How To Fix A Broken Fiberglass Tent Pole

How to Fix a Broken Tent Pole

There have been 58 reviews with an average rating of 3.7 stars out of 5 stars for this product. Tightly woven tent poles serve as the skeleton of your outdoor shelter, giving support and structure to keep the tent standing. If a pole breaks, your tent may wobble, flap, or fully collapse, therefore it’s a good idea to be prepared with the essential materials and know-how to repair a broken pole before you go camping. In this tutorial, we’ll show you how to do the following:

  • While in the field, learn how to use a repair sleeve or an old tent stake to hold a broken tent pole together until it can be repaired at home. Learn how to replace the flexible shockcord inside your tent pole if it breaks or wears out and how to make an at-home repair.

Repairs by professionals: If you require expert assistance, many REI locations can do simple repairs. Alternatively, TentPole Technologies, the nation’s best pole repair service, is a fantastic alternative. REI Repair Services is a division of REI.

Splinting a Broken Tent Pole

The damage done to your tent pole by a violent gust of wind or stepping on it is irreversible. A kinked, split, or shattered pole requires rapid treatment when out camping (when you get home, you can look into having the pole replaced or professionally repaired.) There are two alternatives available to you:

  • Use a pole repair sleeve to fix the problem. Make a splint out of a tent stake.

Using a Pole Repair Sleeve

A pole repair sleeve is the quickest and most convenient method of repairing a damaged pole. This little tube, which is also known as a splint, is frequently included with your tent. If you don’t already have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not move about too much. A repair sleeve is an easy way to patch a broken tent pole. Here’s how:

  1. Stack the broken pole components in a straight line
  2. It is possible to straighten out the curvature in the pole if it is bent but not completely broken. Adjusting the sleeve over the pole end until it’s perfectly centered over the break or kink can necessitate the use of pliers or a rock to bend spread sections so that the sleeve can glide over them
  3. Make two or three wraps around each end of the sleeve/pole, using duct tape or whatever heavy-duty tape you happen to have on hand. It may be necessary to splint the portions of a broken pole together where one pole end fits into the next pole end
  4. However, this will prevent the poles from folding neatly when you pull the tent down.

Using a Tent Stake as a Splint

If you’ve misplaced or forgotten your pole repair sleeve, you may make a rudimentary splint out of a tent stake as follows:

  1. Stack the broken pole components in a straight line
  2. The curve should be straightened out if the pole is bent but not completely broken. Align the stake such that it is centered close to the breach in the ground
  3. Wrap duct tape around each end of the stake/pole many times, or use whatever heavy-duty tape you have on hand.

How to Replace Tent-Pole Shockcord

After a period of time, the flexible shockcord that is included within your tent poles may become abraded and snap, or it may just lose its elasticity completely. Despite the fact that the shockcord snaps while you’re out in the field, you may still utilize the pole by carefully assembling each of its component pieces. But when you arrive home, you’ll want to replace the shockcord since it simplifies the assembly process and prevents you from losing a pole segment during transport. Fortunately, the procedure of changing it is uncomplicated.

  • A permanent marker
  • Masking tape (optional)
  • Scissors
  • Locking pliers (optional)
  • A new 1/8-inch-diameter shockcord (about the length of your tent pole)
  • A permanent marker
  • Locking pliers (optional).

The following is the procedure for replacing the shockcord:

  1. Begin by placing the tent pole out straight on the ground. Sections can be labeled with a permanent marker (masking tape can be used if you don’t want to write directly on the pole) to prevent them from becoming mixed up. Remove the old cable by snipping it, and then take the elastic out of the pole end. Maintain the same sequence and alignment of all of the pole parts for the duration of your job
  2. It is common for tent poles to have a little metal piece attached at either end where the string is fastened
  3. Keep an eye out for these pieces and make sure they are not lost. Using your old shockcord, untangle the ends and place them next to your new shockcord. the length of the new piece of shockcord should be trimmed to match the length of the original The replacement part should be approximately 8 inches shorter than the previous section if the old shockcord has become stretched out and no longer has its elastic properties. Tighten one end of the shockcord and pass the other end through all of the pole sections until the last one
  4. Make a temporary knot in the shockcord to prevent it from slipping back into the second-to-last pole piece
  5. Alternatively, you may use a pair of locking pliers to secure the cord in place. Feed the remaining shockcord through the final part of the pole and tie the end together. Return to the beginning and untie (or unclamp) the rope that connects the final two pole parts. Check to make sure that all of the pole components are securely fastened to the completely completed pole. If the shockcord is still too slack, untie one end and pull it out 6 inches at a time until the poles are securely fastened together when the shockcord is tightened. It is important not to over-shorten the rope. Using pliers, remove the parts of the pole and fold it up starting at the center position

Related Articles

  • Getting Started with Tent Care
  • How to Repair a Tent
  • Checklist for Backpacking Repair Kits
  • How to Set Up a Tent

Contributing Experts

Jon Almquist works as a product manager for tents at the REI Co-op headquarters in Kent, Washington.

Laura Evenson

Currently, Laura Evenson works as a sales lead in the camp and climb departments at the REI Conshohocken location in Pennsylvania. Laura’s 2013 Appalachian Trail thru-hike included 27 consecutive days of rain, demonstrating her tenacity as an adventurer.

Chris Pottinger

Chris Pottinger works at REI Co-op in Kent, Washington, as a senior tent designer.

Lindsey Stone

Currently based in Seattle, Lindsey Stone works as the operations director for Rainy Pass Repair Inc. Prior to that, she worked as a professional sewing technician for a total of 12 years. Her family, which includes her husband, kid, and dog, likes hiking, camping, and canoeing together.

How To Repair Broken Fiberglass Tent Pole

Do you have a tent at home with a damaged fiberglass pole? If so, let us know. Did your tent pole break while you were camping? What is the best way to repair split fiberglass tent poles? The likelihood of your camping equipment becoming damaged increases dramatically when you camp on a frequent basis. Accidents happen all the time, and your poles may become damaged as a result.

This might be really unpleasant since you will be unable to utilize your tent and enjoy the outdoors as a result. In this regard, I will provide you with some practical tips on how to repair a fiberglass tent pole so that you can get back to camping in no time.

