a rubber band. Draw the thread through a basic binding knot about 2 inches from the end and tighten it. Your peg should now be in the middle of the knot and the long end of the rope, as seen below. In order to avoid tripping, feed the cord through the first part of pole and continue until all portions are attached to the cord. Check to see that the pole portions are aligned appropriately so that they will fit together as intended before continuing (male end toward female end for each joint).

The long end of the cord should be stretched so that it reaches the mark you created earlier while the pole pieces are joined in the manner in which you would build the tent.

In this stage, the pole should be beginning to take form.

Step 4: Cut/Singe the Cord and Insert the Pegs

Remove the cable from the machine, leaving around 2 inches of standing end. Make a singing sound with the lighter or matches at the end of each string (on both ends of the pole). Fold the cord over upon itself and put the standing end of the cord into the pole to complete the loop. Incorporate the knot into the pole. Insert the peg into the pole with the threading needle. Each pole should be treated in the same way.

Be the First to Share

There are various little components in a tent that might fail, but these do not need the purchase of a completely new unit. Tent pole shock cords are susceptible to failure, deterioration, and brittleness with time, and finally loss of their elastic qualities. Your tent pole may no longer operate properly if the shock cord is no longer functioning properly. You may believe that new tent poles are required. Purchasing new tent poles, on the other hand, may be quite expensive, and there is a lot more affordable option.

It is simple to replace the shock cord in your tent pole; all you need are a few simple components and a positive mindset.

We’ll also talk about why shock cords are vital, as well as some preventative actions you may do to avoid more harm.

If you know how to mend a broken tent pole in the field, a broken tent pole in the field does not have to be a reason for panic.

What is a tent shock cord and why is it important?

Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.

Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.

Although you may use a non-elastic shock rope to hold your tent poles together in one piece, the elasticity is undoubtedly advantageous when putting together your wilderness shelter.

What you need to replace the shock cord in a tent pole

Make sure you have all of the materials you’ll need before starting to work on your tent repair. A replacement shock cord may be purchased at your local camping store, and there are several companies who sell shock cords online as well. You will require the following materials:

  • The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
  • Scissors or a sharp edge
  • Measuring tape
  • Sharpie or marker pen
  • A lighter or matches to melt the ends of the wires Tape for masking

How to replace a faulty shock cord in a tent pole

The moment has come to get started on mending your shelter now that you have all of the equipment you need, as well as some new shock cable to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will see that your tent pole will come apart into its many components after the cable has been severed.

  • Because it’s probable that the pole portions in the middle are similar, the end pieces where the rope is knotted are the most critical parts to avoid getting mixed up in the process.
  • Perhaps you’ll need to remove your grommet pegs and then untie the remaining cable before you can continue.
  • 2.
  • Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
  • Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
  • If you are unable to use your previous cord as a reference, measure and mark the new cord to be approximately 8 inches shorter than the pole, or around 75% of its overall length.
  • You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.

Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.

Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.

Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.

When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.

When you’ve reached the desired length with the string, tie a knot here to ensure that the peg is secure.

Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.

All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable inside a tent pole.

All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.

The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.

If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.

How to Repair a Shock Cord if it Breaks in the Field

The moment has come to get started on fixing your shelter now that you have all of the equipment you need, as well as some new shock cable to replace your old, failing ones. Your tent will look like new if you follow our instructions. The first thing you should do if your shock cord is still intact is to split the tent pole in half and use scissors to cut the shock cable that is hidden within. You will see that your tent pole will come apart into its many components when the cable has been severed.

  1. Given that it’s likely that the pole portions in the middle are all similar, the end pieces where the cable is fastened are the most critical parts to avoid being confused with one another.
  2. Some grommet pegs may require unscrewing before the remaining cord may be untied.
  3. The length of the cord that will be used to replace the old, broken one must now be determined.
  4. If you want to know the entire stretched length of cord you’ll need, measure your pole from end to end.
  5. Don’t cut the rope until you’ve marked it with a marker pen the length you’ll need.
  6. If you are unable to use your previous cord as a reference, cut a new cord that is approximately 8 inches shorter than the pole, or around 75% of the overall length of the original cable.
  7. Due to the fact that you’ll be threading the line through the tent poles, you’ll need to cut the cable a little longer than the tent poles.

Finally, start threading your tent pole by taking the longer end and threading it through each segment of the pole.

Make certain that the cords are threaded in the right direction, from male to female, or else they will not fit together when you’re through sewing.

