How To Fix Tent Pole Elastic

How to Repair Tent Pole Elastic Cord (Re-thread) – the Easy Way

Determine the diameter of the cord that has to be replaced. When it comes to low-cost tents, this will often be approximately 2mm in diameter, which is not particularly sturdy or long-lasting. Depending on how large the opening diameter is of the pole, you may be able to utilize a thicker diameter than you originally planned. I increased the diameter of the cable on my tent poles from the standard 2mm to 3mm. The cable may be purchased on eBay for a reasonable price. I live in the United Kingdom and purchased 10 meters for around £3.

In order to set up a two-person dome type tent with two tent poles, you’ll need at least ten meters of space.

In an updated version of this post, I measured the original cable and discovered that it was half the length of the poles after they were completed.

Step 2: Find Your Threader

A threader, which you will need to obtain, will be required to feed the cord through. An nice metal threader was discovered within an old windshield wiper, which I was able to save. Consequently, when it is time to replace your windshield wipers, save them or borrow some from your neighborhood auto repair shop. The wiper blade assembly has two strips of metal that span the length of the wiper blade. You must remove these strips of metal from the wiper blade assembly. The greatest wiper blades are those from a saloon vehicle or a van since they have the longest blades available.

Please keep in mind that my photo displays a windscreen wiper, however it is too short.

Metal inserts are uncommon to be found in the lower-priced wiper blades.

Step 3: Join Threader to New Cord

It is now necessary to connect the threader to the new cable. This is accomplished by joining the threader and cable together using a butt joint and then fastening the junction with a very little quantity of adhesive tape. In this shot, I used one revolution of double-sided adhesive tape. Use only a little amount of tape, as too much will cause the threader to drag and cause it to stick to the inside wall of the tent pole.

Step 4: Remove Old Elastic Cord and Re-thread New Cord

Push the threader through the pole aperture after you have cleaned out the old cable from the poles. When it is sliding smoothly, slowly draw the threader through to the other end, where it should poke out the other end. Remember that if this is tough, it is likely that you have too much adhesive tape. Having passed through, pull the threader back through and continue to thread all the remaining poles.

I use up the old elastic cord because I’m a thrifty person. lanyards and neck cords can be made out of the old cord if necessary. I strung all of my USB storage sticks from the old cord that had frayed.

Step 5: Tension Cord and Tie Off the Ends

Trial and error is required to achieve the desired tension, so after threading the entire pole, experiment with your cord tension. The tension must be light enough to allow the poles to be pulled apart, yet firm enough to keep them together when threaded through the tent’s opening. The figure of eight knot is my preferred method of tying off the ends because it is a bigger knot that is also easy to alter. A more substantial knot at the end will last longer. You can then cut the cord after the tension has been reached to your satisfaction.

Step 6: Finished – Store Threader for Next Repair

You should have completed the repair of the tent poles by now. Remember to have your threader handy for when you need to repair your tent! I hope you have found this information beneficial. Thank you for taking the time to watch!

Be the First to Share

The elastic shock cord on your tent poles has deteriorated and has become brittle, making it no longer flexible. Given that new poles can cost up to $100 or more, why not simply replace the cord, which costs less than ten percent of the price of new poles? It’s been years since I’ve used my North Face Rock 22 two-person tent (which has two identical poles), and the elastic cord within the poles has become brittle and no longer retains its flexibility. I had purchased the tent brand new for around $200, and replacement poles were going to cost an additional $150!

I just needed 30 minutes and a pint of beer to get my tent poles back to their original condition!

You’ll need at least the whole length of all of your poles combined to complete the task.

a pair of scissors or a knife Sharpie or Marker for Measuring Tape Matches or a lighter are recommended.

Step 1: Cut the Cord and Remove the Grommet Pegs

Take a deep breath in and out. Pulling two parts of the pole apart and cutting the rope will do this. This will cause the pole to divide into its distinct parts (Mine has 8 sections per pole, and only the two end sections are different, so I made sure to keep those separate). Remove the peg from the pole end and you should be able to see the standing end of the cord, which has been knotted and linked to the peg. Because my pegs were threaded, I had to detach them from the pole sections in order to use them.

