How To Rethread Tent Poles - Welcome to Tamborine Mountain Caravan Camping

How to Repair Tent Pole Elastic Cord (Re-thread) – the Easy Way

Determine the diameter of the cord that has to be replaced. When it comes to low-cost tents, this will often be approximately 2mm in diameter, which is not particularly sturdy or long-lasting. Depending on how large the opening diameter is of the pole, you may be able to utilize a thicker diameter than you originally planned. I increased the diameter of the cable on my tent poles from the standard 2mm to 3mm. The cable may be purchased on eBay for a reasonable price. I live in the United Kingdom and purchased 10 meters for around £3.

In order to set up a two-person dome type tent with two tent poles, you’ll need at least ten meters of space.

In an updated version of this post, I measured the original cable and discovered that it was half the length of the poles after they were completed.

Step 2: Find Your Threader

A threader, which you will need to obtain, will be required to feed the cord through. An nice metal threader was discovered within an old windshield wiper, which I was able to save. Consequently, when it is time to replace your windshield wipers, save them or borrow some from your neighborhood auto repair shop. The wiper blade assembly has two strips of metal that span the length of the wiper blade. You must remove these strips of metal from the wiper blade assembly. The greatest wiper blades are those from a saloon vehicle or a van since they have the longest blades available.

Please keep in mind that my photo displays a windscreen wiper, however it is too short.

Metal inserts are uncommon to be found in the lower-priced wiper blades.

Step 3: Join Threader to New Cord

It is now necessary to connect the threader to the new cable. This is accomplished by joining the threader and cable together using a butt joint and then fastening the junction with a very little quantity of adhesive tape. In this shot, I used one revolution of double-sided adhesive tape. Use only a little amount of tape, as too much will cause the threader to drag and cause it to stick to the inside wall of the tent pole.

Step 4: Remove Old Elastic Cord and Re-thread New Cord

Push the threader through the pole aperture after you have cleaned out the old cable from the poles. When it is sliding smoothly, slowly draw the threader through to the other end, where it should poke out the other end. Remember that if this is tough, it is likely that you have too much adhesive tape. Having passed through, pull the threader back through and continue to thread all the remaining poles.

I use up the old elastic cord because I’m a thrifty person. lanyards and neck cords can be made out of the old cord if necessary. I strung all of my USB storage sticks from the old cord that had frayed.

Step 5: Tension Cord and Tie Off the Ends

Trial and error is required to achieve the desired tension, so after threading the entire pole, experiment with your cord tension. The tension must be light enough to allow the poles to be pulled apart, yet firm enough to keep them together when threaded through the tent’s opening. The figure of eight knot is my preferred method of tying off the ends because it is a bigger knot that is also easy to alter. A more substantial knot at the end will last longer. You can then cut the cord after the tension has been reached to your satisfaction.

Step 6: Finished – Store Threader for Next Repair

You should have completed the repair of the tent poles by now. Remember to have your threader handy for when you need to repair your tent! I hope you have found this information beneficial. Thank you for taking the time to watch!

Be the First to Share

GreetingsElastic threaded through one of the poles of my family tent has been kapput. Do you have any suggestions for rethreading it? First, use a coat hanger to make a thin cord, then thread some shockcord through it. 3mm? It will be quite a ball pain because it contains 8 or 10 pieces. thanks In response to toiksander: Is it possible to use gravity and a safety pin on a thread to draw new cable through? In response to toiksander: I’ve done this a zillion times, and you’ll find that the shock cord can be pushed through the poles while giving them a slight twist as you do so.

1) Thread the elastic through the first pole and tie off one end of the elastic to keep it from coming out.
3) Tighten the elastic until it is taut, then clove hitch the tensioned elastic to something sturdy, such as a pencil.
You may also insert a large safety pin into the elastic to prevent it from retracting farther.
Repeat steps 3 and 4 until all of the threading is complete, and then make a knot in the elastic to prevent it from retracting.
Gavin Post was modified at 14:31.
That’s exactly what I was thinking.
It is difficult to untie once the knot has been strengthened.

Take note of whether the shock cable is connected into a detachable end piece on the pole; this is typically very lightly cemented in place to prevent it from falling out.