Build the tent pole so that all of the components are joined together, just like you would while pitching a tent.

While the free end of the new shock cord should be passed through the peg at this point, the cord should not be fastened on at this time.

Continue to apply strain to the shock cord until you see the mark you produced previously.

5.

Use a lighter or a box of matches to singe the end of the cord so that it does not tear or unravel.

With everything tucked away and reassembled, there should be no evidence of the shock cord outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable within a tent pole.

The wear and tear on all camping equipment is inevitable, although it is rarely essential to replace it.

This is an excellent strategy to utilize if you’re at home and need to do some repairs, but what happens if your shock cord breaks while you’re on a camping trip?

If you don’t have an extra length of tent pole shock cord on available, keep reading to learn about potential alternatives to this procedure.

Using string as a temporary replacement for a broken shock cord

If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can purchase a new replacement cable. Although this will not have the same elastic characteristics as real shock cable, it can be used as a temporary replacement until you can make more serious repairs. Keep this in mind when using this. All you need to execute this DIY patch is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a small number of supplies.

  • Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
  • Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
  • This will make it much easier to thread the string back through the tent.
  • Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
  • Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
  • Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.
  • Any mistakes can be corrected by untying the end at a peg and making any required modifications.
See also:  We Tent To Trust Speakers Who Have A Certain Amount Of Ethos

How to repair a broken tent pole

The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a damaged tent pole as well as changing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.

  1. Purchasing a repair sleeve is a cheap option if your tent does not come equipped with one; you never know when you might require one.
  2. If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
  3. If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
  4. Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.

Using duct tape, secure a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did previously. Duct tape may be used to cover the whole surface; just make sure your repair is secure before proceeding.

Preventing damage to your tent poles in the future

If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.

When building your tent and connecting the tent poles, start with the central segment and work your way out from there.

This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.

If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.

Final Verdict:

For those of you who have had to make a repair to a tent pole shock cord and would like to prevent having to do so again in the future, we have some suggestions for maintaining and extending the life of your tent poles. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment like loose soil, gravel, or mud. When your poles are folded up, there are apertures into the empty interior that you may see through them. It’s important to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and break again.

When assembling your tent and connecting the tent poles, start with the central piece and work your way outwards from that point.

Thus, the elastic shock cable within will be put under less strain, which will lessen the likelihood of breakages and replacements being necessary.

If you’re willing to put in the effort to make a few minor repairs, resting on your camping trip will be much more enjoyable.

How do I repair the shock cord at the center of my pole?

This page was last modified on Tuesday, March 9, 2021 at 10:26 a.m. If you have a shock cord that has become stretched out, gone slack, snapped, or is just worn out and in need of replacement, you have come to the proper spot to get it replaced.

This is really a fix that can be completed rather fast and simply at home with little tools. Quest Outfitters carries shock cord, which can be obtained at most hardware stores, outdoor retailers such as REI and Moosejaw, and sporting goods stores.

DIY Shock Cord Replacement

You will need 1/8″ thick shock cord that is around 1-2 feet longer than the length of the complete pole for each pole (for example, if you have a 10ft pole, obtain roughly 12ft; others think a 34% ratio may be preferable.).

  1. The shock cord will be wound in a knot once the end tip has been removed (either on a washer or on the end tip of the pole). Cut the knot and you’ll be able to remove the shock cord with ease. The most essential thing to remember is to remove the pieces of each pole in the same sequence that you removed them. After you have removed the old shock wire, you will be ready to thread the new shock cable on each pole. Remember to string them back together in the same sequence. Gently push the shock cord through the entire length of the pole, then tie it off at one end (either with a simple knot or with a loop attached to the pole tip)
  2. Then, to tension the shock cord, pull out about 25% of the total length of the pole in slack (for a 10ft pole, pull out 2-3ft), and tie it off at the pole end. After that, you may check the tension and make any required adjustments
  3. The pole parts should softly seat themselves. Keep in mind that this is not an exact science, so use your best judgment and common sense while making decisions. Remove any extra shock cable after that, and you’re finished

Here’s a link to a fantastic tutorial from REI that goes over the process of fixing tent poles and includes a part on how to restring shock cord at the base of the pole: Fixing a Tent Pole (with Pictures) Did you find it to be of assistance? Yes NoFeedback is not required.

How To Restring Tent Pole

To complete this project, you’ll need a shock cord (1/8′′ or smaller). You’ll need at least the whole length of all of your poles combined to complete the task.