Step 2: Measure Your Pole(s)

Following that, you’ll want to take measurements of your poles so that you can determine how long your rope should be. Because my tent has two poles that are exactly the same length, I only had to measure once. If you have many poles of varying lengths, you will need to repeat this step for each pole in your set. Measure the length of your pole from end to end; this will be the length of your rope when it is fully stretched. My experiments with the elasticity of the cable led me to the conclusion that for every foot of relaxed cord, I would receive 1′-4 of length “because of a stretched chord To get the final length (the length of the pole, hence the ultimate stretched length), we must multiply it by 75% of the original length.

Take the length of your pole in inches and multiply it by 0.75.

My poles are 152 inches in length, hence my measurement is as follows:152 inches * 0.75 inches = 114 inches” This is the spot where I put my relaxed chord marker.

Please keep in mind that you should not cut the cord just yet! It is quite difficult to feed a 114″ cable into a 152″ pole because of the length difference. Inquire as to how I know this.

Step 3: Thread Your Peg and Knot the Cord

Feed the standing end of the cable (the end that is marked with a ‘zero’ on the tape measure) through the hole in the grommet peg and secure it with a rubber band. Draw the thread through a basic binding knot about 2 inches from the end and tighten it. Your peg should now be in the middle of the knot and the long end of the rope, as seen below. In order to avoid tripping, feed the cord through the first part of pole and continue until all portions are attached to the cord. Check to see that the pole portions are aligned appropriately so that they will fit together as intended before continuing (male end toward female end for each joint).

The long end of the cord should be stretched so that it reaches the mark you created earlier while the pole pieces are joined in the manner in which you would build the tent.

In this stage, the pole should be beginning to take form.

Step 4: Cut/Singe the Cord and Insert the Pegs

In order to use the grommet peg, feed the standing end of the cord (the one that is marked with a “zero” on the tape measure) through the hole in the peg. Draw the thread through a basic binding knot around 2″ from the end and tighten it. Now, your peg should be positioned halfway between your knot and the long end of the string (see illustration). In order to avoid tangling, feed the cord through the first part of pole and continue until all portions are connected to the cord. Check to see that the pole portions are positioned appropriately so that they will fit together as intended before proceeding (male end toward female end for each joint).

Extend the long end of the cable until it meets the mark you established earlier while the pole pieces are attached as though you were building the tent.

It should be starting to take shape at this stage.

Be the First to Share

There are various little components in a tent that might fail, but these do not need the purchase of a completely new unit. Tent pole shock cords are susceptible to failure, deterioration, and brittleness with time, and finally loss of their elastic qualities. Your tent pole may no longer operate properly if the shock cord is no longer functioning properly. You may believe that new tent poles are required. Purchasing new tent poles, on the other hand, may be quite expensive, and there is a lot more affordable option.

It is simple to replace the shock cord in your tent pole; all you need are a few simple components and a positive mindset.

We’ll also talk about why shock cords are vital, as well as some preventative actions you may do to avoid more harm.

– Continue reading to learn more about all of this and how to replace the shock cable in your tent pole in a professional manner. If you know how to mend a broken tent pole in the field, a broken tent pole in the field does not have to be a reason for panic.

What is a tent shock cord and why is it important?

Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.

Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.

What you need to replace the shock cord in a tent pole

Make sure you have all of the materials you’ll need before starting to work on your tent repair. A replacement shock cord may be purchased at your local camping store, and there are several companies who sell shock cords online as well. You will require the following materials:

  • The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
  • Scissors or a sharp edge
  • Measuring tape
  • Sharpie or marker pen
  • A lighter or matches to melt the ends of the wires Tape for masking

How to replace a faulty shock cord in a tent pole

The moment has come to get started on mending your shelter now that you have all of the equipment you need, as well as some new shock cable to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will see that your tent pole will come apart into its many components after the cable has been severed.

