How to Fix a Broken Tent Pole
There have been 58 reviews with an average rating of 3.7 stars out of 5 stars for this product. Tightly woven tent poles serve as the skeleton of your outdoor shelter, giving support and structure to keep the tent standing. If a pole breaks, your tent may wobble, flap, or fully collapse, therefore it’s a good idea to be prepared with the essential materials and know-how to repair a broken pole before you go camping. In this tutorial, we’ll show you how to do the following:
- While in the field, learn how to use a repair sleeve or an old tent stake to hold a broken tent pole together until it can be repaired at home. Learn how to replace the flexible shockcord inside your tent pole if it breaks or wears out and how to make an at-home repair.
Repairs by professionals: If you require expert assistance, many REI locations can do simple repairs. Alternatively, TentPole Technologies, the nation’s best pole repair service, is a fantastic alternative. REI Repair Services is a division of REI.
Splinting a Broken Tent Pole
The damage done to your tent pole by a violent gust of wind or stepping on it is irreversible. A kinked, split, or shattered pole requires rapid treatment when out camping (when you get home, you can look into having the pole replaced or professionally repaired.) There are two alternatives available to you:
- Use a pole repair sleeve to fix the problem. Make a splint out of a tent stake.
Using a Pole Repair Sleeve
A pole repair sleeve is the quickest and most convenient method of repairing a damaged pole. This little tube, which is also known as a splint, is frequently included with your tent. If you don’t already have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not move about too much. A repair sleeve is an easy way to patch a broken tent pole. Here’s how:
- A pole repair sleeve is the most convenient and time-saving method of repairing a damaged utility pole. Short tube that is commonly included with your tent, this item is also known as a splint or a splint tube. If you don’t have one, go out and get one. Pole repair sleeves should be somewhat bigger in diameter than the pole they are intended to fix so that they do not slide about excessively. In order to repair a broken tent pole, follow these simple instructions:
Using a Tent Stake as a Splint
A pole repair sleeve is the most convenient and time-saving method of repairing a damaged pole. This little tube, sometimes known as a splint, is frequently included with your tent. In that case, go out and get one and bring it with you. Pole repair sleeves should be just slightly bigger in diameter than your pole so that it does not slide about too much as you are working on it. It is simple to use a repair sleeve to repair a damaged tent pole:
- Stack the broken pole components in a straight line
- The curve should be straightened out if the pole is bent but not completely broken. Align the stake such that it is centered close to the breach in the ground
- Wrap duct tape around each end of the stake/pole many times, or use whatever heavy-duty tape you have on hand.
How to Replace Tent-Pole Shockcord
After a period of time, the flexible shockcord that is included within your tent poles may become abraded and snap, or it may just lose its elasticity completely. Despite the fact that the shockcord snaps while you’re out in the field, you may still utilize the pole by carefully assembling each of its component pieces. But when you arrive home, you’ll want to replace the shockcord since it simplifies the assembly process and prevents you from losing a pole segment during transport. Fortunately, the procedure of changing it is uncomplicated.
- After a period of time, the flexible shockcord that is included within your tent poles may become abraded and snap, or it may simply lose its elasticity altogether. If the shockcord cracks while you’re out in the field, you may still utilize the pole by carefully assembling the different portions of the pole as needed. But when you arrive home, you’ll want to replace the shockcord since it simplifies the assembly process and prevents you from losing a pole segment during transportation. However, it is a basic process to get it replaced. What you’ll require is as follows:
The following is the procedure for replacing the shockcord:
- Begin by placing the tent pole out straight on the ground. Sections can be labeled with a permanent marker (masking tape can be used if you don’t want to write directly on the pole) to prevent them from becoming mixed up. Remove the old cable by snipping it, and then take the elastic out of the pole end. Maintain the same sequence and alignment of all of the pole parts for the duration of your job
- It is common for tent poles to have a little metal piece attached at either end where the string is fastened
- Keep an eye out for these pieces and make sure they are not lost. Using your old shockcord, untangle the ends and place them next to your new shockcord. the length of the new piece of shockcord should be trimmed to match the length of the original The replacement part should be approximately 8 inches shorter than the previous section if the old shockcord has become stretched out and no longer has its elastic properties. Tighten one end of the shockcord and pass the other end through all of the pole sections until the last one
- Make a temporary knot in the shockcord to prevent it from slipping back into the second-to-last pole piece
- Alternatively, you may use a pair of locking pliers to secure the cord in place. Feed the remaining shockcord through the final part of the pole and tie the end together. Return to the beginning and untie (or unclamp) the rope that connects the final two pole parts. Check to make sure that all of the pole components are securely fastened to the completely completed pole. If the shockcord is still too slack, untie one end and pull it out 6 inches at a time until the poles are securely fastened together when the shockcord is tightened. It is important not to over-shorten the rope. Using pliers, remove the parts of the pole and fold it up starting at the center position
Related Articles
- Getting Started with Tent Care
- How to Repair a Tent
- Checklist for Backpacking Repair Kits
- How to Set Up a Tent
Contributing Experts
Getting Started with Tent Care; How to Repair a Tent; Checklist for Backpacking Repair Kits; How to Set Up a Tent & More
Laura Evenson
Instructions on how to care for a tent, how to repair a tent, Backpacking Repair Kit Checklis, and how to set up a tent
Chris Pottinger
Tent Care Fundamentals; How to Repair a Tent; Backpacking Repair Kit Checklis; How to Set Up a Tent
Lindsey Stone
Getting Started with Tent Care; How to Repair a Tent; Checklist for Backpacking Repair Kits; How to Set Up a Tent
How to Fix a Tent Pole
Documentation Download Documentation Download Documentation Breaking a tent pole might bring your camping vacation dreams crashing down around you, literally, if you’re not careful. That is, unless you know how to do a few simple repairs on your own. A few simple, readily-available supplies will have you back in the warmth and safety of your dependable shelter in minutes, whether you’re tape up a pole that’s been split down the middle, strengthening a broken part, or replacing a worn out shock wire.