Fix a broken fiberglass tent pole like an expert

You may already have a tent at home that has a damaged fiberglass pole. Were you at the campsite when your tent pole broke? In this article, we’ll show you how to fix a split fiberglass tent pole. The likelihood of your camping equipment becoming damaged increases significantly when you camp frequently. Accidents happen all of the time, and your poles may become damaged as a result of one of them. As a result, you will be unable to utilize your tent or enjoy the outdoors, which may be really annoying.

I hope this helps.

Fiberglass tent pole kit

Among the items you will require for this project are: replacement tent poles, a tiny hacksaw, and a screwdriver. SandpaperØ A face mask made of duct tape

The process

The fiberglass poles that are used to support tents are often constructed from a number of loose pole parts that are kept together by a flexible cable or rope. The elastic cable, also known as a shock cord, is threaded through the length of the poles and knotted at both ends to keep it in place. In the event that your pole breaks, it is most probable that just one of the portions has been broken off. You will need to replace it if you want to restore the tent to its original state of operation.

  1. Measure the precise portion of the tent pole that has to be replaced and mark it on the tent pole.
  2. Cutting the fiberglass pole with a hacksaw will require you to put on a face mask, which you should do before starting.
  3. Use duct tape to hold the new pole in place while you cut it to the proper length.
  4. The creation of splinters will be prevented as a result of your ability to cut in an ordered manner.
  • Eliminate any remaining pieces of Duct Tape from the pole and sand the pole’s edges to create an even surface. Place the entire tent pole on the floor and begin untying the knot at the end of the pole that is closest to the portion that will be replaced. It is doubtful that you will be able to reach the end of the knot with your fingers, thus a needle nose plier should be used to free it from the pole. It’s possible that the knot was knotted too tightly and you’ll have to cut it
  • Holding the shock cord in place, gently remove the pole parts until you reach the broken part that has to be repaired or replaced. Removing the damaged portion and replacing it with the section that you have prepared is a good idea. While maintaining your grip on the shock cord, re-stretch it through the pole portions that you had previously removed for the time being. Due to the fact that the sections are of varying lengths and diameters, it is important to return the poles in the same condition as you found them. It is possible that your tent will not stand up properly if you mix them together. Finish the string by tying a knot at the end and making sure that it is taught in the same way that you discovered it. The cable secures the tent’s poles in place and provides a defined framework for the tent. This is why you should make certain that it is taught in sufficient quantities.

Remove the duct tape from the pole and sand the pole’s edges to create a flat surface. Start by laying the tent’s whole pole on the floor and untying the knot at the end of the pole that is closest to the piece that needs to be repaired. It is doubtful that you will be able to reach the end of the knot with your fingers, thus a needle nose plier should be used to pull it off the pole. It is possible that the knot was tied too tightly, and you will need to cut it; Holding the shock cord in place, gently remove the pole parts until you reach the broken item that has to be repaired or replaced To repair or replace a broken portion, remove it and replace it with the section that you prepared; While maintaining your grip on the shock cord, re-stretch it through the pole parts that you had previously removed for safety reasons.

Because the parts are of varied lengths and diameters, it is important to return the poles in the same condition as you found them.

Finish the string by tying a knot at the end and ensuring that it is taught in the same manner as you discovered it.

The cable secures the tent’s poles in place and provides a defined framework for the tent’s inside. Because of this, you should make certain that sufficient instruction is provided.

Use a tent pole repair sleeve

Another option for resolving the issue is to use a pole repair sleeve to secure the pole. A short pole or a so-called splint, which is typically included with the tent that you purchase, is used to repair the tent in the shortest amount of time possible. You should get it even if it is not included in the bundle to be prepared for the worst case scenario. So, what is the best way to fix a tent pole with a splint? To begin, arrange the two broken pole portions in a straight line. If the pole is not broken, simply bend it in half and gently straighten it out.

Straightening the bent parts using pliers can be done with the assistance of a friend.

Use a tent stake

There is another solution if you don’t happen to have an emergency repair kit or a pole repair sleeve with you. If your pole breaks, you can use a stake to put the two fractured sections of the pole back together again. To begin, arrange the broken pole components in a straight line. If each is bent straight, it may be manipulated using pliers. Assemble the stake and place it next to the shattered section; the stake must be centered between the two fractured components. The next step is to use duct tape or another type of heavy-duty tape to secure all of the pieces in place before proceeding.

How do you replace a shock cord?

Is your shock cable in the poles damaged or no longer stretches when you pull on it? In these instances, it is past time to replace it.

Step1

First and foremost, you must understand how the shock cord is linked. To see the cable, open the end of the pole and pull it out. In most situations, a metal or plastic tab will be located on the pole, which you may pull out and repair the cable with.

Step2

Mark the pole parts with numbers so that you will know how to link them together at the conclusion of the project. Remove the old shock cord by untying it, pulling it out, and placing it somewhere where you can cut a new cord of the same length.

Step3

Take the new cord and connect a tab to the end of it using a piece of tape. You’re almost through with threading the cable through the pole. Using the clamp or vise grip, forcefully pull the cable to cut it off when you reach the end of the final pole segment you are threading.

Step4

Finalize the procedure by connecting the core to the pole’s tip and knot the remaining end of the pole.

Save the money

Tent poles break all of the time, but this does not imply that you must discard your tent and purchase a new one in order to fix the problem. A damaged pole can be repaired by the homeowner. You will be able to fix a damaged fiberglass tent pole without much difficulty if you follow my recommendations.

About The Author

Camping Valley was started by myself. I am the company’s founder. The site is an extension of my outdoor lifestyle and appreciation for the great outdoors that I have.

Everything that I learn, experience, and consider worthwhile is available to you on this website. We live in a technologically advanced age, yet nature is always telling us that we should spend time in areas where our hearts and souls feel at home.

Amazon.com : Coghlan’s Fiberglass Tent Pole Repair Kit : Sports & Outdoors

a rating of 2.0 out of 5 stars They’re priced so low for a purpose. On August 10, 2019, a review was conducted in the United States. I bought tent poles of the same diameter as my previous ones, but the ones that arrived were somewhat smaller in diameter, resulting in a gap between the old pole and the new pole when I linked the two together. I was able to utilize metallic plumbers tape to make the smaller pole more tight and fit appropriately by wrapping it in the tape. The threading wire is completely ineffective; instead, simply take out as much of the shock cord as you can and then use a clamp to hold it taught, and you will be able to thread through with no issue.

