How To Setup Carbon Filter In Grow Tent

HOW TO SET UP A CARBON FILTER IN A GROW TENT

Make your grow tent clean and odor-free by properly installing a carbon filter system and an inline fan system in your growing space. When growing plants inside, there may be a lot of undesirable scents and potential pollutant issues that can be harmful to both you and your plants’ health if not addressed. Installing a carbon filter and an inline fan system in your grow tent will help to alleviate both of these problems. Mold and mildew contamination concerns are often resolved by maintaining a proactive and clean garden, however not everyone is as conscientious as you may think.

But how can you assure that it is correctly configured to clean the air in the manner in which it is intended to do so?

I’ll go over the most prevalent layouts and explain why one is preferable to the other and why.

Conduit should be run from the filter to the fan and then from the fan to the exterior of the tent.

  1. METHOD 2METHOD 2: INSTALL FILTER INSIDEFAN OUTSIDE GROW TENT METHOD 2METHOD 2: INSTALL FILTER INSIDEFAN OUTSIDE GROW TENT The filter should be attached to the inside of your tent near the exhaust vent, as specified in the instructions.
  2. Check to see that the fan is sucking air from the interior of the tent out to the outside.
  3. Install ducting from the fan to the exhaust port and then to the filter outside the tent to complete the installation.
  4. THE FOURTH METHODOLOGYMETHODOLOGY 4: INSTALL BOTH FANFILTER OUTSIDE THE GROW TENT Directions: Attach ducting to the top of your grow tent, near the exhaust port, and secure it in place.
  5. Attach the filter to the fan and check to see that the fan is sucking air from the interior of the tent out to the outside.
  6. While any of these configurations will produce the intended result, the first configuration is the most effective.
  7. For the second time, the majority of inline fans now on the market indicate in their user manuals that the air entering the fan must be filtered in order to avoid damage or increased wear and tear over time.

Your carbon filter and inline fan are now ready for installation! Make sure to check out my equipment recommendations page for the greatest grow goods available on the market today. Purchase everything you require now and begin developing right away! ​

The Best Place to Install Your Carbon Filter

Cannabis producers are generally concerned about maintaining their privacy since the odor it generates may be quite strong and nasty. Naturally, they resort to powerful odor scrubbers such as a carbon filter, which they can attach to their ducting and use to capture odors in a charcoal bed. While the equipment in a grow tent can be organized in a variety of ways, there is a certain location where a carbon filter should be installed.

The Most Recommended Location

As a result of the strong and unpleasant scent that cannabis produces, most growers want to maintain their privacy when cultivating their crops. To combat this, they use powerful odor scrubbers, such as a carbon filter, which they can attach to their ductwork and use to trap odors in a charcoal bed. The equipment in a grow tent can be configured in a variety of ways, but there is one location in particular where a carbon filter should be installed: the center.

Other Locations

When it comes to cannabis cultivation, most producers prefer their privacy, as the odor it generates may be powerful and terrible. As a result, companies resort to powerful odor scrubbers such as a carbon filter, which they can attach to their ducting and use to capture odors in a charcoal bed. While the equipment in a grow tent may be placed in a variety of ways, there is one location that is excellent for installing a carbon filter.

How To Set Up a Carbon Filter In A Grow Tent

It’s important to remember that while growing inside, the last thing you want is for musty plant aromas to fill your house, unless you’re growing something fragrant and gorgeous. Indoor growth can also create smells and toxins that are potentially harmful, such as those produced by soil, fertilizers, and the plants themselves. The most effective remedy for this would be to incorporate activated carbon filters into your airflow system in order to control smells and pollutants. Using this article, I’ll teach you how to set up a carbon filter in your grow tent, which will allow you to manage and clean the air while still keeping effective circulation.

First let’s start with all the stuff you will need:

  1. Even if you’re growing something fragrant and attractive indoors, you don’t want musty plant scents to fill your house while you’re trying to concentrate on your growth. Moreover, scents and pollutants from soil, fertilizers, and the plants themselves can be produced during indoor cultivation that are potentially harmful. In order to manage smells and impurities, the greatest method would be to incorporate activated carbon filters into your airflow system. Using this tutorial, I’ll teach you how to set up a carbon filter in your grow tent, which will allow you to manage and clean the air while still keeping an efficient air flow. There are many different ways to set up a carbon filter inside your grow tent, and this is just one of them. It is also quite simple.

Once you’ve gathered everything, you’ll be able to begin setting up your carbon filter in your groom room.

Let’s Begin!

The exhaust system is where you should install your filter. When installed on Can-Fan and Max-Fan exhaust fans, Can-Lite activated carbon filters provide long-lasting, constant filtering performance with minimum resistance to cause airflow loss, resulting in lower operating costs. Using clip hangers, the filters and duct inclined fans may be hung from tent supports in rooms with walls and ceilings, or they can be affixed to a solid surface in spaces with no walls or ceilings. Your filter should be installed on the intake side of the fan in order to remove impurities from the airstream before they reach the housing of the fan.

Instead of blowing air into the filter, you should be drawing air through it to avoid dust, mold, and other particles from clogging the activated charcoal in the filter itself.

In order to get optimal airflow in an enclosed grow area, it is necessary to locate the intake fan at the bottom of the room so that the heavier air that collects at the bottom of the room is drawn in by the fan.