Can you fix a broken tent pole?

A pole repair sleeve is the quickest and most convenient method of repairing a damaged pole. This little tube, which is also known as a splint, is frequently included with your tent. If you don’t already have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not move about too much.

Do tent poles need the elastic?

Regarding a gear concern, the “string” that runs through the tent poles The shock cable may be removed and thrown away with less effort and weighs less. It is completely ineffective.

How do I put up a tunnel tent by myself?

How to Set Up a Tunnel Tent (with Pictures) Prepare the location of your tent. Locate a location that is as level as feasible. The tent should be unfolded. This is where having a groundsheet or tarp comes in in, especially if the weather has been very drizzly. The tent should be unfolded. Tent poles should be inserted. Ensure that the tension in the poles is taken up. Raise the tent to the proper position. Prepare the tent by pinning it down. Set up the inner tents on the ground.

What is a tent ferrule?

When two composite rods or tubes are joined together, ferrules are utilized to link them together. They also make it possible to employ shorter carbon or fiberglass rods or tubes, as well as to construct and dismantle your finished product, resulting in a smaller container for transportation purposes.

How do you cut a Fibreglass pole?

Align the rear edge of the fine-toothed hacksaw blade with the pencil mark using a straightedge and a level. Allowing the hacksaw to slowly move toward you and then away from you will allow you to cut through the fiberglass stick. Cutting should be continued until the fiberglass stick is divided into two halves. To finish the cutting operation, remove the masking tape off the fiberglass stick and discard it.

What do you do with a broken tent?

Continue to: Repurposing Is the Most Effective Option. Recycle your tent by purchasing it from an online retailer. At a yard sale or garage sale, you may recycle your tent. Make Use Of A Local Recycling Center To Dispose Of Your Tent. Thrift stores are excellent places to recycle your tent. Don’t throw your tent in the trash or recycle it. Make Use of Your Old Tent for Indoor Recreation.

Can one person set up a 4 person tent?

Easy to assemble, the Core 4-Person Instant Tent accommodates four people comfortably.

As the name indicates, it is practically instantaneous. To set up the tent, all you have to do is unfold it and extend the poles until they snap into position. It is quite simple, even for novices, and takes just a few minutes to complete.

Can I cut a fiberglass tent pole?

Easy to assemble, the Core 4-Person Instant Tent can accommodate four people in total. As the name implies, it is practically instantaneous. There’s nothing more to it than spreading out your tent and stretching the poles until they snap into place. You can accomplish it in minutes and it is quite simple, even for novices.

Why do my tent poles keep breaking?

Strong winds, poles that have been weakened with age, and inexpensive materials are all potential causes—and occasionally it’s just plain old wear and tear.

Do they sell tent poles?

A set of two REDCAMP Aluminum Tarp Poles that are heavy-duty and adjustable, measuring 35 inches to 90 inches (75″ to 86 inches) in length, and are designed for use with tarp canopies and awning shelters.

Do graphite rods break easily?

The fact that they are as robust as nails does not mean that they are readily broken. However, don’t tempt fate by being disorganized when it comes to arranging your fishing rods.

How do you cut fiberglass without splinters?

Place masking tape along the cut line of a panel, mark the line on the tape using a pencil, then saw through the tape to reduce chipping and splintering. Inside corners cut in a panel should be rounded to prevent a fracture in the completed item as a result of a sharp corner.

How do you dispose of old tents?

In fact, there are 15 innovative methods to reuse an old festival tent that you should check out. Keep an eye on your plants. Make use of natural elements in your landscape. Make your own gazebo out of wood. Make some bags. Ponchos should be made. Fly a kite in the air. They can be used as groundsheets. Protect your upholstered furniture with these pads.

Can one person put up a tent?

There is absolutely no need to be afraid. Despite the fact that dome tents appear to be tough to put together by oneself, they are actually one of the simplest tents to put together! Installing a dome tent is now easier than ever before if you have a recent model on hand.

Can you fix a tent pole with duct tape?

In a pinch, duct tape may be used to repair a damaged tent pole, but this is only a temporary remedy and should not be relied upon. Using duct tape, just wrap the break until it is strong enough to hold the weight of your tent. With order to provide more support, you might apply an improvised splint before covering the break in tape.

What’s the easiest tent to put up?

