How To Lift Roof Top Tent

Installing a Roof Top Tent – Solo!

If you own a roof top tent, you’ve probably looked at it and thought to yourself, “Can I put this on myself?” However, with weights ranging from 121 pounds (55kg) to upwards of 176 pounds (80kg), they are difficult to “lift” and install on one’s own without causing back pain. Installation is a nerve-wracking experience due to the weight, size, and height of your vehicle involved in setting up the tent. Yes, it is possible to erect a roof top tent on your own. Using a hoist is the most straightforward method of erecting a roof top tent on your own.

Now, that is a very simplistic version of how to erect a rooftop tent on your own, and the rest of this post will go into much deeper depth about the subject.

How much does a roof top tent weigh?

Roof top tents (soft shell) are quite light in weight, at 121 pounds (55kg) on average. The foundation, canvas, PVC cover, and ladder are all included with this price. The canvas, which accounts for the majority of the weight, was coupled with all of the metal interior components to give it more stiffness. Because their exterior shells are composed of aluminum or heavy-duty plastic, hard shell roof top tents will weigh significantly more than their soft shell counterparts. These can weigh as much as 200 pounds (100 kilograms) or more.

How to put on a roof top tent by yourself

Installing a roof top tent by yourself may be accomplished in three ways: using an ahoist, sliding tracks, or totally by yourself without the need of any equipment at all. The fact that it is so heavy might make it difficult to carry it securely on your own without the use of tools or other people’s assistance. We will, however, look at a variety of strategies that can help you get out of a jam if you are in a bind.

Hoist

With the use of a hoist, you can mount a roof top tent on your own without putting yourself or others in danger. A hoist is a pulley system that is mounted on a roof, generally in your garage. It is used to lift heavy objects. Because of its innovative design, it allows you to safely lift and load weight while the roof (or other supporting structure) bears the weight on your shoulders.

1. In order to properly position the tent under the hoist, heavy-duty straps must be wrapped tightly. As you raise the tent, make sure there is adequate room for the car. Placing the car below the tent is a good idea. Reduce the height of the tent and fasten the mounting components.

If you want to add and remove the roof top tent on a regular basis, this is the quickest and most convenient choice, and it is well worth the additional installation time. You may read the entire story by clicking here. Straps must be used to connect the roof top tent to the ground so that the weight is distributed evenly. If the weight distribution is not even, the tent may begin to slip or rock side to side in the air as a result of the unequal weight distribution.

It’s also vital to know that certain hoist systems require electrical power to function properly. Although there are certain goods that are propelled by muscle and physics, such as aRacor Ceiling Storage Heavy Liftor aLift and Lock, there are others that are not.

Tracks

Tracks are an inclined plane that provides an advantage to the user in relation to the amount of force applied. Tracks are a type of ramp that is used to raise the tent and place it on the roof of the vehicle’s roof. Without the use of a hoist, it is necessary to physically push the tent up the hill and into position on the vehicle’s roof.

1. Place the tracks on the roof rack (from either the back or the side of the car) and secure them. Tracks should be secured to both the ground and the ceiling (otherwise, the weight and pressing may cause them to come loose)
2. Push the roof top tent up the rails as far as it will go. Once you’ve reached the edge, you may either push over the top onto the roof racks or swivel the racks so that they are parallel with the car roof and continue to push from that position. Install the roof top tent in a safe and secure manner.

However, if your tracks are not firm and solid enough, this strategy may prove to be a bit risky. You’ll find it more simpler and safer to walk down a gradual slope rather than a severe incline. See mmaattppoohere’s forum post for further information. When there is a lack of available roof space and a hoist cannot be fitted precisely, it is possible to combine the track and hoist systems. Although you will still need to arrange the tent on the tracks, the hoist will assist you in lifting the track into the air (step 4).

They can be really useful when attempting to save money, but they are not the most convenient method of doing the work at hand.

WithoutTools

Yes, it is feasible to erect a roof top tent on your own, without the need of any tools or other special equipment. But it may be a challenge sometimes! Using any of the tools listed above would make your life a lot simpler and less stressful (literally). Even if you have no other equipment, you will eventually have to deadlift, squat, and shoulder press the tent on your own, which will be exhausting. The greatest hazard is that you will not lift correctly and will harm yourself, or that you will slide and the tent would damage your vehicle.