Depending on your configuration, it may not be required to exhaust the air that is pulled through the carbon filter outside of the growing area, but rather to return the filtered air to the growth area as soon as it is pulled through the carbon filter.

As a result, the carbon filter will continually “clean” the air in the growing area, removing smells from the environment.

Does it matter if the carbon filter is outside or inside?

In a nutshell, no. You can have the carbon filter outside the grow tent and inside the grow tent, or you can do both at the same time. One of the most important considerations is that your extractor fan pushes the air from your grow room/tent out via your carbon filter as efficiently as possible. It normally doesn’t make a difference as long as the air is passing through the filter; otherwise, foul odors and musty plant odours would emanate from the filter.

How can i reduce the noise and make it smell nicer?

When carbon filters and extractor fans generate a lot of noise, you may wish to put your extractor to a wall for reduced vibration, or you may want to hang your extractor inside the grow tent with the filter to reduce the amount of noise. Using a sponge air freshener within the filter to provide a pleasant fragrance around your grow area is another option. Alternatives include upgrading to acoustic-insulated ducting to eliminate vibrations altogether.

Carbon Filters: Should I Use One in My Grow Room?

So you’ve finished building up your grow room and have begun cultivating some plants in it. Congratulations! You may not be aware of it at first, but gradually you will discover that your growing area has a distinct odor. Chances are you’ll want to keep the smells of your grow area to yourself, whether it’s the strong fragrance of your plants or a slight stench from the humidity in the air. Use of a carbon filter in your grow room is highly recommended, especially if you want to keep the operation’s location secret or if you just want to keep the odours from your growing space out of your home.

What Are Carbon Filters?

A carbon filter, like most other air filters, is intended to cleanse the air that enters it while also exhausting new air into the surrounding area. Using carbon media, these metal cylinders are filled with air and connected to a high-output fan in order to remove smells and particles from the air in your growing environment. In order to accommodate the size of your grow room and the quantity of filtering you want, carbon filters are available in several different sizes and configurations. When your grow room is correctly set up, all of the air from your grow room will pass through the filter, and the scents in your grow room will be completely eliminated.

How Carbon Filters Work

It is, in fact, pretty straightforward: CO2 filters operate by capturing and retaining undesired odors (odor particles) and dust particles, allowing only clean and fresh air to pass through the tube. Carbon filters are made of a variety of materials, however the majority of them, including Yield Lab carbon filters, are made of charcoal. Porous in nature, it may be utilized for a variety of applications ranging from removing specific gases from the air to lining face masks and other protective gear.

Adsorption, which is the act of capturing molecules from the air, is possible through the use of these holes.

Of course, air does not simply float into the carbon to be filtered; it must first pass through the carbon.

In order to prevent dust and odor molecules from escaping or spreading outside your grow room orgrow tent system system, the fan draws in all of the air in your grow room and pushes it through the filter, which effectively blocks the air from leaving your grow room.

Using a Carbon Filter in Your Growing Area

The following are some crucial considerations to bear in mind when it comes time to begin employing a carbon filter in your growing environment:

Find the Right Size

Despite their similarities, all carbon filters are not created equal. Carbon air filters come in a variety of sizes, depending on the size of your growing space and the cubic feet per minute (CFM) value of your exhaust fans. The size of your carbon air filters will depend on these factors. You will need to complete the following procedures in order to calculate the CFM value:

  • The quality of carbon filters varies widely. You may choose from a variety of different-sized carbon air filters depending on the size of your growing space and the cubic feet per minute (CFM) capacity of your exhaust fans. Following are the actions you must do in order to calculate the CFM value: 1.

The most accurate technique to determine what size carbon grow room filter to use is to make sure that the CFM value of your filter is either equal to or lower than the CFM values of your grow room and exhaust fan combined. Consider the following scenario: you have a5ft x 5ft x 8ftgrow tent:

  • Multiply5x5x8. This amount is equivalent to the cubic feet of your growing space (200)
  • The cubic feet (200) are multiplied by the number of exchanges every hour (60), resulting in a total of 12000
  • A total of 200 CFM may be obtained by multiplying that amount (12000) by the number of minutes of exchange in an hour (60). Take the 200 CFM that you now have and seek for a filter that meets or surpasses that CFM

As a general rule, it is usually preferable to exceed your CFM requirements rather than to fall short. If you purchase a smaller filter than you would use, the carbon will be depleted rapidly.

Set Up Your Filter

Once you’ve determined what size filter you’ll need, you’ll want to be certain that it’s set up correctly. In order to get the most out of your carbon air filter, you must make certain that it is filtering all of the air that is circulated throughout your grow room. This implies that you must connect it to a grow room fan and connect ducting to it, and then carefully seal it with duct clamps after that. Place the fan and filter above or near your plants to maximize air circulation. Then, place the fan so that it draws air from your grow room and exhausts it into the filter, as shown.

Maintain Your Carbon Filter

When all of the pores, or adsorption sites, in the carbon are completely occupied, your carbon filter will no longer be able to catch any more molecules in the water. Maintaining your carbon filter is as simple as making sure it is cleaned on a regular basis – generally once a month. To clean your filter, you should first remove it from your grow room and shake it to remove any dust and debris that has accumulated within. Note: Contrary to common perception, cleaning charcoal in a filter with water and soap might actually have a negative impact on the filter’s performance.