What is the quickest and most straightforward tent to erect by yourself that we recommend? For Backpacking, the best option is the Teton Sports Instant Tent (1/2 Person). Core Instant Cabin Tent for up to 9 people. The best all-around tent. The Vango Dart Pop Up is a little inflatable boat that can be taken anywhere. Tent for three people. Wenzel Klondike is a fictional character created by author Wenzel Klondike. Tent for eight people. 2/3/4/6 Person Coleman Sundome Dome Tent (Coleman) Vango Airbeam Odyssey Air 500 Villa Tent is a Vango Airbeam Odyssey Air 500 Villa Tent.

Can you buy the top half of a fishing pole?

In most cases, getting a new rod will be more cost effective than repairing an old one, unless you have a heritage rod or need to have the rod butt fixed.

There are a plethora of various types of “2 part fishing rods” available. It is preferable to get a new rod that is suitable for your planned application. I hope this has been of assistance.

What are flexible tent poles made from?

Tent Poles Made of Glass Fiber Because of the inexpensive cost of glass fiber, it is a common choice for less budget tents due to its durability. Because of its flexibility, a tent bends with the wind rather than standing hard against it, allowing it to shed gusts. When you are experiencing something for the first time, it might be a little unnerving.

See also:  What Is The Easiest Pop Up Tent

How do you remove a ferrule from a tent pole?

Place the pole in a vice and heat the ferrule’s tip with a heat gun, grabbing the ferrule with pliers as it heats up, and turning it to check if it starts to move. It is important not to overheat the pole since this will cause it to burn.

How To Restring A Tent Pole

Place the pole in a vice and heat the ferrule’s tip with a heat gun, grabbing the ferrule with pliers as it heats up, and turning it to check whether it starts moving. Take care not to overheat the pole as this may cause it to burn.

Can you fix a broken tent pole?

Place the pole in a vice and heat the ferrule tip with a heat gun, grabbing the ferrule with pliers as it heats up, and turning it to check if it starts to move. It is important not to overheat the pole, since this will cause it to burn.

Can one person put up a tent?

There is absolutely no need to be afraid. Despite the fact that dome tents appear to be tough to put together by oneself, they are actually one of the simplest tents to put together! Installing a dome tent is now easier than ever before if you have a recent model on hand.

Are all tent pole sections the same length?

Fibreglass tent poles come in millimeter-measured lengths alone, thus if you measured 3/8′′, the 9.5mm pole size would be the correct choice. A number of different sizes are available, including: 7.9mm (tent flap), 8.5, 9.5, 11.2, 12.7mm, and 12.7mm.

How long do tent shock cords last?

The shock cord should survive at least a few years if it is properly stored. One word of warning, based on a friend’s experience: storing his tent and other stuff in an attic that would heat up more than the rest of the home significantly affected the life of elastic cable, PU materials, and glues used in shoes.

Should I put a tarp under my tent?

Placing some form of ground cover or tarp beneath your tent is vital for ensuring the longevity of your tent as well as keeping it warm and dry throughout the winter. Even dew will run down the tent walls and pool beneath your tent if the tarp is stretched too far out from the tent. A tarp should not be placed underneath the tent when camping at the beach, but rather inside the tent.

How can I make my tent more stable?

Start with the body of the tent and stake it down, starting with the windward side of the tent. Instead of driving your stakes straight down, angle them at 45 degrees to make them more stable and secure. Place boulders on the ground around the tent to help keep it in place as you stake it down. Increase the number of rocks you use to hold the stakes down.

How do you cut fiberglass without splinters?

Place masking tape along the cut line of a panel, mark the line on the tape using a pencil, then saw through the tape to reduce chipping and splintering. Inside corners cut in a panel should be rounded to prevent a fracture in the completed item as a result of a sharp corner.

Can I cut fiberglass stick?

Align the rear edge of the fine-toothed hacksaw blade with the pencil mark using a straightedge and a level. Allowing the hacksaw to slowly move toward you and then away from you will allow you to cut through the fiberglass stick.

Cutting should be continued until the fiberglass stick is divided into two halves. To finish the cutting operation, remove the masking tape off the fiberglass stick and discard it.

Is tent pole one word?

A tent pole is a pole that is used to support a tent. An entertainment production on a huge scale that generates significant money for the studio, television network, or investors in the United States (figuratively, film, television, theater).

How do you remove a ferrule from a tent pole?

