How To Fold Tent Back Into Bag

How to Pack a Tent

Getting a tent back into its bag is not difficult once you are familiar with the process. The procedures shown below demonstrate how to efficiently pack a tent and all of its components. The imagery depicts what we do not want to see. There is an additional layer of space taken up by a separate fly from the remainder of the tent, and everything else is placed inside the bag. According to a friend of mine, this is how it was brought to me.

Step 1: Packing Up the Fly

As shown in the second figure, straighten up the fly and then fold it lengthwise so that the exterior (the parts with guy ropes) is inside of the fold as shown in the first picture. With a little skill and the help of two persons, it is quite simple to sweep the fly off the built tent (after removing/unfastening all of the supports) and fold it lengthwise.

Step 2: Folding the Fly

As shown in the second figure, straighten up the fly and then fold it lengthwise such that the exterior (the portions with guy ropes) is inside of the fold as seen in the first picture. A little practice and two people make sweeping the fly off an erected tent (after removing/unfastening all supports) a breeze, and the result is a tent that has been folded lengthwise.

Step 3: Rolling Up the Fly

Start by rolling the fly tightly from the top (the thinnest part and the part that is in the center of the roof), and then tie it in a tight knot at the bottom. The tighter the fly is rolled, the easier it will be to stuff it into the bag at the conclusion of the session.

Step 4: The Main Tent

The large tent has been set up in such a way that it appears to have been built. On the right-hand side of the photo, closest to the bins, is the front entrance. Make certain that all zips, including those on the windows, are closed.

Step 5: Adjusting the Roof

Pull the canopy so that it lays level and is not too bunched up, using the center roof mounts, which can be either clips or tubes for the support rods, to do this. As indicated in the second photo, make sure the front door is flat and that any extra hangs over the back door. If you have a dome tent that does not have a vestibule, work in a circular motion, pulling each side tight before ending with the front of the tent. It is really beneficial to have the tent still tied down at this point.

Step 6: Folding the Vestibule

If your tent includes a vestibule at the front or back, fold it over so that it sits flat against the main body of the tent. Check to see that the front one is on top.

Step 7: Folding the Tent

The front and rear vestibules of your tent should be folded over so that they are flush with the main body of your tent. Make sure the front one is on top of the stack of papers.

Step 8: Putting It All Together

Lay everything out at the front of the tent, starting with the fly closest to you and moving outward. Next, add the poles, pegs, and any other parts that are farther away. First, completely roll in the fly.

Next, add the poles and roll again (a half turn works here to keep it in place). Finally, add anything else and roll up to the end and tie. It is critical to roll the tent securely because if there is too much air in the tent after it has been wrapped, it will not fit inside the bag.

Step 9: Put It in the Bag and Do It Up

That’s all there is to it.

Be the First to Share

That is all there is to say.

  1. Fold the tent so that it is slightly thinner than the bag in which it is stored. It’s important to remember that your tent should be completely dry before storing it up. If not, you may need to take it outside to dry when you get home. Bring the tent poles to the table. These are often packaged in their own bag. Place the tent poles at one end of the tent and roll the tent up around the poles to close the tent up completely. This should be kept as tight as possible. The weight of the poles aids in the expulsion of the air. Leaving vents and doors open will aid in the removal of the trapped air. Depending on the form of your tent, begin by rolling the end that is furthest away from the entryway
  2. You should finish up with a tent that is beautifully rolled and small enough to go back into its bag. If you have a piece of ribbon or rope, wrap it around the tent to keep it from unwinding.

The tent is seen in its plastic bag, together with the tent poles and the inner tents, which are all contained within the main tent bag in the last photograph. Our rolled tent is normally kept in a separate bag from the inner tents so that we can get it out if it rains without getting the inside tents wet, but this illustration shows that it will all fit back into the tent’s original bag after it has been unrolled. This is a really basic tip that is quite effective. Try it out and see how it works for you.

Get the Family Camping Planner

You will receive the family camping planner once you have entered your name and email address.

How to Fold a Tent Like a Boss: Dome / Cabin (13 Tent Care Tips)

Putting the tent together is actually rather simple. Particularly popular are dome tents. Furthermore, getting them down is not too difficult. Putting them back in the bag, on the other hand, is a another matter. In this post, you’ll learn how to fold a tent like a pro – and how to put it back in its bag, just as you did when you first got it!

How to Fold a Tent Like a Boss

You’ve been out in the woods for some days now. You have become one with nature. You can’t recall the last time you cleaned your hair, and you get the distinct impression that you might want to stay here indefinitely. But then you remember the hair washing and how lovely it would be to take a hot shower instead. In addition, you have work the next day. Your food supplies have been reduced to a can of baked beans and an onion, among other things. It’s past time to leave. The tent remains in place as you pack up camp, fill up the garbage bags, and load the car.

Because it is the most inconvenient item to take apart.

No need to be concerned any longer, since I’m here to tell you that it doesn’t have to be this difficult.

The following are the four sections of this post:

  1. Tent Folding 101 (skip to the part you’re interested in)
  2. The proper way to fold a dome tent (go to the next step)
  3. Instructions on how to fold a cabin tent (go to the next section)
  4. 13 recommendations for taking care of your tent (skip to section)

Is it a rainy day? How to put up your tent in the rain is demonstrated here.

How to Fold a Tent: 5 Steps

Tent folding is governed by a few fundamental rules that are generally applicable. These are the regulations that must be followed:

  1. Before packing the tent, clean it well and check that it is completely dry. The tent will become moldy if it is left damp for an extended period of time. If you must pack anything damp, make sure to unpack it as soon as you get at your destination and dry it out immediately. To make the tent fit into the bag, it must be folded down somewhat smaller than the bag. Tent poles should be rolled within the tent. Make use of a knot to keep the tent tightly coiled
  2. Remove bumps and wrinkles to reduce the amount of superfluous mass

How to Fold a Dome Tent: 11 Steps

Before packing the tent, make sure everything is completely dry and clean. The tent will become moldy if it is exposed to water for an extended period of time. As a precaution, if you must transport it damp, make certain that it is unpacked immediately upon arrival at your destination and thoroughly dried. The tent must be folded in such a way that it is slightly smaller in size than the bag The tent poles should be rolled into the tent. Using a tie, secure the tent’s roll-up shape. Reduce the presence of lumps and wrinkles in order to reduce the amount of extra bulk.