See also:  How To Fix Leaking Tent

You will eventually reach a point at which your carbon filter will be unable to trap as many molecules as it used to be able to.

If you begin to detect an unpleasant odor even after cleaning the filter at home, it is likely that you need to replace the filter.

Should You Use a Carbon Filter in Your Growing Area?

The answer to that question is an emphatic one. For keeping the stench from your growing area out of your home and away from your neighbors, carbon filters are the most effective alternative. More significantly, they are the most effective method of ensuring that even the most fresh air is used by your plants for growth. It’s important to note that there are various short-term treatments available, such as air purifiers or neutralizing sprays and powders, that you can employ. Having said that, these instruments will not totally eliminate the odor from your growing operation, nor will they completely eliminate any dust particles that may have escaped from your grow space.

Carbon filters are the most effective way to ensure that your grow room is completely odor-free while also preventing odors from escaping your growing environment. You may begin by locating the most appropriate filter for your grow room by visiting this page.

Carbon Filter Outside Grow Tent- Guide & Warnings

Home»Environment»Carbon Filter Outside Grow Tent- GuideWarnings9075Views0 Carbon Filter Outside Grow Tent- GuideWarnings9075Views0 Perhaps your grow tent isn’t up to the task of housing a 16-pound carbon filter in the first place. However, you still want it to be there in order to filter out the foul odor. In this case, you’re considering installing the carbon filter outside the grow tent. Despite this, it may have certain unintended repercussions. However, it is still feasible to retain the carbon filter outside the tent and ventilate the air so that it does not smell.

Keep an eye out for more information.

Why Put The Carbon Filter Outside Tent?

First and first, this is not a suggested course of action in any way. First and foremost, you should keep your carbon filter (as well as your fan) inside the tent. However, if you find yourself in any of the following scenarios, you may need to reconsider your position-

Your grow tent size is too small

Carbon filters are typically 6″ or 4″ in diameter with a length ranging from 16″ to 24″ in length. If the size of your grow tent is between 10 and 30 square meters (24, 48, 48, etc.), you may have difficulty accommodating the filter.

Your tent might not be strong enough

Most carbon filters have a 6″ or 4″ diameter and are 16″ to 24″ in length, depending on the manufacturer. If the size of your grow tent is between 10 and 30 square meters (24, 48, 48, etc.), you may have difficulty fitting the filter in the space available.

You Don’t Want to Waste Grow Space

The typical carbon filter has a diameter of 6″ or 4″ and a length ranging from 16″ to 24″. If the size of your grow tent is between 10 and 30 square meters (2, 4, 4, 8, etc.), you may have difficulty accommodating the filter.

Items You Need

  1. Carbon filters are typically 6″ to 4″ in diameter and 16″ to 24″ in length. If the size of your grow tent is between 10 and 30 square meters (24, 48, 48, etc.), you may have difficulty fitting the filter inside.

Setting up the Carbon Filter Outside Grow Tent

The following instructions will walk you through the process of installing a carbon filter outside your grow tent. But, before we get started, I believe you should recognize something really crucial! Carbon filters are most often the first step in the process of developing a grow room ventilation system. As a result, the air first passes through the filter, where it is cleansed of unpleasant compounds. Because it sucks air through it, a carbon filter is utilized as an exhaust filter in vehicles.

Instead, air is blasted into the filter, which then serves as an intake filter for the engine.

Setup Guide 1: Fan Inside- Filter Outside

It is recommended that we retain the fan and filter on the inside of the case in case 1. Your grow tent may not be robust or large enough to accommodate the filter in this situation, but a fan would suffice. Now, here are the steps to follow:

Step 1: Prepare the Carbon Filter

Keeping the fan and filter inside is required in Case 1, although keeping them outdoors is optional. Your grow tent may not be robust or wide enough to accommodate the filter in this situation, but a fan would suffice. Here are the steps to follow:

Step 2: Find The Suitable Place for The Filter

Because we’re thinking of putting the filter outside, the carbon filter should be placed as “near” to the vent hole as is reasonably practicable.

The reason for this is that if it takes a significant length of ducting to reach the filter, the airflow will be significantly reduced. As a result, the filtering process of the carbon filter will be slowed down significantly.

Step 3: Cut Ducting at the Required Length

Given that you’ve placed the inline fan within the tent, you’ll need to connect it to the filter on the exterior of the structure. Measure the distance between the fan flange and the filter flange with precision. And then cut the ducting to the precise length you need it with a box cutter or wire cutter. With aduct flanging kit, you can be certain of accurate and leak-free functioning.

Step 4: Connect The Filter Flange with the Fan Flange

The inline fan has to be connected to the filter, which is located outside the tent, because you put it inside. Ensure that you have precisely measured the distance between the fan and filter flanges, as well. Then, using a box cutter or a wire cutter, cut the ducting to the exact length needed. Accurate and leak-free functioning are ensured by using an aduct flanging system.