Place the pole in a vice and heat the ferrule’s tip with a heat gun, grabbing the ferrule with pliers as it heats up, and turning it to check if it starts to move. It is important not to overheat the pole, since this will cause it to burn.

Can you buy the top half of a fishing pole?

In most cases, getting a new rod will be more cost effective than repairing an old one, unless you have a heritage rod or need to have the rod butt fixed. There are a plethora of various types of “2 part fishing rods” available. It is preferable to get a new rod that is suitable for your planned application. I hope this has been of assistance.

What’s a tentpole moment?

Share, share, share. Almost every company has a tentpole marketing moment – a time of year when the company’s reputation is at its highest point.

What does tent pole mean?

As used in broadcast and motion picture programming and films, the term “tent-pole” refers to a program or film that is important to the financial success of a film studio or a television network. It is intended to be an analogue for the way a strong center pole offers a secure framework to a tent construction.

How do you measure the diameter of a tent pole?

A vernier calliper can be used to determine the diameter required, or a tape measure can be used if one does not have access to one. Take a part of your pole and place it end down on a tape measure or a ruler on a table. Then take another section of your pole and repeat the process with the tape measure. Now, have a look at the diameter.

What is a tent ferrule?

When two composite rods or tubes are joined together, ferrules are utilized to link them together. They also make it possible to employ shorter carbon or fiberglass rods or tubes, as well as to construct and dismantle your finished product, resulting in a smaller container for transportation purposes.

What do you do with a broken tent?

Continue to: Repurposing Is the Most Effective Option. Recycle your tent by purchasing it from an online retailer. At a yard sale or garage sale, you may recycle your tent. Make Use Of A Local Recycling Center To Dispose Of Your Tent. Thrift stores are excellent places to recycle your tent. Don’t throw your tent in the trash or recycle it. Make Use of Your Old Tent for Indoor Recreation.

What’s another word for tent?

Ceiling, cover and roof are all terms that refer to a tentawning or a canopy.

Do tent poles need the elastic?

To create tension, the elastic must be less than the total length of all the poles once they have been strung. However, it is always a good idea to have a spare elastic band and a spare pole or two on hand in case you need to do a repair on the spot if possible.

Can I cut a fiberglass tent pole?

What is the best method for cutting fiberglass tent poles? Without a doubt, a basic hacksaw. If you don’t already have one, you’ll soon realize that you’ll need one. Masking tape a few loops around the area you want to cut, then do it outside. It will take around 3 minutes total.

How do I replace the shock cord in my pole?

Please click here to get a PDF version of these instructions. a fresh length of shock cable 70 percent the length of your pole is cut from the existing length To prevent the line from fraying within your pole, we recommend heating the ends of the cord to seal them and prevent fraying. Place the pole in the desired position and pull one of the pole’s end-stops out until the knot in the shock cord is revealed. If necessary, you can use pliers to remove the end-stop out of the way. To release the end-stop, untie or cut the knot on the end-stop.

  1. Remove the end-stop by untying or cutting it.
  2. Check to see that the end-stop is completely seated.
  3. Thread as many portions as feasible onto the shock wire while still leaving a few inches of shock cord exposed at the end.
  4. 5: Tighten the shock cord and secure it with a peg or similar item tied to the shock cord with an easy-to-release knot to prevent it from slipping back into the sections.
  5. Continue to thread the remaining portions onto the shock cord, making sure to seat them as you go.

Remove enough shock cord to allow you to knot the end-stop on with your fingers. Gently reinstall the end-stop in the pole and remove the peg from the pole.

How do I pitch a Hilleberg tunnel tent?

  • Begin by installing the poles, making certain that all of the parts are properly seated together. To set up the tent, start at one of the sides and put a pole into the pole sleeve just above the pole tensioner, sliding it all the way to the other end
  • Then, with the pole end that is closest to you inserted into the pole tensioner cup, pull the webbing until the edge of the tent reaches the holder, and repeat the process. Repeat the procedure described above with the remaining pole parts. To set up a tent like the Keron, which has two similar entrances, either end can be staked down first
  • To set up a tent like the Keron, grip the front corners and draw the tent out taut, then peg them down. When putting the tent up for the first time, it is best to relax the adjustable peg attachments so that they are at their greatest potential length. It is usually recommended that you man out your tent so that you may attain more tension later on. This is especially vital if there is going to be wind or if the weather is going to be terrible
  • Nonetheless,

As the inner and outer of your tent are meant to be pitched together, you won’t need to take them apart unless you choose to pitch one of them independently. For more detailed instructions specific to your tent, please refer to the pitching instructions page, where you can watch videos of each tent being pitched and download a PDF of the instruction book that came with your tent, among other things.