1. Place the tent near the car such that you may lean it against the roof racks at some point (either in the rear or on the side). Place the tent on its side so that it has a less distance to go before it comes into contact with the roof racks. Lift the tent till it is touching the roof racks
2. Then lower it again. Begin to rotate the tent up and over as soon as it reaches the edge of the platform. Lifting and pushing the remaining tent onto the roof racks is recommended.

In the event that you own a pickup truck or ute, you can complete this task in two stages. The first part involves loading it into the tailgate, and the second stage involves hoisting it onto the roof. This is not feasible for the majority of individuals, especially given the average weight of the tent, which is equivalent to raising another person over your head. This is by far the most affordable choice, and it may also be the least time-consuming due to the fact that you will not be installing any additional tools.

However, it will save you time and money in the long run.

Can I Remove a Rooftop Tent By Myself?

Yes, you can remove a roof top tent by yourself, however we recommend that you employ a hoist or track system to make the process as smooth as possible. At the very least, gravity will be on your side this time, and you will use less raw power to remove the tent this time. However, extreme caution must be exercised to avoid scratching or dropping the weight. Consider putting down a moving blanket to cushion any unexpected bumps throughout the transfer.

Hoist

With the hoist system, you would simply re-attach the straps, raise, and drive away, which would be the most painless technique. Simple!

Tracks

In order for the track system to be effective, the tent must be wiggled or moved onto the track system itself without touching the top of your car.

Because the tent is now on your roof, it will be much more difficult to create the tracks below the tent in order to remove it off the premises. In order to return the tracks to their original positions, you must first attach the tent to them.

Without Tools

It will be easier to take down the tent using brute force than it will be to put it up. Take your time and allow gravity to assist you remove your tent from your car. Use the front of your car as a transition point, allowing you to step on the ground and continue your removal without dropping your tent. Overall, the tent’s disassembly is as straightforward as it appears, and it follows the same procedure as the assembly, just in reverse.

Should I Ask for Help Instead of Installing it Solo?

YES! A good rule of thumb is to always ask for assistance if you believe you require it. Even if you are confident in your abilities to do the task on your own, having a second person on hand might help the procedure move much more quickly than you imagined. Furthermore, they may be able to spot things that you do not, whether it is discovering stuff you cannot see, such as screws and nuts, or checking that the tracks do not scrape your vehicle or that the hoist is correctly attached, among other things.

Risks of Putting a Roof Top Tent by Yourself

It is true that there are a lot of risks and dangers to be aware of while attempting to set up the roof top tent on your own.

• Danger of harming yourself (especially your back): Wear work gloves to protect your hands from any wounds caused by bracketry or exposed metal. – Lift using your legs, not your back, to ensure proper form. Accidentally damaging the car– when putting the tent up, there is the possibility that you will slide and scratch, dent, or otherwise harm the vehicle. Make a plan and practice it on a piece of grass first. Inquire for assistance
• Damage to the tent — lowering the tent from that height will cause the tent to be damaged. No matter if you are ripping the canvas or snapping certain components on contact, you are putting your lovely tent at risk of being ruined. Asking for help does not have to be a source of embarrassment. Roof top tents are cumbersome to transport and difficult to set up. Having an extra pair of hands will make the task much more efficient.

Conclusion

With the help of a hoist or tracks, you may quickly and simply set up a roof top tent on your own. If you use hard mode as your default setting, manually raising and pushing the tent is a possibility (and one that is not recommended). Hoists are systems that allow the tent to be lifted into the air with the push of a button or turn of a crank. Tracks are simple enough to use to raise the tent into place and move it over to the vehicle’s top. Despite the fact that this post was mainly focused on solo installations, we would want to emphasize the hazards and dangers associated with them.