Setup Guide 2: Both Fan and Filter are Outside

Growers may want to locate both the fan and the filter outside under some circumstances. This is especially true when the fan-filter combination is expected to remain in place. In such instances, you must devise a method of reducing the tremendous amount of noise generated by inline fans. Taking that into consideration, here are the steps-

Step 1: Place the Carbon Filter Ready

Growers may want to locate both the fan and the filter outside in some instances. In particular, when the fan-filter combination is meant to remain in its original configuration. If you have an inline fan, you must find a technique to lessen the large amount of noise it produces. Here are the steps to follow, assuming that assumption is correct:

Step 2: Put the Fan on Top of the Filter

Because we’ll be keeping both the fan and the filter outside, we’ll need to make a fan-filter junction that’s both secure and airtight. Place the fan’s tapered end on top of the filter so that it is flush with the surface. Now, using 1-2 wraps of the aluminum foil duct tape, secure the junction. It’s possible that you won’t receive the duct tape along with the fan-filter combo. As a result, ensure that you have one before beginning the process. Despite the fact that it is standard practice, be certain that the fan and filter sizes are the same.

Step 3: Cut the Vent Hole and Ducting

The fact that we’ll be installing our fans and filters outdoors necessitates the construction of an airtight and secure fan-filter connection. Place the fan’s tapered end on top of the filter so that it can’t be seen. After that, use 1-2 wraps of the aluminum foil duct tape to seal the connection in place. It is possible that you will not receive the duct tape with the fan-filter combination. As a result, make certain that you have one before beginning the process. Despite the fact that it is common knowledge, make certain that the fan and filter sizes are the same.

Step 4: Secure Connections

Duct foil tape and duct clamps should be used to secure all of the connections. The connections that should be beneath the rudder are the vent-ducting junction, the ducting-fan joint, and the fan-filter joint.Problems- The vent-ducting joint is a common source of problems.

  1. It is possible that the fan will not suck as much air from the outside as it might from the inside. When the fan is located outside, it will be incredibly difficult to reduce inline noise.

Consequences of Keeping The Filter Outside Tent

It is possible that the fan will not suck as much air from the interior as it might. The inline noise fan reduction will be exceedingly difficult to achieve when the fan is outdoors;

You’re Defeating The Purpose of the Pre-filter

The pre-purpose filter’s is to filter out large-sized dust and debris from the inside of the grow tent. Because you are preventing the filter from working, you are undermining its function. As a result, the dust and debris will be drawn straight into the fan’s airflow. This is a complete and utter no-no. Remedy: Place the pre-filter on the opening of the vent hole (in the case of a ‘fan-filter combo outside’), or on the opening of the inline fan (in the case of a ‘fan inside, filter outside’) to prevent the fan from turning on.

You Can Not Draw Air Through The Filter Anymore

Despite the claims of many manufacturers, carbon filters are not equally effective in drawing air in and out of a system from both directions. In this situation, we’re extending it outwards from the center. And this will result in a decrease in the effectiveness of the filter. Additionally, this inefficiency may have an impact on the predicted output from your growing space. Treatment:There is no effective treatment for this. You’re going to have to deal with the problem one way or another. However, placing an oscillating fan at the bottom of the structure may help to circulate the air and decrease the impact to some amount.

The Fan has to Work Harder

Irrespective of whether the fan is located inside or outside the tent, it must exert more effort in order to direct exhaust air into the filter. If there are a few of turns in the ducting, the job may become much more difficult. Solution: Purchase a fan that has at least 5-10 percent greater CFM than the one recommended by your grow system. Maintain the ducting’s length and straightness to the greatest extent practicable.

It Might Catch on A Fire

We can see from the preceding statement that the fan is subjected to a great amount of strain when the filter/fan-filter combination is located outside the building. An increase in pressure may induce overheating in the fan motor, which may result in a failure. In the worst-case scenario, it might even result in a fire. Solution:In this case, we strongly advise you to go for inline fans that are equipped with circuit breaker help. If the fan experiences any further stress or heat build-up, it will immediately shut down and turn off.

Safety Concerns

We can see from the preceding statement that the fan is subjected to a great deal of strain when the filter/fan-filter combination is located outside the house. Due to the increased strain placed on it, the fan motor may overheat and eventually fail. Even a fire might result in the worst-case scenario. Solution:In this case, we strongly advise you to invest in inline fans that are equipped with circuit breakers. If the fan experiences any further stress or heat buildup, it will shut off immediately.

  • Electric fans with circuit breakers should be used
  • Ducting should be kept short and straight
  • Install a pre-filter at each point where air will come into contact with the ducting to filter it. Utilise an air-conditioning fan that delivers 5-10 percent more CFM than the grow system requires. Make sure you utilize an electric inline fan with a circuit breaker
  • Otherwise, the fan will not work.

I’m Saleh, and I’m a blogger that enjoys doing home improvement projects on the side.

Whatforme.com is my tiny corner of the internet where I can communicate what I’ve learnt first-hand, particularly in the field of home repair. The most recent posts by smsaleh (see all)

How to Set up a Carbon Filter in a Grow Tent or Grow Box

If you’re growing inside, the last thing you want is for your house to smell like a musty plant, unless, of course, you’re growing something that smells delicious! Using this brief tutorial, I’ll walk you through the process of installing a carbon filter in your grow tent. Please keep in mind that there are many other ways to set up a carbon filter inside your grow tent, and this is just one of them that is extremely simple to do. First and foremost, you’ll require the following miscellaneous items:

  1. If you’re growing inside, the last thing you want is for your house to smell like a musty plant, unless, of course, you’re growing something that smells really delicious. You will learn how to install a carbon filter in your grow tent in this short instruction. There are many different ways to set up a carbon filter inside your grow tent, and this is just one of them. It is also quite simple. To begin, you’ll require the following miscellaneous supplies:
See also:  How Many Plants Can I Grow In A 4X4 Tent

Once you’ve gathered the materials, you’ll be able to set up your carbon filter in your groom room in five simple stages.