Keep old tents free of poles and bring them in for repairs on a regular basis.

In response to Brownie: you may use a long length of bent wire to accomplish your goal.

Captain Paranoia received the following response: Heavier sea fishing nylon line was the only thing I was able to get through the fiberglass type pole I was using.

As long as you can attach the shock cord to the end of it, it will operate well, and it is simple to push through the pole.

The metal and huge pole sections have been covered by the majority of these.

Heat Make a larks foot and a seal at the end of the elastic, then stitch a portion of yarn that is longer than the pole as close to the end of the elastic as possible to ensure that the elastic pulls straight.

Keep the cordage and pole in a straight line to avoid damaging the pole end or abrading the yarn, which will cause it to snap (later) If you do, a consistent, solid pull will get you through to the finish line.

and then repeat the process If you still have the old elastic inside the pole, could you hook the new bit to the end of it and pull it through? In response toiksander: This subject has been archived and will no longer accept new posts in response to it.

How to Replace Shock Cord in Tent Pole

There are various little components in a tent that might fail, but these do not need the purchase of a completely new unit. Tent pole shock cords are susceptible to failure, deterioration, and brittleness with time, and finally loss of their elastic qualities. Your tent pole may no longer operate properly if the shock cord is no longer functioning properly. You may believe that new tent poles are required. Purchasing new tent poles, on the other hand, may be quite expensive, and there is a lot more affordable option.

It is simple to replace the shock cord in your tent pole; all you need are a few simple components and a positive mindset.

We’ll also talk about why shock cords are vital, as well as some preventative actions you may do to avoid more harm.

If you know how to mend a broken tent pole in the field, a broken tent pole in the field does not have to be a reason for panic.

What is a tent shock cord and why is it important?

Modern tent poles are equipped with shock cords, which serve primarily to keep your tent poles connected to one another. Tents of the past had poles that easily split apart into tiny portions, however the newer design preserves all of your poles in one piece and makes pitching your tent much simpler. You may still utilize the fragments of a broken shock cord from one of your poles if the cord is from another pole. Nonetheless, because your tent poles are intended to be linked, pitching your tent may prove to be a significant issue.

Upon assembly of the poles, the shock cords are formed of an elastic material, which allows for the individual segments to be kept together with elastic once the poles have been joined.

What you need to replace the shock cord in a tent pole

Before settling down to repair your tent, make sure you have all the materials necessary. You may buy a replacement shock cord at your local camping store, and there are several suppliers online as well. You will need:

The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
Scissors or a sharp edge
Measuring tape
Sharpie or marker pen
A lighter or matches to melt the ends of the wires Tape for masking

How to replace a faulty shock cord in a tent pole

The moment has come to get started on mending your shelter now that you have all of the equipment you need, as well as some new shock cable to replace the old, faulty ones you had to start from scratch. If you follow our instructions, your tent will look and function like new! The first thing you should do if your shock cord is still intact is to cut it with scissors by pulling apart two portions of your tent pole and severing the shock cable within them. You will see that your tent pole will come apart into its many components after the cable has been severed.

Because it’s probable that the pole portions in the middle are similar, the end pieces where the rope is knotted are the most critical parts to avoid getting mixed up in the process.
Perhaps you’ll need to remove your grommet pegs and then untie the remaining cable before you can continue.
2.
Remember to collect the proper dimensions for each tent pole if you’re replacing the shock cord in a number of different models.
Make a mark on the cord using a marker pen to indicate the length that will be needed, but do not cut it yet!
If you are unable to use your previous cord as a reference, measure and mark the new cord to be approximately 8 inches shorter than the pole, or around 75% of its overall length.
You’ll need to cut the cord to a length that’s slightly longer than the length of your tent poles in order to leave enough room to thread it through.

Then, taking the longer end, begin threading it through all of the segments of the tent pole until you reach the other end.

Make certain that the cables are threaded in the proper direction, male to female, or else they will not fit together after you’re through.

Step 4: Finish the job 4.Assemble the tent pole so that all of the sections are attached to one another, just as you would while pitching a tent.

When all of the tent pole sections are securely fastened together, begin tugging on the cord to stretch it out at the other end.

