How To Make A Hunting Tent

DJ Stand: Build a Customized, Portable, Elevated Deer Hunting Blind for About $500

Perhaps this scenario is similar to you: you’ve located a fantastic deer hunting location, but you’re having trouble figuring out how to get there. Perhaps there isn’t a suitable tree from which to attach a stand. Alternatively, a ground blind may not provide a sufficiently clear vision of the surrounding region. Alternatively, you could like to be protected from the wind, rain, and snow. The only thing I regret about that final one is that I wasn’t tough enough to confess it. All of these signs are pointing towards the same direction, which is: You’ll need a deer blind that’s high above the ground.

You might purchase a pre-made lifted blind, but be prepared to spend several hundred dollars.

Do you enjoy constructing shit?

We set out to build a wicked deer stand for less than $500, which is why we’re all assembled here today to discuss our plans.

Do you understand what I’m saying?

  • It is possible to construct in a weekend using ordinary tools. No power equipment are required to construct this stand, however a chop saw and drill driver will come in handy to finish it in time for football season. It is constructed of materials that can be purchased at Home Depot for less than $500. Prices for Pandemic were too expensive, but we came close with our design and now have a version that costs less than five dollars. However, we utilized ordinary timber, so if you happen to have some on hand, it might save you some money
  • It’s also portable. More or less, to be honest. Like other hunters, we have a general understanding of where the deer in our area congregate. There’s a high probability that, like all hunters, we’re entirely off the mark. We created the DJ Stand so that it could be readily transported in the bed of a full-size pickup truck. We specifically built it to fit in an F-150 pickup because it’s the most common truck in America, and we’re aiming for the whole “common tools” motif here
  • It’s also protected from the outside elements. Pre-dawn hunts in our region are frequently conducted in temperatures that are below freezing, and in some cases, below zero. The wind is no joke in this part of the world. Long sitting are much more tolerable with our stand
  • Make itBadass. This monstrosity appears like it was sprung from the 2001 monolith, and it can accommodate two large, highly armed individuals. How much more badass do you want to add to your collection

The second important feature of our design is that it is completely adjustable. In order to have a better opportunity of viewing the deer hidden in the long grasses of the marshes that meander through our estates, our DJ Stand is elevated 7 feet above the ground. (We live next door to each other.) However, it would be simple to construct it such that it sits on the ground. Our version is designed for two people, but you could easily reduce the horizontal measures to make it suitable for a single person.

Here’s how we went about it: First and foremost, a message from the attorneys: Derek and Joe are not engineers in the traditional sense.

Though its creators have tested it and determined that it is safe, you should proceed with caution.

You are solely responsible for the construction and use of this stand.

The Floor

If the DJ booth were a living creature, the floor would serve as its spinal column. Because it is the structural foundation of the entire project, we constructed it as if we were constructing a house. In fact, it’s identical to a residential subfloor in every way. In the event that you plan to use this as a ground blind, you might want to consider using pressure-treated 2x4s, which will hold up better when exposed to moist ground. Given that we intended to have our DJ Stand suspended in the air (and that we were on a tight budget), we went with simple stud lumber.

Because of the expansion and contraction our frame will suffer while sitting outside in the weather, we used ordinary nails to join the two pieces together.

We then topped it with 1/2 inch pressure-treated plywood to withstand the weight of our wet boots. The construction of this structure is almost likely excessive, but if you’re going to be in the air, overbuilding is the way to go. Cuts:

The floor frame is 60 x 48 inches. Derek Porter’s full name is Derek Porter.

The Walls

A 15-degree angle is carved into the walls’ tops to accommodate the pitch of the roof, which allows them to rise up from the ground level. In the front (longer) posts, the tops of the angled cuts should be 78.5″ from the top of the angled cut to the top edge of the floor’s perimeter 2×4 joist (78″ to the floor); in the rear (shorter) posts, the tops of the angled cuts should be 66.5″ from the top of the angled cut to the joist (78″ to the floor). We did a little experimenting with the way the posts attach to the floor, and the way they connect to the floor has an affect on how long you’ll be able to use them for.

  1. With the post sitting directly on the perimeter joists, its tenon can be extended through the plywood and nestled in the corner of the box that will eventually become your floor.
  2. The carriage bolt that secures the legs through the frame also travels through this tenon, resulting in a more complete integration of the structural components.
  3. Here’s an example of what this attachment looks like: On the left is a 4×4 wall post that is fastened to the floor.
  4. Derek Porter’s full name is Derek Porter.
  5. The legs of the stand are secured to the floor and wall via a carriage bolt.
  6. The second alternative is to just place your post directly on top of the plywood floor and leave it there.
  7. In order to strengthen the structure, we installed additional 2×4 under the floor, up against the perimeter joists as follows: Floor with additional 2x4s against the perimeter joist (on the left).

Derek Porter’s full name is Derek Porter.

We used nails to hold the assemblies together and screws to attach them to the posts in order to achieve a tight fit while yet allowing for mobility.

In the front, we have one stud that is smack dab in the midst of things.

That’s the bare minimum of breadth we believed we could provide a hunter who was wrapped up.