  1. Make sure your extractor fan is outside of the grow tent while not in use. Connect the ducting to your carbon filter and tighten the duct clamps to ensure a good connection. Mount your carbon filter to the roof bars of your grow tent using YOYO hangers to keep it in place. Distribute the ducting via one of the ventilation holes in your grow tent
  2. And Construct an extraction system by connecting the ducting to the extractor fan with duct clips.

You’ve completed your task! An example of a carbon filter installed within a grow tent may be seen below. There are several different ways to skin a cathang a filter, including: One often asked issue we receive here at GrowGenius.co.uk is whether the carbon filter / fan should be placed inside or outside the grow tent. The answer is easy — you can do both at the same time! Ensure that your extractor fan draws all of the air from your grow room out via your carbon filter. It doesn’t matter which direction your extractor fan is configured as long as all of the air is passing through the filter.

As a result, carbon filters and extractor fans might create a lot of noise at times.

  • Install your extractor against a wall to reduce vibration. If you like, you may hang your extractor fan inside the grow tent next to the filter
  • Set an air freshener with a sponge inside your filter to provide a nice fragrance throughout your grow space. Upgrade of acoustic ducting in order to reduce vibrational noise

Gorilla Grow Tent Carbon Filter

4×12 6×24 8×24
Duct Size 4″ 6″ 8″
Length 12″ 24″ 24″
Airflow Rating 200 CFM 500 CFM 700 CFM
Weight 7.6 lbs. 17.75 lbs. 21.9 lbs.
Carbon Type Coconut Carbon Coconut Carbon Coconut Carbon
Bed Thickness 2″ 2″ 2″
Recommended Tent Size 2×2, 2×4, 3×3, 4×4 5×5, 4×8, 5×9 8×8

It includes a pre-filter as well as GGT branded elastic bands. Promotions and discounts are not currently available to you.

The Gorilla Standard of Carbon Filtration

One of the most important aspects of indoor gardening is the availability of clean, contaminant-free air. Gorilla Tactical Carbon Filters employ only Ultra-Activated Coconut Carbon for maximum adsorption and peak efficacy in removing viruses and smells. Ultra-Activated Coconut Carbon is the most effective carbon available. The supply of carbon is critical to the efficacy of your filter’s carbon filtration system. Because it contains a substantially greater density of micro-pores than other kinds of activated carbon, such as the bituminous coal used in ordinary odor filters, Ultra-Activated Coconut Carbon is a superior odor filter.

  1. In order for plants to grow and develop, they require fresh, clean air.
  2. Those tiny agents of devastation in the air are continually attempting to invade your growing environment.
  3. Enhanced Efficacy Longer-Lasting Effects: Gorilla Tactical Carbon Filters provide up to 50 percent more carbon surface area than standard “pellet” filter alternatives since 80-90 percent of our coconut carbon structure is made up of micro-pores.
  4. Designed with thick carbon beds, Gorilla Tactical Carbon Filters are able to remove the largest amount of volatile organic compounds, smells, and pollutants from the air they purify.
  5. For 4″, 500cfm for 6″, and 700cfm for 8″, the flow rate is 200cfm.
  6. This carbon originates from a renewable crop rather than from a mining operation or a chemical process, making it by far the most environmentally benign and sustainable source of carbon.
  7. Gorilla Swagger is a slang term for a person who swaggers around in a gorilla suit.
  8. With the best-looking carbon filter ever created, you’ll be the envy of everyone you know!

On the downside, there is no warning light on the filter to let you know when it is time to change it. The Gorilla Tactical Carbon Filter is anticipated to last between 12 and 18 months on average, however many have reported that it has lasted considerably longer.

Grow Tent Fans – Sizes, Placement, Setup, FAQ (Updated 2022)

It is critical to have adequate circulation in your grow tent if you want to avoid mold and powdery mildew from forming on your cannabis. Throughout this article, I’ll cover all you need to know about choosing an inline fan for your grow tent and how to correctly install and configure it as well. How to choose the right grow tent fan size and power rating, where to install the fan, how to set up your grow tent fan, and what additional accessories you’ll need are all things I’ll assist you with.

Selecting the proper grow tent fan size and power:

“What is the right grow tent fan size?” is definitely one of the first questions you’re thinking about. as well as “What is the recommended grow tent fan power?” Generally speaking, when it comes to replenishing air in a grow room, the rule of thumb is that you should be able to replace all of the air once each minute. That is the CFM rating, which you will learn more about further down. In order to keep your grow tent cool, the fan diameter will be decided by the CFM (cubic feet per minute) rating that you want.

So don’t be concerned about having the correct CFM rate.

Then there are a few other factors, such as a 25 percent drop in fan power if you include a carbon filter, and a 30 percent loss in fan power for each 90-degree curve in your ducting.