When you’ve reached the desired length with the string, tie a knot here to ensure that the peg is secure.

Then, using your lighter or matches, singe the end of the cord to prevent it from fraying or unraveling.

All of the components should be tucked away and reassembled, and there should be no evidence of a shock cord visible outside the pole.

We’ve come to the end of our lessons on how to replace the shock cable inside a tent pole.

All camping equipment is subject to wear and tear, but for the most part, it is not required to replace it.

The fact that you can use this approach at home when doing repairs is excellent, but what happens if your shock cord breaks while you’re on a camping trip isn’t so nice.

If you don’t happen to have an extra length of tent pole shock cord on hand, continue reading to learn about potential alternatives to this procedure.

How to Repair a Shock Cord if it Breaks in the Field

A snapped or overstretched shock cable might make erecting your shelter more difficult if you’re already out on the trail during your camping vacation. If you want to repair the wire without having to replace the entire length, fortunately, there is a simple solution. However, while this is not a permanent solution, it will allow you to use your tent for a short period of time until you can replace the cord completely. If the cable hasn’t snapped, but rather has become too stretched out to go around your tent pole, there’s a simple solution.

Then, draw the shock cable through the grommet peg until it is taught once again, and reattach it to the grommet peg.
If the shock cord on your old tent pole has snapped, you’ll need to remove the pole using the steps outlined above to fix the problem.
Remove a few inches of the cord’s elastic core on each side of the break, leaving only the braided sheath on the other side.
The reason you need a thinner segment of cord to tie the knot is so that the knot will not become trapped in the poles and will be able to flow through freely.

Using string as a temporary replacement for a broken shock cord

If the shock cord in your tent pole is damaged beyond repair and you don’t have a new replacement cord on hand, you can use a string to tie the poles together until you can purchase a new replacement cable. Although this will not have the same elastic characteristics as real shock cable, it can be used as a temporary replacement until you can make more serious repairs. Keep this in mind when using this. All you need to execute this DIY patch is a length of strong string and a hair bobby pin, making it a simple repair that can be completed with a small number of supplies.

Remember to be careful not to mix up the pole pieces once again, so that you can quickly put them back together thereafter when you’re through.
Calculate the length of your string based on the length of your tent pole plus a few additional inches for tying the knots, and then cut it.
This will make it much easier to thread the string back through the tent.
Dropping the bobby pin down through the pole and then gently pulling it out from the other side is a good way to do this.
Because you’re using string rather than an elastic cord, you won’t be able to tighten it before tying it off properly.
Tie off your string on the grommet peg, allowing for the additional length, and then singe the ends to avoid fraying.

When you’re finished, we recommend that you unfurl your poles to make sure there’s enough slack to pack away your tent properly. Any mistakes can be corrected by untying the end at a peg and making any required modifications.

How to repair a broken tent pole

The shock cord isn’t the only part of your tent pole that might break; the outer poles themselves can be susceptible to breaking at times. If you experience a tent pole breakdown while on a camping vacation, it might render your shelter entirely inoperable! You should be familiar with these simple methods for repairing a damaged tent pole as well as changing the bungee cord so that you are prepared for any situation that may arise. A pole repair sleeve, also known as a splint, is the most straightforward method of repairing a broken pole.

Purchasing a repair sleeve is a cheap option if your tent does not come equipped with one; you never know when you might require one.
If the tent pole has simply been twisted, and not completely cut, gently bend the metal back into place to prevent further damage.
If there are any shards of broken tent pole metal in your path, try bending them back inwards with some pliers or, if necessary, a rock to clear the route.
Alternatively, if you do not have a tent pole repair sleeve, you can splint the pole with an extra stake.
Using duct tape, secure a stake to either side of the broken tent pole and then line up the broken tent pole the same way you did previously.

Preventing damage to your tent poles in the future

If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.

When building your tent and connecting the tent poles, start with the central segment and work your way out from there.

This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.

You’ll be considerably more likely to prevent repairs and replacements in the future if you follow these few simple suggestions. If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.

