How To Put Away A Tent

How to Pack a Tent

Getting a tent back into its bag is not difficult once you are familiar with the process. The procedures shown below demonstrate how to efficiently pack a tent and all of its components. The imagery depicts what we do not want to see. There is an additional layer of space taken up by a separate fly from the remainder of the tent, and everything else is placed inside the bag. According to a friend of mine, this is how it was brought to me.

Step 1: Packing Up the Fly

As shown in the second figure, straighten up the fly and then fold it lengthwise so that the exterior (the parts with guy ropes) is inside of the fold as shown in the first picture. With a little skill and the help of two persons, it is quite simple to sweep the fly off the built tent (after removing/unfastening all of the supports) and fold it lengthwise.

Step 2: Folding the Fly

Make sure each end touches the nearest support before continuing to fold in toward the center. – One you’ve reached the middle, fold it over once more to seal it. If this stage is completed correctly, the fly should be the same width as any of the folded poles, as seen in the final figure. If this step is completed incorrectly,

Step 3: Rolling Up the Fly

Start by rolling the fly tightly from the top (the thinnest section and the part that is in the middle of the roof), and then tie it in a tight knot at the bottom. The tighter the fly is rolled, the easier it will be to stuff it into the bag at the conclusion of the session.

Step 4: The Main Tent

The large tent has been set up in such a way that it appears to have been built. On the right-hand side of the photo, closest to the bins, is the front entrance. Make certain that all zips, including those on the windows, are closed.

Step 5: Adjusting the Roof

Pull the canopy so that it lays level and is not too bunched up, using the center roof mounts, which can be either clips or tubes for the support rods, to do this. As indicated in the second photo, make sure the front door is flat and that any extra hangs over the back door. If you have a dome tent that does not have a vestibule, work in a circular motion, pulling each side tight before ending with the front of the tent. It is really beneficial to have the tent still tied down at this point.

Step 6: Folding the Vestibule

If your tent includes a vestibule at the front or back, fold it over so that it sits flat against the main body of the tent. Check to see that the front one is on top.

Step 7: Folding the Tent

To fold the tent in half, fold each side into the center of the tent and then fold the tent over so that it is a quarter of its original width.

Step 8: Putting It All Together

Everything should be set up at the front of the tent, starting with the fly and working your way back. Poles, pegs, and any other accessories should be placed towards the back of the tent. Roll the fly in completely first, then add the poles and roll it again (a half turn works here to keep it in place) Roll it again once you’ve added the pegs.

Add whatever extra you like and roll it all the way up to the end, tying it off. It is critical to roll the tent securely because if there is too much air in the tent after it has been wrapped, it will not fit inside the bag.

Step 9: Put It in the Bag and Do It Up

That’s all there is to it.

Be the First to Share

To properly pack away your tent, whether you’re about to leave on a vacation or returning from one, you must first learn how to set up your tent correctly. Expeditions, festivals, the Duke of Edinburgh’s Award, or simply a camping trip, tents come in a variety of forms and sizes, and each has its unique knack for putting them away. As a result, you must take care while packing your tentaway, or you may find yourself regretting your decision on your next vacation. Winfields Outdoors has put together this guide on putting away a tent to assist you.

Ensure that your tent survives the test of time no matter where you go by paying attention to each of these factors.

Why is it so important to pack your tent away properly?

Simply said, if you don’t properly store your tent, when you go to retrieve it for next year, it may be damaged or have other difficulties that are too late to be repaired before the next season begins. It is possible that whatever issues that your tent has when it is put away will still be present, and that it may even have developed new ones throughout the process of packing it away. More information may be found at: When it comes to camping, it is critical to thoroughly inspect your tent. So, what is the proper method of putting it away?

Dry your tent before it’s packed away

In the United Kingdom, if you’ve gone camping, there’s a good possibility you’ve seen a little amount of rain throughout your camping trip. If you were very unlucky, you may have even had to pack up your tent in the rain, which is never a pleasant experience. It’s also not very good for your tent’s structure. There is a considerable probability that your tent will be coated with mould or mildew when you next take it out of its bag if it is left damp in its bag after a rainstorm. This may necessitate a complete cleaning of the tent, which may cause your camping trip to be postponed or cancelled altogether.

Ensure that the entire tent is dry, including locations such as the pegging points and guy lines, before using it.

Check for rips, tearsbreaks

Modern tents are quite durable and can sustain a significant amount of wear and tear without breaking down. However, they are not invincible, and the occasional rip or tear may occur from time to time. As a result, it’s critical that you take care of them before you put your tent away. Furthermore, the last thing you want is to arrive at your campground, attempt to pitch your tent, and then discover that you have a damaged pole or a hole in your groundsheet. More information may be found at: The Definitive Guide to Tent Maintenance Maintenance When you get home, thoroughly inspect the whole tent, including the poles, for signs of wear or damage.

If the damage is small, you may be able to repair it yourself; however, if the damage is more serious, it may be necessary to replace a portion of the tent or the entire tent. At Winfields, you may get replacement tentpoles and guy lines, as well as repair kits that include items such as tape.

Fold or roll your tent properly

Most contemporary tents are quite durable, and they can resist a significant amount of abuse. It should be noted, however, that they are not indestructible, and the odd rip may occur sometimes. As a result, it’s critical that you take care of these issues before you pack up your tent. Not only might the rips develop worse with time, but the last thing you want is to arrive at your campground, attempt to pitch your tent, and then discover that you have a damaged pole or a hole in your groundsheet.