  1. Because it’s probable that the pole portions in the middle are similar, the end pieces where the rope is knotted are the most critical parts to avoid getting mixed up in the process.
  2. Perhaps you’ll need to remove your grommet pegs and then untie the remaining cable before you can continue.
  3. 2.
  4. Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
  5. Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
  6. If you are unable to use your previous cord as a reference, measure and mark the new cord to be approximately 8 inches shorter than the pole, or around 75% of its overall length.
  7. You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.
See also:  Where To Tent Camp In Yellowstone

Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.

Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.

Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.

When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.

When you’ve reached the desired length with the string, tie a knot here to ensure that the peg is secure.

Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.

All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable inside a tent pole.

All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.

The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.

If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.

How to Repair a Shock Cord if it Breaks in the Field

A snapped or overstretched shock cable might make erecting your shelter more difficult if you’re already out on the trail during your camping vacation. If you want to repair the wire without having to replace the entire length, fortunately, there is a simple solution. However, while this is not a permanent solution, it will allow you to use your tent for a short period of time until you can replace the cord completely. If the cable hasn’t snapped, but rather has become too stretched out to go around your tent pole, there’s a simple solution.

  • Then, draw the shock cable through the grommet peg until it is taught once again, and reattach it to the grommet peg.
  • If the shock cord on your old tent pole has snapped, you’ll need to remove the pole using the steps outlined above to fix the problem.
  • Remove a few inches of the cord’s elastic core on each side of the break, leaving only the braided sheath on the other side.
  • The reason you need a thinner segment of cord to tie the knot is so that the knot will not become trapped in the poles and will be able to flow through freely.

Using string as a temporary replacement for a broken shock cord

If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can purchase a new replacement cable. Although this will not have the same elastic characteristics as real shock cable, it can be used as a temporary replacement until you can make more serious repairs. Keep this in mind when using this. All you need to execute this DIY patch is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a small number of supplies.

  • Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
  • Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
  • This will make it much easier to thread the string back through the tent.
  • Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
  • Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
  • Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.

When you’re finished, we recommend that you unfurl your poles to make sure there’s enough slack to pack away your tent properly. Any mistakes can be corrected by untying the end at a peg and making any required modifications.

How to repair a broken tent pole

The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a damaged tent pole as well as changing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.

  1. Purchasing a repair sleeve is a cheap option if your tent does not come equipped with one; you never know when you might require one.
  2. If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
  3. If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
  4. Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.
  5. Using duct tape, secure a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did previously.

Preventing damage to your tent poles in the future

If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.

When building your tent and connecting the tent poles, start with the central segment and work your way out from there.

This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.

You’ll be considerably more likely to prevent repairs and replacements in the future if you follow these few simple suggestions. If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.

Final Verdict:

It is occasionally required to replace the shock cord in your tent pole, but it does not have to be a difficult process. It is possible to save a large amount of money by making minor repairs and replacements to your camping equipment over time, and it is also considerably healthier for the environment. Learning how to execute these little repairs is simple, and more importantly, it will make you a more experienced camper. As an added bonus, watch this video for some further tent pole repair advice!

How do I repair the shock cord at the center of my pole?

This page was last modified on Tuesday, March 9, 2021 at 10:26 a.m. If you have a shock cord that has become stretched out, gone slack, snapped, or is just worn out and in need of replacement, you have come to the proper spot to get it replaced. This is really a fix that can be completed rather fast and simply at home with little tools. Quest Outfitters carries shock cord, which can be obtained at most hardware stores, outdoor retailers such as REI and Moosejaw, and sporting goods stores.

DIY Shock Cord Replacement

On Tuesday, March 9th, 2021, at 10:26 a.m., the document was modified. If you have a shock cord that has become stretched out, gone limp, snapped, or is just worn out and in need of replacement, you have come to the perfect spot to get it replaced! The truth is that this is a really simple and quick repair that can be completed at your own convenience. In addition to most hardware stores and outdoor retailers like REI and Moosejaw, shock cord may be bought at Quest Outfitters and other outdoor retailers.