It’s not like we’re attempting to install a flat-screen television in this space.

You can use our measurements, but we recommend that you first place your four corner posts and then measure the distance between them.

While it will move no matter what you do, tight fitting will assist to minimize this movement. The following were the dimensions of our three walls: 53″w x 78″h on the front wall; 53″w x 65″h on the back wall; and two 41″w side walls with sloping tops on the sides. Cuts:FRONT

  • The bottom and top studs are 2x4s at 53″ in length
  • Vertical studs are 2x4s at 75″ in length, with the tops cut at 15-degree angles across the larger dimension of the 2×4. Make certain that the highest point of the angled cut is 75″ high.
  • The bottom and top studs are 2x4s at 53″ in length
  • Vertical studs are 2x4s at 75″ in length, with the tops cut at 15-degree angles across the larger dimension of the 2×4 (bottom and top studs). Aim for a 75-inch maximum height at the highest point of the angled cut.
  • 2x4s at 41″ (bottom stud)
  • 2x4s at 75″ (front stud)
  • Tops of 2x4s cut at 15-degree angles across the shorter dimension of the 2×4 To ensure a 75-inch high point on the angled cut, use a 2×4 @ 63″ (rear stud) top with 15-degree angles cut throughout the length of the 2×4’s longer dimension. 2 x 4 @ 42.7′′ (roof support studs)
  • 63″ at the highest point of the angled cut
  • 63″ at the lowest point of the slanted cut

A view of the framed walls from the front. Derek Porter’s full name is Derek Porter. We installed horizontal window sills 36 inches from the ground to give structural stability as well as a safe location to put a rifle while in the house. The sills were attached to the studs by screwing some 2×4 scraps into the studs and then screwing the sills into the scraps. In order to better shed water, we experimented with angling the sills down; however, this proved to be a major pain in the rear when it came time to attach the cladding.

We didn’t install any sills at the back of the vehicle.

The size of the spaces between your studs would be determined by the length of the sill.

  • 2x4s at 24.25″ (front sills)
  • 2x4s at 38″ (side sills)
  • 2x4s at 24.25″ (back sills)

Window sills that are integrated into the wall frames. Derek Porter’s full name is Derek Porter.

The Roof

We went with a fairly straightforward, single-pitch roof. It will shed water, and because it only has an overhang on one side, it will prevent water from running into our entrance. This also means that you may lay it on three of its four sides without crushing anything underneath. It is not structural in any manner because there is little debris in our area to be concerned about. Using 6’6″ posts and top wall studs, we cut the taller side at a 15 degree angle, resulting in a shorter side that is around 5’6″ tall.

The roof was sided in the same manner that the walls were sided.

You might consider adding a center brace if this is an issue for you.

The Skin, Windows, and Door

During our discussions over the cladding, we went back and forth a lot. Derek choose corrugated metal roofing because it is very lightweight, inexpensive, and provides a significant amount of stiffness to the entire structure. Joe, who has a fidgety nature, was concerned that being enclosed in a metal cage would cause him to sound like a pinball bouncing around in a snare drum and frighten every buck in North America. We made a pact with ourselves and used corrugated asphalt roofing material as a compromise.

  • In reality, it might be beneficial in masking a great deal of background noise.
  • The material’s peaks and valleys would allow everything smaller than a rabbit to pass through them.
  • It’s quite inexpensive and lightweight, plus it sheds water.
  • While it is not seaworthy, it does a good job of keeping the rain at bay.
  • That saved us a ton of weight and engineering time on the project.
  • We recommend this technique because it is more accurate: As soon as the frame was finished, we positioned our sheets against it and indicated the beginning and end of each anticipated cut.
  • Corrugated plastic is quite simple to deal with; all you need is a straight edge of any type and a utility knife to get started.

Derek Porter’s full name is Derek Porter.

The corrugated plastic covering that covers the rear wall and doorframe is an excellent choice.

Duct tape was used to seal the seams, which is a must-have for any excellent field engineering project.

We attached a single piece of string to the middle of the bottom edge of each window flap and threaded it through a small hole in the top of the wall that we had punched earlier.

A little stick was fastened to the thread to prevent the string from bending the flap when we tugged it open with our fingers.

To keep the windows closed while we aren’t using them, we attached threads to the two bottom corners of each strap and then connected them to the popped-up screws as well as the straps themselves.

Bottom: Strings are used to keep the windows open and shut.

It appears to be rather smooth, doesn’t it?

The lack of handholds provided by the plastic covering is a major drawback.

When we’re moving the object around, we can grab it.

Reason being: A wood-on-wood contact will be more stable in the field and will perform better in terms of weatherproofing and water resistance.

Water and snow are diverted away from vulnerable places, such as the end grain of the legs, by cutting flaps in the fabric. The purpose of this flap over the end grain on the legs is to divert water away from the legs. Derek Porter’s full name is Derek Porter.

The Legs

We purchased ten-foot pressure-treated 4x4s and did not even bother to cut them at all. There’s no way we’re going to be standing on a dance floor.) We elevated ourselves seven feet above the ground by running the legs three feet up the sides of the stand. We secured each leg using 12-inch-long carriage bolts; two bolts per side run through the floor and into the corner 4×4 posts of the stand walls, anchoring the legs to the stand walls. One each side continues through the floor’s circumference, linking into the strongest rectangle in the stand.