  1. Make sure the tent is clean: Empty the tent of all dirt, food, and other possessions to ensure that the tent is clean and clear of obstructions
  2. Remove any tent pegs that may have fallen to the ground: Ascertain that all of your tent pegs have been gathered and placed in their respective bags, and then place them in the pole bag. Remove the fly poles from the ground: Remove any poles from the flysheet and fold them up into the pole bag before continuing. Inside the tent, lay the flysheet out as follows: Check to see that the flysheet is dry and clean before laying it down as flat as possible on the inner floor of the tent
  3. Open all of the tent doors at the same time: This will guarantee that any air trapped within the tent will be released rather than trapped inside the tent. Take down all of the tent poles: Remove all of the poles from the ground and place them folded back into the pole bag. Fold the main tent as follows: Make sure that all of the tent’s components are contained within the primary perimeter. By now, you should have a square that contains both the flysheet and the tent structure itself. In a squat position, lean the pole bag against the edge of the tent, about equal lengths from either end. This will serve as a point of reference for you when determining where to fold your tent. Take one edge and fold it in so that it is in line with the edge of the tent pole bag. Repeat with the other edge. Once you’ve completed one edge, repeat the process on the other so that you have a long rectangular form that is no broader than the pole bag. Remove all of the air and flatten down the resultant shape: Ensure that the tent is as flat and neatly folded as possible by going over it and eliminating any wrinkles or air pockets. Incorporate the pole bag into the tent as follows: Starting at one of the tent’s ends, place the pole bag and begin to wrap the canvas up around it as tightly as you possibly can. Please make sure that you are rolling it in a straight line so that one end doesn’t end up being thicker than the other. You can utilize your body weight to roll tightly and eliminate air as you go
  4. However, this is not recommended. To bring everything together, say the following: Tie two lengths of rope around each end of the cylinder once it has been properly rolled (you should have some from original packing). The Australian gentleman proposes making loops at one end of each length of rope, then looping the other end through and pulling to give the rope more stiffness. Put everything in one place! It’s finished, just like that! The tent should be able to fit inside the bag without any difficulty

How to Fold a Cabin Tent: 10 Steps

Cabooses are usually extremely significant in size and construction. The majority of them feature a number of rooms and areas, and you can usually stand up straight in them.

Because the bags are often tight and there is more stuff to squeeze back in, putting them back into their bags is a particularly difficult task. Doing so effectively and without errors is essential. You may see it on YouTube.

  1. Remove the stakes from the ground: Remove all of the stakes from the ground surrounding the tent so that the tent is no longer held in place by the stakes Remove the poles from the ground: Remove all of the tent poles from the tent’s main frame. Lay the tent out flat as follows: Make sure the tent is laid out flat on the ground and that it is either a square or a rectangle form, depending on your preference. When using a flysheet, be sure to keep it flat and clean when placing it within the form. Fold the tent in half as follows: Once you’ve smoothed out the tent, fold it in half over itself and store it away. Take some time here to iron out any kinks, air pockets, or other issues that may have arisen, and double-check that the tent is nice and level
  2. Fold the tent in half a second time: The tent should be folded in half again so that it is a long rectangular shape now, and once again you should take the time to level it out and clean it. Contrast the length of the storage bag with the length of the folded tent. The fact that the storage bag is the same length, if not slightly longer, as the short edge of the folded tent is amazing. If the tent is larger in length, you will have to think about folding it again. To achieve this, you should aim to have an atent that is almost the same length as the storage sack when it is folded. Fold the long rectangle in thirds as follows: Fold one-third of the tent over on itself to make it more compact. Tent poles should be rolled into the tent: Using your body weight to keep the roll extremely tight and smoothing out air pockets and uneven areas as you go, start at one end of the folded tent and work your way toward the other end. To keep the wrapped tent in place, knot the ends together as follows: Tie them together so that the roll remains securely coiled
  3. Place it in the bag as follows: If everything has been done correctly, the tent should be able to be packed up safely in its bag.

Do you require a tent? See our Ultimate Buyers Guide to the Best Family Camping Tents for more information.

13 Tent Care Tips

Let’s go through some fundamental tent maintenance guidelines. These suggestions will ensure that your tent has the longest possible life and that you do not have to run out and buy a new one every other summer. The absolute fundamental rules are as follows:

  1. Always read the instructions before doing anything: Despite the fact that tents have many similarities, they are all somewhat different, therefore it is vital to become familiar with your specific tent and to have the instructions close at hand. Use caution when working with zippers and poles: Considering that they are the most delicate parts of your tent, they should be handled with caution at all times. Once they have been destroyed or lost, they are extremely difficult to repair or replace
  2. When dismantling poles, begin at the centre and work your way out: This ensures that tensions are distributed uniformly along the rope. Maintain the cleanliness of your tent and ensure that it is dry while not in use: Although it should go without saying, dirt and dampness may lead to mold, and mold is a negative thing. Mold is something you do not want. It has a foul odor and can be hazardous to your health
  3. It should be avoided. When you return from a trip, make sure to thoroughly air dry your tent: Even if the tent has not been wet, it is still a good idea to do this at the conclusion of every trip to ensure that the tent is completely dry
  4. Consider keeping your tent in a more flexible container at your residence: Although it is crucial to keep the tent in its bag for excursions, consider storing it in a bigger container at home, such as a pillow case, to enable air to circulate through the fabric while it is being kept to prevent mildew growth. Check to see that it is not being stored in a wet or moist environment. Never wash your tent in the washing machine: It is necessary to clean it, but this should be done with a sponge and some mild soap rather than in the washing machine. This will cause the material’s critical coatings to break down. Check the waterproofing and make any necessary repairs: Over time, the waterproofing of your garments may become weakened, particularly at the seams of your garments. You’ll need to figure out what kind of material your tent is composed of and then make the proper repairs. For polyurethane tents, a water-based seam sealer will be used, and for silicone tents, a silicone sealant will be used. If your tent has a little hole in it, you may also fix it with repair tape, just like you would a bike inner tube
  5. However, this is not recommended. Consider utilizing a footprint or tarp to protect your property: Even though tents are waterproof, if the weather is very rainy, a tarp beneath the tent will help to guarantee that your tent is not ruined by excessive water. It will also protect your tent from any stones or thorns that may penetrate your tent and cause it to become unusable as a result of the damage. As someone who has experienced this firsthand, I can assure you that it is not enjoyable, and you will not be aware of it until you are using your tent in really wet weather. Later, in the middle of the night, you will discover that all of your things, including your sleeping bag, have been saturated with water
  6. Stay away from leaving your tent set up in direct sunlight for an extended amount of time: UV radiation will degrade the fabric of your tent, causing it to deteriorate. Boots should be left outside the tent: It is possible for boots to contain foreign things that might puncture your tent, as well as dirt that can deteriorate it over time. Only wear socks or bare feet before entering your tent. Do not leave your dog unattended in the tent:I’m not sure what your dog is like, but mine likes to dig, roll, scratch, and do a variety of other things. you get the idea. Unsupervised, they may get up to anything, which could include causing damage to your camper’s canvas tent. It’s also a good idea to verify that their claws are cut short before you leave to reduce the likelihood of any punctures to your tent. Food and toiletries should be kept in a container with a tight fitting lid: Maintain a lockable receptacle on the outside of the tent or in the vestibule for any food or personal scent products you may bring. If you keep these kinds of objects in your tent, they may become too enticing for little (and large) animals, who may attempt to gnaw through your tent material in order to get to these items, leaving you with a hole in your tent (and an animal within it!)
See also:  What Size Mattress Fits In A 4 Person Tent