How do I pitch the inner tent separately?

  • To begin, detach the toggles on the inner tent and pull it out of the way. Prepare the inside tent by laying it out. Attach the pole holders (which may be ordered separately) to the toggles on the sides. Using the elastic shock cords as guides, you can now slide a pole across the canvas and into the pole holders on either side of the tent. On a tunnel tent, repeat the operation with the opposite pole(s). Using the inner tent as a guide, tie a guy line to each pole at the top of each side of the inner tent and peg them out to help you build it. The Akto, Allak, Soulo, Staika, and Tarra tents require separate pole holder kits that include additional webbing to attach the pole holders to the tents
  • The Akto, Allak, Soulo, Staika, and Tarra tents do not require separate pole holder kits. Please refer to the tent descriptions to see how many pole holders are required for your particular tent type.

More thorough instructions pertaining to your tent may be found in the instruction book that came with it, which you can find here. These throwing training books are available for download as PDFs from the pitching instructional website.

My tunnel tent is noisy, in strong winds, what can I do?

More particular instructions for your tent can be found in the instruction book that was sent with it. These throwing training books are available for download as PDFs on the pitching instructional website.

How tight should the door band be on my tent?

The door band’s function is to maintain the door of your tent at the proper size so that the zippers may operate properly. It is made of nylon. A tight enough door band is required to ensure that there is no stress across the zippers in order for this to be accomplished. The door band, on the other hand, should not be overtightened to the point where the door hangs freely when the door is closed.

How tight should the ground straps be on my tunnel tent?

When using our tunnel tents, the ground straps assist in maintaining the right height and tension of the poles. When they are properly fitted, there should be no stress on the connections that join the inner and outer tents caused by the poles themselves. Because of the excessive tension created by the ground strap, the poles will be put under unneeded stress, and the inner tent will droop inwards at the sides.

My tent has seen a lot of heavy use, how can I re-treat the fabrics?

In addition to being extremely robust, our textiles are also waterproof and highly water-repellent. Sun, wind, rain, and wear, on the other hand, will deteriorate any cloth with time. More information on how ultraviolet light may degrade textiles can be found here. Re-treating the fabric will increase both the protection against UV damage and the water repellency of the fabric, but it will have no effect on the tear strength of the cloth. Restoring the condition of your outer tent The Nikwax TentGear SolarProof, which is simple to apply and does not contain fluorocarbons, is the product we suggest for re-treating our outer tent materials.

TentGear SolarProof should be sprayed or brushed over the cloth, and any surplus liquid should be wiped away.

Please keep in mind that TentGear SolarProof should not be used on a new tent, but rather on a tent that has lost its water resistant capacity over time.

See also:  How To Build A Tent Inside

Restoring the condition of your inner tent Nikwax TX may be used to restore the water repellency of your inner tent after it has been exposed to the elements for an extended length of time.

Spray the TX with the same method as with TentGear SolarProof. Directly after, wipe away any extra liquid and allow it to dry. We encourage you to visit if you would like additional information about these items as well as information on where you can purchase them.

My tent is dirty. How do I clean it?

Setting up your tent and then cleaning it with a sponge and lukewarm water after your journey is a wonderful idea once you return from your adventure. We strongly advise against the use of any cleaning chemicals. Using a tiny brush, thoroughly brush the zippers to ensure that no sand or grit is left in the teeth of the zippers is also essential. Sand in the zippers can wear out the sliders, preventing them from functioning correctly again after they have been cleaned. Check and double-check that your poles and pegs are clean and free of damage before using them.

If the tent is really unclean and dusty, we usually wash it in the washing machine.

No matter how you clean it, be certain that the tent is totally dry before putting it away for the season.

How do I use a line runner?

1. To loosen the Line Runner, use your fingers to draw the line away from the Line Runner’s body, as indicated in the illustration. Pulling the line into the Line Runner’s channel will secure it in place.

My pole broke, what do I do?

One extra pole piece as well as a repair sleeve are included in each pole bag for convenience. In the meanwhile, you may use the repair sleeve to temporarily fix your pole until you get an opportunity to replace the damaged pole segment. To get a PDF with step-by-step instructions on how to repair a tent pole, click here. Making use of a repair sleeve Twelve. Slide the sleeve over the damaged pole and center it over the damaged area, then tape the ends of the sleeve together to secure it in place.