See also:  What Fan For Grow Tent

Derek Porter’s full name is Derek Porter.

Transporting It

Our platform is intended to fit in the shortest accessible bed of a recent Ford F-150 pickup truck, with the tailgate down, because almost everyone either has one or knows someone who can loan them one of these vehicles. It’s definitely not safe to drive on the highway with the legs connected, but you could bounce about your own property (which we did, and it was OK) or cruise down a gravel road with the legs attached. Just make sure you secure it with plenty of straps. The stand was created to fit into the bed of a Ford F-150 pickup truck (just make sure to strap it down carefully).

Taking the legs off is considerably safer than leaving them on.

It doesn’t matter how you choose to move it; the stand was created to be constructed from the bed of a truck, for example.

Eventually, the Stand will take over the driving, and one person will be required to leap out and prevent the stand from traveling all of the way over to where the action is.

Securing It

Manipulating your stand into position should be done with caution after it’s up. We utilized 15-inch ground anchors and attached them to the carriage bolts, which extended through the floor frame at the time of installation. Alternatively, you might attach the stand to a tree or something similar. I implore you not to simply put this stuff up and call it a day. As long as there are no two men up there in a 30 mph wind, it’s quite stable. Make use of the man lines. Before jumping onto the DJ stand, make sure it’s properly secured with four ratchet straps.

Misc Details

An eye hook on the underside of the stand secures our door, which is held closed by a bungee cord that runs through it. On the inside, we have a tie to keep it closed, much like we have on the outside windows. Isn’t it possible that you observed that we didn’t put up a ladder?

When you presumably already have a ladder lying around the home that you can contribute to the stand for a couple of months, why bother building one? Remember to leave it there for a few days so that the deer become accustomed to seeing it.

Shopping List

Every component of this project was purchased at Home Depot. We are not endorsing such companies, but we wanted to create something that practically everyone could afford. If we weren’t doing this for the benefit of the general public, we’d be supporting our local hardware store. A special shout-out to Herrington’s! To be more specific, here’s a list of items that you may get from Big Orange and make into a DJ stand: SHEATHING a ten-pack of corrugated plastic sheets in black (you’ll have enough left over) $210.60 Please keep in mind that Home Depot does not sell black sheets in singles, but they do sell white sheets in singles.

  1. Eh?
  2. ), you’ll be able to save $75 off the final bill.
  3. $136.44 divided by $22.74 equals $136.44.
  4. HARDWARE carriage bolts with a 1/2′′ x 10′′ zinc-plated head Bag zinc-plated 1/2′′ flat washers, 10 pack for $26.00, singles for $2.89 each for a total of $31.78.
  5. Duct tape in black, 37.98 cents per roll (60 yds) $8.42Total: $552.76 (or $478.60 if you choose the less expensive choices).

11 Free DIY Deer Stand Plans

For those of you who are or know someone who is a deer hunter, you might consider utilizing one of the free deer stand plans provided below to take your deer hunting to the next level. Included in these free building plans are free-standing deer stand designs, deer stand designs in trees, and box deer blind designs. They are available in a range of sizes and with a variety of features, so you should be able to pick the deer stand that is most appropriate for your hunting grounds. These free deer stand designs include diagrams, step-by-step building instructions, pictures, material lists, cut lists, and other useful materials in addition to the actual building plans.

Deer Blind

  • My Outdoor Arrangements This 6×6 deer stand has windows on all sides and can accommodate numerous persons at the same time. A list of supplies and equipment is provided, and each item that is required to construct the deer stand is indicated on an overview graphic in order to provide a very clear visual representation of how everything fits together. In addition to providing an overview, the design includes step-by-step directions and photographs that demonstrate how to construct a deer stand. My outdoor plans include a deer blind.

Two-Level Deer Stand

  • Free Deer Stand Plans are available online. This blueprint instructs you on how to construct a deer stand that extends 15 feet along the atree and includes both a platform at the top and a platform that is just 6 feet off the ground. You’ll discover a step-by-step guide that includes a list of supplies, cutting instructions, information on putting the top and bottom levels together, and information on completing the top. The tour is divided into five sections. According to where you obtain your supplies, you may anticipate to spend around $150 on this deer stand. Deer Stand with 2 levels for free from Free Deer Stand Plans are available on the internet.

Deer Tree Stand

  • Hydrogen Electrolysis is a type of chemical reaction in which hydrogen is converted into a molecule of oxygen. Due to the fact that this plan is for constructing a deer stand around a tree, it also contains a hand-rail, platform, and ladder. According to the directions, a 16-foot ladder is required, and there are specifics on how to put all of the components together as well as all of the particular dimensions. This plan includes over a dozen actual photographs of DIY deer stands, which can be seen at the bottom of this page following the construction instructions and diagrams. The Deer Tree Stand is derived from Hydrogen Electrolysis.