Thank you to REI for providing some of the ideas for these suggestions. Additional reading: How to properly stake a tent

Your Turn

You should be able to go camping and amaze all of your friends with your tent folding abilities now that you have the information. There is nothing better than getting to the conclusion of a pleasant weekend knowing that you will not be forced to fight with your tent for an hour in order to get it back into its bag. Now you can walk out into the wilderness (and inside whatever tent you may have) with the confidence that you will be able to get it back into its small, tiny bag if need be.

How to Fold a Tent: A Complete Step-by-Step DIY Guide

Despite the fact that setting up a tent is as simple as ABC, folding it back into its bag may not be the same story. This is made considerably more difficult if you have never seen or misplaced the instructions for the tent before. Because of the tiny size of a tent, knowing how to fold one makes it much easier to transport it. Alternatively, see:Ultralight Hiking Equipment: For a Stress-Free, Lightweight Hike A tent that has not been folded correctly creates an ideal environment for mold growth.

To fold your tent, you will need the following items:

  • Despite the fact that setting up a tent is as simple as ABC, folding it back into its bag neatly may not be the same story. The situation is made considerably more difficult if you have never seen or misplaced the tent’s instruction manuals before. Because of the tiny size of a tent, knowing how to fold it makes it much easier to transport. Alternatively, see:Ultralight Hiking Gear: For a Stress-Free and Lightweight Hike A tent that is not correctly folded creates an ideal environment for mold to flourish. It is also possible that improper folding could result in the formation of creases in the tent’s fabric, which would cause damage to the fabric. These items will be required to fold your tent:

Steps to effectively folding a camping tent

Camping necessitates the transportation of a large number of items for usage in the wild. They are usually kept in the tent when not being used. As a result, the first step will be to remove everything from the tent and then, using a clean wet rag, clean the interior of the tent’s interior. Remove any food particles or anything else that might serve as a breeding ground for mould by cleaning the area thoroughly. After you are finished cleaning the inside of the tent, move on to the outside of the tent and repeat the process.

It is preferable to let it air dry.

Make assured that everything is completely dry before proceeding.

Remove the stakes or pins holding the shelter

Having cleaned and dried your tent, it’s time to remove the pins that hold it to the ground. Remove the pins from the tent’s corners. Place the pins or stakes in a separate bag or in your backpack so that they are easily accessible. Keep the stakes in a different location from where you are keeping the tent, but not in the same location as where you are storing the tent because this may result in damage to the tent’s fabric. This is due to the fact that the pins and stakes are sharp objects that might cause damage to your tent.

Remove the poles

This is so simple that even a 6-year-old can do it. All that is required is that you remove the poles out of the loops in your tent.

After that, fold the poles in the appropriate manner. Some tent poles are made up of several parts that may be joined together to form lengthy poles. If this is the situation with your poles, remove the segments that are affixed to the poles and store them in their pole bag.

Shake up the camping tent

Cleaning up the tent may not always imply that you are finished. As amusing and strange as it may sound, you must pick up your tent and shake it well before using it. The only reason for doing this is to clear away any debris that may have accumulated on the tent.

Make the tent flat

It’s possible that cleaning up the tent doesn’t indicate you’re finished. Although it may seem absurd and strange, you must take up your tent and shake it vigorously before continuing. Only debris that may have accumulated on the tent will be removed in this manner.

Fold up the tent

Cleaning up the tent does not always imply that you are finished. As amusing and strange as it may sound, you must take up your tent and shake it well. The only reason for this is to clear away any debris that may have accumulated on the tent.

Pack up the fly

Now that you’ve finished working on the main tent, you’ll need to straighten the fly and fold it lengthwise so that the outside portion of the fold is within the fold. This is something that two people should have no trouble putting together.

Folding the fly

Now that you’ve finished working on the main tent, you’ll need to straighten the fly and fold it lengthwise so that the outer section of the fly is contained within the fold. The execution of this is something that two persons should have no trouble accomplishing.

Put everything together

Place everything out in front of the tent, starting with the fly nearest to you and working your way out to the tent poles, pegs, and anything else that is farthest away. Before you do anything, you must completely roll in the fly, insert the tent poles, and roll it again. Put the pegs back in and roll it up once more. Incorporate any remaining ingredients and roll till the finish, tying it properly at the end. When rolling the tent, make sure to roll it firmly since allowing too much air inside the tent can cause issues when folding, as the tent may not fit into the bag.