  • Pull the end-stop of the pole out until the knot in the shock cord is visible.
  • 2.
  • Untie the knot and remove the end-stop off the cord to complete the process.
  • Pull the pole apart to reveal the shock cord that is hidden underneath the broken piece of the pole.
  • 4.
  • Keep track of the order so that you can replace them in the proper sequence.
  • 6.
  • Reattach the end-stop to the shock cord with a knot.

My zipper doesn’t work, how do I fix it?

When there is a problem with a zipper, the first clue that anything is wrong is that the zipper will not remain closed when you try to zip it closed. What generally causes this is dirt and grit in the zipper, which wears microscopic grooves on the inside of the zipper slider as a result of the zipper being used. You may make a temporary repair by pinching the edges of the zipper slider together until you have the opportunity to replace it. It is critical to clean your zippers on a regular basis in order to avoid this from happening.

  • In order to replace the zipper sliders, first open up the stitches at one end of the zipper and then remove the little metal clip that is attached to it.
  • Remove the old sliders by sliding them off.
  • Install the new sliders by sliding them on and making sure that they are facing in the same orientations as the previous ones.
  • Double-check that the sliders are aligned appropriately, not only in the front and rear but also in the top and bottom.
  • It might be difficult to put the slider on with the flat end first on some occasions.
  • 6) Once you’ve begun to slide the zipper slider along the zipper, continue to pull on either side of the zipper to complete it.

7, 8. Once the sliders are in place and functioning properly, rejoin the stitches you undid and sew a few stitches to seal the end and prevent the sliders from coming loose again. Reset the metal clip if at all feasible.

How do I attach a line runner?

12. Feed the guy line through the opening on the bottom of the Line Runner, which is triangular in shape. 3. Pull the line through the connection point until it snaps into place. In the same manner as shown, thread the second end of the guy line through the other hole on the top of the Line Runner. 5. Tie the end of the guy line in the manner indicated on the right side of the picture. We propose that you tie your knot using an overhand knot. This completes the installation and makes your Line Runner usable.

How do I attach the Footprint?

The best time to attach your Footprint to your tent is just before you want to go camping. Lay your tent out on the floor with the floor facing up if you’re indoors. The Footprint should be placed directly on top of the tent floor with the logo side facing the floor, and its logo should be aligned as follows:

  • If the Footprint extends into the vestibule, the logo or logos on the Footprint should be aligned with the centre of the main outer tent door or doors if the Footprint covers the vestibule. Keep in mind that the main door on the Kaitum GT and Nallo GT is the large entrance, rather than the small entrance near the front of the extended vestibule
  • If the Footprint does not cover the vestibule, the logo on the Footprint should align with the logo on the inner tent door
  • The Rogen is an exception to this rule due to its asymmetrical design. When the Rogen Footprint logo is displayed, it should be in alignment with the logo that appears on one end of the Rogen outer tent.

Look on the back of the Footprint’s hang tag for specifics about your particular tent model. Once the Footprint is properly oriented, attach the toggles that are located around the circumference of the Footprint to the rings that are located at the bottom border of the outer tent’s bottom edge. When the tent is fully assembled, the reflective side and logo should be facing upward. When you pack up your tent at the end of a trip, you may leave the Footprint still connected. Just make sure that the entire tent, as well as the Footprint, is totally dry before putting it back in its place.

Why do the footprints on the Anjan, Rogen, and Niak tents not cover the vestibule?

The optional Footprints do not cover the vestibules on the Anjan, Rogen, and Niak tents since the outer tents do not extend all the way to the ground on these three models. During heavy rains, water can seep into the vestibule through the space between the outer tent wall and the ground in the vestibule. If the Footprint covered the vestibule area, water may seep below the tent and cause it to collapse.

My tent is paler after a lot of time in the sun, what happened?

Because the outer tents of the Anjan, Rogen, and Niak tents do not extend all the way to the ground, the optional Footprints do not cover the vestibules of these tents. During heavy rains, water can seep into the vestibule through the gap between the outer tent wall and the ground in that section of the tent. Unless the Footprint is placed over the vestibule space, water may seep below the tent.

How do I roll my outer tent door?