- 1 Place the damaged pole on a level place and allow it to air dry. This may be accomplished with the use of a portable camping table or picnic table. You may also place the pole on top of a flat piece of equipment, such as a cooler or a toolbox, if you don’t have access to either of these pieces of furniture. The worst-case situation may be solved by placing a smooth rock or a level stretch of ground on the ground.
- There is no need to disassemble the pole or remove the elastic shock wire that binds it together
- This is a simple procedure. Clean up any leaves, twigs, pine needles, sand or other similar material from your work surface before you continue. It is possible that if any of these materials make their way onto your tape, they will impair its ability to adhere correctly.
- In order to remove the pole’s elastic shock cord, which binds it together, there is no need to disassemble it. Clean up any leaves, twigs, pine needles, sand or other debris from your work surface before continuing. It is possible that if any of these materials make their way onto your tape, they will interfere with its ability to adhere effectively.
- Gaffer’s tape is a sort of heavy-duty, high-strength tape that is widely used to repair electrical and mechanical components. It is also known as gaffer’s tape duct tape. You can pick up a roll of gaffer’s tape for a few dollars at any hardware shop or home improvement center
- If you didn’t bring any gaffer’s tape with you, an ordinary roll of duct tape will enough
- If you forgot to bring gaffer’s tape, an ordinary roll of duct tape would suffice
- Tip: This simple, no-frills solution is best suited for emergency scenarios, such as when a pole splits on you while you’re already out in the woods. Advertisement
- s3 Place the lateral edge of the tape over the split and press firmly into place. Cover the full length of the split with a strip of tape measuring 1 4–1 2inch (0.64–1.27 cm). Depending on the breadth of the roll you’re working with, you’ll have between 1 2 and 11 2 inches (1.3 and 3.8 cm) of reinforcement left over.
- It is significantly more beneficial to tape a split longitudinally than than merely covering the ends of the split. The greater the amount of surface area on which the tape can attach, the more securely it will clamp the split together.
- 4 Continue wrapping the tape around the divide until it is completely covered. Fold the tape with care to prevent leaving wrinkles or creases in the fabric. The pads of your fingers can be used to smooth down the strip once you’ve secured the entire strip in place. You are now free to continue erecting your tent without any further concerns.
- By wrapping the tape in this manner, you will be able to overlap the split itself at least twice while simultaneously tying the remainder of its length. It should be fine to go for the rest of the season, if not longer, if you use the proper type of tape and wrap your pole tightly.
- Using this method, you will overlap the split at least twice while simultaneously tying the remainder of the tape’s length together. If you apply the proper tape and wrap your pole tightly, it should last the rest of the season, if not longer.
- Using this method, you will overlap the split itself at least twice while simultaneously tying the remainder of the tape’s length together. If you apply the proper type of tape and wrap your pole tightly, it should last the rest of the season, if not longer.
- By wrapping the tape in this manner, you’ll be able to overlap the split itself at least twice while also binding the remainder of its length. If you apply the correct sort of tape and wrap your pole tightly, it should last the rest of the season, if not longer.
- By wrapping the tape in this manner, you will be able to overlap the split itself at least twice while simultaneously tying the remainder of its length. It should be fine to go for the rest of the season, if not longer, if you use the proper type of tape and wrap your pole tightly.
- Tip: Although it is not required to disassemble the pole in order to slide the sleeve into position, it may be more convenient to do so. 3 Duct or gaffer’s tape can be used to secure the ends of the sleeve. Strips of 4–6 in (10–15 cm) wide tape should be torn off the pole and wound around the spots on the pole where they emerge from the sleeve’s outer borders. After you’ve applied the tape, you’ll be free to set up and pack your tent as you usually would, safe in the knowledge that the splint will function to stabilize the fracture.
- Tip: While it is not required to disassemble the pole in order to slide the sleeve into position, doing so may be more convenient. 3 Duct or gaffer’s tape can be used to secure the sleeve’s ends together. Strips of 4–6 in (10–15 cm) wide tape should be torn off the pole and wound around the spots where they emerge from the sleeve’s outside edges. As soon as you’ve applied the tape, you’ll be free to set up or pack your tent as you normally would, certain that the splint will function to stabilize the fracture.