If the damage is minimal, you may be able to repair it yourself; however, if the damage is more serious, it may be necessary to replace a portion of the tent or the entire tent altogether.

Bag pegs and poles

Your tent pegs and poles should each come with a little bag in which to store them, and this bag is there for a reason: it keeps them organized. Make sure to put all of your pegs and poles (as well as anything else that could be a little pointy) in their proper bags, otherwise they may cause harm to your tent when it’s time to pack it up. You don’t want to penetrate the tent after thoroughly inspecting it or after purchasing it brand new. If you can’t find the bags, use whatever you have on hand to wrap them up and protect your tent from the sharp edges of the sharp spikes.

How to care for a tent – Tent Tips

  • Make sure to open up your tent and let it air out for a couple of hours before putting it down. You’ll need to sweep and clean the interior of your tent to remove any debris, dust, and filth that has collected within. Keep the tent doors slightly open while folding it up to allow for some air to flow through
  • Don’t completely close the tent doors when folding it up. Campers’ best friend is duct tape, so make sure you have some on hand for mending holes or tiny tears, as well as for securing poles until you can acquire a replacement. Footprints: a groundsheet that may be removed to protect the underside of your tent from damp ground or debris
  • In the event of a leaky seam, just cover it with sealant and allow it to soak into the material
  • Seam sealant When storing the tent, avoid laying it on its side since this might cause damage to the poles. Instead, lie it level.

More information may be found at: Best Way to Waterproof a Tent. If you can’t find the bags, use whatever you have on hand to wrap them up and keep them safe while you search for them. Take a look at our whole array of tent accessories or our entiretents collection, which includes: Large Tents|Family Tents|Polycotton Tents|Tents by Brand|Tents by Size To get you ready for 2020, check out more articles on theWinfields Blog. Don’t forget to check out our camping blog for more articles like this.

How to Fold a Tent Like a Boss: Dome / Cabin (13 Tent Care Tips)

Putting the tent together is actually rather simple. Particularly popular are dome tents. Furthermore, getting them down is not too difficult. Putting them back in the bag, on the other hand, is a another matter. In this post, you’ll learn how to fold a tent like a pro – and how to put it back in its bag, just as you did when you first got it!

How to Fold a Tent Like a Boss

You’ve been out in the woods for some days now. You have become one with nature. You can’t recall the last time you cleaned your hair, and you get the distinct impression that you might want to stay here indefinitely. But then you remember the hair washing and how lovely it would be to take a hot shower instead. In addition, you have work the next day. Your food supplies have been reduced to a can of baked beans and an onion, among other things. It’s past time to leave. The tent remains in place as you pack up camp, fill up the garbage bags, and load the car.

Because it is the most inconvenient item to take apart.

No need to be concerned any longer, since I’m here to tell you that it doesn’t have to be this difficult. No matter what size, shape, or style of tent you have, you will be able to pack it. The following are the four sections of this post:

  1. Tent Folding 101 (skip to the part you’re interested in)
  2. The proper way to fold a dome tent (go to the next step)
  3. Instructions on how to fold a cabin tent (go to the next section)
  4. 13 recommendations for taking care of your tent (skip to section)

Is it a rainy day? How to put up your tent in the rain is demonstrated here.

How to Fold a Tent: 5 Steps

Tent folding is governed by a few fundamental rules that are generally applicable. These are the regulations that must be followed:

  1. Before packing the tent, clean it well and check that it is completely dry. The tent will become moldy if it is left damp for an extended period of time. If you must pack anything damp, make sure to unpack it as soon as you get at your destination and dry it out immediately. To make the tent fit into the bag, it must be folded down somewhat smaller than the bag. Tent poles should be rolled within the tent. Make use of a knot to keep the tent tightly coiled
  2. Remove bumps and wrinkles to reduce the amount of superfluous mass

How to Fold a Dome Tent: 11 Steps

A terrific no-fuss way to folding a dome tent is demonstrated by this Australian gentleman. He makes the valid point that if you have three distinct objects to put into a bag, it will be far more difficult to get them all to fit than if you put them all together. The procedure is outlined in detail below the video. You may see it on YouTube.

  1. Make sure the tent is clean: Empty the tent of all dirt, food, and other possessions to ensure that the tent is clean and clear of obstructions
  2. Remove any tent pegs that may have fallen to the ground: Ascertain that all of your tent pegs have been gathered and placed in their respective bags, and then place them in the pole bag. Remove the fly poles from the ground: Remove any poles from the flysheet and fold them up into the pole bag before continuing. Inside the tent, lay the flysheet out as follows: Check to see that the flysheet is dry and clean before laying it down as flat as possible on the inner floor of the tent
  3. Open all of the tent doors at the same time: This will guarantee that any air trapped within the tent will be released rather than trapped inside the tent. Take down all of the tent poles: Remove all of the poles from the ground and place them folded back into the pole bag. Fold the main tent as follows: Make sure that all of the tent’s components are contained within the primary perimeter. By now, you should have a square that contains both the flysheet and the tent structure itself. In a squat position, lean the pole bag against the edge of the tent, about equal lengths from either end. This will serve as a point of reference for you when determining where to fold your tent. Take one edge and fold it in so that it is in line with the edge of the tent pole bag. Repeat with the other edge. Once you’ve completed one edge, repeat the process on the other so that you have a long rectangular form that is no broader than the pole bag. Remove all of the air and flatten down the resultant shape: Ensure that the tent is as flat and neatly folded as possible by going over it and eliminating any wrinkles or air pockets. Incorporate the pole bag into the tent as follows: Starting at one of the tent’s ends, place the pole bag and begin to wrap the canvas up around it as tightly as you possibly can. Please make sure that you are rolling it in a straight line so that one end doesn’t end up being thicker than the other. You can utilize your body weight to roll tightly and eliminate air as you go
  4. However, this is not recommended. To bring everything together, say the following: Tie two lengths of rope around each end of the cylinder once it has been properly rolled (you should have some from original packing). The Australian gentleman proposes making loops at one end of each length of rope, then looping the other end through and pulling to give the rope more stiffness. Put everything in one place! It’s finished, just like that! The tent should be able to fit inside the bag without any difficulty
See also:  How To Paint A Circus Tent Ceiling