The proper size fan for a 4×4 grow tent:

Let me give you an example of how to calculate the area of a 4×4 grow tent, which is a fairly typical size among indoor growers: The majority of 4×4 tents have dimensions of 48 in x 48 in x 80 in. As a result, the total volume of air in a 4×4 grow tent is 4ft (length) x 4ft (width) x 6.667ft (height) = 106.67 cubic feet (4ft (length) x 6.667ft (height). However, this does not imply that you require a 106 cfm fan. When you consider that a carbon filter will lower your fan efficiency by 25 percent, and that one 90 degree duct bend would reduce your fan efficiency by another 30 percent, a fan that produces 215cfm will produce 112cfm (200cfm x 0.7 x 0.75).

What size fan is needed for other grow tent sizes?

(Click on image to expand) It is important to note that grow tent inline fans are not made to the precise CFM output you want, thus you may have to go over by 50-100cfm when selecting a fan for your grow tent. I recommend using a fan with variable speed settings, such as the AC Infinity S or T Series, so that you may modify the CFM to meet your precise requirements. Each of the AC Infinity fans listed below has ten speed options, so if you just want 100cfm, you may get the most basic model, which is a 205cfm fan, and run it on the middle speed level to achieve that volume of air.

Grow tent fan placement:

The image may be seen in more detail by clicking here. Please keep in mind that grow tent inline fans are not produced to the precise CFM output you want, therefore you may have to go over by 50-100cfm when choosing a fan for your growing environment. In order to customize the CFM to your exact requirements, I propose a fan with changeable speed settings such as the AC Infinity S or T Series.

Each of the AC Infinity fans listed below has ten speed options, so if you just want 100cfm, you may get the most basic model, which is a 205cfm fan, and run it on the middle speed level to achieve that volume of air.

Grow tent fan setup:

Yes, the diameters of your inline fan and duct will need to be the same at the place where they connect.

Passive or Active Air Flow For Your Grow Tent?

The sorts of fan sets you may utilize in your grow tent or growing room are passive and active. Passive fans are the most common. The difference is whether you want air to passively re-enter your grow tent or if you want it to aggressively re-enter your grow tent. Passive grow tent air circulation relies on a single inline fan to evacuate hot air from your grow room, reducing the need for additional fans. When air is forced out of your enclosed grow area, the pressure in the room drops to a negative pressure, which means that air from outside the tent or room should naturally be drawn in via any openings to replace the air that has been forced out of the space.

  • If you want to guarantee that the air returning to the tent is being filtered, or if the air returning to the tent is not returning rapidly enough, active grow tent air replacement is the best option for you.
  • Simply ensure that you have the right size ducting (which should be the same diameter as your fan), duct clamps, hangers for hanging, and zip ties before beginning (make sure zip ties are long enough to go around the diameter of your carbon filter).
  • To install the filter, just attach ducting to the side of your fan that is responsible for sucking in air.
  • Clamps should be used on both sides (usually provided).
  • If you’re using an active air flow configuration, I’d recommend operating both fans at the same speed to ensure that the quantity of air escaping the grow tent equals the amount of air returning to the grow tent.

How to install a grow tent fancarbon filter inside your tent:

If you have a grow tent or growing room, you may employ one of two sorts of fan setups: passive or active. If you want air to re-enter your grow tent passively or actively, the difference is that you want it to do so automatically. One inline fan is all that is required for passive grow tent air circulation, which exhausts the heated air from your grow room as quickly as possible. When air is forced out of your enclosed grow area, the pressure in the room drops to a negative pressure, which means that air from outside the tent or room should naturally be drawn in via any openings to replace the air that has been forced out by the removal of oxygen.

  • If you want to guarantee that the air returning to the tent is being filtered, or if the air returning to the tent is not returning rapidly enough, active grow tent air replacement is the best option for you.
  • Simply ensure that you have the right size ducting (which should be the same diameter as your fan), duct clamps, hangers for hanging, and zip ties on hand before beginning (make sure zip ties are long enough to go around the diameter of your carbon filter).
  • However, I strongly advise using one.
  • Connect the opposite end of that duct to the filter.
  • Make use of a clamp to hold both sides together (usually provided).

It is recommended that if you are using an active air flow configuration, you operate both fans at the same speed to ensure that the amount of air leaving and entering the grow tent is equal.

Other Inline Fan Installation Notes:

The setup is straightforward; it took me no more than 30 minutes to complete my AC Infinity T4 installation. The most efficient design would be to route the duct out a window so that the hot air from your tent does not just blow into the room where your tent is placed, where it would be sucked back in and render the entire operation ineffective. Not everyone has the benefit of having a window in close proximity to their camping site. In that case, if you’re compelled to blow tent air into the same room where the tent is placed, I highly recommend investing in a portable air conditioner to re-cool the air before sucking it back into the tent through the bottom tent windows.

Does It Matter What Carbon Filter I Choose For My Grow Tent Fan?

When selecting a carbon filter for your grow tent fan, the one thing you want to be certain of is that the diameter of the connection point on the fan and the filter are the same. Make certain that your inline fan is equipped with a four inch carbon filter if your fan is four inches in diameter. Apart from that, there isn’t much of a difference between carbon filters; they’re simply large metal canisters that filter your air through charcoal to remove impurities and odors from it.

Do I Need an Oscillating Fan in Addition to my Inline Fan?