Final Verdict:

It is occasionally required to replace the shock cord in your tent pole, but it does not have to be a difficult process. It is possible to save a large amount of money by making minor repairs and replacements to your camping equipment over time, and it is also considerably healthier for the environment. Learning how to execute these little repairs is simple, and more importantly, it will make you a more experienced camper. As an added bonus, watch this video for some further tent pole repair advice!

Video How To: Repair a Tent Pole

You don’t have to throw away your old tent poles since Matt from Next Adventure teaches us how to restore them to life by replacing a broken or worn shock cable. – Hello everyone, my name is Matt and I’d want to introduce myself. We’re here at the next adventure, and now we’re going to speak about how to fix the shock cord in your tent poles, which you may have damaged. Frequently, people bring in tent poles with the shock cable stretched out, and all that is required is to replace the shock cord where it passes through the middle of the pole.

Most high-end tent poles are constructed in such a way that the shock cord may be re-threaded when it becomes frayed.
Some of the lower-cost poles, particularly fiberglass poles, are not as durable as they should be.
The result is that each and every tent pole will be a little bit different.
Aluminum tent poles with an end cap that’s tacked in place or crimped in place using a little pinching mechanism are sometimes available.
Sometimes they just won’t come out, and you’ll have to be a bit creative with how you remove them, or you may decide not to remove them at all.
This man is quite easy, as you can see by the shock cord, which has been threaded through a small hole in the end cap and tied off with a knot at the other end.
It’s going to be nice and simple, and it’ll serve as a fantastic small example to demonstrate the fundamentals.

A tape measure is another a useful tool that can be carried around in a pocket.

If you have a shock cord that is the same length as your tent pole, you should be able to stay dry.

The length of your tent pole will be the first thing you’ll need to know while setting up your tent.

I like to extend the entire thing out and measure it as an one unit, and you’ll need around the same amount of shock cord as the precise measurement of your pole to complete the job.

While it is true that this guy is going to suffer a little, we also want a teeny-tiny amount of strain on him.

A large number of tent poles are divided into portions and have distinct sections and components of the pole.

As a result, we’re going to nu-thread every single one of these people.

My new shock cable has arrived, and I want to use it to shock this individual.

Make a small stopper knot to prevent the item from slipping through the hole.

There are a few various methods in which you can thread it through the hole.

You may feed this wire all the way through; as you can see on this one, we used the pliers to form a small hook on it before we started working with it.

It’s going to turn out perfectly.

Another option is to allow yourself as much slack as you need and simply rely on gravity to assist you in your endeavors if necessary.

In order to get the most out of that additional little amount of slack, feed it all the way into the pole.

We may now begin to feed the rest of the material through.

As a result, this will be sufficient.

Now, this is connected, and we will use it to feed back information into the poll.

That’s it, I’m done with you.

We at Next Adventure are not a repair business, but we strongly believe in the value of recycling and extending the life of your gear.

We aim to provide our customers the ability to fix their own equipment. Come come in and have a conversation with us about it. We want to look into options for you to continue to use the equipment you enjoy.

Amazon.com : MSR Tent Pole Repair Splint : Sports & Outdoors

5.0 stars out of 5 for this product What a lifesaver this is! On September 7, 2021, a review will be conducted in the United States. The item was bought in order to repair a tent that my children have enjoyed using. Their secure haven has served as a haven for them while Daddy has been in the hospital and receiving cancer treatments. An altercation culminated in the pushing of a twisted tent pole. It’s the ideal fit. This is the extra-large version. If I had the option, I would give it 6 stars!

Reviews with images

On July 5, 2020, the United States will conduct a review. Small in stature. Color: crimson Purchase that has been verified I’m certain that this will work because I borrowed one from a colleague. After that, I went out and bought my own, first measuring the pole extremely carefully, as recommended by another customer. Even so, the 13mm did not fit over my 3/8 inch hole “Because I measured the diameter of the shattered fiberglass rather than the diameter of the metal tubing that supports each part of fiberglass, I had to use poles.

The metal splint has to be placed over the metal tubes in order to be effective.
Don’t make the same mistake I did!
Size: Extra-large Color: dark ebony Purchase that has been verified The item was bought in order to repair a tent that my children have enjoyed using.
An altercation culminated in the pushing of a twisted tent pole.
This is the extra-large version.
5.0 stars out of 5 for this product What a lifesaver this is!
The item was bought in order to repair a tent that my children have enjoyed using.