How to Fold a Cabin Tent: 10 Steps

Make sure your tent is clean: Empty the tent of all dirt, food, and other things to ensure that the tent is clean and clear of obstructions. Dispose of any tent pegs that may have fallen to the ground. Inspect to see that all of your tent pegs have been gathered and placed in their respective bags, and then place them in the pole bag. The fly poles should be taken down. Any poles should be taken out of the flysheet and folded into the pole bag. Inside the tent, lay the flysheet out as follows.

  1. The tent doors should be opened from all directions: Any air trapped within the tent will be released as a result of this, and no air will be trapped outside.
  2. Remove all of the poles and place them back in the pole bag, folded up.
  3. By now, you should have a square that includes both the flysheet and the tent structure.
  4. Having a reference point for where to fold your tent will be really helpful.
  5. Repeat with the other edge and fold it in again.
  6. Remove all of the air and smooth down the resultant surface area: Examine the tent, eliminating any wrinkles or air pockets, and overall ensuring that it is as flat and neatly folded as possible.
  7. Make sure you’re rolling it in a straight line so that one end doesn’t get thicker or wider than the other end.
  8. In order to bring everything together, Tie two strands of rope around each end of the cylinder once it has been neatly rolled (you should have some from original packing).
  9. Make a mental note to put everything away.

If all goes according to plan, the tent should fit inside the bag without any difficulty.

  1. Remove the stakes from the ground: Remove all of the stakes from the ground surrounding the tent so that the tent is no longer held in place by the stakes Remove the poles from the ground: Remove all of the tent poles from the tent’s main frame. Lay the tent out flat as follows: Make sure the tent is laid out flat on the ground and that it is either a square or a rectangle form, depending on your preference. When using a flysheet, be sure to keep it flat and clean when placing it within the form. Fold the tent in half as follows: Once you’ve smoothed out the tent, fold it in half over itself and store it away. Take some time here to iron out any kinks, air pockets, or other issues that may have arisen, and double-check that the tent is nice and level
  2. Fold the tent in half a second time: The tent should be folded in half again so that it is a long rectangular shape now, and once again you should take the time to level it out and clean it. Contrast the length of the storage bag with the length of the folded tent. The fact that the storage bag is the same length, if not slightly longer, as the short edge of the folded tent is amazing. If the tent is larger in length, you will have to think about folding it again. To achieve this, you should aim to have an atent that is almost the same length as the storage sack when it is folded. Fold the long rectangle in thirds as follows: Fold one-third of the tent over on itself to make it more compact. Tent poles should be rolled into the tent: Using your body weight to keep the roll extremely tight and smoothing out air pockets and uneven areas as you go, start at one end of the folded tent and work your way toward the other end. To keep the wrapped tent in place, knot the ends together as follows: Tie them together so that the roll remains securely coiled
  3. Place it in the bag as follows: If everything has been done correctly, the tent should be able to be packed up safely in its bag.

Do you require a tent? See our Ultimate Buyers Guide to the Best Family Camping Tents for more information.

13 Tent Care Tips

A tent is required. Consult our comprehensive guide on the Best Family Camping Tents for further information.

  1. Always read the instructions before doing anything: Despite the fact that tents have many similarities, they are all somewhat different, therefore it is vital to become familiar with your specific tent and to have the instructions close at hand. Use caution when working with zippers and poles: Considering that they are the most delicate parts of your tent, they should be handled with caution at all times. Once they have been destroyed or lost, they are extremely difficult to repair or replace
  2. When dismantling poles, begin at the centre and work your way out: This ensures that tensions are distributed uniformly along the rope. Maintain the cleanliness of your tent and ensure that it is dry while not in use: Although it should go without saying, dirt and dampness may lead to mold, and mold is a negative thing. Mold is something you do not want. It has a foul odor and can be hazardous to your health
  3. It should be avoided. When you return from a trip, make sure to thoroughly air dry your tent: Even if the tent has not been wet, it is still a good idea to do this at the conclusion of every trip to ensure that the tent is completely dry
  4. Consider keeping your tent in a more flexible container at your residence: Although it is crucial to keep the tent in its bag for excursions, consider storing it in a bigger container at home, such as a pillow case, to enable air to circulate through the fabric while it is being kept to prevent mildew growth. Check to see that it is not being stored in a wet or moist environment. Never wash your tent in the washing machine: It is necessary to clean it, but this should be done with a sponge and some mild soap rather than in the washing machine. This will cause the material’s critical coatings to break down. Check the waterproofing and make any necessary repairs: Over time, the waterproofing of your garments may become weakened, particularly at the seams of your garments. You’ll need to figure out what kind of material your tent is composed of and then make the proper repairs. For polyurethane tents, a water-based seam sealer will be used, and for silicone tents, a silicone sealant will be used. If your tent has a little hole in it, you may also fix it with repair tape, just like you would a bike inner tube
  5. However, this is not recommended. Consider utilizing a footprint or tarp to protect your property: Even though tents are waterproof, if the weather is very rainy, a tarp beneath the tent will help to guarantee that your tent is not ruined by excessive water. It will also protect your tent from any stones or thorns that may penetrate your tent and cause it to become unusable as a result of the damage. As someone who has experienced this firsthand, I can assure you that it is not enjoyable, and you will not be aware of it until you are using your tent in really wet weather. Later, in the middle of the night, you will discover that all of your things, including your sleeping bag, have been saturated with water
  6. Stay away from leaving your tent set up in direct sunlight for an extended amount of time: UV radiation will degrade the fabric of your tent, causing it to deteriorate. Boots should be left outside the tent: It is possible for boots to contain foreign things that might puncture your tent, as well as dirt that can deteriorate it over time. Only wear socks or bare feet before entering your tent. Do not leave your dog unattended in the tent:I’m not sure what your dog is like, but mine likes to dig, roll, scratch, and do a variety of other things. you get the idea. Unsupervised, they may get up to anything, which could include causing damage to your camper’s canvas tent. It’s also a good idea to verify that their claws are cut short before you leave to reduce the likelihood of any punctures to your tent. Food and toiletries should be kept in a container with a tight fitting lid: Maintain a lockable receptacle on the outside of the tent or in the vestibule for any food or personal scent products you may bring. If you keep these kinds of objects in your tent, they may become too enticing for little (and large) animals, who may attempt to gnaw through your tent material in order to get to these items, leaving you with a hole in your tent (and an animal within it!)