See also:  What To Bring For Tent Camping

These are inexpensive because they are inexpensive.

Top reviews from the United States

Verified PurchaseReviewed in the United States on August 10, 2019Verified Purchase I bought tent poles of the same diameter as my previous ones, but the ones that arrived were somewhat smaller in diameter, resulting in a gap between the old pole and the new pole when I linked the two together. I was able to utilize metallic plumbers tape to make the smaller pole more tight and fit appropriately by wrapping it in the tape. The threading wire is completely ineffective; instead, simply take out as much of the shock cord as you can and then use a clamp to hold it taught, and you will be able to thread through with no issue.

  • These are inexpensive because they are inexpensive.
  • a rating of 2.0 out of 5 stars They’re priced so low for a purpose.
  • I bought tent poles of the same diameter as my previous ones, but the ones that arrived were somewhat smaller in diameter, resulting in a gap between the old pole and the new pole when I linked the two together.
  • The threading wire is completely ineffective; instead, simply take out as much of the shock cord as you can and then use a clamp to hold it taught, and you will be able to thread through with no issue.
  • These are inexpensive because they are inexpensive.
  • The photographs in this review On December 24, 2020, the United States will conduct a review.
  • Just make sure you don’t inhale any dust.

To get the cable into the hole, I had to use a flashlight, which I clenched between my teeth (a headlamp would have been a better idea).

Because the provided wire is fairly thick, you won’t be able to perform the usual thing and attach the end of the cord to the wire; instead, you’ll have to just stuff the wire through with the cord to complete the installation.

In addition, the cable is visible.

A thicker material will not bend as readily, but it will last longer; a blind is often kept in one place for weeks or months at a time, and the weight of rain or snow might cause the rods to break, so a durable material is recommended.

Useless.

Use caution with a hacksaw, as previously suggested, and you should have no problems with splitting or fibers becoming trapped in your fingers.

This is a dreadful situation.

I’m going to keep them and give them a light sanding and a coat of spray paint.

Unfortunately, one of the packets was missing a few parts, which was a shame.

Two stars because they are fiberglass and will work for ME, but they may not be as effective for you as they are for me.

Purchase that has been verified It took years for me to stop being cheap and mend a broken window pole in our cougar flats tent, but I was determined to do it.

Despite the fact that it had a greater diameter than the item it was replacing, it was still functional.

On August 23, 2019, a verified purchase was reviewed in the United States of America.

Make use of masking tape and a fine-tooth hacksaw to complete the project.

Disassembling the parts makes it simple to thread the elastic cord through the holes and tie a fresh knot.

This was a complete success.

However, I discovered that the extra fiberglass pole sections are abnormally lengthy.

Before purchase, be sure you measure the length of your tent pole sections.

Verified Purchase Although I cannot comment on how simple it was to install these poles because my husband performed all of the work, our tent pole is now functional again!

However, a little piece of electrical tape fixed the problem. On July 7, 2021, a review was published in the United States of America. There are no directions, but it is quite simple to figure out what to do. However, there should be some sort of set of instructions.

Top reviews from other countries

5.0 stars out of 5 for this product It worked perfectly for mending my Coleman tent poles. On June 24, 2020, a reviewer in Canada noted that the purchase had been verified. In order to repair three broken pole parts on my Coleman tent, I bought these. Although I anticipated they would be too long based on another reviewer’s description, I was able to cut a few inches off the end and then sand it down to perfection, and they functioned flawlessly. The most difficult element was probably getting the elastic chord re-strung through the older pieces of the current tent pole, which proved to be the most difficult.

  1. Very good value, excellent protection for my tent, and I’m confident that they will survive for many years.
  2. The varillas are made of glass fiber.
  3. Purchase that has been verified These varillas were purchased with the intention of replacing a rotted varilla from a toldo with mosquitoes that I had purchased in the United States.
  4. I didn’t have to use any elástico or varilla terminations; instead, I simply had to cut a 10 cm strip from the new varilla and cut away the elástico with some nail pins, then use a hilo and an aguja to reinstall the varillas.
  5. Purchased on September 29, 2019 in Canada and reviewed on September 30, 2019Verified Purchase “It’s a touch short,” the wife commented on the shortness.
  6. It is difficult to locate precise replacement entire poles.
  7. Purchase that has been verified I have a Coleman BP Bristol tent that I use for camping.

We were unable to locate replacement poles.

You need delete the previous part.

Then you manage to either re-insert the old shock cord or use a new shock cord to fix the problem.

You have rescued an entire tent for only a few dollars.

On October 26, 2021, a review will be conducted in Canada.

I believe the wire is intended to be used for threading the bungy through the rods, but simply threading it through the rods works just as well. Metal end caps may be used as tent poles, whilst plastic end caps are simply that.

How to Fix a Tent Pole

Documentation Download Documentation Download Documentation Breaking a tent pole might bring your camping vacation dreams crashing down around you, literally, if you’re not careful. That is, unless you know how to do a few simple repairs on your own. A few simple, readily-available supplies will have you back in the warmth and safety of your dependable shelter in minutes, whether you’re tape up a pole that’s been split down the middle, strengthening a broken part, or replacing a worn out shock wire.