Put the tent in the bag

Having carefully folded your tent and stowed away all of your belongings, there isn’t much more left to do except put your tent in a bag and wait for the next camping trip, whether it’s with your friends or by yourself. When it comes to folding a normal tent, the methods outlined above are the most basic. Tents, on the other hand, come in a variety of styles. The following are the procedures to folding some of the most common tents available on the market:

Folding a Cabin Tent

A cabin tent is fairly large and can accommodate groups of up to ten individuals. While putting it together may not be difficult, getting it inside the tent bag is a different story entirely. If it is not folded correctly, it may not fit properly in the bag. Several factors should be taken into consideration when folding a cabin tent:

  • Remove moisture and dirt from the fabric by wiping it on both the inside and outside of the cloth. Take down the tent poles and pegs
  • The tent should be laid down level on the ground in the shape of a square or rectangle. In order to prevent lumps from forming, fold the tent in half and ensure that the tent is entirely flat. Fold the tent in half once more to create a rectangle that is longer than it is wide. Confirm that the tent bag is the correct length. If the width of your tent after it has been folded is more than the length of the bag, you will need to fold the tent again. Begin by folding the tent in half, starting from the narrow end, and putting it in the bag.

Folding a Backpacking Camping Tent

This tent is a favorite of individuals who want to travel light while camping. So that’s how you fold a backpacker camping tent, step by step.

  • The tent should be cleaned and dried thoroughly to guarantee there is no mold growth and that it does not have a foul smell
  • Whether it’s pins or stakes, Remove anything that has been used to secure the tent to the ground so that it may be moved. It is important to keep the pins and stakes in a different location from the tent bag in order to avoid ruining the fabric of the tent. Fold the tent poles after removing them from the loops. As long as the poles can be tied together or placed in a different bag all together, they should be OK
  • Otherwise, they should be stored separately. The tent should be shaken to get rid of any remaining dirt and to straighten the cloth. Place the tent on the ground so that the entryway is towards the top of the structure. Fold the bag in half starting from the sides and working your way towards the middle. Check to see that there is no air trapped in the folds or lumps of fabric. Roll inside the tent starting from the spot that is furthest away from the entrance. Finally, tie it securely and place it in the tent bag to finish it.

Folding a Dome Shaped Tent

In the event that you want a dome-shaped tent, here are some tips on how to fold this sort of tent.

  • Pack the flysheet in the trunk of the car. Before you do anything, make sure the flysheet is straight. Fold the fly in half lengthwise, with the outer section of the fly folded within the fly. Fold the fly in half lengthwise again, this time with the outside section facing inside. If you want to do it well, you can utilize a second hand. Fold the fly in half. Retuck the fly’s ends to the nearest pole, then collect the fly’s ends towards the center and fold it in once more. Repeat with the other fly. If everything is done correctly, the flysheet of each pole should be the same width. The fly is being rolled up. Begin by working your way up to the top of the fly, concentrating on the lightest section of it. Roll it up firmly and secure it with a knot. When folding the tent, the tighter the fly is, the simpler it is to fit it into the bag. The tent should be spread in the same manner as it was built. Make certain that all zippers are completed
  • Make the necessary adjustments to the roof part. The center roof mounts will serve as excellent support rods for the structure. Pulling the canopy can help to ensure that it is completely flat. Don’t be concerned about the surplus fabric. Simply place it over the area of the rear entrance and fold the vestibule down to the floor. Fold the vestibule so that it lies over the body of the tent, with the top portion of the vestibule resting on top. If your tent does not have a vestibule, you may skip this step and just fold the tent. Fold each edge of the tent towards the center, then fold it in half again to reduce the size of the tent to a quarter of its original size
  • Gather everything together. Place everything on the front section of the tent by first placing the fly sheet, poles, pegs, and any other items that you want to use in the tent. Adding one element at a time, rolling once, adding another and rolling again, and lastly rolling the end of the tent and tying it properly is the best way to go about this process. The tent should be rolled extremely tightly to eliminate unwanted wrinkles while folding and rolling, since any extra air will cause the tent to not fit in the bag.

Useful Tips When Folding a Tent

Roll up your tarp and head to the beach. Before you do anything, make sure the flysheet is straight! Fold the fly in half lengthwise, with the outer section of the fly folded within the center. Make another longitudinal fold in the fly with the outside section facing inside. Repeat the process for the second fold. To accomplish this properly, you can utilize a second hand. Using the fly, fold it in half. Retuck the fly’s ends to the nearest pole, then collect the ends of the fly towards the center and fold it in once more.

  • The flysheet of each pole should be the same width if the job is done properly.
  • Begin by working your way up to the top of the fly, concentrating on the lightest section.
  • Tent folding is made simpler by tying the fly as tightly as possible before putting it in the bag.
  • Double-check that all zippers are properly installed; Make the necessary adjustments to the roof component of the structure.
  • The cover should be pulled taut to ensure that it is completely flat.
  • Lay it over the back door area and fold the vestibule.
  • To set up a vestibule, fold it so that it lies over the body of the tent, with the top section of the tent laying on top of the bottom part.
  • Fold each side of the tent towards the center, then fold it in half again to reduce the size of the tent to a quarter of its original size; pack it all together.
  • Adding one element at a time, rolling once, adding another and rolling again, and lastly rolling the tent’s end and tying it properly is the finest method to go about this process.

The tent should be rolled extremely tightly to eliminate unwanted wrinkles while folding and rolling since additional air will cause the tent to not fit in the bag.