- First, look for an identically sized replacement section to use in place of the damaged pole. Some tent manufacturers include replacement parts with their products, such as poles and pole segments, in the initial packaging. It’s possible that your tent didn’t come with any replacement parts, in which case you’ll have to buy a new section from the original manufacturer. If you’re buying an old segment, make sure you measure it across the opening to ensure you’re obtaining one with the correct measurements.
- First, look for an identically sized replacement segment to use in place of the damaged pole piece. Poles and pole pieces, for example, are included in the packaging of certain tents manufactured by other companies. It is necessary to acquire a replacement section from the original manufacturer if your tent did not include any spare parts. It’s important to take a measurement across one of the old pieces to ensure that you’re obtaining one with the proper size.
- First, look for an identically sized replacement section to use in place of the damaged one. Some tent manufacturers include replacement components with their tents, such as poles and pole segments. If your tent didn’t come with any spare components, you’ll have to obtain a new section from the original manufacturer to complete the installation. It’s important to take a measurement across one of the old segments to ensure that you’re obtaining one with the correct size.
- 1 Locate a replacement section that is the same size as the damaged pole. Some tent manufacturers provide replacement parts in their product packaging, such as poles and pole segments. If your tent did not come with any replacement components, you will need to buy a new section from the original manufacturer. Make careful you measure across the entrance of one of the old parts to ensure you’re obtaining one with the proper proportions
- 3 Using a hacksaw, cut the section to the desired length. Orient the pole piece such that the portion bearing the mark you just produced extends beyond the edge of your work surface when you place it at the edge of your work surface. Then, using smooth strokes and steady, moderate pressure, glide the teeth of your hacksaw back and forth over the line. Continue to saw until you reach the end of the segment
- This will take some time.
- The opposing end of the section should be held securely in place with your free hand to prevent it from sliding around unexpectedly while you’re attempting to concentrate on sawing. When using your hacksaw, proceed with caution. Despite the fact that they are not very hazardous instruments, an accident might still occur if you are not paying attention to what you are doing.
- Advice: If you don’t already have one, a small portable hacksaw might be a very helpful addition to your camping kit. 4 Smooth down the rough edges on the cut end of the new section with a file or sandpaper. Following the trimming of the piece to the proper length, all that is needed is to smooth out the new opening with a metal file or a sheet of medium-grit sandpaper to make it seem smooth. A gentle polishing will prevent the elastic shock cord that holds the pole together from fraying once a fresh cut has been made.
- It is advisable to use sandpaper with a grit that is anywhere between 80 and 120 while doing this activity.
- This process will be best accomplished with a sandpaper with a grit ranging between 80 and 120.
- For this task, a sandpaper with a grit ranging between 80 and 120 will be most effective.
- Tip: Use a felt-tipped marker to number the pole parts, starting with the end that was cut first. Putting them all back together in the proper arrangement will be a piece of cake later on. 2 A knot on one end of the replacement cord will serve as an anchor for the replacement cord. Simply choose a point 4–6 inches (10–15 cm) away from the end of the string and loop it into a basic double overhand knot to complete the look. After that, give the knot a couple of strong tugs to make sure it’s secure
- Tip: Use a felt-tipped marker to number the pole parts, starting with the end that was chopped off earlier. This will make it much easier to put them all back together in the proper arrangement later on
- And 2 A knot on one end of the replacement cable will serve as an anchor for the new cord. Simply choose a point 4–6 inches (10–15 cm) away from the end of the cord and loop it into a basic double overhand knot to complete the design. Make a few of vigorous tugs on the knot to ensure that it is securely tied
- Tip: Use a felt-tipped marker to number the pole parts, starting with the end that was chopped. This will make it much easier to reassemble everything in the proper arrangement later on. 2 Make a knot at one end of the new rope to use as an anchor. Simply choose a spot 4–6 inches (10–15 cm) away from the end of the cord and loop it into a basic double overhand knot at that location. After that, give the knot a couple of strong tugs to make sure it’s secure.
- Tip: Use a felt-tipped marker to number the pole parts, starting with the end you cut. This will make it much easier to put them all back together in the proper arrangement later on. 2 Make a knot at one end of the replacement rope to use as an anchor. There’s no need to get fancy—just choose a spot 4–6 inches (10–15 cm) from the end of the rope and loop it into a basic double overhand knot. After that, give the knot a couple of strong tugs to ensure that it is secure
- Tip: Use a felt-tipped marker to number the pole parts, starting with the end that was cut first. Putting them all back together in the proper arrangement will be a piece of cake later on. 2 A knot on one end of the replacement cord will serve as an anchor for the replacement cord. Simply choose a point 4–6 inches (10–15 cm) away from the end of the string and loop it into a basic double overhand knot to complete the look. After that, give the knot a couple of strong tugs to make sure it’s secure
- Remember to put a second washer onto the string before tying your final knot if you used one on the first side
- Otherwise, the knot will not hold. It is important to remember that if your shock cords are connected with metal pull tips rather than anchor knots, you must replace them according to the manufacturer’s specifications.
Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement
- To obtain a new pole for your tent while it is still under warranty, get in touch with the manufacturer. Depending on the circumstances, they may even replace the entire tent for a minimal fee. It will be necessary to reshape steel tent poles by a qualified metal craftsman, albeit it may be more cost-effective in the long run to simply purchase a new set of poles. When looking for spare parts for popular tent types, online purchasing platforms such as eBay may be quite beneficial.
Thank you for submitting a suggestion for consideration! Advertisement
Things You’ll Need
- Gaffer’s tape or duct tape for tent pole repair
- A tent pole repair sleeve Wire cutters or pliers (as an alternative)
- Optional: a tent stake or a stout stick (for use as a makeshift splint)
- Gaffer’s tape or duct tape for repairing the tent pole pliers or wire cutters (as an alternative)
- For a DIY splint, a tent stake or robust pole might be used instead.
- Sharp knife or scissors, steel washer (optional), replacement shock cable (optional), hacksaw (optional), and other miscellaneous supplies. Alternatives include: a file or sandpaper. Optional: a felt-tipped marker
About This Article
Thank you to all writers for contributing to this page, which has been viewed 8,508 times so far.
Did this article help you?
Hey, hey, summer has officially here. Yes, the pandemic implies that some people may be unable to go or camp due to the disease, and many campgrounds will remain closed. However, scattered camping is still an option almost everywhere, and new campsites are being built all the time to accommodate the growing demand. To put it another way, it’s time to break out the tent. Alternatively, if one of the tent poles becomes damaged while being removed from the tent, it is necessary to utilize the little metal sleeve that came with the tent.
I’ve been camping for several decades and had never needed to use one before then.
It took me a while to figure out how the repair sleeve worked because I’d never used one before.
In this little video from MSR, the manufacturer of the Hubba Hubba NX, which is one of my all-time favorite hiking tents, you can see how simple it is to do that repair in the field.
How to Repair Tent Pole Elastic Cord (Re-thread) – the Easy Way
Determine the diameter of the cord that has to be replaced. When it comes to low-cost tents, this will often be approximately 2mm in diameter, which is not particularly sturdy or long-lasting. Depending on how large the opening diameter is of the pole, you may be able to utilize a thicker diameter than you originally planned. I increased the diameter of the cable on my tent poles from the standard 2mm to 3mm. The cable may be purchased on eBay for a reasonable price. I live in the United Kingdom and purchased 10 meters for around £3.
In order to set up a two-person dome type tent with two tent poles, you’ll need at least ten meters of space.
In an updated version of this post, I measured the original cable and discovered that it was half the length of the poles after they were completed.
As a general estimate, you could acquire a new cable that was 75 percent the length of the constructed poles, depending on the amount of elastic stretch in the existing cord.
Step 2: Find Your Threader
When it comes to cord replacement, determine the diameter of the cord. This will often be roughly 2mm in diameter on low-cost tents, making it not particularly sturdy or long-lasting. The aperture diameter of the pole may be larger than the diameter of the pole if you take measurements. I used a 3mm diameter rope for my tent poles instead of the standard 2mm. The cable may be obtained on eBay. The price of 10 meters was around £3 in the United Kingdom. The new cord (3mm) appears black in the photographs, whereas a worn-out, white cord with blue and red stripes is shown.
You will need to measure the constructed pole lengths for any tent larger than a two-man dome and purchase the appropriate length.
(See update below.) Based on the amount of elastic stretch in your cable, you could acquire a new cord that was 75 percent the length of the constructed poles, as a general estimate of the length of the poles.
Step 3: Join Threader to New Cord
Identify the diameter of the cord that has to be replaced. On low-cost tents, this will often be roughly 2mm in diameter, making it not particularly sturdy or long-lasting. Depending on how large the opening diameter is of the pole, you may be able to utilize a thicker diameter. I used a 3mm diameter cable for my tent poles rather than the standard 2mm. The cable may be purchased on eBay. I live in the United Kingdom and purchased ten meters for around £3. Please keep in mind that the new cable (3mm) is shown in black in the photographs, whilst the worn old cord (white with blue and red) is shown in white.
For any tent larger than a two-man dome, you will need to measure the completed pole lengths and purchase the appropriate length.
For example, if your cable has a lot of elastic stretch, you might buy a new cord that was 75 percent the length of your constructed poles as a rough estimate.
Step 4: Remove Old Elastic Cord and Re-thread New Cord
Determine the diameter of the cord to be replaced. On low-cost tents, this will often be roughly 2mm in diameter, which is not particularly sturdy or long-lasting. If you measure the opening diameter of the pole, you may discover that you may utilize a thicker diameter. On my tent poles, I chose a 3mm diameter cable above the original 2mm diameter rope. You may purchase the cable on eBay. I live in the United Kingdom and purchased 10 meters for roughly £3. Please keep in mind that the new cable (3mm) is shown in black in the photographs, while the worn old cord (white with blue and red) is shown in white.
For any tent larger than a two-person dome, you will need to measure the completed pole lengths and purchase the appropriate length.
Update: I recently measured the original cable and discovered that it was half the length of the poles when they were constructed. As a general estimate, depending on the amount of elastic stretch in your cable, you could purchase a new cord that was 75 percent the length of the constructed poles.