  1. 1 Place the damaged pole on a level place and allow it to air dry. This may be accomplished with the use of a portable camping table or picnic table. You can also place the pole on top of a flat piece of equipment, such as a cooler or a toolbox, if you don’t have access to either of these pieces of furniture. The worst-case situation may be solved by placing a smooth rock or a level stretch of ground on the ground.
  • There is no need to disassemble the pole or remove the elastic shock wire that binds it together
  • This is a simple procedure. Clean up any leaves, twigs, pine needles, sand or other similar material from your work surface before you continue. It is possible that if any of these materials make their way onto your tape, they will impair its ability to adhere correctly.
  • 2 Cut a piece of gaffer’s tape the same length as the split part and place it over the split segment. To decide how long a strip of tape you will require, align the loose end of the tape with the extreme end of the segment, then gently unspool the roll until you reach the far end of the segment. Cleanly tear the tape to ensure that both ends are perfectly square
  • Gaffer’s tape is a sort of heavy-duty, high-strength tape that is widely used to repair electrical and mechanical components. It is also known as gaffer’s tape duct tape. You can pick up a roll of gaffer’s tape for a few dollars at any hardware shop or home improvement center
  • If you didn’t bring any gaffer’s tape with you, an ordinary roll of duct tape will enough
  • If you forgot to bring gaffer’s tape, an ordinary roll of duct tape would suffice
  • Tip: This simple, no-frills solution is best suited for emergency scenarios, such as when a pole splits on you while you’re already out in the woods. Advertisement
  • s3 Place the lateral edge of the tape over the split and press firmly into place. Cover the full length of the split with a strip of tape measuring 1 4–1 2inch (0.64–1.27 cm). Depending on the breadth of the roll you’re working with, you’ll have between 1 2 and 11 2 inches (1.3 and 3.8 cm) of reinforcement left over.
  • It is significantly more beneficial to tape a split longitudinally than than merely covering the ends of the split. The greater the amount of surface area on which the tape can attach, the more securely it will clamp the split together.
  • 4 Continue wrapping the tape around the divide until it is completely covered. Fold the tape with care to prevent leaving wrinkles or creases in the fabric. The pads of your fingers can be used to smooth down the strip once you’ve secured the entire strip in place. You are now free to continue erecting your tent without any further concerns.
  • By wrapping the tape in this manner, you will be able to overlap the split itself at least twice while simultaneously tying the remainder of its length. It should be fine to go for the rest of the season, if not longer, if you use the proper type of tape and wrap your pole tightly.
  1. 1 If required, trim or break off the jagged edges surrounding the break to prevent it from fraying. Remove any shards or splinters that are visible extending out beyond the shaft of the segment with wire cutters, or pry them loose with a pair of pliers if they are stuck in the shaft of the segment. This will ensure that the afflicted area has a consistent thickness and that the rough edges do not cause more harm.
  • It’s possible that you’ll have to manually bend aluminum poles back into shape in order for them to fit inside the tent pole repair sleeves that you’ll be utilizing. A large number of aluminum tent poles can be bent by hand, but if you are having trouble, you may try using an arbor press in the same way that you would bend tiny aluminum sheet pieces.
  • It’s possible that you’ll have to bend aluminum poles back into shape by hand in order for them to fit inside the tent pole repair sleeves that you’re going to use. The majority of aluminum tent poles can be bent by hand
  • But, if you are having trouble, you may try using an arbor press in the same manner you would bend tiny aluminum sheet pieces.
  • Most modern tents come with at least one repair sleeve, which allows you to do quick repairs in the field. These are often constructed of an ultra-strong aluminum alloy, which results in a splint that is both durable and lightweight. Alternatively, if you don’t have a repair sleeve available, a tent pole or a stout stick might be used as a substitute.
  • Tip: Although it is not required to disassemble the pole in order to slide the sleeve into position, it may be more convenient to do so. 3 Duct or gaffer’s tape can be used to secure the ends of the sleeve. Strips of 4–6 in (10–15 cm) wide tape should be torn off the pole and wound around the spots on the pole where they emerge from the sleeve’s outer borders. After you’ve applied the tape, you’ll be free to set up and pack your tent as you usually would, safe in the knowledge that the splint will function to stabilize the fracture.
  • Feel free to wrap the tape around the sleeve as many times as necessary to be absolutely ensure that it remains in place. You may even go all the way around the sleeve if you want to
  • Despite the fact that the usual tent pole repair sleeve is durable enough to withstand numerous camping seasons, it’s a good idea to locate a new pole as soon as possible after the incident occurs.
  1. First, look for an identically sized replacement section to use in place of the damaged pole. Some tent manufacturers include replacement parts with their products, such as poles and pole segments, in the initial packaging. It’s possible that your tent didn’t come with any replacement parts, in which case you’ll have to buy a new section from the original manufacturer. If you’re buying an old segment, make sure you measure it across the opening to ensure you’re obtaining one with the correct measurements.
  • You may also be able to locate a specific pole segment that meets your requirements on a website or via a merchant that specializes in old outdoor equipment. Replacement tent pole segments are often constructed considerably longer than conventional tent pole segments, allowing them to be readily trimmed to fit
  • However, replacement tent pole segments are not always made this way.
  • 2 Measure and mark the length of the new section to ensure that it is the same length as the previous one. Place the two segments side-by-side on a level surface with their bottom edges lined and their bottom edges aligned. Use a felt-tipped marker to draw a thin line on the shaft of the new section where the previous segment stops, and then cut along that line. This line will identify the location of the new section segment where you will be performing the necessary alterations
  • Alternatively, you can place a strip of contrasting masking or painter’s tape around the segment to indicate where you want to make your cut. If your poles are constructed of fiberglass, cutting through the tape rather than the exposed shaft may also assist to prevent cracking or splitting. Don’t worry about being too accurate here
  • The goal is to prevent cracking or splitting. Whatever the length of the new segment is relative to the length of the original section, it will perform perfectly.
  • 3 Using a hacksaw, cut the section to the desired length. Orient the pole piece such that the portion bearing the mark you just produced extends beyond the edge of your work surface when you place it at the edge of your work surface. Then, using smooth strokes and steady, moderate pressure, glide the teeth of your hacksaw back and forth over the line. Continue to saw until you reach the end of the segment
  • This will take some time.
  • The opposing end of the section should be held securely in place with your free hand to prevent it from sliding around unexpectedly while you’re attempting to concentrate on sawing. When using your hacksaw, proceed with caution. Despite the fact that they are not very hazardous instruments, an accident might still occur if you are not paying attention to what you are doing.
  • Advice: If you don’t already have one, a small portable hacksaw might be a very helpful addition to your camping kit. 4 Smooth down the rough edges on the cut end of the new section with a file or sandpaper. Following the trimming of the piece to the proper length, all that is needed is to smooth out the new opening with a metal file or a sheet of medium-grit sandpaper to make it seem smooth. A gentle polishing will prevent the elastic shock cord that holds the pole together from fraying once a fresh cut has been made.
  • It is advisable to use sandpaper with a grit that is anywhere between 80 and 120 while doing this activity.
  1. 1 Remove the old cord from the pole by cutting the anchor knots at either end of the pole. Remove the knot from the pole by inserting a pair of needle-nose pliers into the open end of the pole. Cut the rope slightly below the knot with a sharp knife or a pair of scissors, and then wriggle it out of the jointed pole segments with your fingers.
  • When you pull the cable out, be cautious not to lose any of the loose pole pieces that may have come away. Because they’re cylindrical, they’ll be more prone to rolling than other shapes. Due to the fact that you will be dismantling the pole in order to install the new shock cord, now is a good time to replace any pole segments that are showing signs of wear.
  • Tip: Use a felt-tipped marker to number the pole parts, starting with the end that was cut first. Putting them all back together in the proper arrangement will be a piece of cake later on. 2 A knot on one end of the replacement cord will serve as an anchor for the replacement cord. Simply choose a point 4–6 inches (10–15 cm) away from the end of the string and loop it into a basic double overhand knot to complete the look. After that, give the knot a couple of strong tugs to make sure it’s secure
  • A steel washer can be placed on the segment of the rope where you intend to tie your knot if you so choose to do so. The spherical washer will provide something for the rope to bite into and will enhance the longevity of the completed knot, as well as its appearance. Putting a knot on one end of the rope before you start working it through the various segments that make up the pole will prevent it from accidently coming out.
  • 3 Each of your pole segments should have a fresh cable threaded through it. Running the cord through each section one at a time and securing them all together is the quickest and most efficient method of accomplishing this. In most cases, when you purchase a replacement shock cable, it will come with an attachable wire pull-through mechanism, which will assist you in speeding up the procedure somewhat.
  • When pulling the cord through, it may be helpful to have an aide hold each piece for you while you concentrate on pushing the cord through.
  • 4 Remove one end of the cord and tie it off with the pole stretched out to its full length. Once you’ve completed the process of running the new cord through each section, lay the entire assembly down on the floor. Extend the cord to generate some tension, then twist up a second double overhand knot 4–6 inches (10–15 cm) from one end of the cord opposite the one you began with. That is all there is to it.
  • Remember to put a second washer onto the string before tying your final knot if you used one on the first side
  • Otherwise, the knot will not hold. It is important to remember that if your shock cords are connected with metal pull tips rather than anchor knots, you must replace them according to the manufacturer’s specifications.
See also:  How To Fold Up A Pop Up Bed Tent