Octagon Deer Blind

  • Download this PDF file to acquire a deer blind design that is elevated off the ground and has a ladder entry, but does not require the use of a tree as a support structure. As compared to some of the other plans on this list, this one does not have as much text description. Instead, there are a plethora of sketches and dimensions that you must concentrate on in order to comprehend how to construct the deer blind. Deer Blind in the Shape of an Octagon Please proceed to number 5 of 11 in the following section.

Ultimate Economy Deer Hunting Stand

  • Free Deer Stand Plans are available online. Despite the fact that there is little shelter from the wind and other weather conditions, this deer stand may be constructed for a fraction of the cost of most others. It is 8 feet tall and 42 inches wide, with a swivel seat at the very top of the structure. You may follow through with the plan specifics for a materials and cut list, as well as information on how to build the ladder, top, and seat, as well as information on putting everything together and setting up the stand. The original builder spent $50 on this deer hunting stand, therefore you should expect a comparable amount to be spent on yours. Affordably priced deer hunting stand designed by Free Deer Stand Plans

DIY Deer Shooting Blind

  • My Outdoor Arrangements This deer box stand plan includes a plethora of illustrations and instructions to assist you in building it. It creates a fantastic raised deer blind that can be placed virtually anywhere you choose. A large number of user photographs and comments will also be available to assist you in customizing your deer stand to incorporate a blind and other features. My Outdoor Plans includes a DIY Deer Shooting Blind that I built.

Tower Box Deer Hunting Stand

  • Free Deer Stand Plans are available online. This is another free deer stand plan from FreeDeerStandPlans.com, but instead of being completely open to the elements, this stand is divided into two levels, each of which has a top and one that is completely closed in on the inside. FreeDeerStandPlans.com, like the majority of the deer stand designs on our list, includes all of the supplies you’ll need as well as written instructions to help you understand how it’s constructed. Deer hunting stand with a tower box from Free Deer Stand Plans

Scheierl Deer Stand

  • The Scheierl deer stand consists of a ladder and floor/platform that are placed beside a tree, and it is one of the most straightforward deer stands to construct. All of the directions for building this deer stand are contained in a single picture that can be saved and printed. It contains a complete list of the supplies you’ll need, 14 instructions to guide you through the construction process, and measurements for all of the cuts that will be made. It also offers some customized versions of it that may be better suited for what you’re looking for than the original version. A deer stand in Scheierl, Germany. 9th of 11th paragraphs are below
  • Continue reading.

How to Build a Tree Stand from Musket Hunting

  • Musketeering is a sport that involves hunting with a musket. Using a free deer stand plan from Musket Hunting, you can build a basic but robust seat in the tree with a ladder attached so that you can quickly access to it. Materials list, construction instructions, and color photographs are provided to assist you in making this straightforward project. From Musket Hunting, here’s how to build a tree stand.

Small DIY Deer Blind

  • How To Become a Specialist Another free deer blind plan is available at How to Specialist, and it will allow you to construct a modest blind that can only accommodate one person. This free plan comes with a materials list, a tools list, schematics, building instructions, and finishing advice, among other things. How to Make a Small DIY Deer Blind from How to a Professional

DIY Box Blind for Deer Hunting

  • The Outdoor Texan is a person who enjoys being outside. This free 4×8 deer blind plan from The Outdoor Texan is available on a single page with multiple illustrations to follow along with. This deer blind is expected to take around 10 hours to construct and will cost approximately $300. DIY Deer Hunting Box Blind from The Outdoor Texan
  • DIY Deer Hunting Box Blind from The Outdoor Texan

5×5 Deer Blind Plans

This step-by-step woodworking project is about free 55 deer blind designs, which can be found online. I had multiple requests for free blueprints to build a 55 deer blind, so I decided to make them available. The structure for this deer box is constructed of 2×2 timber. Also, remember to check out PART 2 of the project so that you may learn how to build the roof and the door, in addition to the rest of my hunting-related projects. See my previous do-it-yourself endeavorsHERE. We advise you to make the most of your money by purchasing the best products you can afford.

Always take precise measurements before modifying the size of the components to the appropriate size. Prepare the components by drilling pilot holes in them before to inserting the wood screws to avoid the wood from splitting.

Made from this plan

Putting up a 5 x 5 deer blind

Materials

  • A) two pieces of 24 lumber – 60′′ long, five pieces – 57′′ longFLOOR FRAME
  • B) one piece of 3/4′′ plywood – 48′′x60′′ long, one piece – 12′′x60′′ longFLOOR
  • C) two pieces of 22 lumber – 60′′ long, four pieces – 81′′ long, two pieces – 50′′ long, two pieces – 29′′ long, two pieces – 37′′ longFRON
  • 2 1/2′′ screws, 3 1/2′′ screws, 1 5/8′′ screws
  • 4d nails, 16d nails
  • Wood filler, wood glue, stain/paint
  • Stand brackets

Tools

  • Miter saws and jigsaws
  • Safety gloves and safety eyewear
  • A chalk line, a tape measure, a spirit level, and a carpenter’s pencil are all useful tools. Drilling gear and drill bits are used in drilling.