An altercation culminated in the pushing of a twisted tent pole.

This is the extra-large version.

The photographs in this review On March 10, 2021, a review will be conducted in the United States.

Extremely stiff.

It is highly recommended that you bring some of these along with you on every camping excursion.

Color: BlackSize: Extra-Large Purchase that has been verified Using this, a damaged pole in a dome tent was repaired, and the repair lasted for the whole weekend.

It’s a fantastic, low-cost, and rapid solution!

Size: Extra-large Color: BlackPurchase that has been verified I needed to find a short piece of strong tubing that was exactly this size to replace a hub that had disintegrated and had 6 aluminum poles (1/2 inch diameter) “I cut three of these repair poles in half and plugged them into an outlet at the top of my tent, and it appears that they will do the trick.

I believe they would do admirably in the predicted capacity as well.
Size: SmallColor: RedPurchased with a verified credit card We won’t be able to take off without it.
On July 7, 2019, a review was conducted in the United States.
Exceptionally well-made and low in weight.
Size: SmallColor: RedVerified PurchaseReviewed in the United States on September 17, 2018Size: SmallColor: Red Even though I did not require the usage of this splint on my three-day backpacking trip in Utah’s High Uintas, I was pleased I had it with me before I departed for my trip.

Peace of mind is quite valuable, especially considering how lightweight and small this item is and how little room it takes up in your backpack or bag. Don’t forget to bring along some duct tape in case you need to use it later!

Top reviews from other countries

5.0 stars out of 5 for this product High-quality materials are used. On November 22, 2021, the United Kingdom will conduct a review. Size: SmallColor: RedPurchased with a verified credit card It’s a mending splint, so what can you say about it? It appears to be of high quality, but I haven’t had to put it to use yet, thank goodness. Excellent value for money. 5.0 stars out of 5 for this product As predicted, the MSR quality was excellent. On July 23, 2019, a review was conducted in the United Kingdom.

– 5.0 stars out of 5 for this product ゆるキャン△はいいぞ On April 29, 2020, the Japanese government will review the document.

Size: X-LargeColor: BlackProduct has been verified テントを試し張りしたとき、紐でしっかりと張らなかったので、強風でポールがポキリ。ポールに通すとスカスカだったので、ちゃんと使えるか心配でしたが、テントを張るとポールはしなるので、きちんと固定されました。２ヵ所折れてしまったので、それぞれに使用しましたが、全く問題なく過ごせました。念のため予備用も購入しました。 On December 16, 2019, a customer in Japan gave it a rating of 2.0 out of 5 stars(*).Size: SmallColor: RedVerified Purchase 急遽キャンプに行くことにしたのでプライムのお急ぎ便に対応したこちらを買いましたが高い。同じ用途の商品でもっと安いのたくさんあるので時間ある人はそういった商品を探したほうがいいです。

How do I repair a broken tent pole at home?

This page was last modified on Tuesday, March 9th, 2021 at 10:25 a.m. CRACK! When a pole cracks, we are all familiar with the heart-stopping sound. When a tent pole snaps, the structure of your tent is instantly damaged, making the remainder of your camping trip or next vacation a little more difficult to navigate. There isn’t a simple method to repair your tent pole at home, but there are several fast solutions that can splint the pole and get you through the rest of your adventure. Even if your pole is just bent or split in a few places, it is still vital to strengthen the weaker region.

If you are in a rush and want a more urgent remedy, continue reading!

Using a Tent Stake as a Splint

If you find yourself in the middle of nowhere and do not have a repair sleeve on hand, do not despair; you may still splint your pole! Materials:

Duct tape or any other adhesive and long-lasting tape is recommended. a stake for a tent

Instructions:

Even if the pole is just slightly bent, make every effort to straighten it out. Assuming the pole has been broken, make every effort to align the two fractured portions so that they are as flush as feasible. Assemble the tent stake by aligning its center with the center of the brake. Using tape, closely wrap the stake and pole together, ensuring sure that the stake is properly secured to the pole

Using a Pole Splint

Some modern tents come with helpful tent pole sleeves, which are simply shorter, hollow tubes of metal that can be slipped over your pole and used to strengthen broken or weakened areas of the structure. This is optional, but if your tent did not come with one, you may purchase one from your local gear shop and bring it with you on your next trip. The finest pole sleeves are slightly wider in diameter than your pole, allowing the inner broken pole to move about without being too much of a distraction.