Inquire about something There are 200 characters left. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

  • To obtain a new pole for your tent while it is still under warranty, get in touch with the manufacturer. Depending on the circumstances, they may even replace the entire tent for a minimal fee. It will be necessary to reshape steel tent poles by a qualified metal craftsman, albeit it may be more cost-effective in the long run to simply purchase a new set of poles. When looking for spare parts for popular tent models, online shopping resources such as eBay can be extremely beneficial.

Thank you for submitting a suggestion for consideration! Advertisement

Things You’ll Need

  • Gaffer’s tape or duct tape for tent pole repair
  • A tent pole repair sleeve Wire cutters or pliers (as an alternative)
  • Optional: a tent stake or a stout stick (for use as a makeshift splint)
  • Toolkit includes: replacement pole segment
  • Felt-tipped marker
  • Hacksaw
  • Metal file or medium-grit sandpaper
  • Contrast tape (optional)
  • And instructions.
  • Sharp knife or scissors, steel washer (optional), replacement shock cable (optional), hacksaw (optional), and other miscellaneous supplies. Alternatives include: a file or sandpaper. Optional: a felt-tipped marker

About This Article

Thank you to all writers for contributing to this page, which has been viewed 8,655 times so far.

Did this article help you?

Obviously, this isn’t the best news, but it doesn’t mean you have to cancel your camping trip just yet. Furthermore, you will not be required to purchase a new tent. Replacement tent poles and a little know-how are all you’ll need to restore your tent poles to like-new condition. Continue reading for a fast and simple advice on how to repair broken fiberglass tent poles.

  • A set of replacement fiberglass tent poles for use with a canopy. If you’re not sure what you’re looking for, go with universal tent poles. A little hacksaw, sandpaper, and duct tape are all needed.

In order to construct your pole, you will need to use numerous loose “pieces” and an elasticated cord (sometimes referred to as a shock cord). The shock cord is simply knotted at each end once it has been threaded through each component from one end to the other. Measure the length of the portion that will be replaced (the new section is generally extra-long, so you may need to cure the new pole down to suit). Making use of a tiny hacksaw, cut the new section (if necessary) to the length of the pole that will be replacing the old one.

Then carefully peel away the duct tape and sand the edges until they are smooth.

Retain hold of the shock cord and carefully remove the pieces one at a time (while maintaining them in the proper sequence) until you reach the section that needs to be repaired or replaced.

You may always shorten or lengthen the shock cord by fishing out the knot in one of the end poles as it becomes necessary.

DON’T FORGET TO CHECK OUT OUR FULL CAMPING EQUIPMENT RANGE.

Purchases of $100 or more at the Outside Shop, where you’ll discover gear for all of your outdoor excursions, will earn you $50 off your purchase. Sign up for Outside+ as soon as possible. 1. A damaged tent pole, duct tape, and a tent pole repair sleeve will be required (REI.com sells repair sleeves for 75 cents). 2. A damaged aluminum pole would likely crimp and break before it can be repaired. If required, break off metal shreds and flatten the ends until they are small enough to fit into the repair sleeve’s opening.

  1. The processes for repairing a vehicle are the same.
  2. To do a rapid repair at the stroke of midnight, slip the repair sleeve over the damaged pole part, making sure it is centered on the break.
  3. 5.
  4. You may just tape the repair sleeve in place and go back to sleep to accomplish a rapid, one-night repair in this manner.
  5. 8.
  6. Duct tape one damaged end of the repair tube so that it fits firmly into the sleeve and the tape extends all the way to the end of the repair tube’s overall length.
  7. Place the tube in the desired location and label the opposite end.

Wrap the opposite half of the broken end in the same manner as the first half.

10.

11.

If the tape is firmly wrapped around the object, you won’t have to use any extra tape wraps to keep it in place.

12.

When both damaged pieces are wrapped and snugly fitted to the repair tube, the pole arc bends equally and evenly without any pressure spots that might cause the pole to fold again in strong winds.

The significance of the information.

In the case of a basic repair tube without any supporting duct tape wraps, the pole bends unevenly, and the black pole portions are twisted over the sharp edge of the repair tube, creating an unsupportable weak spot. Jennifer Howe/howephoto.us provided the photographs.