  • Make a flysheet out of newspaper. Before doing anything, make sure the flysheet is straight. Fold the fly in half lengthwise, with the outside section of the fly folded within the fold. Fold the fly lengthwise once more, this time with the outside section facing inside. If you want to do it properly, you can utilize a second hand. Fold the flier in half. Retuck the fly’s ends to the nearest pole, then collect the fly’s ends towards the center and fold it in once more. If the job is done properly, the flysheets of each pole should have the same width. Rolling up the fly is a good idea. Begin by working your way up to the top of the fly, focusing on the lightest section of it. Roll it up firmly and secure it with a string. When folding the tent, the tighter the fly is, the simpler it is to get it in the bag. Spread the tent in the same manner in which it was first built. Ensure that all zippers are completed
  • Make necessary adjustments to the roof part. The central roof mounts will serve as excellent support rods for the whole structure. Pulling the cover will guarantee that it is completely flat. Don’t be concerned about the extra fabric. Simply place it over the area of the rear entrance and fold the vestibule down. Fold the vestibule so that it lies over the body of the tent, with the upper section of the vestibule resting on top of the body. If your tent does not have a vestibule, do not worry about this step
  • Simply fold the canvas. Fold each side of the tent towards the center, then fold it in half again to reduce the size of the tent to a quarter of its original size
  • Pack everything together. Prepare the front section of the tent by first laying the fly sheet, poles, pegs, and any other items you want to use. Adding one piece at a time, rolling once, adding another and rolling again, and lastly rolling the end of the tent and tying it properly is the finest method. Roll the tent very tightly to eliminate unwanted wrinkles while folding and rolling, since additional air will cause the tent to not fit in the bag.
See also:  How To Tear Down A Coleman 10' Tent

Importance of Knowing How to Pack Away a Tent

Prepare the flysheet. Before anything else, make sure the flysheet is straight. Fold the fly in half lengthwise, with the outer section folded inside. Fold the fly in half lengthwise, this time with the outside section facing inside. If you want to do it well, you can utilize a second hand; The fly should be folded. Tuck the ends of the fly to the nearest pole and collect the ends of the fly into the middle, folding it in once more. If the job is done correctly, the flysheets of each pole should have the same width.

  1. Begin at the top of the fly, concentrating on the lightest component of the fly.
  2. The tighter the fly is, the easier it is to get the tent into the bag; folding the tent.
  3. Make certain that all zippers are completed.
  4. The middle roof mounts will serve as excellent support rods.
  5. Do not be concerned about the surplus fabric.
  6. Fold the vestibule so that it lies over the body of the tent, with the top section of the vestibule resting on top.
  7. Fold each edge of the tent towards the center, then fold it in half again to acquire a fourth of the original size of the tent; pack everything together.
  8. The easiest method to accomplish this is to add one thing at a time, roll it once, add another and roll it again, and then roll the end of the tent and knot it properly.

Final thoughts

All campers must be able to pitch a tent, which is an essential skill. Spending the night in the woods with a bunch of friends is a great way to spend the evening. While the experience may not have been as warm and cozy as you would have liked, the memories made are ones that should be treasured. A large majority of campers are familiar with the feeling of having to pack up their tent. Typically, people collapse the tent and roll it inside the tent bag, however this never results in the tent bag fitting properly.

Check out our simple instructions on how to create a DIY camping tent for inspiration if you want to save even more money.

How to Fold Up a Pop Up Tent (In 4 Easy Steps!)

As a result of its ease of assembly and portability, pop-up tents have gained widespread popularity. However, these shelters have a dirty little secret that I was completely unaware of until after I purchased one: they are very tough to put back into the bag! Despite my best efforts, I couldn’t figure out how to fold a pop-up tent despite consulting the manufacturer’s instructions. I sat in the dining room for over an hour trying to figure it out, with my wife giving me pitying glances as she went by.

Then I came across a video of an elderly Asian woman who gently Tai-Chi’d her pop-up tent back into its bag. It just took a couple more tries for me to have it “in the bag” now that I was armed with additional knowledge. In order to save yourself a lot of effort and heartache, continue reading!

How To Fold Up a Pop Up Tent (Step-by-step)

Alternatively, you may watch the video below and follow along with the processes given out in the subheadings below, which I have split down into sections.

Pre-folding tips

Do yourself a favor and give your shelter a good brushing to get rid of any sand or debris that has accumulated. Some pop-up tents are tiny and light enough to be picked up and shaken, but if you have a dustpan and brush, you can get away with it. During this procedure, wind is not your friend, and it is quite beneficial to have a second person to assist keep things under control in these scenarios. If you’re on your own, keep some heavy objects close by to assist keep things from blowing away in windy situations.

Step 1 – Make it flat

To make your tent flat, bring the edges of your tent together and tape them together. A symmetrical manner of pressing the shelter together will almost always be the only way it can be done in most cases. If it is refusing to fold the way you want it to, or if it has an unusual form, try pushing it flat along a different axis to see if that helps. Please refer to the graphic below if any of the above terms do not make sense.

Step 2 – Start folding in half

Bring the other end towards you, following the axis depicted in the image below, while kneeling on one end of the rope.

Step 3 – Fold over to create circles

Roll the end that is heading towards you beneath itself, and you’ll see that a handful of circles develop as a result of your actions. Bring these circles together such that they are stacked on top of one another.

Step 4 – Secure and bag up

After folding the tent and placing it in the carry bag, stand back and watch everyone’s jaws drop as you walk off the beach, knowing that you have just accomplished the seemingly impossible.

Other pop up tents

If you have a pop up camping tent (as opposed to a simple pop up tent), the principle is quite similar, with the exception that you want to make a burrito shape first, and then pull the two ends together, which will automatically fold into circles as a result of the natural folding. Take a look at this guy demonstrating to his tent who is in charge.

How to Re‐Pack a Pop Up Tent

Documentation Download Documentation Download Documentation The use of pop-up tents may make camping a cinch! When it’s time to pack up your tent, make sure it’s clean and dry, and pull the grounding stakes out of its grounding system. Pull the upper arches of the tent together and fold it over as neatly as you can to make it more compact. If you fold it securely enough, your pop-up tent should be able to fit precisely back into its carrying case.