  1. The shock cord will be wound in a knot once the end tip has been removed (either on a washer or on the end tip of the pole). Cut the knot and you’ll be able to remove the shock cord with ease. The most essential thing to remember is to remove the pieces of each pole in the same sequence that you removed them. After you have removed the old shock wire, you will be ready to thread the new shock cable on each pole. Remember to string them back together in the same sequence. Gently push the shock cord through the entire length of the pole, then tie it off at one end (either with a simple knot or with a loop attached to the pole tip)
  2. Then, to tension the shock cord, pull out about 25% of the total length of the pole in slack (for a 10ft pole, pull out 2-3ft), and tie it off at the pole end. After that, you may check the tension and make any required adjustments
  3. The pole parts should softly seat themselves. Keep in mind that this is not an exact science, so use your best judgment and common sense while making decisions. Remove any extra shock cable after that, and you’re finished

Here’s a link to a fantastic tutorial from REI that goes over the process of fixing tent poles and includes a part on how to restring shock cord at the base of the pole: Fixing a Tent Pole (with Pictures) Did you find it to be of assistance? Yes NoFeedback is not required.

How to replace shock cord in tent poles

Have you ever experienced that shaky, jittery feeling in your stomach? I’m talking about the one when your tent poles don’t instinctively want to snap together, but instead stand at attention like slender, lightweight soldiers on display. Even if you’ve owned your tent for a long time and taken it on a number of trips, sooner or later you’ll need to learn how to replace shock cord in tent poles. Here is a video tutorial showing you how to do it step by step. The good news is that changing the shock cable in your tent poles is not difficult to accomplish.

See also:  How To Get Bugs Out Of Tent

Listed below is the procedure I used to replace the shock cable in my Macpac Sololighttent.

You will need:

  • Repair or replacement shock cord (check with your local hardware store, maritime store, eBay/Amazon, or tent maker for options)
  • Scissors
  • Sticky tape (gaffer tape, masking tape, duct tape)
  • Sharpie

In addition to losing its stretch, this ancient shock cable featured substantial regions of damage where the cord looked to have been welded to itself, which was discovered upon investigation.

Step 1: Remove the old shock cord

The method for gaining access to and removing the cable varies depending on the type of tent. Each end of mine has a straightforward screw top fitting. As an alternative, you may just cut the cord and slip it out from below.

Step 2: Keep the poles in order and number them

Those clever people who design our tents may have specified a certain order in which the poles must be installed in order to guarantee that the tent maintains its proper shape.

Consequently, number your poles so that you can quickly put them back together again. much as you would while cheating on a crossword problem.

Step 3: Tie a knot in one end and secure

Taking note of how the maker fastened the final knot may be beneficial so that you may replicate it later. Remove any surplus material from underneath the knot.

Step 4: Start feeding through your cord

Make your way around to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through until you reach the lug and secure it in place.

Step 5: Continue threading poles in order

Move to the other end of the cable and begin slowly feeding it through the number 1 tent pole, drawing it all the way through to the lug and fastening it securely in place with your fingers.

Step 6: Apply tension and hold in place

As you near the end of the rope, you will need to apply some stress to the elastic shock cord in order for it to make it all the way to the other side. While threading the final pole, you’ll need to secure it with some tape to keep it from moving about.

Step 7: Test the tension

Test the tension in your tent poles by bending them into the approximate form of your tent frame before tying everything off at the end.

Step 8: Tie a knot in the end and secure

Secure the end lug with a knot at the end of your cording project. Insert the knot and lug into the end of the pole and tighten them together. Posted on September 13, 2019 in How To by admin

Amazon.com : tent pole shock cord

THE RESULTSPrice and other information may differ depending on the product size and color selected. Ships to NetherlandsThere are only 7 of these items left in stock – purchase soon. There is just 1 left in stock – order soon. Ships to the Netherlands Ships to the Netherlands are available. Only 17 of these items are left in stock – purchase soon. extremely well-liked sponsored | based on the number of customer ratings and the number of stars There is just 1 left in stock – order soon. Ships to the Netherlands Ships to the Netherlands are available.