Roof Top Tent Hoist & Storage Solution for Tacoma, RTT Garage Hoist

Ever stepped out into your garage and looked at your rooftop tent leaned up against the wall and thought to yourself, “Wait a minute. That’s not going to work.” That enormous, space-consuming rooftop tent off your garage floor and safely tucked up against the ceiling may be within reach thanks to a clever idea I’ve come up with. This is not a one-size-fits-all package that can be used immediately out of the box. Keep in mind that not all rooftop tents are made equal in terms of dimensions, so you may need to make a few additional adjustments.

You may look up the specifications for your personal rooftop tent before attempting this installation, but for reference, our specifications are as follows.

• Size and weight are both 114.64 lbs
• Dimensions are L 58.00in x W 48.00in and H 17.00in
• Weight is 114.64 lbs

WHY I CHOSE RACOR AND WHERE TO FIND IT:

The price of this lift, which I bought online on Amazon for less than $250, was by far the most economical alternative available.

The utilization of electric hoists and manual pulleys were also employed by some of the companies. Three elements influenced my decision to purchase the Racor:

• Because there were fewer pieces, there were less things that might go wrong. It was a pleasant buy because of the reasonable pricing and the Amazon Prime return policy. The ease with which it can be used

STEP-BY-STEP ROOFTOP TENT HOIST INSTALL VIDEO – ADVENTURE BUILT

• Tools: Stud Finder
• Cordless Drill/Driver
• Philips Screwdriver or Philips Driver
• Wrench
• 10mm Socket
• Pencil
• Drill Bits
• Safety Goggles

WHAT’S IN THE BOX

Everything in the Racor lift kit arrived in a well-organized and damage-free manner, thanks to the strong container it came in. The nicest aspect about this kit is that it has just 16 real components that are required to make the entire system function, and I only needed to utilize three of them. It’s so simple that even a caveman could do it. NOTE: The instructions ask for the construction of the three-wire platforms to be completed first; however, I did not intend to use the wire platform and hence skipped this step of the procedure.

STEP 1. MOUNT THE GEAR DRIVE TO THE BRACKET

In the kit, there are two brackets that are nearly identical in appearance. One is equipped with a bushing, whereas the other is not. The gear drive should be mounted to the bracket without the bushing on the side of the gear drive that has the four mounting holes (see illustration). To join the two pieces, use the four black short bolts with the Allen head to establish the connection.

STEP 2. MOUNT THE ARMS TO THE DRIVE AND NON-DRIVE BRACKETS

Install the four arms into the two brackets shown in the illustration above. The hardware is self-explanatory; the bag contains eight longer bolts and nuts. If you don’t already have one, you can buy one at any hardware store. I used pliers and a Phillips head screwdriver, but you may use any type of screwdriver. Step 2 has been completed.

STEP 3. IDENTIFY MOUNTING LOCATION THEN LOCATE STUDS

The tent needed to be above my garage door when the garage door was open in order to serve its role throughout the installation process. I started by measuring the distance between the garage door rails and then measured the space between my tent and the garage door rails. As soon as I confirmed that my rooftop tent would fit between the rails, I drew a line on the ceiling in the center of the space between the rails. Then I determined the center of the brackets and noted the center of the bracket with a pencil on the bracket.

• My worst nightmare was to lift the rooftop tent for the first time and have the side of it crash into the garage door rails.
• It’s time to find the studs.
• I have twin panels of drywall on my garage ceiling, and the studs are oriented in opposite directions; I believe this is due to the house’s architectural design.
• To discover my studs, I ended up drilling a small hole in my ceiling and using a GoPro and my iPhone as a monitor to film the process.
• After I had determined the precise location, I used my drill and the tiniest drill bit I had to co-witness the stud location with my eyes closed.

STEP 4. HANG THE FIRST BRACKET

Did I mention that this phase was extremely time-consuming? It was impossible for the bracket to install into more than two studs in my situation since they were so near to one other. So, in order to get a more stable installation, I decided to utilize two strips of 1″x3″ timber at a length of 6 12 feet to span the gaps between the studs and provide a more solid mounting place for the mounting brackets. After determining the stud placements for the first piece of timber, I buried it into the studs using three-inch-long lag bolts to secure it in place.

After the first strip of 13″ had been installed, it was time to attach the first bracket to the wall.