Time

Putting together the floor framework The first phase in the project will be to construct the floor frame for the deer blind, which will take many days. 2/4 timber should be cut into joists that are the proper size, as illustrated in the diagram. Drill pilot holes through the rim joists and insert three and a half inch screws into the perpendicular joists to complete the installation. Putting the floor sheets in place Attach the 3/4-inch plywood sheets to the floor structure of the deer blind using screws and wood glue.

  • For a professional-looking outcome, make sure there are no gaps between the sheets.
  • If you want to save money while also constructing a lightweight construction, cut the plates and studs from 2×2 timber instead of 2×4.
  • Pilot holes should be drilled through the plates, and 2 1/2′′ screws should be inserted into the studs.
  • You have the ability to customize the size of the apertures to meet your requirements.
  • Frames for the side walls 2×2 lumber should also be used to construct the side walls of the deer stand.
  • Make sure the borders are flush with one another and that the corners are square.
  • Using a spirit level, align the edges flush with the walls and plumb the walls.
See also:  How To Dry Out A Tent

Furthermore, you must use 2 1/2′′ screws to securely fasten the neighboring walls together as well.

Plans for a 5 x 5 Deer Box Remember to read PART 2 of the project so that you can learn how to construct the lean-to roof and how to attach the outer walls to the deer hunting shelter.

You have the ability to customize the size and design of the shooting house to meet your own requirements.

Please send me the photos at HERE.

Obtain PDF Floor Plans Thank you for taking the time to read our project about free 55 deer blind designs.

I encourage you to look through the other of the projects on our site. By utilizing the social network widgets, please remember to LIKE and SHARE our projects with your friends. Sign up to be among the first to learn about our latest initiatives. Previous|Next

How to Build an Inexpensive Hunting Blind

When I was younger, my family and I used to go hunting in handmade blinds that weren’t very good. These old structures, which were often drafty and leaky, were built to last only a few seasons, but they ended up sitting out in the elements for much longer than they were intended to last. I can put this down to my grandfather’s desire to see that his handiwork lasted as long as possible before he had to construct more. One summer, he planned to construct a new set of blinds that would be larger and more durable than the previous set.

Only a few of the blinds are still in place today, and they are only sometimes used.

Besides being long-lasting and durable, these vehicles are also comfortable and spacious enough to accommodate a spouse or child in the back.

In certain situations, constructing a blind is an excellent solution.

Box Stand

Cost ranges between $100 and $300. This design is four feet long and six feet high, so it has plenty of space for you and a friend to sit comfortably. It has one entrance with two tiny shooting windows and one huge firing window on either side of it. It is preferable to utilize pressure-treated timber in order to extend the life of the construction. Here’s everything you’ll need to get started: a total of twelve 8 foot 2x4s, three 8 foot 1x2s, and five half-inch pieces of plywood, all cut to 4 feet by 8 feet (2) door hinges made of 4×8 corrugated tin sheets Build a base out of 2x4s that are 4 feet by 8 feet in size, and then attach the 1×2 support lumber to the base to keep the construction stable.

  1. Start by constructing the frame using 2x4s, making sure that the rear of the blind slopes downhill toward the front of the blind.
  2. Most individuals should be able to stand comfortably at six feet tall with it.
  3. The 1×2 horizontal supports, which will also serve as a shooting rail in the front and sides, should be screwed into the frame.
  4. Cut a wide rectangular hole in the front wall, two shooting windows in the side walls, and a door in the back wall to serve as shooting windows.
  5. A door handle and latch is a wonderful addition that allows for simple access while also keeping the door closed in severe winds.
  6. If you want a raised blind, mounting brackets from Southern Outdoor Technologies are a good choice since they provide a stable basis for a blind frame.
  7. This will provide for a more expansive field of vision.
  8. Screw the timber into the mounts and then attach it to the base of the blind with the screws that were provided.
  9. Use olive drab spray paint to achieve the greatest results, and you may use tan or black to spray lines that will help to break up the overall form.

The use of camouflage netting along the windows will aid in concealment, although it is not required. Preferably, you should deconstruct the blind in pieces and then reconstruct it in your hunting spot.

Hay Bales

The cost is $100. (tractor gas, two bales of hay) When hunting near a field where hay bales are manufactured, this choice will be quite beneficial to you. The deer are already accustomed to seeing them, and they will be completely unaware that you are around. A framed blind with a hay exterior isn’t necessary, nor is it need to be elaborate. Simply bring two bales closer together with the tractor and fill in the gaps with more hay or branches. You can stack square bales on top of one another to build a solid wall between the gaps if you have access to them.

Natural Blind

There is no charge. Create a blind in minutes by utilizing the natural greenery around you. Locate a fallen tree if possible, but any bush will suffice to break up your outline if none can be found. To build a wall around the tree’s base, collect adjacent sticks and arrange them vertically along the tree’s trunk. When you’re seated, you want it to be high enough to conceal the majority of your body from view. Push sticks into the ground on the exposed side of the building until you’ve created a small area large enough for you to sit comfortably or draw your bow comfortably.

While this blind will not stay for very long, you can continue to treat it as required until it is restored.