  • When you spend $300.00 or more on specified goods, you will save 8%.
  • Ships to the Netherlands are available.
  • Ships to the Netherlands are available.
  • Ships to the Netherlands are available.
  • Ships to NetherlandsThere are only 6 of these items left in stock – purchase soon.
  • Save up to 5 percent with this discount (on certain sizes and colors).
  • At checkout, a ten percent discount is applied.

GOLBERG Elastic Shock Cord – 2.5mm, 1/32, 1/16, 3/16, 5/16, 1/8, 3/8, 5/8, 1/4, 1/2 inch diameter – Various Colors – 10, 25, 50, 100 ft lengths – Made in the USA (Neon Orange, 3/16in x 25ft)

Ships to the Netherlands are available. Only 6 of these items are left in stock – purchase soon. Ships to the Netherlands are available. There is just one left in stock, so act quickly. Ships to the Netherlands are available. There are only 3 left in stock, so place your purchase now. Ships to the Netherlands are available. Order quickly as there are only 5 left in stock. Brands that are associated with your search

How To: Replacing the cord in your tent poles

17th of July, 2020 Tension is applied to tent poles by the use of shock cock, an elastic string that aids in the snapping back together and maintaining the form of the tent poles. It is possible for the elastic in the shock cord to degrade with time, causing the cord to sag and, eventually, making your poles very difficult to use and practically impossible to use. A replacement tent pole set may be rather expensive, so if your poles are still in good condition, it is significantly more cost effective to simply change the cable.

Because these tent poles are from my Sierra Lightning II FL, and because no two tents are exactly alike in terms of size, the quantity of shock cord you’ll need may vary depending on your tent.

When determining the quantity of cord to purchase, I find it better to just purchase the same amount as your pole dimensions to allow for some margin of error.

You will, however, be tensioning the cord at a length that is approximately two sections less than the actual length of your poles when you tension it. Shock cord is available at most respectable camping stores as well as on the internet.

What you’ll need:

  • July 17, 2020 is the day on which the event will take place. When the tent poles are stretched, they snap back together and maintain their form. Shock cock is used to hold them in place. It is possible for the elastic in the shock cord to degrade with time, causing it to droop. Eventually, this will cause your poles to become extremely difficult to use and practically impossible to use altogether. Replacement tent pole sets may be expensive, so if your poles are in good condition, it is significantly more cost effective to change the cable instead. Before we get started, there are a couple of things to consider. First and foremost, the tent poles are from my Sierra Lightning II FL, and unless you have the exact same tent as I have, the quantity of shock cable you’ll use may vary depending on your setup. In my tent, each pole is joined by a swivel, and the entire structure is made of canvas. In order to allow for error when estimating the quantity of cable to use, I recommend purchasing the same amount as the pole dimensions. You will, however, be tensioning the cord at a length that is approximately two sections less than the actual length of the poles when you tension the cable. Shock cord is available at most reputable camping stores as well as on the internet for a little cost.

This is applicable to poles that have a stopper that is inverted in the ferrule rather than a pull or screw-out type stopper. You may also watch a video on YouTube that shows you how to replace the cable on your tent pole. Tent poles are being unfolded.

Step 1

Prepare your tent poles by laying them out. Because you’ll be unthreading them, you’ll want to do this in a place where you have lots of space to keep them organized.

Step 2

The end stop at the end of your tent pole should be removed. Removal of the end stopper* If your tent poles are the older design with a stopper or washer in the ferrule, you’ll need to take the knot out of the stopper with tweezers and cut or untie it to allow the new rope to pass through and out of the way. When you reach to the other end, you’ll have to repeat the process in the opposite direction. The difference between poles with a pull-out end stopper and poles with a washer is seen in the diagram to the right.