Materials:

Tent pole repair sleeves
Duct tape or any other adhesive and sturdy tape
Tent pole repair sleeves

Instructions:

Even if the pole is just slightly bent, make every effort to straighten it out. Assuming the pole has been broken, make every effort to align the two fractured portions so that they are as flush as feasible. Continue to slide the repair sleeve over the broken section until it is roughly aligned with the center of the sleeve’s center. Wrap the two ends of the pole sleeve with tape to ensure that it is securely attached to the pole (be certain that the sleeve does not shift or move about)
And

How to Fix a Tent Pole

Documentation Download Documentation Download Documentation Breaking a tent pole might bring your camping vacation dreams crashing down around you, literally, if you’re not careful. That is, unless you know how to do a few simple repairs on your own.

A few simple, readily-available supplies will have you back in the warmth and safety of your dependable shelter in minutes, whether you’re tape up a pole that’s been split down the middle, strengthening a broken part, or replacing a worn out shock wire.

1 Place the damaged pole on a level place and allow it to air dry. This may be accomplished with the use of a portable camping table or picnic table. You may also place the pole on top of a flat piece of equipment, such as a cooler or a toolbox, if you don’t have access to either of these pieces of furniture. The worst-case situation may be solved by placing a smooth rock or a level stretch of ground on the ground.

There is no need to disassemble the pole or remove the elastic shock wire that binds it together
This is a simple procedure. Clean up any leaves, twigs, pine needles, sand or other similar material from your work surface before you continue. It is possible that if any of these materials make their way onto your tape, they will impair its ability to adhere correctly.

2 Cut a piece of gaffer’s tape the same length as the split part and place it over the split segment. To decide how long a strip of tape you will require, align the loose end of the tape with the extreme end of the segment, then gently unspool the roll until you reach the far end of the segment. Cleanly tear the tape to ensure that both ends are perfectly square

Gaffer’s tape is a sort of heavy-duty, high-strength tape that is widely used to repair electrical and mechanical components. It is also known as gaffer’s tape duct tape. You can pick up a roll of gaffer’s tape for a few dollars at any hardware shop or home improvement center
If you didn’t bring any gaffer’s tape with you, an ordinary roll of duct tape will enough
If you forgot to bring gaffer’s tape, an ordinary roll of duct tape would suffice

Tip: This simple, no-frills solution is best suited for emergency scenarios, such as when a pole splits on you while you’re already out in the woods. Advertisement
s3 Place the lateral edge of the tape over the split and press firmly into place. Cover the full length of the split with a strip of tape measuring 1 4–1 2inch (0.64–1.27 cm). Depending on the breadth of the roll you’re working with, you’ll have between 1 2 and 11 2 inches (1.3 and 3.8 cm) of reinforcement left over.

It is significantly more beneficial to tape a split longitudinally than than merely covering the ends of the split. The greater the amount of surface area on which the tape can attach, the more securely it will clamp the split together.

4 Continue wrapping the tape around the split until it is completely covered. Fold the tape with care to avoid leaving wrinkles or creases in the fabric. The pads of your fingers can be used to smooth down the strip after you’ve secured the entire strip in place. You are now free to continue erecting your tent without any additional concerns.

By wrapping the tape in this manner, you will be able to overlap the split itself at least twice while simultaneously tying the remainder of its length. It should be fine to go for the rest of the season, if not longer, if you use the proper type of tape and wrap your pole tightly.

1 If required, trim or break off the jagged edges surrounding the break to prevent it from fraying. Remove any shards or splinters that are visible extending out beyond the shaft of the segment with wire cutters, or pry them loose with a pair of pliers if they are stuck in the shaft of the segment. This will ensure that the afflicted area has a consistent thickness and that the rough edges do not cause more harm.