Step 5: Tension Cord and Tie Off the Ends
Trial and error is required to achieve the desired tension, so after threading the entire pole, experiment with your cord tension. The tension must be light enough to allow the poles to be pulled apart, yet firm enough to keep them together when threaded through the tent’s opening. The figure of eight knot is my preferred method of tying off the ends because it is a bigger knot that is also easy to alter. A more substantial knot at the end will last longer. You can then cut the cord after the tension has been reached to your satisfaction.
Step 6: Finished – Store Threader for Next Repair
You should have completed the repair of the tent poles by now. Remember to have your threader handy for when you need to repair your tent! I hope you have found this information beneficial. Thank you for taking the time to watch!
Be the First to Share
You should have completed the repair of the tent poles at this point. Remember to have your threader on hand for when you need to repair your next tent. I hope you have found this information to be of assistance. Please accept my thanks for your time.
Fixing a bent tent peg
You should have now completed the repair of the tent poles. Keep your threader handy for when you need to repair your tent. I hope you have found this information to be beneficial. Thank you for your time!
Replacing a snapped guy line
Guy lines are generally rather robust, and I haven’t come across one that has snapped yet. However, if this does happen to you, don’t be concerned, because replacement guy lines are readily available online.
Fixing Leaking Tent Seams
Guy lines are generally rather robust, and I haven’t come across one that has broken yet. However, if this does happen to you, don’t be concerned, because replacement guy lines are readily available online and in most sporting goods stores.
- The waterproof coating or seam sealant has become ineffective
- The seam has been stretched beyond its breaking point, and the seal has been compromised. A previously undiscovered fault has just recently become a problem as a result of a change in wind/rain strength and direction.
You should also double-check that the seam is indeed leaking, as moisture in a tent may often give the appearance of a leak. You could even find yourself with a pool of water in your tent if your tent hasn’t been properly ventilated before you set up camp. An additional consideration is that certain poly-cotton or canvas tents may have somewhat leaky seams the first time they are used, since the materialstitching has not yet settled (well, this is what one manufacturer reported anyway). It is simple to repair a little leaky seam.
If you want a more permanent solution, you may acquire some tent seam sealer instead.
Click here to read an article on how to avoid a leaky tent and how to stop the tent seams from leaking.
Waterproofing Your Tent
You should also carefully verify that the seam is indeed leaking, as moisture in a tent may often give the appearance of a leak. You could even find yourself with a pool of water in your tent if your tent hasn’t been properly ventilated. Additionally, some poly-cotton or canvas tents may have somewhat leaky seams the first time they are used because the materialstitching has not had time to settle properly (well, this is what one manufacturer reported anyway). It is simple to repair a little leaky seam.
Alternatively, tent seam sealer may be used for a more permanent solution. Once it has dried, you may apply the sealant. Click here to read an article on how to avoid a leaky tent and how to stop the tent seams from leaking:
Fixing a Bent or Broken Tent Pole
Now, the answer to a broken or bent tent pole is highly dependent on the type of tent pole in question, as well as the location and severity of the damage.
Replacing ‘bendy’ Fibreglass Tent Poles
If your tent is equipped with flexible tent poles (which are normally constructed of fiberglass or a composite material and are typically black or grey in color), they are the easiest to repair and replace.
1. Simple DIY Tent Pole ‘gaffa’ Repair
Most of the time, these sorts of poles are capable of splitting, exposing the inner elastic that binds the various pieces together. The best in-field fix for this is a simple piece of gaffa or duct tape. We’ve done this previously, and the tape really lasted for a few more seasons after that. When you go camping, always remember to bring some gaffer tape with you.
2. DIY Replacement Section
Most of the time, these sorts of poles may be split open, revealing the inner elastic that binds the various portions together. Regular gaffa/duct tape works well in this situation for in-field repairs. Before, we had done something similar, and the tape really lasted for a few of seasons after that. ” When you go camping, always remember to bring some gaffer tape.
Replacing Steel Tent Poles
It is possible to straighten a bent steel tent pole if it is a straight portion and it has not been bent too far out of shape; however, this is not recommended. But if that isn’t possible or if the tent pole is formed, it is preferable to take it to a metal craftsman with a non-bent pole that is identical to the bent pole. The metal worker will be equipped with equipment that will allow him to quickly return the pole to its original shape, as well as the ability to heat the pole if necessary to avoid straining the metal.
2. Replacing the bent pole section
It is possible to straighten a bent steel tent pole if it is a straight portion and it has not been twisted too far out of shape. But if it isn’t possible or if the tent pole is shaped, it is preferable to take it to a metal worker with another pole that isn’t bent. In order to minimize straining the metal, the metal worker will be equipped with equipment that will quickly restore it to its original shape. If required, the metal worker will heat the pole to restore it to its original shape.
3. Contact the retailer
It is possible to straighten a bent steel tent pole if it is a straight portion and it is not twisted too much out of shape. However, if this is not possible or if the tent pole is a shaped tent pole, it is preferable to take it to a metal worker with a similar non-bent pole in tow. The metal worker will be equipped with equipment that will allow him to quickly return it to its original shape, as well as the ability to heat the pole if necessary to avoid straining the metal.