I fastened the bracket to the 1 3″ by inserting the provided lag bolts into each of the bracket’s accessible holes, which worked well. As soon as all of the bolts were sunk into the timber, I had complete confidence that the bracket would not come loose.

STEP 5. HANG THE SECOND BRACKET

In order to get 48″ away from the first bracket, I measured 48″ from the first bracket, found the center mark on the ceiling and the center mark on my 1 3″ and began sinking lag bolts into the ceiling studs via my 1 3″. Just so you know, I spent more than an hour on just one scene since my studs enjoy playing hide and seek with each other. Using a 13″ bracket, I made sure it was 48″ away from the first bracket and parallel to the first bracket. Don’t forget to check that it is parallel to the first bracket as well.

Once I had the bracket centered and parallel, I inserted a lag bolt into the center hole of the bracket to allow me to pivot the bracket in place.

I repeated the technique at the other end of my 1 3″ and finished it there.

See the “tiny” hole I made for my GoPro?

STEP 6. SLIDE TOGETHER THE AXLES

The axles are represented by the long bars included with the kit. I’ve marked the bars with a red arrow to denote their location. There are square ends on one end of each axle with tiny holes in them, through which bolts may be threaded and used to bind the axles to one another. Make sure the two ends of the bars are inserted into each other so that you can see the holes aligned. Continue sliding until the axles come to a stop against each other.

STEP 7. INSTALL CABLE ASSEMBLY RINGS

Two bags of steel braided cable with plastic discs weaved through them may be found in the hardware section of the store. A square end is located on each of the axle bars. Placing the plastic disc onto the bar end with the cable end towards the center of the bar is a good way to start. Adjust the cable center so that it hangs over one of the square’s faces, if necessary. Install the other cable package on the other end of the bar in the same manner as you did the first. Make certain that the cable is aligned such that the loop that falls over the square is on the same side on both bar ends as the loop that falls over the square.

STEP 8. INSERT AXLE INTO DRIVE GEAR

The axle has two ends, one with a tiny square end with a hole that may be used to take a bolt, and the other with a rounded end. We will be dealing with the square end of the pipe that is capable of receiving a bolt. Sliding the squared-off end of the axle into the driving gear should be done from between the brackets. It should be placed into the axle end with the tiny bolt and big flat washer and tightened down to ensure the axle is properly secured in place to prevent it from moving. Using a 10mm socket, tighten the screws.

STEP 9. INSERT NON DRIVE END OF AXLE INTO BRACKET

Insert the other end of the axle into the other bracket with the bushing, and then repeat the process on the other side. Once the axle has been installed, put the cotter pin into the hole to ensure that it does not slip out.

Make sure to bend the cotter pin in order to prevent it from falling out. I’m aware that there is a lot of possibility for falling going on, especially given that you are on a ladder. Take precautions. Please take your time.

STEP 10. ALIGN AXLE AND BOLT IT TOGETHER

To secure the axle together, use the remaining two bolts and nuts that are left on the axle. Using a 10mm socket, tighten the screws.

STEP 11. FISH THE CABLE ENDS THROUGH BRACKET ARMS

This stage is rather straightforward. The most difficult aspect is having to move the ladder four times. Simply pull the cable up and over the arm wheel on each end of the arm and allow it to fall to the ground on either end. It is important to align the lengths of all four wires once they have been laid flat on the ground, or as near to it as they can be as flat as possible. This will assist you in the hoisting of your rooftop tent at the same time. Additionally, it will store at the top in a neat and tidy manner.

STEP 12. ATTACH THE CABLE ENDS TO THE BARS

This step ended up becoming two stages for me. In the beginning, I planned to use a long 24 foot piece of timber with eyelets drilled into it to provide myself a wide base so that the rooftop tent would not be damaged. In the end, I decided to abandon this concept since it didn’t feel solid enough for my needs. In the end, I reverted to the original bar ends that came with the package. My rooftop tent fits snuggly between the huge eye-bolts and gives me a sense of security that I didn’t have before.

Insert the eye-bolt through the hole on the end of the bar.

Repeat this process three more times.

Congratulations, you have successfully finished the installation of your rooftop tent hoist system!