Even though the inline fan removes and replaces the air in your grow tent, it performs a poor job of circulating the air. As a result, you should think about including an oscillating fan in your grow tent to keep the air circulating and prevent mold and mildew spores from taking root. It will also aid in the distribution of fresh air for the benefit of the plants. There are little affordable oscillating fans that you can attach into the grow tent poles if you have a look at the fans I’ve listed below.

See also:  How To Clean Tent After Camping

Which Grow Tent Fans I Recommend:

As long as you’re willing to purchase the ducts and hangers separately from the fans, AC Infinity offers fantastic grow tent fans. Purchasing the ducts and hangers is simple – simply match the duct diameter to the fan diameter. What is it about the AC Infinity fans that makes them so much superior than the competition? This fan is equipped with a programmable controller, which allows the fan to switch on in response to a range of different scenarios. For example, you may program the fan to turn on when the humidity reaches a given threshold.

  1. You may also set a timer and receive alarm notifications.
  2. When my AC Infinity T4 was running at maximum power, I was pleasantly pleased at how quiet it was.
  3. This results in the fan motors being loud.
  4. Quiet Inline Duct Fans With Temperature and Humidity Control – CLOUDLINE SERIES Them fans are priced similarly to other fans without the technological characteristics, therefore it makes financial sense to purchase one of these instead of another fan.

The fans are available in three sizes: 205cfm, 351cfm, and 750cfm (4-inch, 6-inch, and 8-inch). Click here to see whether they are available on Amazon.

VivoHome Inline Fan Kit

If you don’t want to go through the trouble of sourcing all of the components separately, this kit includes a fan, 8 feet of ducting, clamps, hangers, and a carbon filter. It is available in two different sizes to accommodate different grow tent sizes. With this kit, the main drawback is that the fan cannot be programmed to come on when particular conditions are fulfilled, such as a certain temperature or humidity. The fan has a simple on/off switch. Despite the fact that some customers have stated that they are content with the fan running all of the time.

Secret Jardin Clip On Monkey Fan for Grow Tents:

Secret Jardin created this 6-inch clip-on oscillating fan with a grow tent owner in mind when they created this product. The clip is designed to attach securely on the support poles of grow tents. The fan will ensure that your grow tent has adequate air circulation, which is necessary to avoid the growth of mold and powdery mildew. I’d recommend using one of these oscillating clip fans in conjunction with an inline fan in order to maintain the ideal growth environment in your grow tent.

Keeping Your Grow Tent Cool

When it comes to keeping your grow tent temps under control, you may want more than simply an inline fan. My best recommendation, without requiring you to read the entire post, is to consider purchasing a portable air conditioner for the room in which your tent is placed, or to consider adding CO2 to your growing environment, which allows you to grow a few degrees hotter than usual. See my whole post on decreasing grow tent temps for more information.

Ideal Grow Tent Temperature and Humidity for Growing Cannabis:

When it comes to keeping your grow tent temperatures under control, an inline fan is not always enough. Rather than having you read the entire text, my best recommendation is to think about investing in a portable air conditioner for the room in which your tent is located, or adding CO2 to the mix, which allows you to grow a few degrees hotter than usual. For more information on decreasing grow tent temps, please see my whole article.

Other Resources for Growing Cannabis Indoors:

I developed numerous useful lists and tips to assist you in completing your home improvement project the right way, in addition to determining the proper fan size for your needs. The following are some other articles I strongly recommend: Choosing the Proper Size Grow Tent, This Year’s Best LED Grow Light List, and Understanding Grow Light PAR PPFD and Wattage, among others. Last but not least, don’t forget to check out myhome page for a comprehensive collection of useful resources.

Grow Tent FanCarbon Filter FAQ:

You’ll just need 30-45 minutes to complete this task.

What should I do if there isn’t a CFM output for my exact grow tent size?

You’ll just need 30 to 45 minutes for this.

If I’m buying parts separately, how do I know if they’ll all fit together?

The diameter of all of these components is the same. If you purchase a 6′′ fan, be sure you also purchase 6′′ ducting and a 6′′ filter to complete the installation. That’s all there is to it, really.

Do I need to hang the carbon filter?

The carbon filter should be placed at the top of your tent in order to capture the warmest air because it is where air will reach your fan from the outside. It would be inefficient to hang the filter low or to place it on the floor, for example.

Which end of the grow tent fan do I connect the carbon filter?

Connect the carbon filter to the “front” of the fan, which means that the fan is sucking air through the filter rather than expelling air through it, and that the fan is running continuously.

What size fan will fit in my grow tent?

Most grow tents accommodate 8-inch ducting, while some may only accommodate 6-inch ducting.

What if the size of my duct is too big for the duct hole on my grow tent?

If your grow tent outlet is 6 inches in diameter and your ducting is 8 inches in diameter, you’ll need to purchase a ducting reducer.

There’s too much negative pressure in my grow tent

Ducting reducers are required when using 8-inch ducting for a grow tent outlet that is 6-inch in size.

Can you wash or clean carbon filters after extended use?

It is possible to clean a carbon filter using compressed air. The filter may be used for up to one year before it has to be cleaned.

Can you place a carbon filter on each side of your fan?

Yes, although it may result in a slight reduction in the power efficiency of your fan. Check to see if your fan is strong enough to manage the additional carbon filter load.

Do all carbon filters come with pre-filter wrap for the exterior of the canister?