4. Contact a spares supplier
Tent spares are only available from a few providers that offer a repair service. One such service isTentSpares.co.uk, a specialised outdoor repair service such asScottish Mountain Gear, which is one example of this type of service. My own experience with their service is limited (thank goodness! ), but I am aware of a few other people who have had positive experiences with it.
5. Contact the Manufacturer
Tent spares are only available from a few providers that offer a service. One such firm isTentSpares.co.uk, a specialised outdoor repair service such asScottish Mountain Gear, which provides tent spares and other outdoor equipment.
My personal experience with their service (touch wood!) has been positive, but I am aware of a few others who have had negative experiences with it.
6. E-Bay
For popular tent models, there is a considerable second-hand market to choose from. While the expense of purchasing a second-hand version of your tent for the purpose of replacing a pole may seem extravagant, it may still be less expensive than other alternatives. Keep an eye out on the second-hand market for any more tents that may be available as spares. Somebody else’s tent may have been damaged, but it may have been in a different place, and you will be able to pick it up for a far lower price.
Repairing a Ripped Tent
A considerable second-hand market may be available for popular tent types. While the expense of purchasing a second-hand version of your tent for the purpose of replacing a pole may seem exorbitant, it may still be less expensive than other alternatives if you shop about. Watch the second-hand market, though, for additional tents that may be sold as spares. Somebody else’s tent may have been damaged, but it may have been in a different place, and you will be able to pick it up for a far lower price.
Useful items for DIY Tent Repairs
Here are some tools and supplies you may use to repair your damaged tent on your own. GorillaTapeIdeal for making quick repairs in an emergency. Outwell The Luminous Guy Line is a line of clothing that is brightly colored and stands out from the crowd. VangoGuy Line is a transportation company that specializes on vangos. There are a variety of colors to choose from. OutwellDurawrap These are available in a variety of sizes. Outwell Steel Pole with a Straight Base These are available in a variety of sizes.
- VangoFibreglass Pole is made of fiberglass.
- McNettSeamSure For the purpose of repairing leaky seams McNettSeamgrip It is used for mending seams that have fallen apart.
- Patches of McNett’s tenaciousness For bigger holes in your tent, use a tent sealant.
- NikwaxTent It is possible to purchase them in either spray-on or bigger sizes.
- Photos courtesy of Thomas Guest.
Get the Family Camping Planner
You will receive the family camping planner once you have entered your name and email address.
Amazon.com : tent pole repair sleeve
THE RESULTSPrice and other information may differ depending on the product size and color selected. SponsoredSponsored This advertisement is being displayed to you because the product is relevant to your search query. Please provide comments on the advertisement.
TRIWONDER Tent Pole Repair Splint Repair Kit Spare Repair Tube for Diameter 7.9-8.5mm
Price and other specifications may differ depending on the product size and color.
SponsoredSponsored This advertising campaign is being displayed to you as a result of a product’s relevancy to your search query. Describe your experience with the advertisement.
KOMCLUB Adjustable Tarp Poles Camping Tent Poles Stainless Steel Lightweight Tent Poles for Trap Sun Sails Canopy Awning Shelter Backpacking Hiking 78 in Set of 2
Price and other specifications may differ depending on the product size and color. SponsoredSponsored This ad is being displayed to you because the product is relevant to your search query. Please provide comments on this advertisement.
GEAR AID Tent Pole Splint, Replacement Part
4.4 stars out of 5 for this product Ships to the Netherlands for 88$8.99
MSR Tent Pole Repair Splint
Rated 4.4 stars on the basis of 5 reviews Ships to the Netherlands for 88$8.99USD
TRIWONDER Tent Pole Repair Splint Repair Kit Spare Repair Tube for Diameter 7.9-8.5mm
4.2 stars out of 5 for this product 300 Ships to the Netherlands for $6.99 Debug information has been copied. Sketch was used to create this design. Sponsored
Green Elephant Telescoping Tarp Poles | Adjustable Tent Poles for Tarp Set of 2 | PortableLightweight Aluminum Tent Poles Replacement
4.6 stars out of 5 for this product 1,819$54.99 Get it as soon as Thursday, February 10 for $19.98 shipping EVEN BETTER RESULTS
Azarxis Tent Pole Repair Splint Repair Kit Spare Repair Emergency Tube for Diameter 7.9-8.5mm Tent Pole
the average rating is 4.6 out of 5 1,819$54.99 Take advantage of this deal as soon asThu, Feb 10 for just $19.98 shipping ADVANCED OUTCOME
T Tulead 10PCS Tent Pole Repair Sleeve Tent Pole End Plug Aluminum Alloy Spare End Plugs for 8.5mm/0.33″ Tent Poles
4.9 stars out of 5 for this product Shipping to the Netherlands is $8.99.
Zerone Tent Pole Repair Splint Tube Kit, 4Pcs Aluminium Alloy Spare Repair Tube for Diameter 7.9-8.5mm Tent Pole
4.9 stars out of 5 for this product. The shipping cost to the Netherlands is $20$8.99.
GEAR AID Tenacious Tape Fabric and Vinyl Outdoor Camping Gear Repair Tape, 3” x 20”
4.9 out of 5 stars for this product Ships to the Netherlands for $8.99.