Backpacker Newsletter

The Outside Shop, where you’ll discover equipment for all of your outdoor excursions, is offering a $50 discount on any qualified $100 purchase. Outside+ is available to you right now. The following items are required: 1. A damaged tent pole, duct tape, and a tent pole repair sleeve. 2. (REI.com sells repair sleeves for 75 cents). An aluminum pole that has crimped and cracked will typically be identified. If required, break off metal shreds and flatten the ends until they are small enough to fit into the repair sleeve.

  1. There is no difference in repair processes.
  2. This may be done in minutes at midnight.
  3. Take note of how the broken pole ends have been shaped and cleaned up to ensure that they will fit into the tube.
  4. You may just tape the repair sleeve in place and go back to sleep to complete a quick, one-night repair.
  5. 8.
  6. The tube should be positioned and the opposite end should be marked with a marker.
  7. Take note of how the two duct tape wraps go all the way to the ends of the repair tube.

Slide the repair tube over the piece of the pole that has been taped with duct tape.

In this case, the result is as follows.

In order to maximize packing efficiency, you can remove and adjust the repair tube at your leisure.

When both damaged pieces are wrapped and snugly fitted to the repair tube, the pole arc bends equally and evenly without any pressure spots that might cause the pole to fold again in strong wind conditions.

If you use a simple repair tube and don’t use duct tape wraps underneath, the pole bends unevenly and the black pole portions are twisted over the sharp edge of the repair tube, creating a weak spot.

How to Repair a Damaged Tent Quickly & Easily [Do-It-Yourself]

A nice tent is designed to keep you safe from the elements while you’re camping. Although our gear has remained in good condition over the years, the elements can occasionally take their toll, resulting in damage to our trusted tent that must be repaired. Ripped fabric, leaking seams, and broken tent poles are all routine repairs that can be completed by any ambitious do-it-yourselfer in a short amount of time and with little effort.

How to Repair Ripped Tent Fabric

Sharp pebbles, fallen branches, strong winds, or the heat from a nearby fire can stretch the fabric of your tent past its limitations, leading it to get damaged. A rip or tear as a result of this does not always imply that your tent is no longer usable. It is true that you are now more exposed to the elements, but the damage is completely repairable! In other words, rather of throwing away a perfectly excellent tent, you may quickly and simply repair the damage (and restore it to its former glory!) to your major piece of outdoor equipment!

To repair a damaged tent fabric, simply follow these three simple procedures. The following tools and supplies are required:

  • Tools: scissors, rubbing alcohol, a clean towel or rag, etc. Repair tape with tensile strength (for repairing cloth rips)
  • Mesh patch (for mesh tears)
  • Mesh repair kit

1. Cut off any loose threads.

When a tent splits, the fabric often sheds fibers and threads into the surrounding area. These dangling parts must be clipped before the tear can be patched back together. Remove any loose threads by cutting them with a sharp knife or scissors.

2. Cleanthe area thoroughly.

Prior to mending any tears in the tent fabric, it is necessary to remove any dust and dirt that has accumulated on it. Using a clean towel, dab rubbing alcohol into the rip and the surrounding area until completely clean.

3. Cut and apply repair tape.

Measure and cut two pieces of Tenacious mending tape with dimensions that are approximately one inch larger on both sides than the tear. When cutting the tape, make sure to round the edges to avoid them peeling over the years. Place the tent fabric on a level surface. Remove the backing from the tape and press the tape against the rip. Firm and equal pressure should be applied to the fabric surface to ensure that the adhesive is properly bonded to the fabric and that no bubbles occur. Repeat the tape procedure on the other side of the rip.

In the case of mesh rips, perform the same procedure as before, but use mesh patches instead.

You now have a robust, water-tight patch that will allow you to restore your tent to its former splendor and strength.

How to Fix a Leaky Tent Seam

Tightly woven cloth is bonded together with thread and sealant or seam tape to form a tent-like seam. The reason for this is because seams are frequently the first spot where water seeps through. After years of usage, the waterproof sealant or tape placed to seams may begin to degrade and wear away, enabling water to seep in through the opening. As a result, there are two alternatives for restoring the waterproofing qualities of a seam: You have two options: 1. use seam tape or 2. use seam sealant.

The application of seam sealant is by far the most straightforward and least complex option.

To fix a leaking seam, simply follow these four simple procedures.

  • A pair of scissors, rubbing alcohol, a clean cloth or a rag, rubber gloves, and Seam Grip sealant (which comes with an application brush) are all necessary tools. A respirator (optional if the application is being done inside)

1.Trim peeling seam tape (if required).

If the seam tape on your tent is starting to tear away, use scissors to clip away any loose tape or torn edges.

2. Clean the area thoroughly.

Clean the length of the seam and the surrounding region that has to be sealed with rubbing alcohol using a clean cloth dipped in rubbing alcohol. All that has to be done is treat the inside of the seam on the inside.

3. Apply seam sealant.

Attention: If you are applying sealant inside, be sure to use a mask or work in a location that is adequately aired to avoid inhaling contaminants. In an open garage or outside on a warm, dry, and somewhat breezy day, the perfect situation would be to practice in. Making use of the application brush, apply an equal coating of Grip Seal sealant to both sides of the inner seam throughout its whole length.

The sealant will enter into the seam and dry to form a waterproof barrier around the seam joint. A one-ounce tube of sealant is intended to seal approximately 12 feet of seam, so measure and apply sealant as needed.

4. Allow seams to dry.

Allow the sealant to dry for 24 hours in a cool, dry location with plenty of air circulation before using. Say goodbye to dripping foreheads and dripping tent walls! It’s now easier than ever to reseal your tent seam, and your tent will look and perform like new!

How to Repair a Broken Tent Pole – Temporary Fix

Tent poles, which serve as the foundation of any shelter, bear the brunt of the pressures that may be applied to a tent by wind, rain, snow, and ice. Poles can splinter, fracture, or shatter at any time, whether in the course of duty or as a result of an unlucky accident while en route. When camping, a damaged tent pole can be mended using a splint or sleeve made from a piece of cloth. A splint can be fashioned from any solid piece of material, such as a tent post, that is strong enough to support the joint.