Step 3

Untie the string or cut it at the end stop and set the end stop on the ground. As you begin to remove the old shock cord, make sure to arrange your tent poles in the same position as you did previously. Taking the cable out

Step 4

Obtain your new piece of shock cable at this time. I’ve pre-measured my and indicated the place where I want it tensioned to, but I’m not going to cut it yet since I find it simpler to tie and cut it once it’s already been tied. Begin with the first piece of pole and pull your shock cord all the way through to the stop at the end. Then tie a knot around the end stop to keep it in place. INVERTED STOPPER: If you’re working with an inverted stopper, you’ll want to make sure your wire is prepared.

When you reach to the end, tie a strong knot large enough to prevent the shock cord from passing through the hole again.

Feeding the wire through the washer is a simple process.

Step 5

Now that the end has been attached, draw the shock cord through the remaining sections of poles, being sure to retain them in the same sequence as they were originally put out.

Step 6

To finish, draw your shock cord through all of the remaining sections of poles, being sure to preserve them in the order that they were originally put up.

Step 7

When you’re satisfied with the tension, cut the cord neatly and tuck the end back inside the pole sleeve with the end stop, securing the end stop with a screwdriver. The shock cord may require assistance in this area since it is difficult to cut and is much simpler to cut when someone else is tensioning it for you.

How to Fix your Pole Set

When you’re satisfied with the tension, cut the rope neatly and tuck the end back inside the pole sleeve with the end stop, securing the end stop with a safety pin.

The shock cord may require assistance in this area since it is difficult to cut and is much simpler to cut when someone else is tensioning it for your benefit.

  1. Locate the pole splint and the broken pole segment in your pole set by following the arrows. The pole splint should be pushed up the poles until it is covering the fractured pole piece. Make use of duct tape or repair tape to keep the pole splint firmly attached to the pole set. You can use a pole set until you’re able to return home and do a more thorough repair. Watch this video for a brief instruction on how to use it.

At-Home Repair

Once you have returned home, please contact our customer service department. Because pole segments are removable, you won’t have to replace the entire pole set if one segment breaks. If you have any questions, please contact us at 800-997-9301, or fill out our Spare Parts Obtain Form to request a pole section. In either case, they’ll be pleased to assist you in restoring your pole set to full functionality in preparation for your next expedition. Although disassembling a pole set might seem scary if you’ve never done it before, it should be a simple and quick operation as long as you follow the steps in the instructions carefully and thoroughly.

See also:  What Size Led Light Do I Need For My Grow Tent

This chart may also be used to keep track of your progress once you have received the replacement pole section and are ready to begin the repair.

Once you’ve received the new pole segment, follow the step-by-step process below for replacing it in your pole set:

1. Remove the ball cap from the end of the pole that is closest to the damaged segment. After that, detach the ball cap from the shock cable with a screwdriver. Remove the ball cap from the pole by unscrewing it and pulling it away from the shock cord. 2: Untie the shock cord loop so that the shock cord may be readily threaded through the poles. One of the most common NEMO tent components, this three-pronged hub links the shock cable to the hub through a little black clip that can be taken out of the middle of the hub.

  • 3.
  • You may put a number on a piece of paper (or directly on the pole itself in marker) and name the poles as they come off the shock cord with that number as they come off the cable.
  • 4.
  • 5.
  • 6.
  • 7.

Special Instructions: Hubs

For damaged pole segments that need the removal of the shock cord from a central hub, this is the most effective procedure for restoring the hub to working condition. One of the most common NEMO tent components, this three-pronged hub links the shock cable to the hub through a little black clip that can be taken out of the middle of the hub.

Three-pronged hub: The Dagger, Aurora, Hornet, Hornet Elite, Firefly, and Dragonfly are all equipped with this hub, as are the Hornet and Aurora. One portion, the ridge pole of the tent, is joined to the other half by a little black clip, which is used to tie the shock cord to the hub of the tent.