Coghlan’s Tent Pole Repair Kit
4.4 stars out of 5 for this product 1,017 $4.64 Ships to the Netherlands are available. More Purchasing Options $2.99 (plus tax) (11 new offers) SponsoredSponsored This advertisement is being displayed to you because the product is relevant to your search query. Please provide comments on the advertisement.
MMoon-L F Adjustable Tent Tarp Canopy Pole Set of 1 for Camping Shelters and Awnings 6 Sections 7.6 feet Height Black Surface Durable Steel Rod
3.8 stars out of 5 for this product Ships to the Netherlands for $59$16.99
BRILLIANCE4U Aluminum Tent Poles Replacement, Fits Both Female and Male Ends, Lightweight Tent Pole Repair Kit, 7001 Series Aluminum Alloy T6 Heated
809 people rated this product 4.4 out of 5 stars $29.98 Ships to the Netherlands are available. More Purchasing Options $26.98 CAD (2 usednew offers)
BRILLIANCE4U Aluminum Tent Poles Male End Tips Replacement Accessories Spare End Plugs for 7.9mm, 8.5mm, 9.5mm Tent Poles
4.7 stars out of 5 for this product Ships to the Netherlands for 41$8.99
Coghlan’s Fiberglass Tent Pole Repair Kit
4.1 stars out of 5 for this product 537 $15.24 Ships to the Netherlands are available. More Purchasing Options $6.70 is the price of the item (8 new offers)
Coghlan’s Nylon Tent Repair Kit
4.1 stars out of five for this product. 537 $15.24 Netherlands is a destination for shipments There are more options for purchasing Six dollars and seventy cents (8 new offers)
Azarxis Tent Pole Repair Splint Repair Kit Spare Repair Emergency Tube for Diameter 7.9-8.5mm Tent Pole
4.1 stars out of 5 for this product Ships to the Netherlands for 108$6.99
BRILLIANCE4U Tent Pole Shock Cord 1/8 inch 60ft, Elastic Bungee Cord, Replacement Shock Cord for Tent Poles, Tent Pole Repair Kit, Durable Elastic Cord with Lead Wire and Washers
4.1 stars out of five for this product. Ships to the Netherlands for 108$6.99USD.
BRILLIANCE4U Tent Pole Repair Sleeve, Tent Pole Splint, Spare Repair Tube
4.1 stars out of 5 for this product. Ships to Netherlands for 108$6.99
BRILLIANCE4U Tent PinRing Replacement, Tent Pole Connectors, Aluminum Tent Pole Rings, Tent Building Tool, Tent Pole Accessories 5 Pack
4.1 out of 5 stars 108$6.99Shipping to the Netherlands
Coleman Replacement Tent Pole Kit
4.1 stars out of 5 for this product Ships to the Netherlands for 108$6.99
Mavelovs Tent Poles Replacement, Male Female End Poles Compatible, Lightweight Aluminum Alloy 7001 T6 Heated Tent Pole, Tent Pole Repair Kit Outer Dia. 0.33” 8.5mm 14 feet 7in
4.3 stars out of 5 for this product 32 $15.98 Ships to the Netherlands are available. SponsoredSponsored This advertisement is being displayed to you because the product is relevant to your search query. Please provide comments on the advertisement.
VICASKY 4 Pcs Tent Accessory Folding Joint Camping Supplies Plastic Support Rod Repair Support Rod Joint Parts Automatic Tent Support Components
Rated 4.3 stars on the basis of 5 reviews 32 $15.98 Netherlands is a destination for shipments SponsoredSponsored This advertising campaign is being displayed to you as a result of a product’s relevancy to your search query. Describe your experience with the advertisement.
NEED HELP?
4.3 stars out of 5 for this product.
32 $15.98 Shipments to the Netherlands SponsoredSponsored This ad is being displayed to you because the product is relevant to your search query. Please provide comments on this advertisement.
How do I repair the shock cord at the center of my pole?
4.3 out of 5 stars 32 $15.98 Ships to the Netherlands SponsoredSponsored You’re seeing this ad because the product is relevant to your search query. Provide feedback on the advertisement
DIY Shock Cord Replacement
4.3 stars out of 5 for this product 32 $15.98 Ships to the Netherlands are available. SponsoredSponsored This advertisement is being displayed to you because the product is relevant to your search query. Please provide comments on the advertisement.
- Rated 4.3 stars on the basis of 5 reviews 32 $15.98 Netherlands is a destination for shipments SponsoredSponsored This advertising campaign is being displayed to you as a result of a product’s relevancy to your search query. Describe your experience with the advertisement.
Did you find it helpful? Here’s a link to a wonderful tutorial from REI that goes over the process of fixing tent poles and includes a part dedicated to restringing shock cord at the base:How to Fix a Tent Pole Send input if you agree or disagree.
How to Replace Shock Cord in Tent Pole
Did you find it helpful? Here’s a link to a wonderful tutorial from REI that goes over the process of fixing tent poles and includes a part on how to restring shock cord at the base:How to Fix a Tent Pole Submit input if you agree or disagree
What is a tent shock cord and why is it important?