The optional Footprints do not cover the vestibules of the Anjan, Rogen, and Niak tents since the outer tents do not extend all the way to the ground on these three models. During heavy rains, water can seep into the vestibule through the space between the outer tent wall and the ground. If the Footprint covered the vestibule area, water may seep below the tent and into the interior.

How to Fix your Pole Set

Ever returned to camp after a long day on the trail to discover your tent overturned and your pole set a complete mess of shock cord and poles? If so, you’re not alone. Hopefully, the response is negative. However, occasionally a storm or a stray wind gust might have a negative impact on your tiny home away from home.

Fortunately, our staff here at NEMO has prepared for the worst, and your tent comes with a pole splint that can be found within the pole bag. Here’s what you’ll need to accomplish in order to go through the rest of your journey: 1.

  1. Locate the pole splint and the broken pole segment in your pole set by following the arrows. The pole splint should be pushed up the poles until it is covering the fractured pole piece. Make use of duct tape or repair tape to keep the pole splint firmly attached to the pole set. You can use a pole set until you’re able to return home and do a more thorough repair. Watch this video for a brief instruction on how to use it.

At-Home Repair

Once you have returned home, please contact our customer service department. Because pole segments are removable, you won’t have to replace the entire pole set if one segment breaks. If you have any questions, please contact us at 800-997-9301, or fill out our Spare Parts Obtain Form to request a pole section. In either case, they’ll be pleased to assist you in restoring your pole set to full functionality in preparation for your next expedition. Although disassembling a pole set might seem scary if you’ve never done it before, it should be a simple and quick operation as long as you follow the steps in the instructions carefully and thoroughly.

This chart may also be used to keep track of your progress once you have received the replacement pole section and are ready to begin the repair.

Once you’ve received the new pole segment, follow the step-by-step process below for replacing it in your pole set:

1. Remove the ball cap from the end of the pole that is closest to the damaged segment. After that, detach the ball cap from the shock cable with a screwdriver. Remove the ball cap from the pole by unscrewing it and pulling it away from the shock cord. 2: Untie the shock cord loop so that the shock cord may be readily threaded through the poles. One of the most common NEMO tent components, this three-pronged hub links the shock cable to the hub through a little black clip that can be taken out of the middle of the hub.

  • 3.
  • You may put a number on a piece of paper (or directly on the pole itself in marker) and name the poles as they come off the shock cord with that number as they come off the cable.
  • 4.
  • 5.
  • 6.
  • 7.

Special Instructions: Hubs

For damaged pole segments that need the removal of the shock cord from a central hub, this is the most effective procedure for restoring the hub to working condition. One of the most common NEMO tent components, this three-pronged hub links the shock cable to the hub through a little black clip that can be taken out of the middle of the hub.

Three-pronged hub: The Dagger, Aurora, Hornet, Hornet Elite, Firefly, and Dragonfly are all equipped with this hub, as are the Hornet and Aurora. One portion, the ridge pole of the tent, is joined to the other half by a little black clip, which is used to tie the shock cord to the hub of the tent.

The easiest way to remove this black clip is to:

1. To reach the shock cord of your pole set, use a sharp blade to go under the lip of the black hub covering and through the opening. It should easily pop out of the hub; we recommend removing both sides at the same time. With care, insert a blade between a lip on the hub covering and raise to release the cover. 2. Carefully pull the shock cable away from the black clip, allowing it to completely detach from the hub. This will assist in loosening the clip just enough to allow it to be removed.

  • In order to remove this clip, we recommend pushing it out via one side of the center hub aperture with a pen; do not hesitate to apply pressure because the clip is quite tough.
  • After that, you should be able to work it out far enough to be able to grip the other end with your fingers.
  • After you’ve finished repairing your pole set, thread a loop of shock wire through the hub leg until it pokes out of the centre of the hub.
  • 6.
  • 7.
  • To make a loop, feed the shock cable through the hub, then attach the black clip to the shock cord and pull the clip back into position in the hub to complete the loop.

Loose Shock cord? No problem!

Over time, shock cord’s elasticity might deteriorate as a result of its use. In the event that you observe fraying, loss of elasticity, or that the poles do not fit together correctly, it is critical that you replace the shock cord in your pole set. Shock cord may be found at most sporting goods stores and on the internet. You can also get in touch with us personally if you require shock cords. Following the installation of your new shock cable, you’ll want to disassemble your pole set according to the instructions provided above.

Do you have a question?

Leave a Comment

Your email address will not be published. Required fields are marked *