STEP 13. OPERATING THE HOIST

There are two silver-colored rods included in the package. One is straight with a hook at the end, while the other is curved in a U shape at the end. Also included in the package is a tiny bag that contains a drill chuck. The straight bar with a hook at one end is used to link into the loop of the gear drive and to rotate the loop that is connected to it. Lifting and lowering of the rooftop tent is accomplished by spinning that loop on the gear drive. On how to make the loop spin, you have two alternatives available to you.

• A screw and nut will be used to secure them together once they have been linked to the rod with the hook on the end.
• The second option is to make use of the chuck.
• After you’ve completed this step, insert the chuck end into any hand drill.
• You should utilize the red clasp on the gear drive since it is a safety feature, and I advise you to do so.
• To use the safety, insert the hook of the rod into the enlarged hole and draw the rod away from the loop until the safety is engaged.
• Once the safety has been released, insert the hook of the rod into the loop of the gear drive to complete the installation.
• The tent rises as the rotation is done in a clockwise direction.
• To raise my tent, I’ll have to utilize a mix of methods.

The hand crank helps me get it the rest of the way to the top because my drill isn’t strong enough to get it there all by itself. I have to raise the tent all the way to the top so that it contacts the arms of the hoist in order to get it out of the way of the garage door.

STEP 14. ENJOY YOUR NEW RACOR ROOFTOP TENT HOIST

You now have a long-term storage option for your rooftop tent that should last for many years to come. Cheers!

REVIEW

I can honestly say that I enjoy working with this kit. The installation of the Racor Ceiling Storage Lift was rather basic. The tent is easily maneuvered up and down the lift with no problems. However, what is most important to me is that the product seems strong, and I have confidence that it will not fall and do damage to my garage door, floor, or BMW R1200GSA adventure motorbike, which is parked just below it. After using it for more than a week, I’ve only had to lift and lower the camera a couple of times to make small changes and snap photos.

Outdoor Hoist System for Roof Top Tent

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) SPC UCA Alcan 750lb springs – 1″ lift SPC UCA Alcan 750lb springs 3″ Front: 1.65″ Rear to achieve a level surface +25 offset on Toyo ATII 35s Icon Six Speed tires Wheelers Superbumps Chrome Remove the ARE Z Topper with Thule Rails from your vehicle. Pinsu Topper rack RTT – Tepui Autana Ruggedized Pinsu Topper rack RTT – Tepui Autana Ruggedized 3 Inquiring whether anyone knows of an excellent outdoor hoist arrangement that is both reliable and affordable. In my vehicle, I’ve mounted the ARE-Z topper with the Prinsu rack on top, which makes it a bit taller than most other setups at 6.75 feet to the top of the rack. Because I am in possession of the topping. The height of my garage entry is insufficient for the installation of an interior hoist system on my ceiling. My tent would collide with the garage door opening. Looking for an outside solution that won’t become an eyesore in my front yard. To do this, I’d like to construct something that can be quickly removed and kept within the garage. I’ve discussed various possible solutions with family and friends, and the following is what I’ve come up with: Option 1) Pole and Hoist Frame: This option includes a pole and hoist frame. 2ft Sleeve: Dig a hole for a post and cement it in place (1.5″ galvanized steel pipe). Due to the fact that the pipe’s top will be at grade, it will not protrude significantly from the ground. – Insert a 12 ft tall, 1.25″ galvanized steel pipe so that it is snug against the 1.5″ sleeve. – Attach the Hoist Frame Arm to the pole – The hoist frame works on pipe up to 1.89″ in diameter. Viking Solutions Rack can be attached as an option number two. Lifting Device: Jack II Hoist (also known as Jack II Hoisting Device) A very comparable model is owned by my next-door neighbor, however it does not function very well from the hitch owing to the restrictions of the swivel. The fact that this Viking model has an attachable floor mount is one of the reasons why I prefer it. With the floor mount, I could theoretically lift the tent up, back the vehicle up, and then place the tent on the roof rack to protect it from the elements. Any further suggestions would be much welcomed
• What do you think about a rolling gantry? You can acquire a one-ton load for around $600. What is the weight of the tent? Check on the port’s freight. Whenever it’s not in use, you may roll it into the garage.