Here is a link to a wonderful tutorial from REI that goes into detail about fixing tent poles and includes a part dedicated to restringing shock cord at the base:How to Fix a Tent PoleDid you find it helpful? YesNoPlease provide input.
What you need to replace the shock cord in a tent pole
Here’s a link to a wonderful tutorial from REI that goes into detail about fixing tent poles and includes a part dedicated to restringing shock cord at the base:How to Fix a Tent PoleDid you find it helpful? Send feedback if you agree to it.
- The use of a shock cable (size 18″ or smaller) with adequate length to cover all of the poles that need to be fixed
- Scissors or a sharp edge
- Measuring tape
- Sharpie or marker pen
- A lighter or matches to melt the ends of the wires Tape for masking
How to replace a faulty shock cord in a tent pole
With enough length to cover all of your poles that need to be fixed, use a shock cord (size 18″ or less). Scissors or a sharp edge; measuring tape; Sharpie or marker pen; a lighter or matches to melt the ends of the wires; A masking tape is anything that is used to conceal something.
How to Repair a Shock Cord if it Breaks in the Field
A snapped or overstretched shock cable might make erecting your shelter more difficult if you’re already out on the trail during your camping vacation. If you want to repair the wire without having to replace the entire length, fortunately, there is a simple solution. However, while this is not a permanent solution, it will allow you to use your tent for a short period of time until you can replace the cord completely. If the cable hasn’t snapped, but rather has become too stretched out to go around your tent pole, there’s a simple solution.
Then, draw the shock cable through the grommet peg until it is taught once again, and reattach it to the grommet peg.
If the shock cord on your old tent pole has snapped, you’ll need to remove the pole using the steps outlined above to fix the problem.
Remove a few inches of the cord’s elastic core on each side of the break, leaving only the braided sheath on the other side.
The reason you need a thinner segment of cord to tie the knot is so that the knot will not become trapped in the poles and will be able to flow through freely. If you have a bent or damaged tent pole, it is simple to repair it no matter where you are.
Using string as a temporary replacement for a broken shock cord
A snapped or overstretched shock cable might make erecting your shelter difficult if you’re already out on the trail during your camping excursion. If you wish to repair the cord without having to replace the entire length, there is a simple workaround. However, while this is not a permanent solution, it will allow you to use your tent for a bit longer before replacing the cord. A simple solution exists if the cable has not snapped, but has instead become too stretched out to fit around your tent pole.
- Retie it at one end of the shock cord with a grommet peg after you have pulled it through until it is taught again.
- You’ll need to disassemble your old tent pole shock cord if the cable has snapped.
- Following the discovery of the cord’s snag, you’ll need to thin the material to prevent it from fraying.
- This thinner piece of rope should be tied into a secure knot, then the excess should be trimmed and singed to prevent fraying from occurring.
- No matter where you are, you can quickly repair a bent or damaged tent pole.
How to repair a broken tent pole
If you’re already out on a camping trip and you’re hit by a snapped or overstretched shock cable, putting your tent together may be tough. If you want to repair the wire without having to replace the entire length, there is a simple solution. This isn’t a long-term solution like replacing the cord, but it will keep your tent operating for a short period of time. If the cable hasn’t snapped, but rather has become too long for your tent pole, there’s a simple solution. Simply remove the peg from one end of your poles and untie the string from the other end.
Although the cable may not be as elastic as it once was, reducing the slack will allow the poles to perform more efficiently.
Once you’ve determined where the break is in the cable, you’ll need to thin down the material around it.
Tie a tight knot in this narrower section of cord, then cut and singe the excess to avoid fraying.
A thinner segment of cord is needed to tie the knot so that it does not become trapped in the poles and can still be passed through smoothly. No matter where you are, a bent or damaged tent pole may be simply repaired.
Preventing damage to your tent poles in the future
If you’ve had to make a repair to your tent pole shock cord and want to prevent having to do it again in the future, we have some suggestions for maintaining and extending the life of your tent poles to help you out. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment with loose soil, gravel, or mud. Openings into the hollow inside of the poles may be seen when your poles are folded up. It’s ideal to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and eventually break.
When building your tent and connecting the tent poles, start with the central segment and work your way out from there.
This will lower the amount of strain placed on the elastic shock cable within, hence reducing the likelihood of breakages and the need for replacement.
If you’re willing to put in the effort to make a few minor repairs, then resting on your camping vacation will be much more enjoyable.
Final Verdict:
For those of you who have had to make a repair to a tent pole shock cord and would like to prevent having to do so again in the future, we have some suggestions for maintaining and extending the life of your tent poles. Keep your poles off the ground at all times, especially if you’re working in a sloppy environment like loose soil, gravel, or mud. When your poles are folded up, there are apertures into the empty interior that you may see through them. It’s important to prevent having any debris get trapped inside your tent poles because this might cause the shock cord to become abrasive and break again.
When assembling your tent and connecting the tent poles, start with the central piece and work your way outwards from that point.
Thus, the elastic shock cable within will be put under less strain, which will lessen the likelihood of breakages and replacements being necessary.
If you’re willing to put in the effort to make a few minor repairs, resting on your camping trip will be much more enjoyable.