Pre-filter wrap is not included with all carbon filters; thus, if you want a pre-filter included, be sure to check the product page specifics before purchasing.

What’s the largest outer dimension of my carbon filter?

Increase the output size by approximately 2 inches. On a 4 inch carbon filter, the canister diameter would be approximately 6 inches in diameter.

How long do carbon filters last?

Carbon filters are designed to endure for at least one year of continuous usage.

Do I need inline and oscillating fans in my grow tent?

Inline and oscillating fans serve various functions in the grow tent, so it’s a good idea to use both if you have the option.

DIY Carbon Filter Step-by-Step Guide [+Why you Need One]

It is critical to provide your plants with the best possible environment in order to produce a healthy and vigorous yield. One method of assisting in the creation of the plant’s natural environment is to incorporate a grow tent into your hydroponic system. With the support of fans and lights, as well as supplying an appropriate supply of water and nourishment, a grow tent may help you achieve your hydroponic goals. A prominent reason for the popularity of grow tents is that they allow for the creative use of growing areas.

Grow tents have gained in popularity as a result of their energy efficiency, which allows you to get the most out of your investment.

When it comes to your grow tent, ensuring sure that it has adequate ventilation is essential for the health of your plants.

What Exactly is a Carbon Filter?

Scrubbers are pieces of equipment that are installed to the exhaust system of grow tents to filter out carbon monoxide and other pollutants. It is made of activated carbon material, which has been used for detoxifying purposes for centuries and is still in use today. It is customary to install carbon filters to the inline duct fan or the tail end of the ducting system. This permits the carbon filter to effectively clean the air that circulates throughout the building.

How Do Carbon Filters Work?

Carbon filters, when installed in your exhaust system, physically capture the odor, dust, spores, pollen, and other impurities that would otherwise be released. Air that has been polluted by pollutants is brought into the room through the exhaust system, where it is treated before being expelled clean and odor-free.

As you can think, the outcome is cleaner air for your plants, which is beneficial. This air is cleaner, free of smells, spores, and other allergies, and it is more breathable. A excellent carbon filter, on the other hand, might be quite beneficial if you have an odor problem caused by your plants.

Benefits of Using a Carbon Filter for your Grow Tent

The use of a carbon filter as part of your exhaust system physically captures the odor, dust, spores, pollen, and other impurities in the filter itself. Air that has been polluted by pollutants is brought into the room by the exhaust system, where it is treated before being expelled clean and odor-free. This results in cleaner air for your plants, which is exactly what you’d anticipate. There are less scents, spores, and allergies in this air, making it more pleasant to breathe. A excellent carbon filter, on the other hand, might be really beneficial if you have an odor problem caused by your plants.

Supplies Needed for DIY Carbon Filter:

  • A polyester filter medium such as knee-high socks will suffice as a pre-filter
  • For the Body (outer mesh): a mesh pencil holder (about 4.5 inches in diameter)
  • A mesh bin
  • For the Body (inner mesh), you’ll need a mesh pencil holder (about 4 inches in diameter) and a PVC drain pipe. In order to make the Activated Carbon Bed, you will need the following items: scissors, zip ties, measuring tape, drill machine, drill bit (5/32, if feasible), and a drill bit (5/32 if possible).

To use as a pre-filter, knee-high socks or other polyester filter material will suffice. A mesh pencil holder (about 4.5 inches in diameter) and a mesh bin are needed for the body (outer mesh). a mesh pencil holder (about 4 inches in diameter), and a PVC drain pipe are used for the body (inner mesh). In order to make the Activated Carbon Bed, you will need the following items: scissors, zip ties, measuring tape, drill machine, drill bit (5/32, if feasible), and a drill bit (if possible).

FAQ

Depending on your requirements, available space, and configuration, the carbon filter may be placed either inside or outside your grow tent. To install the carbon filter inside your grow tent, attach it to one side of the tent and the fan to the other side of the tent at the exhaust outlet, following the manufacturer’s instructions. If you want to run ducting from the filter to the fan and then from the fan to the exterior of the tent, that is an option. Once this is completed, check to see that the fan is successfully drawing air from the interior of the tent to the outside of the tent.

If you have a limited amount of space within your grow tent, you may want to consider setting up your carbon filter and fan outside your grow tent instead.

You may now connect the ducting from the interior of the grow tent to the outside of the tent by passing it through the exhaust port.

Always check to see that the fan is drawing air from the interior of the tent to the outside of the tent.

How Often Should You Change your DIY Carbon Filter?

Carbon filters can be placed inside or outside your grow tent according on your requirements, available space and set-up requirements. The carbon filter should be placed on one side of the growing chamber and the fan should be placed on another side near the exhaust outlet to set up your grow tent’s carbon filter and fan configurations. The ducting from the filter to the fan, and then from the fan to the exterior of your tent, are also options. Check to see that the fan is drawing air from within the tent to outside the tent when this is completed.

It may be preferable to place your carbon filter and fan outside your grow tent if you have a limited amount of room inside.

You may now connect the ducting from the interior of the grow tent to the outside of the tent by routing it via the exhaust port.

Next, install the carbon filter to the fan using the included hardware. Make sure the fan is pushing air from within the tent to the outside at all times by checking it often.

Leave a Comment

Your email address will not be published. Required fields are marked *