Thank you to REI for providing some of the ideas for these suggestions. Additional reading: How to properly stake a tent

Your Turn

You should be able to go camping and amaze all of your friends with your tent folding abilities now that you have the information. There is nothing better than getting to the conclusion of a pleasant weekend knowing that you will not be forced to fight with your tent for an hour in order to get it back into its bag. Now you can walk out into the wilderness (and inside whatever tent you may have) with the confidence that you will be able to get it back into its small, tiny bag if need be.

How to Store a Tent

An average rating of 4.4 out of 5 stars has been given to the product in 149 reviews. Following a long journey, it might be tempting to simply dump your stuff down and forget about it for a bit. However, this is not the best option. However, taking the time to unpack and carefully store your belongings can assist to ensure that your equipment will provide you with years of dependable service. This is particularly true in the case of your tent: Mildew development and material disintegration can occur fast as a result of improper storage.

  1. Check to see that your tent is entirely dry. Keep it in a loose container in a cold, dry location.

Step 1: Dry Your Tent

To be on the safe side, make certain that your tent is completely dry before storing it. A tent that is stored in a moist environment may develop mildew, which will give your tent a musty stench after a while. Moisture has the ability to permanently destroy polyurethane waterproof coatings, rendering them unusable. A tent that has become flaky, sticky, or stinky is most likely because it was not allowed to fully dry before being put away in a storage facility. This may be avoided by putting up your tent indoors or in a sheltered outside location to dry it off before using it.

Maintain a clean environment: If you arrived home from your adventure with a dirty tent, taking the effort to clean it can help it last longer, especially if it has been exposed to sand, fine dust, bird droppings, and tree sap during its time on the trail.

Allow the sap to dry completely before gently spot cleaning with mineral oil or other alcohol-based products such as hand sanitizer or wet wipes to remove it.

An old toothbrush may be used to remove grit from zippers, allowing them to operate smoothly.

Step 2: Store Your Tent Loosely in a Cool, Dry Place

At the very least, be certain that your tent is completely dry before putting it away. The mildew that develops on a tent that has been stored in the rain can give your tent a musty stench. Additionally, the dampness has the ability to permanently degrade polyurethane waterproof coatings. A tent that has become flaky, sticky, or stinky is most likely because it was not allowed to fully dry before being put away in a storage space. This may be avoided by putting up your tent indoors or in a sheltered outside location to let it dry off.

Maintain a sanitary environment.

Spot cleaning filthy cloth with cold water and a moderate, non-detergent soap is simple.

After you’ve finished, make sure to thoroughly rinse with water. An old toothbrush may be used to remove grit from zippers, allowing them to flow smoothly. Find out more about how to clean your tent in this article.

Related Articles

  • Tent Care Fundamentals
  • How to Repair a Tent
  • How to Set Up a Tent
  • Tent Maintenance

Contributing Experts

Chris Pottinger works at REI Co-op in Kent, Washington, as a senior tent designer.

How To Roll Up A Tent . And Get it Back In The Bag

Getting a tent back into its bag, complete with tent poles, inner tents, and other accessories, may be difficult. Here’s a simple technique for putting your tent away and completing that nearly difficult process in one piece. So, to summarize.

  1. Fold the tent so that it is slightly thinner than the bag in which it is stored. It’s important to remember that your tent should be completely dry before storing it up. If not, you may need to take it outside to dry when you get home. Bring the tent poles to the table. These are often packaged in their own bag. Place the tent poles at one end of the tent and roll the tent up around the poles to close the tent up completely. This should be kept as tight as possible. The weight of the poles aids in the expulsion of the air. Leaving vents and doors open will aid in the removal of the trapped air. Depending on the form of your tent, begin by rolling the end that is furthest away from the entryway
  2. You should finish up with a tent that is beautifully rolled and small enough to go back into its bag. If you have a piece of ribbon or rope, wrap it around the tent to keep it from unwinding.