See also:  Where Is The Rei Co-Op Half Dome Tent Imported From

The following are the actions to take in order to temporarily repair a damaged tent pole in the field.

  • Duct tape
  • Pliers
  • A tent stake or an aluminum sleeve repair kit (for poles with diameters ranging from 7.9 to 8.5 mm)

1. Unbend and clean the break.

If the tent pole is bent but not damaged, gently straighten the pole as much as you can by bending it back and forth. If there is a break, there may be sharp bits of metal protruding from the surface. Remove or bend these sections of the pole using pliers so that the outside of the pole is smooth.

2. Align and attach the splint or sleeve.

For a splint to hold the broken pole in place, line the damaged pole with a tent stake or any other metal rod. Secure each end of the splint to the tent pole with a piece of tape. Similarly, to attach a sleeve to a tent pole, slip the sleeve over the tent pole. Ascertain that the sleeve is aligned such that it is positioned in the center of the break Secure each end of the sleeve to the tent pole with a piece of tape. These short-term “in the field” remedies should be sufficient to get you through the remainder of your camping excursion without incident.

How to Repair a Broken Tent Pole – Permanent Fix

A better long-term approach would be to replace the broken portion of pole with a new one that could be assembled at home. Simply measure, mark, and cut a new pole to replace the old one and you are done! The following are the measures to take in order to completely repair a broken or damaged portion of tent pole. The following tools and supplies are required:

  • Fiberglass replacement kit
  • Aluminum replacement kit
  • Fiberglass repair kit
  • Needle-nose pliers
  • Locking pliers or binder clip
  • Sand paper
  • Masking tape
  • Permanent marker
  • Hacksaw or pipe cutter

1.Unstring existing poles.

To begin disassembling the poles, begin by removing the elastic band that connects the poles together. Pull the knotted end of the chord from one end of the fiberglass poles with needle-nose pliers if the poles are made of fiberglass. To access the knot hook on aluminum poles, remove the end cover and slide it out of the way. Using your fingers, gradually untangle the chord and remove the poles from the chord. Ensure that the poles remain in the proper sequence until you reach the broken pole.

Using the elastic chord

2. Measure and mark replacement pole.

Purchase a replacement kit made of either fiber glass or aluminum, depending on the material of the pole.

Use the broken pole as a reference to measure and mark the new piece with a permanent marker at the same length as the damaged pole. Wrap a piece of masking tape around the mark on fiberglass poles. When it’s sliced, this will assist to avoid sharp edges from appearing on the surface.

3. Cut replacement pole and sand edges.

Make a mark on the new pole and cut it with a hacksaw. After the cut has been completed, use sandpaper to smooth the edges of the cut. When the poles are folded, this avoids any sharp edges from injuring the elastic cord that runs through them. When cutting aluminum poles, a pipe cutter tool produces a far better cut that does not require sanding or other finishing techniques. Insert the aluminum pole into the cutting tool, making sure the mark is aligned with the blade of the cutter. The dial may be used to tighten the blade.

Gradually tighten the blade and continue to spin the tool around the pole until the whole cut through has been completed.

4. Restring poles.

Cut the new pole at the marked location with a hacksaw. To smooth the edges of the cut once it has been made, use sandpaper. When the poles are folded, any sharp edges are protected from injuring the elastic chord. Instead, a pipe cutter tool may be used on aluminum poles to provide a far better cut that does not require sanding afterwards. Insert the aluminum pole into the cutting tool, making sure that the mark is aligned with the blade of the cutting tool. With the dial, you may tighten the blade even further.

Gradually tighten the blade and continue to spin the tool around the pole until the whole cut through has been completed.

Replace and Repair Tent Poles

The majority of modern tents are constructed of glass fiber poles with elastic flowing through the center. If you don’t tighten your guide ropes enough to prevent your tent from shifting about, you may find that these poles split through the middle. Most tent retailers, such as go outside, retain used ones in store from previous show tents; if you ask respectfully, they may be willing to offer you a few of them for free if your tents are less than a year old and you purchased them from them.

Step 1: You Will Need.

Hacksaw and sandpaper for replacing the poles In the shape of a large needle Fishing line with a lot of strength Pen with a marking pen Mask for the face

Step 2: Getting Started

Remove the poles from the elastic by cutting the knot at one end of the elastic and removing the poles from the elastic.

Step 3: Cutting to Length.

Mark the length of the old pole adjacent to the new pole to use as a reference. Hold the new pole firmly in your hands and carefully cut the pole to the desired length, being careful not to damage the fibers. WHEN WORKING WITH FIBERGLASS, ALWAYS WEAR A MASK.

Step 4: Sanding

Using slow, gentle sanding, remove any splinters from the top of the pole, then sand the edges to a cone shape until they are smooth. Check that the poles are snugly fitting into each other by putting them through their paces. WHEN WORKING WITH FIBERGLASS, ALWAYS WEAR A MASK.

Step 5: Threading the Elastic

Using fishing line to thread the elastic knot, thread one end of the elastic through a knot-free fishing line end, and then tie a needle on one end of the fishing line to the knot-free end, you will need approximately twice as much fishing line as the pole length.

Make sure the knot is small enough to fit inside the pole freely. Embroider the pole by inserting the needle and thread inside it and gently tapping it on the floor until the needle is at its lowest point, then gently pulling the elastic through.

Step 6: Last Pole

Holding the elastic around your finger and tying a double knot at the end of the fishing line will help you draw the last two poles tight. Once you have finished, cut the fishing line and you are finished!

1 Person Made This Project!

Tent poles are the primary structural component that keeps your tent in its proper form and position. If the pole is damaged, either intentionally or as a consequence of wild winds, your shelter will not be able to remain straight and stable. It will be distorted and may even collapse altogether, ruining your camping experience. What is the best way to fix a damaged tent pole? Regardless of whether your tent pole is constructed of aluminum or fiberglass material, it is possible for it to get damaged and require repair.

In order to repair a damaged aluminum tent pole, you’ll need a pole repair sleeve that fits the pole.

Repair of Broken Tent Pole –Steps to Follow

Despite the fact that you may purchase high-quality tent poles made of aluminum or fiberglass, it is inevitable that they will wear out or even break over time. Listed below are some of the measures you might want to consider doing in the event that your tent pole breaks.