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) springs: SPC UCA Alcan 750lb springs with a +1″ lift, 3″ front lift, and 1.65″ rear lift to level the vehicle +25 offset on Toyo ATII 35s Icon Six Speed tires Superbumps for Wheelers Chrome Remove the ARE Z Topper with Thule Rails from your vehicle. Tepui Autana Pinsu Topper Rack RTT – Pinsu Topper Rack RTT – Tepui Autana The 3tent is ruggedized and weights 190lbs. I was attempting to avoid paying more than $200-$300 since I was concerned about bending a 1 1/4″ pipe. Your tent and hoist aren’t particularly heavy in and of themselves. However, I believe that if you move them far enough away from your truck, the pipe will collapse. The gantry concept appeals to me. You could definitely make something similar out of a smaller pipe. Raise the tent, transport it to a new location, and then lower it into a wagon. Construct the gantry so that it can be collapsed and stored with ease

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) springs: SPC UCA Alcan 750lb springs with a +1″ lift, 3″ front lift, and 1.65″ rear lift to level the vehicle +25 offset on Toyo ATII 35s Icon Six Speed tires Superbumps for Wheelers ARE Z Topper with Thule rails in chrome deletion Pinsu Topper rack RTT – Tepui Autana Ruggedized 3 – Pinsu Topper rack RTT That’s something I’d have to hire someone to do. Would almost certainly be rather expensive, I’d guess. Other than a wood version, the only other less expensive option I could think of is:

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) springs: SPC UCA Alcan 750lb springs with a +1″ lift, 3″ front lift, and 1.65″ rear lift to level the vehicle +25 offset on Toyo ATII 35s Icon Six Speed tires Superbumps for Wheelers ARE Z Topper with Thule rails in chrome deletion Tepui Autana Pinsu Topper Rack RTT – Pinsu Topper Rack RTT – Tepui Autana Ruggedized 3
• With a platform that you can drive the wheel into, the choices for where you wish to remove the tent are virtually limitless. Make the frame in such a way that it can be readily collapsed and transported around with you

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) springs: SPC UCA Alcan 750lb springs with a +1″ lift, 3″ front lift, and 1.65″ rear lift to level the vehicle +25 offset on Toyo ATII 35s Icon Six Speed tires Superbumps for Wheelers ARE Z Topper with Thule rails in chrome deletion Tepui Autana Pinsu Topper Rack RTT – Pinsu Topper Rack RTT – Tepui Autana Ruggedized 3Cool design would be ideal, but it would be far more expensive than I am prepared to spend. Another stuff to lug about with me is probably not something I’ll need any time soon. For the time being, a $60 chain fall will suffice.

KMGNew Member

• Date of joining: October 7, 2018 Member:20257 Messages:275 Gender:Male Kevin Yacolt’s first name is Kevin, and he lives in Washington. TRDBFG KO2s, TRD Rear Sway Bar, Firestone RideRite Air Bags, B W Gooseneck Hitch, Trail Ridge Package 2018 White Tundra Limited DC 4×4 TRDBFG KO2s, Trail Ridge Package Towing Mirrors with an Extendable Arm Make use of the receiver hitch on your car as a mounting point. Make a simple crane hoist that can be swiveled about 180 degrees. When not in use, the crane’s boom arm should be designed to fold flat against the vertical pole to maximize compactness.

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles SPC UCA Alcan 750lb springs – +1″ lift 3″ Front: 1.65″ Rear to level Toyo ATII 35s Icon Six Speed +25 offset Toyo ATII 35s Icon Six Speed +25 offset Superbumps for Wheelers ARE Z Topper with Thule rails in chrome deletion The Pinsu Topper rack RTT – Tepui Autana Ruggedized 3 is a ruggedized version of the Pinsu Topper rack.