The tent is seen in its plastic bag, together with the tent poles and the inner tents, which are all contained within the main tent bag in the last photograph. Our rolled tent is normally kept in a separate bag from the inner tents so that we can get it out if it rains without getting the inside tents wet, but this illustration shows that it will all fit back into the tent’s original bag after it has been unrolled. This is a really basic tip that is quite effective. Try it out and see how it works for you.

See also:  The Useful Tips On How To Stay Warm In A Tent

Get the Family Camping Planner

You will receive the family camping planner once you have entered your name and email address.

How to Fold a Tent: A Complete Step-by-Step DIY Guide

Despite the fact that setting up a tent is as simple as ABC, folding it back into its bag may not be the same story. This is made considerably more difficult if you have never seen or misplaced the instructions for the tent before. Because of the tiny size of a tent, knowing how to fold one makes it much easier to transport it. Alternatively, see:Ultralight Hiking Equipment: For a Stress-Free, Lightweight Hike A tent that has not been folded correctly creates an ideal environment for mold growth.

To fold your tent, you will need the following items:

  • Washing rags for use in cleaning the tent
  • A sleeping bag for the night
  • The twine that will be used to bind the tent together

Steps to effectively folding a camping tent

Camping necessitates the transportation of a large number of items for usage in the wild. They are usually kept in the tent when not being used. As a result, the first step will be to remove everything from the tent and then, using a clean wet rag, clean the interior of the tent’s interior. Remove any food particles or anything else that might serve as a breeding ground for mould by cleaning the area thoroughly. After you are finished cleaning the inside of the tent, move on to the outside of the tent and repeat the process.

It is preferable to let it air dry.

Make assured that everything is completely dry before proceeding.

Remove the stakes or pins holding the shelter

Having cleaned and dried your tent, it’s time to remove the pins that hold it to the ground. Remove the pins from the tent’s corners. Place the pins or stakes in a separate bag or in your backpack so that they are easily accessible. Keep the stakes in a different location from where you are keeping the tent, but not in the same location as where you are storing the tent because this may result in damage to the tent’s fabric. This is due to the fact that the pins and stakes are sharp objects that might cause damage to your tent.

Remove the poles

This is so simple that even a 6-year-old can do it. All that is required is that you remove the poles out of the loops in your tent.

After that, fold the poles in the appropriate manner. Some tent poles are made up of several parts that may be joined together to form lengthy poles. If this is the situation with your poles, remove the segments that are affixed to the poles and store them in their pole bag.

Shake up the camping tent

Cleaning up the tent may not always imply that you are finished. As amusing and strange as it may sound, you must pick up your tent and shake it well before using it. The only reason for doing this is to clear away any debris that may have accumulated on the tent.

Make the tent flat

The next step is to put the tent on the ground once you have finished cleaning it. Pull the tent all the way down to the ground until it is completely flat. Check to see that the tent’s bottom is likewise dry before proceeding. If it is not completely dry, wipe away the excess moisture with a small piece of fabric and let it aside to dry for around 20 minutes.

Fold up the tent

You must be really focused at this phase in order to fold the tent properly and into extremely little pieces. To begin, elevate the outside pieces of the tent and bring them closer to the center of the tent. The folds should be positioned in a straight line from top to bottom. Important to remember is that you should fold the tent longitudinally rather than widthways. When folding the tent, be sure that the tent’s door is on top of the fold. Fold the tent so that it is just a fraction of its original width dimension when it is not in use.

In order to avoid this, you must pat the inside of your already folded tent to verify that no air is trapped within it.

Pack up the fly

Now that you’ve finished working on the main tent, you’ll need to straighten the fly and fold it lengthwise so that the outside portion of the fold is within the fold. This is something that two people should have no trouble putting together.

Folding the fly

Take care to carefully fold the ends of the fly, making sure they meet the nearest supports, and then continue folding it towards the center. When you have reached the middle, fold the flyover once more.

Put everything together

Place everything out in front of the tent, starting with the fly nearest to you and working your way out to the tent poles, pegs, and anything else that is farthest away. Before you do anything, you must completely roll in the fly, insert the tent poles, and roll it again. Put the pegs back in and roll it up once more. Incorporate any remaining ingredients and roll till the finish, tying it properly at the end. When rolling the tent, make sure to roll it firmly since allowing too much air inside the tent can cause issues when folding, as the tent may not fit into the bag.

Put the tent in the bag

Having carefully folded your tent and stowed away all of your belongings, there isn’t much more left to do except put your tent in a bag and wait for the next camping trip, whether it’s with your friends or by yourself. When it comes to folding a normal tent, the methods outlined above are the most basic. Tents, on the other hand, come in a variety of styles. The following are the procedures to folding some of the most common tents available on the market:

Folding a Cabin Tent

A cabin tent is fairly large and can accommodate groups of up to ten individuals.

While putting it together may not be difficult, getting it inside the tent bag is a different story entirely. If it is not folded correctly, it may not fit properly in the bag. Several factors should be taken into consideration when folding a cabin tent:

  • Remove moisture and dirt from the fabric by wiping it on both the inside and outside of the cloth. Take down the tent poles and pegs
  • The tent should be laid down level on the ground in the shape of a square or rectangle. In order to prevent lumps from forming, fold the tent in half and ensure that the tent is entirely flat. Fold the tent in half once more to create a rectangle that is longer than it is wide. Confirm that the tent bag is the correct length. If the width of your tent after it has been folded is more than the length of the bag, you will need to fold the tent again. Begin by folding the tent in half, starting from the narrow end, and putting it in the bag.

Folding a Backpacking Camping Tent

This tent is a favorite of individuals who want to travel light while camping. So that’s how you fold a backpacker camping tent, step by step.