15 Best & Free DIY Deer Blind Plans To Build Your Own

You must maintain complete concentration when selecting and shooting your target deer. So, avoid becoming distracted and improve your deer hunting skills by using these 15 free DIY deer stand plans, which will guide you through the process of building the most cost-effective hunting stands and blinds. These blinds will elevate your hunting experience to the next level by preventing strong winds and heavy rains from causing significant disruption to your enjoyment of the hunt. These stands are an absolute must-have for the next hunting season, and they should be included on your hunting equipment list without hesitation.

There are free designs available for anything from raised to ground deer blinds, as well as for everything from self-standing to tree hunting blinds.

For example, you may construct a two-level or multiple-level stand that will allow you to enjoy safe hunting at your preferred heights levels.

TheseDIY deer blind planswill make a wonderful present for any passionate hunter, and they would be easy to construct on a budget as well. So, complete the simple constructions and erect beautiful deer blinds before heading out into the woods to enjoy the hunting season to the fullest.

1. How to Build a Deer Blind

Have you begun preparing for the next hunting season yet? Have you considered include a deer blind in your plans? If you haven’t already done so owing to the larger financial commitments required, then download these free box blind plans and make one for yourself on a budget. Begin with constructing the foundation frame, followed by the side frames, and ultimately the roof frame. Lastly, sheath the whole frame, leaving enough room for windows to be installed. To construct the raised base, heavy-duty timber posts and poles should be used.

More information may be found hereyoutube

2. 5×5 Deer Blind Plans

Using a ladder, construct this extra-elevated do it yourself tree stand that will take a lot of space. It is elevated to a greater height in order to keep you safe from predators and to force you to keep your eyes on your prey. The chevron roof, 55 square proportions, and painted attractiveness are the primary elements of this 55 deer blind. It is available in two sizes. The floor, side frames, elevated base, and roof of this deer blind will be constructed out of 2x4s, 2x2s, and plywood, among other materials.

howtospecialist

3. Deer Blind Plans

Are you a hunter who enjoys your sport? A deer blind, on the other hand, will almost certainly be on your wish list. Before you go deer hunting in the woods, you need construct this deer blind at your residence. There are free plans, pictures, and measurements available to make it easier for you to construct a model that will last longer and look more fashionable. Build this raised home out of timber and plywood, which will serve as a hideout as you hunt for dears. myoutdoorplans.

4. Free 2-Level Deer Stand

When you’re sitting in a deer blind in the woods, waiting for the right moment to pick your target, you’ll frequently desire to modify the height of your shot to achieve the perfect shot. As a result, we are providing you with free raised deer blind designs for a 2-level deer blind. It is actually necessary to construct a two-level stand, with the blind deer house being able to be placed on any level for convenient hunting. When there is a threat, you will be able to rapidly access the higher levels thanks to its two-tiered stand.

freedeerstand

5. Hunting Blind Plans

Prepare for the hunting season by constructing this hunting blind, which will allow you to conveniently conceal yourself while selecting the target for precision shot. Due to the fact that you are elevated, you will be protected from being pursued as well. This hunting blind must be constructed on a tree that is approximately 16 feet above the ground level.

Being higher up will make it easier for you to locate your target in the trees. Simply build a wooden platform on top of the trees and secure it with bracing to ensure it remains in place. To gain access to it, you’ll need a ladder. hho4free

6. Ultimate Economy Deer Hunting Stand

One of the greatest DIY deer hunting blinds available, and it is also quite cost effective to construct. 2×4 wood slats and galvanized metal tubing are used to construct it. A flat elevated platform on the tree should be constructed, and a ladder should be linked to it for easy access. Because you are at a reasonable height, you can readily pick your target without coming into direct contact with a deer’s eyes. This ultimate economic deer hunting stand will make your deer hunting experience more enjoyable.

7. DIY Deer Shooting Blind

Are you intending to spend some time in the woods this fall to take advantage of the hunting season? Then there’s the matter of constructing a deer shooting blind, which will make it simpler to take down fast-moving deer. One of the best 48 deer stands available, this stand has sides that are somewhat exposed from the top, allowing you to look out and observe the target. It comes with a shingled roof and is made of 2x6s, 2x4s, and 3/4″ plywood. It is easy to assemble. Build the base stand independently from the rest of the structure, using heavy-duty wood posts and bolts.

8. Scheierl Deer Stand

Using this Scheierl deer stand, you may conceal yourself well in order to kill the deer flawlessly. It is constructed with 4x4s, 2x4s, 1x6s, 2x8s, and plywood. Prepare to cover the ultimately completed design with a black outdoor fabric, which will give protection against precipitation. Use an existing ladder to gain access to it, or construct a temporary ladder out of the remaining wooden planks. This is something that every professional hunter should have. More information may be found here.

9. Box Blind for Deer Hunting

The 2x4s will be used to construct the frameworks for the deer hunting blind, from the floor to the side walls and the roof. Sheathing the floor, walls, and complete model with plywood and constructing a sturdy box-style deer blind will allow you to hit the target with ease. If you have a little carpentry knowledge, it will be a breeze to construct the ideal hunting device for your next hunting season. Finish it off with a corrugated metal roof with a curved edge. OutdoorTexan has further information here.