It’s possible that you’ll have to manually bend aluminum poles back into shape in order for them to fit inside the tent pole repair sleeves that you’ll be utilizing. A large number of aluminum tent poles can be bent by hand, but if you are having trouble, you may try using an arbor press in the same way that you would bend tiny aluminum sheet pieces.

It’s possible that you’ll have to bend aluminum poles back into shape by hand in order for them to fit inside the tent pole repair sleeves that you’re going to use. The majority of aluminum tent poles can be bent by hand
But, if you are having trouble, you may try using an arbor press in the same manner you would bend tiny aluminum sheet pieces.

Most modern tents come with at least one repair sleeve, which allows you to do quick repairs in the field. These are often constructed of an ultra-strong aluminum alloy, which results in a splint that is both durable and lightweight. Alternatively, if you don’t have a repair sleeve available, a tent pole or a stout stick might be used as a substitute.

Tip: Although it is not required to disassemble the pole in order to slide the sleeve into position, it may be more convenient to do so. 3 Duct or gaffer’s tape can be used to secure the ends of the sleeve. Strips of 4–6 in (10–15 cm) wide tape should be torn off the pole and wound around the spots on the pole where they emerge from the sleeve’s outer borders. After you’ve applied the tape, you’ll be free to set up and pack your tent as you usually would, safe in the knowledge that the splint will function to stabilize the fracture.

Feel free to wrap the tape around the sleeve as many times as necessary to be absolutely ensure that it remains in place. You may even go all the way around the sleeve if you want to
Despite the fact that the usual tent pole repair sleeve is durable enough to withstand numerous camping seasons, it’s a good idea to locate a new pole as soon as possible after the incident occurs.

First, look for an identically sized replacement section to use in place of the damaged pole. Some tent manufacturers include replacement parts with their products, such as poles and pole segments, in the initial packaging. It’s possible that your tent didn’t come with any replacement parts, in which case you’ll have to buy a new section from the original manufacturer. If you’re buying an old segment, make sure you measure it across the opening to ensure you’re obtaining one with the correct measurements.

You may also be able to locate a specific pole segment that meets your requirements on a website or via a merchant that specializes in old outdoor equipment. Replacement tent pole segments are often constructed considerably longer than conventional tent pole segments, allowing them to be readily trimmed to fit
However, replacement tent pole segments are not always made this way.

A website or company that specializes in old outdoor gear may also be able to help you locate a specific pole section that meets your specifications. Unlike conventional tent pole segments, replacement tent pole segments are often significantly longer than standard tent pole segments, allowing them to be readily trimmed to fit.

Alternatively, you can place a strip of contrasting masking or painter’s tape around the segment to indicate where you want to make your cut. If your poles are constructed of fiberglass, cutting through the tape rather than the exposed shaft may also assist to prevent cracking or splitting. Don’t worry about being too accurate here
The goal is to prevent cracking or splitting. Whatever the length of the new segment is relative to the length of the original section, it will perform perfectly.

3 Using a hacksaw, cut the section to the desired length. Orient the pole piece such that the portion bearing the mark you just produced extends beyond the edge of your work surface when you place it at the edge of your work surface. Then, using smooth strokes and steady, moderate pressure, glide the teeth of your hacksaw back and forth over the line. Continue to saw until you reach the end of the segment
This will take some time.

The opposing end of the section should be held securely in place with your free hand to prevent it from sliding around unexpectedly while you’re attempting to concentrate on sawing. When using your hacksaw, proceed with caution. Despite the fact that they are not very hazardous instruments, an accident might still occur if you are not paying attention to what you are doing.

Advice: If you don’t already have one, a small portable hacksaw might be a very helpful addition to your camping kit. 4 Smooth down the rough edges on the cut end of the new section with a file or sandpaper. Following the trimming of the piece to the proper length, all that is needed is to smooth out the new opening with a metal file or a sheet of medium-grit sandpaper to make it seem smooth. A gentle polishing will prevent the elastic shock cord that holds the pole together from fraying once a fresh cut has been made.

It is advisable to use sandpaper with a grit that is anywhere between 80 and 120 while doing this activity.