  • The tent should be cleaned and dried thoroughly to guarantee there is no mold growth and that it does not have a foul smell
  • Whether it’s pins or stakes, Remove anything that has been used to secure the tent to the ground so that it may be moved. It is important to keep the pins and stakes in a different location from the tent bag in order to avoid ruining the fabric of the tent. Fold the tent poles after removing them from the loops. As long as the poles can be tied together or placed in a different bag all together, they should be OK
  • Otherwise, they should be stored separately. The tent should be shaken to get rid of any remaining dirt and to straighten the cloth. Place the tent on the ground so that the entryway is towards the top of the structure. Fold the bag in half starting from the sides and working your way towards the middle. Check to see that there is no air trapped in the folds or lumps of fabric. Roll inside the tent starting from the spot that is furthest away from the entrance. Finally, tie it securely and place it in the tent bag to finish it.

Folding a Dome Shaped Tent

In order to minimize mold growth and a bad odor in the tent, it should be cleaned and dried thoroughly before use. Be it pins or stakes, the results are always the same: To do this, remove whatever it was that had been holding the tent down to the ground. The pins and stakes should be stored separately, rather than in the tent bag, so that the tent fabric is not damaged; Fold the tent poles once they have been removed from the loops of the tent. As long as the poles can be tied together or placed in a separate bag all together, they should be OK; otherwise, they should be discarded.

Place the tent on the ground so that the door is towards the top of the structure.

When folding the bag, start folding it from the sides and work your way toward the middle of it.

Begin rolling into the tent from the place furthest away from the entryway.

  • Pack the flysheet in the trunk of the car. Before you do anything, make sure the flysheet is straight. Fold the fly in half lengthwise, with the outer section of the fly folded within the fly. Fold the fly in half lengthwise again, this time with the outside section facing inside. If you want to do it well, you can utilize a second hand. Fold the fly in half. Retuck the fly’s ends to the nearest pole, then collect the fly’s ends towards the center and fold it in once more. Repeat with the other fly. If everything is done correctly, the flysheet of each pole should be the same width. The fly is being rolled up. Begin by working your way up to the top of the fly, concentrating on the lightest section of it. Roll it up firmly and secure it with a knot. When folding the tent, the tighter the fly is, the simpler it is to fit it into the bag. The tent should be spread in the same manner as it was built. Make certain that all zippers are completed
  • Make the necessary adjustments to the roof part. The center roof mounts will serve as excellent support rods for the structure. Pulling the canopy can help to ensure that it is completely flat. Don’t be concerned about the surplus fabric. Simply place it over the area of the rear entrance and fold the vestibule down to the floor. Fold the vestibule so that it lies over the body of the tent, with the top portion of the vestibule resting on top. If your tent does not have a vestibule, you may skip this step and just fold the tent. Fold each edge of the tent towards the center, then fold it in half again to reduce the size of the tent to a quarter of its original size
  • Gather everything together. Place everything on the front section of the tent by first placing the fly sheet, poles, pegs, and any other items that you want to use in the tent. Adding one element at a time, rolling once, adding another and rolling again, and lastly rolling the end of the tent and tying it properly is the best way to go about this process. The tent should be rolled extremely tightly to eliminate unwanted wrinkles while folding and rolling, since any extra air will cause the tent to not fit in the bag.

Useful Tips When Folding a Tent

It is recommended to pay close attention to general instructions on how to fold your tent correctly. Here are a few pointers that are crucial.

  • Tents are available in a variety of sizes and from a variety of companies. It is also essential that you consult to your user’s handbook for instructions and information pertaining to your specific tent, in addition to the information provided on this page. Every tent features distinct fold lines that are visible at the time of purchasing. While folding your tent, make an effort to navigate your way through the creases and, if possible, discover the fold lines. Using this method will save you a lot of hassle and time. Clean your tent thoroughly and allow it to air dry to ensure a longer lifespan. Avoid lumps and creases that aren’t required in order to avoid gaining excessive weight. Make certain that no sharp things, such as pins, are stored with your tent in order to protect the fabric.

Importance of Knowing How to Pack Away a Tent

Those searching for something that can be put up quickly and will keep them comfortable during the night while they are out in the jungle will almost probably opt for something that will cost a significant amount of money. Tents are quite costly, and learning how to properly care for them will save you a significant amount of money in the long run. A tent that has not been properly tacked down is typically heavier and bulkier due to the fact that the weight has not been evenly distributed. Knowing how to pack away your tent will make it much easier to transport it whether you are trekking or going hiking.

Check out our study of the best ultralight tent for additional information on your alternatives.

Final thoughts

All campers must be able to pitch a tent, which is an essential skill. Spending the night in the woods with a bunch of friends is a great way to spend the evening. While the experience may not have been as warm and cozy as you would have liked, the memories made are ones that should be treasured. A large majority of campers are familiar with the feeling of having to pack up their tent. Typically, people collapse the tent and roll it inside the tent bag, however this never results in the tent bag fitting properly.

However, with the information provided here, you may forget about the blues and have a simple time folding your tent. Check out our simple instructions on how to create a DIY camping tent for inspiration if you want to save even more money. Source of the featured image:

Tent Packing: Stuff, Roll, Or Fold?

Purchases of $100 or more at the Outside Shop, where you’ll discover gear for all of your outdoor excursions, will earn you $50 off your purchase. Sign up for Outside+ as soon as possible. A perplexing decision must be made at the conclusion of every outdoor adventure: whether to stuff, roll, or fold your tent into its stuffsack. If you poll your fellow hikers, you’ll find that everyone has a preferred strategy and a compelling argument for why theirs is the best. If you challenge them, you may find yourself with a tent pole in your eye.