The easiest way to remove this black clip is to:

1. To reach the shock cord of your pole set, use a sharp blade to go under the lip of the black hub covering and through the opening. It should easily pop out of the hub; we recommend removing both sides at the same time. With care, insert a blade between a lip on the hub covering and raise to release the cover. 2. Carefully pull the shock cable away from the black clip, allowing it to completely detach from the hub. This will assist in loosening the clip just enough to allow it to be removed.

  1. In order to remove this clip, we recommend pushing it out via one side of the center hub aperture with a pen; do not hesitate to apply pressure because the clip is quite tough.
  2. After that, you should be able to work it out far enough to be able to grip the other end with your fingers.
  3. After you’ve finished repairing your pole set, thread a loop of shock wire through the hub leg until it pokes out of the centre of the hub.
  4. 6.
  5. 7.
  6. To make a loop, feed the shock cable through the hub, then attach the black clip to the shock cord and pull the clip back into position in the hub to complete the loop.

Loose Shock cord? No problem!

Over time, shock cord’s elasticity might deteriorate as a result of its use. In the event that you observe fraying, loss of elasticity, or that the poles do not fit together correctly, it is critical that you replace the shock cord in your pole set. Shock cord may be found at most sporting goods stores and on the internet. You can also get in touch with us personally if you require shock cords. Following the installation of your new shock cable, you’ll want to disassemble your pole set according to the instructions provided above.

Do you have a question?

Quick Answer: How To Fix The Elasticity In The Tent Poles

Regarding a gear concern, the “string” that runs through the tent poles The shock cable may be removed and thrown away with less effort and weighs less. It is completely ineffective.

How tight should tent pole shock cord be?

Draw the thread through a basic binding knot about 2 inches from the end and tighten it. Your peg should now be in the middle of the knot and the long end of the rope, as seen below.

What’s another word for tent?

Ceiling, cover and roof are all terms that refer to a tentawning or a canopy.

Can you buy tent poles at Walmart?

Tent poles may be found at Walmart.com.

What is a tent pole moment?

There are three phases to mastering tentpole marketing opportunities.

Almost every company has a tentpole marketing moment – a time of year when the company’s reputation is at its highest point.

Can you fix a broken tent pole?

A pole repair sleeve is the quickest and most convenient method of repairing a damaged pole. This little tube, which is also known as a splint, is frequently included with your tent. If you don’t already have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not move about too much.

When should I replace my tent?

You may patch holes that are less than an inch in diameter, but if there are any holes that are larger than that, you will need to get a new tent. Check the seams for signs of straining, which is yet another indication that a tent purchase is on the horizon. When the poles are no longer able to tighten the cloth, you will not be able to keep dry in severe rain.

Do graphite rods break easily?

The fact that they are as robust as nails does not mean that they are readily broken. However, don’t tempt fate by being disorganized when it comes to arranging your fishing rods.

How do you cut a Fibreglass pole?

Align the rear edge of the fine-toothed hacksaw blade with the pencil mark using a straightedge and a level. Allowing the hacksaw to slowly move toward you and then away from you will allow you to cut through the fiberglass stick. Cutting should be continued until the fiberglass stick is divided into two halves. To finish the cutting operation, remove the masking tape off the fiberglass stick and discard it.

What can you use for tent poles?

In this article, we will cover everything from aluminum to fiberglass tent poles, as well as anything else in between. What is the best material to use in the construction of tent poles? Tent poles made of aluminum. Tent poles made of fiberglass. Tent poles made of steel. Tent poles made of carbon fiber. Tent poles made of composite materials. Air Beams are a type of beam of air.

Can you buy the top half of a fishing pole?

In most cases, getting a new rod will be more cost effective than repairing an old one, unless you have a heritage rod or need to have the rod butt fixed. There are a plethora of various types of “2 part fishing rods” available. It is preferable to get a new rod that is suitable for your planned application. I hope this has been of assistance.