1 Remove the old cord from the pole by cutting the anchor knots at either end of the pole. Remove the knot from the pole by inserting a pair of needle-nose pliers into the open end of the pole. Cut the rope slightly below the knot with a sharp knife or a pair of scissors, and then wriggle it out of the jointed pole segments with your fingers.

When you pull the cable out, be cautious not to lose any of the loose pole pieces that may have come away. Because they’re cylindrical, they’ll be more prone to rolling than other shapes. Due to the fact that you will be dismantling the pole in order to install the new shock cord, now is a good time to replace any pole segments that are showing signs of wear.

Tip: Use a felt-tipped marker to number the pole parts, starting with the end that was cut first. Putting them all back together in the proper arrangement will be a piece of cake later on. 2 A knot on one end of the replacement cord will serve as an anchor for the replacement cord. Simply choose a point 4–6 inches (10–15 cm) away from the end of the string and loop it into a basic double overhand knot to complete the look. After that, give the knot a couple of strong tugs to make sure it’s secure

A steel washer can be placed on the segment of the rope where you intend to tie your knot if you so choose to do so. The spherical washer will provide something for the rope to bite into and will enhance the longevity of the completed knot, as well as its appearance. Putting a knot on one end of the rope before you start working it through the various segments that make up the pole will prevent it from accidently coming out.

3 Each of your pole segments should have a fresh cable threaded through it. Running the cord through each section one at a time and securing them all together is the quickest and most efficient method of accomplishing this. In most cases, when you purchase a replacement shock cable, it will come with an attachable wire pull-through mechanism, which will assist you in speeding up the procedure somewhat.

When pulling the cord through, it may be helpful to have an aide hold each piece for you while you concentrate on pushing the cord through.

4 Remove one end of the cord and tie it off with the pole stretched out to its full length. Once you’ve completed the process of running the new cord through each section, lay the entire assembly down on the floor. Extend the cord to generate some tension, then twist up a second double overhand knot 4–6 inches (10–15 cm) from one end of the cord opposite the one you began with. That is all there is to it.

Remember to put a second washer onto the string before tying your final knot if you used one on the first side
Otherwise, the knot will not hold. It is important to remember that if your shock cords are connected with metal pull tips rather than anchor knots, you must replace them according to the manufacturer’s specifications.

Things You’ll Need

Gaffer’s tape or duct tape for tent pole repair
A tent pole repair sleeve Wire cutters or pliers (as an alternative)
Optional: a tent stake or a stout stick (for use as a makeshift splint)

Toolkit includes: replacement pole segment
Felt-tipped marker
Hacksaw
Metal file or medium-grit sandpaper
Contrast tape (optional)
And instructions.

Sharp knife or scissors, steel washer (optional), replacement shock cable (optional), hacksaw (optional), and other miscellaneous supplies. Alternatives include: a file or sandpaper. Optional: a felt-tipped marker

About This Article

Thank you to all writers for contributing to this page, which has been viewed 8,616 times so far.

Did this article help you?

The absence of an elastic rope has no effect on the structural integrity of the tent. It is also simple to change, whether out on the field or once back at the house. All you have to do is get some elasticated cable. We include around 5m of 3mm diameter cable with our pole kits, but 2.5mm and 3mm diameter rope may be purchased online or through outdoor merchants as well. Remove the old rope and make a note of the sequence in which the poles should be reassembled before proceeding. While it is not necessary with an Outwell tent, you will discover that the pole sections of other types can sometimes differ, and you will also want to make sure that you have the correct end poles if you want to prevent having to rethread everything once you have finished.

Pass the opposite end of the cable through the pole.

In our pole replacement kits, we provide a narrow twisted gauge wire that is easy to work with.

Although we recommend that you tape the cable to the wire, it is simpler to slightly crimp the loop to guarantee that the wire and cord slide through the pole’s 4mm diameter hole with no difficulty.

Once it arrives at the conclusion of a segment, pull through.

As you finish each component, make sure you connect it to the threaded section that came before it.

Place the knot in the working end of the rope and insert it into the metal socket to complete the installation.

Here’s our best tip for keeping your tent and camping gear as clean as possible.

Ethan Fontole