KMGNew Member

• Date of joining: October 7, 2018 Member:20257 Messages:275 Gender:Male Kevin Yacolt’s first name is Kevin, and he lives in Washington. Toyota Tundra Limited DC 4×4 TRDBFG KO2s, TRD Rear Sway Bar, Firestone RideRite Air Bags, B W Gooseneck Hitch, Trail Ridge Extendable Towing Mirrors 2018 White Tundra Limited DC 4×4 TRDBFG KO2s There is no connection. I’m just having a brainstorming session. In my opinion, the vehicle serves as a stable platform, and the receiver hitch provides a reliable mounting place. In order to hoist the RTT, I’d start with square tubing with an outside diameter that fits into your receiver and cut it to a length that clears the rear of your vehicle. I’d then vertically weld on tubing with the same diameter and a length long enough to clear your roof rack while hoisting the RTT. I’d build my boom arm to be long enough to take up the center of the RTT plus 24 inches on either side “. Weld a 12″ circular tube 24″ from the non-lifting end of the boom with an o.d. to fit into the vertical mast at a distance of 24” from the lifting end of the boom. This is the boom pivot, which is located at the top of the vertical mast and allows the device to be disassembled into two sections for storage. The additional 24 hours “The length of the boom is to accommodate a counterweight equivalent to your RTT. Please accept my apologies for the lengthy description. A tower crane that has been shrunk down in size

bfd300New Member

• Date of joining: September 27, 2018 Member:19887 Messages:364 Gender:Male

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) springs: SPC UCA Alcan 750lb springs with a +1″ lift, 3″ front lift, and 1.65″ rear lift to level the vehicle +25 offset on Toyo ATII 35s Icon Six Speed tires Superbumps for Wheelers ARE Z Topper with Thule rails in chrome deletion Pinsu Topper rack RTT – Tepui Autana Ruggedized 3 – Pinsu Topper rack RTT If only I knew how to weld or possessed the necessary tools. It appears to be entertaining. I’ve only come across someone welding a few of times.

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) springs: SPC UCA Alcan 750lb springs with a +1″ lift, 3″ front lift, and 1.65″ rear lift to level the vehicle +25 offset on Toyo ATII 35s Icon Six Speed tires Superbumps for Wheelers ARE Z Topper with Thule rails in chrome deletion Pinsu Topper rack RTT – Tepui Autana Ruggedized 3Boom arm on these designs isn’t long enough to reach the ground. My next-door neighbor had one that looked precisely like this, but it also rotated 360 degrees. Because that arm is so short, we were never able to get the tent to be correctly oriented. Then, when we raised it to a height that allowed it to clear my topper and rack, the steel became compromised and burst loose on one joint owing to the weight of the top. 8 feet above the ground

SeanO86Live Slow. Die Whenever.

• Date of joining: February 1, 2018 Member:12602 Messages:93 Gender:Male SeanColorado is his given name. Toyota Tundra TRD Off Road 2018 SR5 – Cement
• Fox Racing Tires 2.5 with Resis+1 CB Shackles (with Resis) Toyo ATII 35s Icon Six Speed +25 offset Toyo ATII 35s Icon Six Speed +25 offset Toyo ATII 35s Icon Six Speed +25 offset Toyo ATII 35s Icon Six Speed +25 offset Toyo ATII 35s Icon Six Speed +25 offset Superbumps for Wheelers ARE Z Topper with Thule rails in chrome deletion Pinsu Topper rack RTT – Tepui Autana Ruggedized 3 – Pinsu Topper rack RTT This would not be sufficient to clear the topper and rack. This one has a maximum height of 56 inches. I need to travel around 7ft.

DividedSkyNew Member

• Date of joining: November 16, 2017 Member:10993 Messages:897 Gender:Male Jeff is his given name. The vehicle is a ’18 Crewmax with ADS Mid Travel and ADS 2.5’s (rear bypass) U748 Leaf Springs is a postcode in the United Kingdom. I’m curious if anyone has come up with anything substantial in the meanwhile. I recently purchased an RTT and am currently attempting to figure out how to transport it on and off my vehicle. I won’t be able to use a garage ceiling hoist since my vehicle with tent will be too tall to fit through my garage door. Right now, my natural instinct is to construct something along the lines of: The legs would be made of two 2x4s (one perpendicular to the other, forming a “T” for support in both planes), and the top would be made of a 2×6 or similar material. In order to be able to fold it up for storage, the top section would be hinged using saw-horse brackets (rated to 400lbs). This would be done through the use of two pulley systems that I observed at Harbor Freight: Because the pulley system has a 4:1 ratio, only 25lbs of force is required to raise 100lbs of weight. The only concern I can see is that I may need to add some more supports to the lift mechanism to prevent it from moving side to side during operation. Thoughts

Sunnier“DO it!”