Why do my tent poles keep breaking?

Strong winds, poles that have been weakened with age, and inexpensive materials are all potential causes—and occasionally it’s just plain old wear and tear.

Can I cut a fiberglass tent pole?

What is the best method for cutting fiberglass tent poles? Without a doubt, a basic hacksaw. If you don’t already have one, you’ll soon realize that you’ll need one. Masking tape a few loops around the area you wish to cut, then do it outside. It will take around three minutes total.

What does tent pole mean?

As used in broadcast and motion picture programming and films, the term “tent-pole” refers to a program or film that is important to the financial success of a film studio or a television network. It is intended to be an analogue for the way a strong center pole offers a secure framework to a tent construction.

How do you measure the diameter of a tent pole?

A vernier calliper can be used to determine the diameter required, or a tape measure can be used if one does not have access to one.

Take a part of your pole and place it end down on a tape measure or a ruler on a table. Then take another section of your pole and repeat the process with the tape measure. Now, have a look at the diameter.

What do you do with a broken tent?

Continue to: Repurposing Is the Most Effective Option. Recycle your tent by purchasing it from an online retailer. At a yard sale or garage sale, you may recycle your tent. Make Use Of A Local Recycling Center To Dispose Of Your Tent. Thrift stores are excellent places to recycle your tent. Don’t throw your tent in the trash or recycle it. Make Use of Your Old Tent for Indoor Recreation.

How do you remove tent pole end caps?

Mine are just minimally screwed on with the stress created by the cable within the earbuds. They simply twist themselves off. There should be a little tooth that just barely fits into a groove to complete the look. It is necessary to use a large adjustable wrench, which I move around the pole and then use to pound the end off.

How do you remove a ferrule from a tent pole?

Place the pole in a vice and heat the ferrule’s tip with a heat gun, grabbing the ferrule with pliers as it heats up, and turning it to check if it starts to move. It is important not to overheat the pole, since this will cause it to burn.

What is a tent pole issue?

: a high-budget film whose revenues are projected to more than offset the losses suffered by the studio on its other films.

Does REI repair tents?

If you have any doubts about your abilities to repair a tent pole, REI shops can do basic repairs.

Can you repair fiberglass tent pole?

The Coghlan’s Fiberglass Tent Pole Repair Kit, which includes four 9.5mm fiberglass tent pole sections as well as shock cord, lead wire, and ferrules, allows you to repair broken or damaged tent poles in a matter of minutes. This kit might save you the money you would have spent on a brand new tent, plus it is simple to assemble and operate.

What is a tent ferrule?

When two composite rods or tubes are joined together, ferrules are utilized to link them together. They also make it possible to employ shorter carbon or fiberglass rods or tubes, as well as to construct and dismantle your finished product, resulting in a smaller container for transportation purposes.

What are flexible tent poles made from?

When two composite rods or tubes are joined together, ferrules are utilized to make the connection. They also make it possible to employ shorter carbon or fiberglass rods or tubes, as well as to construct and dismantle your finished product, resulting in a smaller container for transportation.

Can I buy replacement poles for my tent?

When you have a Coleman Replacement Tent Pole Kit as part of your camping equipment, you may save money by purchasing a new pole rather than a new tent. It comes with four 27-inch fiberglass replacement poles that connect to one another, allowing you to customize the length of the new pole to your specifications. The package also includes a 10-foot extension cord.

Do they sell tent poles?

REDCAMP Aluminum Tarp Poles Heavy Duty and Adjustable, Set of 2, 35″-90″/75″-86″ Telescoping Lightweight Tent Poles for Tarp Canopy Awning Shelter, 35″-90″/75″-86″ Telescoping Lightweight Tent Poles for Tarp Canopy Awning Shelter, 35″-90″/75″-86″ Telescoping Lightweight Tent Poles for Tarp Canopy Awning Shelter,

Leave a Comment

Your email address will not be published. Required fields are marked *