  1. 1 Make sure your tent is entirely dry before setting up. Unless it has rained on your tent, you should allow it to dry completely before packing it up. If you don’t have time to wait, use a clean, dry towel to wipe away any remaining moisture from the tent. In addition, before packing up your tent, make sure to thoroughly dry the underside of the tent.
  • First and foremost, make certain that your tent is absolutely free of moisture. Unless it has rained on your tent, you should let it air dry before putting it away. Instead of waiting, you may use a clean, dry towel to wipe away any remaining moisture. Also, when packing up the tent, make careful to dry the underside of the tent.
  1. 2Clean the surface with a brush to remove dirt and debris. Make every effort to thoroughly clean the outside of your tent before storing it up. Using a tiny brush or a dry towel, remove any dirt, small rocks, sticks, insects, or other debris from the tent’s interior. You may also use a broom or a snow brush to get to the corners of the tent that are difficult to reach. Advertisement
  2. s3 Allow your tent to air out for one hour before putting it away. A closed tent can get musty or wet throughout the course of a camping trip if it is not ventilated. It’s best to open the tent entrance and let it air out for at least an hour before you pack it up to avoid smells or mold growth. This will also help you to air out your sleeping bag, pillow, and any other stuff you have within
  3. 4 Take the stakes out of the earth using your hands. You will need to untether your tent first before you can put it away properly. Remove all of the metal stakes that are holding it to the ground around the perimeter of the structure. 5Remove the tarp, if your tent has one, and store it in your tent bag or a small zip lock bag until you’re ready to reassemble your tent. An included tarp will assist to protect your tent from rain and will also provide additional shade if you need it. Pulling the tarp away from the tent after you have removed the grounding poles is a good idea. Then, fold it up nicely and place it to the side. Advertisement
  1. 1- Take hold of the tent’s two top points and draw them together as tightly as you can. Stand on one side of your pop-up tent, perpendicular to the tent door, and look through the tent at the other. Locate the two high arches that will form the apex of your tent’s top point. Grab the two top points and pull them together in one hand, keeping them together with the other hand
  2. 2Take the rear end of your tent and fold it in half so that it meets the center. Grab the smaller arch at the top of the rear of your tent with your free hand and secure it in place. Increase its height till it meets the two points that have been held together thus far. Then, using your other hand, grab all three spots
  3. 3 Bring the front arch all the way together so that it meets all the other points. As you fold your tent, make sure the tent entrance is unzipped to allow air to escape as you do so. Grab the top of the arch that spans the opening above the entrance with your free hand. Tent up the front of the tent and fold it inwards toward the remainder of the tent.
  • Ideally, your pop up tent should be in the shape of a taco at this time.
  1. Your pop-up tent should be in the shape of a taco at this stage.

Fill in the blanks with your question and email address to be notified when it is answered.SubmitAdvertisement200 characters remaining

  • Depending on the model of your tent, the instructions for folding it may differ. Before you use your tent, make sure you read any directions that came with it.

Thank you for submitting a suggestion for consideration! Advertisement

About This Article

Summary of the ArticleX Pop-up tents can make camping more convenient, but you’ll need to follow a few basic guidelines to re-pack your tent properly. If your tent becomes soiled or damp, just wipe it down with a towel, brush it off, or wash it with mild soap and water to clean it. After you’ve cleaned your tent, open it up to allow it to air out to minimize the development of musty aromas. After you have removed the poles and any tarps that have been placed over your tent, you may begin folding it.

Then, take the rear end of the tent and fold it in half, as well as the front arch, so that they meet in the center.

Twist it slightly so that the arches form two circular forms, and then fold them over each other to close the package.

You are now free to put the tent back into its carrying bag. Continue reading to find out how to lock and store your tent if you don’t have a bag for it already. Did you find this overview to be helpful? This page has been seen 91,539 times thanks to all authors who worked together to create it.

Did this article help you?

This post includes affiliate links for your convenience. Despite the fact that we enjoy camping, it can be irritating to attempt to put your tent back in its bag. I wish manufacturers would take this into consideration when packaging their products. The process of putting the tent, poles, pegs, and fly sheets back into the bag has become really frustrating for me. I’ve had to walk away, take a few deep breaths, and utter a few choice words to get my bearings. I’ve snapped at Nick on a number of occasions, and I feel terrible about it since it wasn’t his fault.

When attempting to repack your tent into its original bag, open all of the openings to release as much trapped air as possible before closing the bag.

Rolling your tent securely from the rear to the front is a good place to start.

Place the bag at one end of the tent and slowly unroll the bag over the canvas until it is completely stuffed.

1 –Inner lining of tents – sleeping compartments

Remove the inner linings from your tent before you fold it up and store it. Your tent’s sleeping chambers are located in this area.

2 –Open all doors

Open all of the doors and vents in your tent because you need to get rid of all of the trapped air inside before you can begin to collapse the structure.

3 –Unclipping poles, pegs and guy ropes

Begin by removing as much air as you can from the back of your tent and working your way toward the front. Remove your poles from the ground pegs and all of the man ropes and pegs that were attached to them. Make sure you have a bag nearby so that you can quickly put away all of the pegs as you remove them to avoid any being left behind. The pegs are always passed on by me to Nicholas, who is responsible for cleaning them of any filth before they are bagged. This saves me the time of having to do it while we are at home together.

Some tents feature velcro linked to the poles, which makes it easier to tie the poles to the tents.

Make an effort not to put any strain on your poles.

When your tent is completely level on the ground, remove any pole clips and then disassemble and store away your poles.

4 –Levelling your tent ready for packing away

Maintaining your tent’s position on the groundsheet, try to square the tent.

Remove any trapped air from your tent by opening your doors and laying them as flat as possible on the ground. Don’t be concerned if there is still some trapped air in the system. When you start rolling, the object will be removed.

5 –Using your tent bag as a measure for packing away

Set up your tent bag such that the length of it runs parallel to the width of the tent. Most people will fold their tent into thirds before doing this, but I think that measuring from the beginning is easier and more accurate. Fold your tent gradually in proportion to the length of your luggage, but do not fold it to the precise width of your bag, leaving a space on each end. Otherwise, you will not be able to effectively place your bag in your suitcase or close your suitcase. Continue to fold your tent until you have one strip of the tent that is ready to roll.

To keep Nicholas active and to prevent him from becoming bored, when we fold pieces of the canvas, he will roll from the rear of the tent to the front, therefore aiding in the removal of any trapped air.

6 –Preparing your tent bag

We have a soft long cylinder type tent bag, rather than a rectangle tent bag, which is what we used for our tiny tent. First, I prepare the cylinder tent bag by rolling it from the top outwards to a width of around one hand breadth. In order to make it simpler to pack your tent, it is recommended that you roll your bag rather than trying to shove your tent into its’ bag when it is fully extended.