  1. However, much of our thinking is illogical (with the exception of one staff member who claims to split his decision into three categories: 70 percent stuff, 25 percent roll, and 5 percent fold—depending on the tent).
  2. went straight to the source, asking tent manufacturers from every major brand both what they recommend and what they do themselves in terms of design and construction.
  3. When it comes to their personal lives, though, even tent makers are prone to laziness and just slack off: Big Agnes (also known as “Big Agnes”): When I’m backpacking, I’ll cram the tent with all of my belongings.
  4. When I’m vehicle camping, I lightly fold my clothes before rolling them.
  5. Kelty/SD: It is more convenient to roll my own tent since it takes up less space in my bag (and looks a little nicer when set up) and because I am a tent man (and I want my tent to look beautiful!).
  6. My tents are typically rolled, but if they are damp or I am in a hurry, I will fill them instead.
  7. It’s more convenient, quicker, and – most crucially – better for the tent’s longevity.
  8. Once I’ve finished cleaning and putting the tent away, I roll.
  9. Are you a stuffer, a roller, a folder, or something else?
  10. T.
See also:  How Many Cfm Fan Do I Need For A 4X2X6 Grow Tent

Here’s How to Store Your (Hopefully Clean) Tent for the Winter

In spite of the fact that temperatures in Northern California are expected to reach the mid-60s next week, I am reluctantly putting up my summer toys, and by that I mean camping gear, for the winter. All year, my garage is like a gear rental business, with tents and sleeping bags strung over drying racks, backpacks hooked on door corners, and sleeping pads that have not yet been inflated arranged neatly on a table. When it’s warm out, I tend to use those toys, I mean tools, more frequently, so I don’t bother with neatly storing them away.

I don’t pay much attention to cleanliness when on the trail, and I’m sure I’ll get the thing dirty again quickly after returning from a trip, so I like to store my tents loose and open to allow for proper air circulation and ventilation.

Except for sun bleaching, my tent is 15 years old and still looks and functions as well as it did when it was first purchased.

With that in mind, we went out to NEMO’s Kendall Wallace for a Q/A on how to properly care for something as important as a tent so that it can care for you as effectively as it can.

When it comes to NEMO gear, Wallace is the one who deals with customer queries and warranty issues. He has experience with NEMO tents, so he is well aware of the best procedures for maintaining their functionality.

How to Store Your Tent

AJ: This summer, I’ve tented in a lot of places. My tent is in disarray. This place is filthy. For the winter, I want to make sure there aren’t any oils or patches of moisture that will cause the poles to jam while collapsing or opening. I also want to make sure there aren’t any oil or moisture patches that will cause the poles to jam. What is the best way to clean it? KW: On a microscopic level, dirt and grime can ruin the coatings on your tent that keep you dry and comfy while you’re camping.

  • Instead of using standard detergents, go for a tent-specific cleaning and re-waterproofer.
  • Tent poles require special attention to ensure that they survive as long as possible.
  • Cleaning the ferrules of the poles should be done with great care (the part of the pole that inserts into the next segment).
  • When bent into position, these places have a greater likelihood of cracking or breaking as a result of the increased force placed on the connection.
  • These may easily become clogged with dirt, sand, and other debris, which can cause problems with the way the door opens and closes.
  • Have you ever noticed your zipper “re-opening” behind your zipper slider after being closed?
  • Depending on the extent of the damage, a temporary remedy may be possible, or a new zipper slider may be required.

Don’t let mold or mildew form on your tent while it’s “drying” in a clump in your garage; else, all of your hard work will be for naught.

Is there any reason why a tent should not be stored in its stuff sack when it is rolled up?

Changing up the rolling pattern or packing the tent straight into the stuff sack can assist to reduce the likelihood of coatings breaking down during transport.

This will aid in the evaporation of any remaining moisture and the preservation of the materials.

While preparing my tent for storage, I found a tear in the wall of the structure.

Take care of it right now!

Depending on the extent of the rip, it may be something that can be repaired with a purpose-built patch (we recommend tenacious tape) or it may be something that requires the assistance of a professional repair center.

Almost anything may be mended, including broken zippers, tears in the floor, holes in the netting, broken poles, and other minor issues.

Many tapes include adhesives that are nearly tough to remove from tent fabric, making a simple repair that would otherwise be straightforward impossible to execute.

If the tent is dirty, but I’m too lazy to clean it, is there any damage in storing it in its unclean state without washing it?

It is beneficial to clean your tent immediately after usage, just as it is to clear a pile of dirty dishes, in order to limit the amount of crusty spaghetti sauce that requires 5 minutes of scrubbing.

Take the time to thoroughly clean your equipment, and it will serve you well for many seasons to come!

Do you have any recommendations for re-waterproofing a rain fly?

You should inspect the tent floor if you see this happening on the rain fly since it can happen on any of the waterproof materials on the tent, including the groundsheet.

Cleaning should be done with a cleaning that has been designed particularly for your item, followed by another DWR treatment. Many of these treatments will not adhere correctly until they have been thoroughly cleaned, so don’t neglect this step.

How to Put Away a Pop-Up Tent?

Pop-up tents are a fantastic invention. They make camping a piece of cake. They are, on the other hand, quite difficult to transport. That’s why we’re providing you with step-by-step instructions to assist you in putting your tent back into its original storage bag. Make certain that your tent is completely dry. Using a clean, dry cloth will work if you can’t bear the thought of waiting for it to dry naturally. Alternatively, you may use a sponge dipped in water and mild soap to remove any mud or debris off the underside of your tent.