10. Build Elevated Deer Blind

Check out thesedeer stand plansto learn how to build another form of deer blind that is supported by 44 uprights and stands on a robust base. The corrugated metal roof has a 15-degree slope, which means that rainfall will not simply fall through to the ground. This amazing 6′ x 6′ deer blind design is made from 2x4s, 2x6s, 4x4s, 2x3s, and 3/4″ plywood and measures 6′ x 6′ when completed. The free blueprint will walk you through the process of building everything from flooring to rafters to sidewall frames.

See also:  In A 5 Foot Grow Tent, How Tall Can You Grow Marijuana

The raised deer blind is one of the most popular elevated deer blinds to make at home.

11. Wood Pallet Ground Deer Blind

Get the free blueprints to build a zero-cost wooden deer blind by visiting this page. The whole credit for this ground deer blind belongs to free pallets, which served as the primary building materials. This variant does not include an elevated foundation and is instead a basic wooden chamber or cabin, which allows you to conceal yourself for optimal hunting conditions.

Cut off a little section so that you can easily peep out to observe your target as well as any other risks. All you need are some 2x4s, 2x2s, and some free pallets to assemble this beautiful wooden deer blind. You may also put it on a stand to make it more visible. greatdaysout

12. Portable Hunting Blind

The fixed hunting blinds only allow you to remain in one location; what do you do if you want to move closer to your target or pick another acceptable hunting location? There’s no need to be concerned since this portable hunting blind has come to the rescue. Metal pipes and fittings will be used to construct this blind hunting structure. Furthermore, you will be able to get free directions on how to construct a deer blind out of an old ambulance from this site. Here are the specifics: streamlined construction

13. Build Elevated Deer Blinds On A Budget

Purchasing bespoke deer blinds may be a very expensive endeavor. However, with the free blueprints provided, you can be your own boss and construct an elevated deer blind in your own backyard. Simply use 2x6s, 4x4s, 4x6s, and 2x4s to construct this deer blind that will survive for a longer period of time. Increase the coziness of this hunting hideout by bringing in rugs and clothing from home. Just remember to allow enough distance between the deer blind and the surrounding area to observe what’s going on.

gameandfishmag

14. Homemade Deer Blind

This deer bound resembles a giant vertical ladder that has been constructed on a tree stem. It gives a sturdy platform from which to stand and shoot deer at the very top of the structure. Being at a higher elevation will allow you to more easily locate your deer target, and you’ll need 2x4s and 1x6s to construct this longer-lasting ladder-style deer blind for maximum durability. The use of a huge tree to construct a deer blind only eliminates the need to construct a separate foundation stand for the blind.

15. Free-Standing Deer Hunting Blind

Take a closer look at the intricate intricacies of this one-of-a-kind deer hunting blind that is guaranteed to wow. It is supported by two heavy-duty timber pillars, which are really robust wood logs that have been driven deeply into the earth. Build the floor, sidewalls, and roof with the 2x6s and plywood that you saved earlier in the process. Maintain some open area so that you may peep out and pick a terrific target. Don’t forget to reinforce the braces that support the floor of the deer blind with additional bracing.

Conclusion:

Before embarking on a hunt, it is usually a top priority to put on protective clothing. So, before you head out into the woods to enjoy some deer hunting, make use of these simple DIY deer blind blueprints. The deer is one of the fastest moving creatures on the planet, and they have incredible senses that allow them to remain aware of approaching hunters. It won’t take long for them to vanish if they manage to track you out after they’ve vanished. As a result, these deer blinds will provide an ideal hiding place from which to choose and kill the target.

Related DIY Ideas:

DIY camper trailer ideas that are definitely on a low budget that you may build yourself are presented in this article.

You may simply create your own personalized version of a DIY camper trailer using simple tools and materials.

How to build the perfect deer-hunting ground blind

For the majority of my adult life, I’ve been hunting from the ground. My father, like other hunters in Louisiana, taught me how to hunt from a ladder stand constructed of 2x4s and plywood when I was a child. From that perch, I learned how to observe squirrels, birds, and the rare deer without being observed. As time progressed, though, things began to shift, and it wasn’t until the late 1990s that I felt it was time to branch out and try something new: hunting from a blind on the ground. To my knowledge, I was the first member in my family to even entertain the thought of hunting at eye level with my prey, and my proposal was received with a great deal of hostility when it was initially floated.

  1. It is difficult to sway the minds of children, and I was set on the prospect of getting up up and personal with a deer.
  2. The first year was challenging, but I gained a great deal of knowledge.
  3. Additionally, chicken wire topped with leaves and pine straw was used as a roof.
  4. There were a few things that weren’t quite right: the midday light would cast my shadow on the rear wall, and deer could plainly detect any movement from behind.
  5. Every time I went hunting there, I had deer within 30 yards of me, and I was able to take down six of them from the little, basic house.
  6. My friends have now discovered how much they like it as well, and a couple of them have created some of the most beautiful ground blinds I’ve ever seen for less than the face value of a fresh $100 dollar.