7 –Rolling to your tent

It is still necessary to roll your tent from the back since you want to eliminate any excess air from the tent. Roll your tent firmly from one end to the other until you reach the other end. Make an effort not to allow the breadth of your rolled tent to expand. This is optional, however you may set your pole and peg bag on top of your tent and use it to assist you in rolling your tent up. This is something I don’t do since it’s tough for me to perform a tight roll. My pole and peg bags are placed into the tent bag once the tent has been set up inside it.

See also:  How To Use A Grow Tent For Vegetables

8 –Placing your tent into its bag

As a precaution, I will sit on one end of the tent to ensure that it is firmly coiled. Setting the tent bag’s top portion over the tent’s bottom portion Gradually lowering the tent bag and unfolding it as I go is my method of lowering the tent. Don’t be scared to push down on your tent to ensure that it is completely contained within your bag. Try not to stuff the entire tent into a rectangular bag if you just have a little amount of space. Place the first part of the tent first, and then gradually bring in the remaining portions.

You may either gently push your tent into the bag or lay your figures between the tent and the bag while you zip it up.

What to do if your tent is wet

You shouldn’t be concerned about packing your tent inside its tent bag if it is damp since you will simply have to take it back out to dry when you get home. It should be rolled up in your groundsheet and placed at the bottom of your car’s trunk. Dry your tent at home over a period of 2-3 days and thoroughly clean it before putting it in your tent bag.

How To Correctly Pack Away Your Tent

To properly pack away your tent, whether you’re about to leave on a vacation or returning from one, you must first learn how to set up your tent correctly. Expeditions, festivals, the Duke of Edinburgh’s Award, or simply a camping trip, tents come in a variety of forms and sizes, and each has its unique knack for putting them away. As a result, you must take care while packing your tentaway, or you may find yourself regretting your decision on your next vacation. Winfields Outdoors has put together this guide on putting away a tent to assist you.

Ensure that your tent survives the test of time no matter where you go by paying attention to each of these factors. Continue reading to learn how to properly pack away your tent, as well as other advice to ensure that your tent will survive for many more adventures to come.

Why is it so important to pack your tent away properly?

Simply said, if you don’t properly store your tent, when you go to retrieve it for next year, it may be damaged or have other difficulties that are too late to be repaired before the next season begins. It is possible that whatever issues that your tent has when it is put away will still be present, and that it may even have developed new ones throughout the process of packing it away. More information may be found at: When it comes to camping, it is critical to thoroughly inspect your tent. So, what is the proper method of putting it away?

Dry your tent before it’s packed away

That is to say, if you don’t properly put up your tent, when you go to pull it out for next year, it may be damaged or have other difficulties that are too late to cure. If your tent has difficulties when it is packed away, those problems will still be there, and it is possible that it may have developed new ones throughout the process of packing it away. For further information, please see this link: The Importance of Inspecting Your Tent Before Camping So, what is the proper method of putting everything away?

Check for rips, tearsbreaks

Modern tents are quite durable and can sustain a significant amount of wear and tear without breaking down. However, they are not invincible, and the occasional rip or tear may occur from time to time. As a result, it’s critical that you take care of them before you put your tent away. Furthermore, the last thing you want is to arrive at your campground, attempt to pitch your tent, and then discover that you have a damaged pole or a hole in your groundsheet. More information may be found at: The Definitive Guide to Tent Maintenance Maintenance When you get home, thoroughly inspect the whole tent, including the poles, for signs of wear or damage.

At Winfields, you may get replacement tentpoles and guy lines, as well as repair kits that include items such as tape.

Fold or roll your tent properly

Most contemporary tents are quite durable, and they can resist a significant amount of abuse. It should be noted, however, that they are not indestructible, and the odd rip may occur sometimes. As a result, it’s critical that you take care of these issues before you pack up your tent. Not only might the rips develop worse with time, but the last thing you want is to arrive at your campground, attempt to pitch your tent, and then discover that you have a damaged pole or a hole in your groundsheet.

If the damage is minimal, you may be able to repair it yourself; however, if the damage is more serious, it may be necessary to replace a portion of the tent or the entire tent altogether.

At Winfields, you may get replacement tentpoles and guy lines, as well as repair kits that include items such as tape, for your tent.

Bag pegs and poles

Modern tents are quite durable and can survive a significant amount of use and abuse. However, they are not invincible, and they may occasionally suffer a rip or two. As a result, it’s critical that you take care of these issues before you put your tent away. The rips may worsen with time, and the last thing you want is to arrive at your campground, attempt to pitch your tent, and discover that you have a damaged pole or a hole in your groundsheet. More information may be found here: Tent Repair: The Definitive Guide Maintenance When you get home, thoroughly inspect the whole tent, including the poles, for signs of damage.

Winfields sells new tentpoles and guy lines, as well as repair kits that include items like as tape.

How to care for a tent – Tent Tips

  • Modern tents are quite durable and can resist a significant amount of wear and tear. However, they are not invincible, and the occasional rip or tear will occur from time to time. As a result, it’s critical that you take care of them before you pack up your tent. Not only might the rips develop worse over time, but the last thing you want is to arrive at your campground, attempt to pitch your tent, and then discover that you have a damaged pole or a hole in your groundsheet. More information is available at: The Definitive Guide to Tent Repair Maintenance When you get home, carefully inspect the whole tent, including the poles, for signs of damage. If the damage is minimal, you may be able to repair it yourself
  • However, if the damage is extensive, it may be necessary to replace a portion of the tent or the entire tent. Winfields carries new tentpoles and guy lines, as well as repair kits that include items like as tape.

More information may be found at: Best Way to Waterproof a Tent. If you can’t find the bags, use whatever you have on hand to wrap them up and keep them safe while you search for them. Take a look at our whole array of tent accessories or our entiretents collection, which includes: Large Tents|Family Tents|Polycotton Tents|Tents by Brand|Tents by Size To get you ready for 2020, check out more articles on theWinfields Blog. Don’t forget to check out our camping blog for more articles like this.

How to Fold Pop-Up Tent? – Guide You Need To Read

Continue reading: The Most Effective Method of Waterproofing a Tent. You may use whatever you have to wrap the bags and protect your tent if you can’t find the bags themselves. See the whole variety of oftent accessories or the entiretents collection for inspiration, which includes: The following categories are available: Tents by Size, Family Tents, Polycotton Tents, and Tents By Brand. To get you ready for 2020, check out more articles on theWinfields blog. Don’t forget to check out our camping blog for more articles like this.