  1. With one hand, fold the top high arches of your tent into the centre, while keeping them in place with the other hand.
  2. All three points may be obtained with a single hand.
  3. Your tent should be in the shape of a taco.
  4. Once the tent is erect, lower the uppermost component of the tent.
  5. Twist the tent to make two circles, dragging one of the circles over the other to form a ring.
  6. Using the built-in snaps, Velcros, or ties, you can keep your tent secure.
  7. You’re finished!

How to Fold Up a Pop Up Tent

Documentation Download Documentation Download Documentation A surprising number of individuals utilize pop-up tents as quick and simple shelters, but discover that folding the tent is an unanticipated headache. Folding the tent poles together and then over each other is the best method for storing it. Using this method, you can collapse the tent into a circle that can be stored in a bag until you need it again. With a little understanding of tent folding procedures, you’ll be able to store your tent until you need it again.

  1. 1 Before you begin folding the tent, clean it well. In most cases, shaking out dirt, sand, and pine needles is all that’s required of you. Despite the fact that you can try again later, the debris may become lodged in the tent folds. Tip the tent to the side to allow the debris to drain. When you have the opportunity, thoroughly clean the tent using a little amount of powdered laundry detergent and a damp towel.
  • Never put away a wet tent, otherwise you’ll wind up with mold on your hands

2Fold the top two poles together to form a triangle. Place yourself next to the tent. The poles are the ridges on top of the tent to your left and right that go parallel to the ground. Extend your arms to grab both sides and bring them together at the same time. Third, fold the two poles at the bottom of the frame together. The tent’s outside boundaries are formed by the bottom poles, which now protrude to the left and right of the tent’s center pole. You’ll have to find a way to get to both of them.

  • Repeat the process with the other bottom pole to ensure that all four poles are held together.
  • The folded tent has the appearance of a large taco.
  • Adjust the position of the taco form so that the open side of the taco shape touches the ground.
  • You’ll have to stretch your hands out once more to complete the task.

Reach out over the highest portion of the tent while holding the four poles together. Grab the rear of the taco form with one hand and pull it down to the other with the other. Wrestle the tent down to the ground in order to level it.

  • You won’t require more than a minimal amount of force to draw the tent down because of the lightweight nature of the poles. The poles are also flexible, making it unlikely that they would break.

You won’t require more than a minimal amount of force to draw the tent down because of the lightweight poles. In addition, because the poles are flexible, they are less prone to break.

  1. 1 Before folding the tent, shake it to remove any particles. Before you put the tent away, make sure it’s completely clean. Turn it over and shake off any dirt or sand that has become trapped within. With a little water and a hose or a towel, you can clean the tent up well after that. If you don’t have time to deal with stubborn stains right away, you may put the tent away and complete the task at home.
  • When washing away difficult stains, a small amount of powdered detergent might be beneficial.

2 Grab the tent’s sides with both hands. Position yourself in front of the tent’s entrance. The tent pole that runs from side to side above the entrance is the one that is closest to you. Grab hold of both edges of the tent with both hands. If the door has a cover on it, you should leave it open.

  • Beach tents are often smaller in size than conventional tents, and they do not have poles running across the width of the tent as do regular tents. In addition, if you’re still having difficulties folding any other tent, you may try this method.

3Fold the tent’s sides together to form a square. The tent should be pulled in one direction toward the center, then pushed flat on the ground. While you’re holding it down, move the other side across and place it on top. It should now be in the shape of an oval. Fourfold the tent and flatten it flat against the ground. Turn the tent so that it is resting on its side. Push down on the middle of this edge with your fingers. As you flatten the tent, it will take on the shape of a figure-8. To assist in guiding the tent to the ground, you might place one hand on either side of the tent.

Keep your hands on the tent!

The tent should be picked up from one side and then carried over to the other side.

While you’re doing this, you may rest one leg on the tent to ensure that you don’t lose your hold.

  • Because the poles are extremely flexible, there is no need to be concerned about them breaking.

6Disassemble the tent and put it away. Alternatively, if the tent came with an elastic band, you may use it to keep it in place. Place the tent in its carrying bag. Any poles that are protruding out should be tucked in, and the bag should be closed until you are ready to use the tent again. Advertisement Create a new question

  • Question What happens if the top of my tent collapses? If you need to replace it for safety concerns, you can use duct tape, glue, or other materials to temporarily repair it
  • However, this is not recommended. Question Do pop-up tents have compartments on the inside? No. In addition, there are various types of tents that do contain them
  • For example,

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

  • Every tent is a little bit different in how it folds. For more folding information, go to the instructions that came with the tent
  • If you don’t have the instructions that came with the tent, look online for folding videos. Because all pop-up tents employ the same fundamental folds, you should be able to fold up any tent with a little practice and experimenting.

Thank you for submitting a suggestion for consideration! Advertisement

About This Article

To fold a small pop-up tent, begin by facing the entrance of the tent and grabbing both of the poles on either side of the door. Article SummaryX Once this is done, bring one side of the tent down to the ground and push the other side of the tent down on top of it, forming an oval shape with the tent. Flip the tent so that it is standing on the edge and press down on the center to form a figure-8 shape with the sides. Last but not least, fold the tent over itself to form a circle and slip it into its storage bag.

Did you find this overview to be helpful?

Did this article help you?

Leave a Comment

Your email address will not be published. Required fields are marked *