Establish a reason

Hunting from the ground is tremendously pleasurable, but it is not without its difficulties. When you believe you’ve discovered the ideal hunting location, the first thing you should do is seek out a high vantage point from which to conduct your hunt. For this reason, hunters prefer to hunt from elevated platforms since they are more effective. There are no natural predators that deer can encounter that hide in trees, so why would they bother looking up? The difference between hanging a lock-on stand in a tree and setting up a ground blind is that a ground blind will stick out like a sore thumb to even the most casual observer.

  • Because hunting from the ground may be exceedingly tough, I only do it when there is no other option or when I am looking for a challenge.
  • Greg Hicks stands in front of his ground blind with a doe in his arms.
  • The canopy was just too low for a raised platform, so the only alternative I had was to build a platform that was as low as possible.
  • Finally, as the light began to rise over the woods, I noticed a head easing out of my left-side window, and I knew I was on the right track.
  • I was trembling with anticipation.
  • The deer was tearing out of the woods in a cloud of dust as I drew my bow and unleashed it.
  • My dissatisfied expression belied my ability to remain calm and nock another arrow.
  • When the deer lowered its head down this time, the NAP Spitfire flew right through it and out the other side with ease.

While everyone else was using a gun to hunt, I was able to complete the task with a stick and thread from the ground. It was a difficult, taxing, and anxious quest, but it was one I will never forget.

Setting up

From the ground, this is frequently the most difficult portion of the hunting process. Ideally, I want to set up months in advance and give the animals time to become accustomed to the blind, but this is not always possible due to scheduling conflicts. Make sure to set up your ground blind well in advance of your hunt so that the deer may become accustomed to it. When it is determined that a ground blind is required, the first step is to determine where it will be placed. First and foremost, I search for natural cover to aid in the integration of the stand into the environment.

  • I want the sun to be at my back at all times for shade, and I also want the sun to be in the deer’s eyes while they are staring at the blind for protection.
  • I put this to the test some years ago with a swarm of crows who were feasting on my maize at a distance of 20 yards from my house.
  • One beautiful morning, I came to full draw on a flock of more than 15 crows, and they didn’t bat an eye.
  • Wind is something that I am aware of, but not quite to the extent that one would expect.
  • Unless there is a chilly front passing through, you will seldom experience a north or west breeze.
  • Another thing to keep in mind is that you will never, ever be completely scent-free unless you’re within a bubble of some sort.
  • I am able to walk around without making a sound, and I can scratch locations on the ground to release the odor of the soil on a regular basis if necessary.
  • As I enter inside my stand, I like to pick up pine needles and leaves from nearby gum trees to decorate the space.

As soon as I’m finished with them, I don’t discard them on the ground; instead, I shove them into my pockets, boots, and even my headband. Later on in the search, when I’m confident that no one is nearby, I like to renew them.

Brushing-in

Brushing in a blind is the most important component of hunting from a ground blind, just as it is when duck hunting. The stand must mix nicely with the surroundings in order for the deer to get comfortable and not startle. Ree Anderson’s first deer was taken from a ground blind only seven yards away. Following my decision on where to position my blind, I take a step back and picture how I want to brush it in. Huge trees and saplings in the region inspire me to seek for large materials to integrate into the design.

  • Pine plantations are a great spot to locate shelter since the branches will be easy to cut and gather in large quantities.
  • Because they die very rapidly, they soon become more noticeable rather than being covered up.
  • When feasible, I want to tuck my stand into a clump of trees to make it look more natural.
  • The presence of trees all around helps to break up the circular pattern that most store-bought ground blinds exhibit.
  • The deer will be accustomed to the fact that the top is down and may just pass by without paying it or you any attention.

Thinking outside the box

As previously said, my first ground blind was made of burlap and chicken wire, and it was just great. When it comes to building a nice ground blind, you don’t have to go out and spend several hundred dollars; you can accomplish it on a tight budget if you put in the effort and time to do so. In 2013, Farmerville resident John Anderson went above and above in his design of a handmade ground blind, and the result was something that was not only functional but also cost-effective. The deer that John Anderson shot from The Stump was killed at a distance of 30 yards.

  • In 2013, he received word from an employee that a local electrical supply firm was about to discard several very big metal wire spools measuring 8 feet in length.
  • He intended to hunt from a stream bank, where the tree canopy is relatively low, because the terrain was flat.
  • In the beginning, Anderson said, he struggled to obtain waste material.
  • A piece of plywood and roofing felt that I had lying around, as well as some vinyl flooring that someone was about to throw away, served as the roof.
  • The Stump measures approximately 7 feet tall by 8 feet in circumference and provides ample space for four individuals.

“It’s nearly to the point where it’s becoming too huge,” Anderson said. The aim is to build one this year that will be 6 feet around and will be used for bowhunting. The overall cost of “The Stump,” including the screws, welding rods, and sweat equity, came to around $53 in total.

JOIN THE CLUB, get unlimited access for $2.99/month

With a subscription to Louisiana Sportsman Magazine and LouisianaSportsman.com, you can become the most knowledgeable Sportsman in your circle of friends.

Leave a Comment

Your email address will not be published. Required fields are marked *