1.Assemble the tools Tent Pole Repair

In order to fix a success, you will require a set of tools. When you return home, you will have no trouble accomplishing this. If a pole breaks and has to be repaired while camping, you may always bring the following tools with you to your campsites as a backup plan.

  • Needle nose pliers, hacksaw, file, tape, spare shock cable, spare pole section, A wire, and other miscellaneous items

These tools are commonly accessible at hardware stores, as well as supermarkets and online retail establishments.

2.Cut off the Knotat The End of the Broken Pole

There is a knot at one end of your pole that you will need to cut off before you can continue. This will be accomplished quickly if you use needle tip pliers, which will also assist you in pulling the knot out of the pole. Once you’ve finished cutting the knot, you may find that the cable is too short to be reused, in which case you should consider replacing the entire cord. In order to use a new cord, you must choose one that is at least 75 percent of the total length of the constructed pole.

3.Cut the Pole to a Suitable Size

Starting with the length of the old pole, mark it against the length of the new pole, and cutting the new pole at the measured place, you’ll be well on your way. Ensure that you are wearing a mask when cutting the fiberglass, and that you are cutting carefully so that you do not damage the fibers.

4. Do a ProperSanding

The top of the pole should be sanded gently and evenly once it has been successfully cut in order to eliminate any splinters. Then sand the edges as well, until you get a smooth cone-shaped surface. Try fitting the two poles together until they are able to naturally fit into each other, if possible.

5.Replace Your Tent’s ShockCord

This should be a simple and quick process. Simply tie a knot at one of the cord’s ends, leaving a long tail at the other end to make it easier to take the line out the next time you need to repair it. By heating the other free end of the cord on a candle, you may make it smooth and pointed, which will make it easier to thread between the poles. If you don’t want to utilize the shock cord, you may thread the cable through the poles using a piece of wire or a metal rod instead. It is beneficial to use these two alternatives in situations when the cord is not long enough; nonetheless, the cord should be an excellent choice for threading through the poles since it has a suitable degree of rigidity.

Using duct or gaffer tape all around the pole, tape it back together securely to keep the pole back together. However, it is important to remember to complete the repair later on for longer-lasting effects.

Fixing a Broken Aluminum Tent Pole Using Pole Repair Sleeve

The following technique must be followed when using a service sleeve to repair or replace a broken aluminum tent: Step 1: To begin, connect the broken pole portions together in a line. The second step is to straighten the pole if it just has a little bent and is not broken. To fix the tent pole, take the repair sleeve that is generally included with the pole and slip it over the pole until it completely covers the break. Step 4: Wrap duct tape over the ends of the sleeve or pole many times. Additionally, you might use any other form of heavy-duty tape that you are able to conveniently locate.

However, this will make it more difficult to fold the pole when you are attempting to take down the tent in a clean manner.

Fixing a Broken Aluminum Tent Pole With a Tent Stake as Splint

  • Step 1: Arrange the broken portions of the pole in a straight line. Step 2: If the pole is just slightly bent, straighten it. Step 3: Attach the stake to the pole so that it is aligned with the break. 4. Wrap the ends of each stake or pole with duct tape numerous times, or use whatever heavy-duty kind tape that you happen to have on hand
  • 5.

It’s impossible to go wrong with these tips and processes for fixing a damaged tent pole, so you can rest certain that your camping tent will always be in excellent condition. Another thing to remember is that you can always enjoy your camping and outdoor activities without having to worry about repairs or replacements since we have your back. However, it is critical that you take excellent care of your tent poles in order to avoid damage. Tent Pole Repair Kits are available for purchase.

Best Tent Poles for your Tents

Following the selection of the most appropriate tents for your activities, it is critical that you obtain the most appropriate poles for the occasion. When compared to plastic and wood poles, steel is much heavier but also more dependable in terms of strength. Aluminum and fiberglass tent poles are the most suitable solutions for you in this situation. Take a look at what they have to offer to see what you think.

Fiberglass Tent Poles

Following the selection of the most appropriate tents for your events, it is critical that you obtain the most appropriate poles for the circumstances. When compared to plastic and wood poles, steel is much heavier but also more durable and long-lasting. This leaves you with the greatest alternatives for tent poles, which are aluminum or fiberglass in construction. Consider what they have to offer in terms of products and services.

Aluminum Tent Poles

Aluminum tent poles are lightweight, and as a result, they would only be able to hold lightweight tents. They are great for those huge and expensive tents that need to be transported in a light and portable manner. Aluminum is also a strong material, which is why it can sustain the weight of these enormous tents without breaking. Aluminum tent poles are most likely to be used for large-scale events such as weddings. When you use aluminum poles, you won’t have to worry about your tent collapsing under the weight of snow on the canvas, which will keep you and your family safe.

T The tent poles are also extremely flexible, and they are capable of withstanding the stresses of high winds without bending. Because they are able to retain pressure, they are very unlikely to break or shatter when subjected to tremendous stress.

Disadvantages of Aluminum Tent Poles

  1. Tent poles made of aluminum are more prone to corrosion than fiberglass tent poles, and as a result, they may not last as long as fiberglass tent poles. They, on the other hand, are coated with a specific coating that serves as a protective layer. Aluminum is an excellent conductor of heat and electricity: Aluminum is an excellent conductor of electricity. Due of the possibility of being hit by lightning, it may not be a safe tent attachment.

Aluminum Alloy Tent Poles- Replacements

You may find that you need to repair your broken tent poles with a new set ofAdjustable Aluminum AlloyTent Repair Poles from time to time in order to maintain total peace of mind. This set of replacement poles is designed to be used with tents that can accommodate one to two people. Aside from the tent poles, this replacement kit also includes a repair splint in case of an emergency repair situation. The Most Important Characteristics

  • Because it is little in weight, it is simple and convenient to transport
  • It is adaptable, allowing you to delete or add parts as needed. They make it possible to quickly and simply fabricate a suitable replacement tent pole in the event of a broken tent pole. It is constructed of high-quality aircraft-grade aluminum that, when handled properly, has a long service life.

Check out Amazon to see what they have to offer and what they are charging.

Other Related Quick Links

  • In this article, we will discuss how long a good tent should last, how to dry a roof top tent, how to choose a camp chair, and how to keep a roof top tent warm.

Leave a Comment

Your email address will not be published. Required fields are marked *