Purchasing an Air Tent

How to Fold Pop Up Tent

Before we get started with the tutorial, I’d want to point out a few of things. There are various different kinds of pop-up tents that you may come across. There are several types of tents available, including a camping tent, a dome tent, a sun shelter, a beach shelter, a portable tent, and a shower tent. All of these tents are available in a variety of sizes and somewhat varying forms.

Most pop-up tents may be folded in the same manner, however the method of folding varies from one tent to the next. Some of the steps may need to be adjusted, but you can always use them as a stepping ground for the rest. If it is all clear, you and I can dive straight into the guide right now!

Step 1 – Prepare the tent for folding

I’d want to share a few thoughts with you before we get started with the tutorial. Pop-up tents come in a variety of shapes and sizes, and you will come across numerous different sorts. There are several types of tents available, including a camping tent, a dome tent, a sun shelter, a beach shelter, a portable tent, and a shower shelter. There are a variety of sizes and forms available for all of these tents. While the majority of pop-up tents may be folded in the same manner, there are some that need a slightly different method of folding.

If everything is clear, you and I can go right into the guide!

Step 2 – Start folding the tent

Unziping the tent’s door or two doors should be the first thing you do after setting up your tent. This will let the air from the interior of the tent to escape, making it easier for you to fold the tent when you are through. After that, you may fold the tent to form an oval shape using your hands. Take hold of the tent’s back, since you will be starting your journey from there. Bring the rear pole to the center pole, and then put it back where it belongs. If you find it difficult to do so, you can use one hand to grip the rear pole while the other hand grabs a hold of the center pole to make it easier.

If there is any lingering air in the tent, make sure to get it out as soon as possible after closing it.

Step 3 – Lift and rotate the tent

When you have the tent poles in your hands, it should be quite simple to hoist the tent. It would be beneficial if you placed it on the side, so that it stands vertically. Make certain that you have a tight grasp on the tent throughout the day.

Step 4 – Fold and slide the rings

You should then reach your hand towards the top of the tent and draw it as near as you possibly can to your feed once you have it in a vertical position. Because it will be on the ground, it should be easier to manage the folded tent at this point in the process. Next, you should examine the two circles that are part of thetent frame to ensure that they are not broken. They should be overlapping at all times. It is recommended that you stack the rings on top of one another. After you’ve finished, the tent will take on the shape of a huge circle.

Step 5 – Bag the tent

Using an elastic band, which should be included with your tent, you can keep the tent in a folded position. This will make it much easier for you to pack up the tent and store it in the bag. After you’ve completed these steps, your tent will be ready to be packed into your car or bag.

How to Fold a Pop-up Tent into A Circle?

Most pop-up tents can be folded into a circle because of the way they are designed. When planning a camping vacation, pop-up tents are a terrific option to have on hand in case you want to retire for the night. It only takes a minute to get them up and running! It’s necessary to fold your tent after spending the night inside, and I propose that you fold it into a circle. To accomplish this, begin by thoroughly washing and air drying the tent. Then take off all of your excess layers, as well as any items that may have been in them.

Turn the tent to one side after you’ve got the top poles in your hands.

Next, the tent would be sealed with a rope or something similar.

If your tent is circular in form, you will likely find zippers around the poles that may be zipped together to close the tent.

As a result, if your tent is equipped with zippers, use them to close it. Make certain that you are not grasping onto the fabric with the zipper because this might cause harm to it. Take special care when packaging the package!

How Do You Fold A Big Pop-Up Tent?

Since the design permits it, the majority of pop-up tents fold into a circle. When planning a camping vacation, pop-up tents are an excellent option to consider if you intend to stay the night. Putting them together takes about a minute! After you have spent the night in the tent, you will need to fold it, and I propose that you fold it into a circle. This is accomplished by first washing and drying the tent outdoors. Then take off all of your excess layers, as well as any items that may have been within them.

  1. Turn the tent to one side when you’ve got the top poles in your hand.
  2. Next, the tent would be sealed with a rope or other type of elastic bandage.
  3. If your tent is circular in form, you’ll likely find zippers around the poles that may be zipped together to close the tent completely.
  4. Make certain that you are not grasping onto the material with the zipper because this might cause harm to it.

How To Fold A 4 Sided Pop-Up Tent?

4-sided pop-up tents are often a little bigger in size than normal pop-up tents of this type. While folding this sort of tent may prove more challenging, it is not impossible! This sort of tent can have two doors, however it is most commonly found with only one. When you intend on folding it, make sure to keep the door open to ensure that nothing gets stuck within. Due to the fact that this is a four-sided tent, it will have four poles. When folding it, you should grip the four poles together and allow all of the air to escape while continuing to hold on to the object.

It is possible that you may have to pull, but it should not be too difficult.

After that, you may either bag your tent or leave it in its current state and store it immediately.

Continue to keep the tent in this manner until you need to use it again!

Wrap Up

Pop-up tents with four sides are often a little bigger in size than conventional tents of this type. It is likely that folding this style of tent would be more difficult, but it is not impossible! It is possible to purchase this sort of tent with two entrances, although the majority of the time it is only one. When you intend on folding it, make sure to keep the door open to ensure that nothing gets stuck within. It will contain four poles, in order to accommodate the fact that this is a 4-sided tent.

Afterwards, flip the tent around and bring one of the ends up near to the other end.

It is necessary to use elastic bands to hold the ends of the tent together once they have been brought together.

Afterwards, you may either bag your tent or leave it in its current state and store it immediately after use. It shouldn’t be too difficult to put everything away. This is how you should keep the tent stored until you need to use it again!

Hello, my name is Andrew Mullen, and my fascination with the great outdoors began when my grandfather and father used to take me along with them on camping vacations when I was a child. We used to go trekking in the woods, and after a hard day of hiking, we would set up camp and spend the evenings around a camp fire. This blog is intended to be inspirational and I hope you enjoy it. Who knows, maybe we’ll run into each other at a camping someplace in the woods and exchange a few stories? Andrew Mullen’s most recent blog entries (see all)

Leave a Comment

Your email address will not be published. Required fields are marked *