• Date of joining: August 21, 2017 Member:9171 Messages:9,737 Sunny is her given name. San Diego, California Vehicle:2017 The Tundra is ablaze in the Inferno DC. Longtravel 1st Gen, Banner/Hulk, TRDLongtravel The smashing of the construction However, I believe that the wood strength will be insufficient to support the height and weight of an RTT, as well as the dynamic sway that will occur during the construction of the RTT. A larger investment in terms of money and area, as well as the time required to create it, would most likely be successful: Build it entirely of steel, basically a heavy-duty swing set. It would be much better if you could embed it in the ground using concrete. However, I suspect that this is not the low-cost answer that the OP is seeking for.

DividedSkyNew Member

• Date of joining: November 16, 2017 Member:10993 Messages:897 Gender:Male Jeff is his given name. The vehicle is a ’18 Crewmax with ADS Mid Travel and ADS 2.5’s (rear bypass) U748 Leaf Springs is a postcode in the United Kingdom. Instead of the design you see above, I came up with something else entirely! This one takes use of the existing framework of my house to provide additional strength, while being somewhat movable. I can easily lift it, and the “arm” pivots down to allow it to be stored in a relatively small space. Take note of the red line that I’ve drawn in the image. This structure has an insert that fits between the two uprights and the roof joists sandwiched between them. When the rig is under stress, this is what prevents it from tilting forward and from shifting from side to side as well. My 8-year-old can easily hold my weight, as you can see in the second photo, and the lift is easily capable of supporting my entire body weight, as seen in the first. If it can keep up with me, it should have no trouble supporting an RTT (or two).

DividedSkyNew Member

• Date of joining: November 16, 2017 Member:10993 Messages:897 Gender:Male Jeff is his given name. The vehicle is a ’18 Crewmax with ADS Mid Travel and ADS 2.5’s (rear bypass) U748 Leaf Springs is a postcode in the United Kingdom. By the way, this was my source of inspiration

Casper421Double cab is the best cab!

• Date of joining: July 12, 2017 Member:8530 Messages:3,235 Gender:Male In the woods, there’s a guy named Chris. 06 DC is the vehicle number. Yes, I really have a 200-year-old oak tree in my yard. It’s something I’ve been using for years.

KarmaKannonMaster of None

• Date of joining: June 3, 2019 Member:31428 Messages:1,924 Gender:MaleUtah Vehicle:2006 Double Cab with a lengthy travel distance There’s some s**t. I’d just do it this way, but then again, I’m a stubborn person. Perhaps a trailer hitch attachment welded to a tall enough pipe, with an arm extending from the pipe just long enough to reach the middle of your tent, might be appropriate. Make use of a chain to fall off an arm. Rotate the arm to the opposite side and drop it to the ground, if necessary.

OutboundSSEM2.5, with a taste for roasted pigeon

• Date of joining: August 2, 2016 Member:4064 Messages:6,964 Gender:Male Aaron is a first name from Northern Alberta. Vehicle:2005 The Toyota Tundra Doublecab TRD Off Road vehicle. I’ve come up with a four-step solution: 1. Join a fitness center. 2. Put on some muscle, buddy! Particularly effective are deadlifts and overhead presses. 3. You can easily lift the tent onto the vehicle by yourself. 4. Acquire a stick with which to ward off the hordes of ladies who will swarm you as a result of your absurd display of manliness. JC303 and Marty McFly are fans of this

Winning8New Member

• Date of joining: 4th of July, 2019 Member:32819 Messages:1,228 Gender:Male The San Francisco Bay Area MGM DC 4×4 SR5 (2019 model year) Mumba Bench seat cover, 18×9 18 offset rim, diamond back HD cover, LED headfog light bulb, TRD rear sway bar, timbren enhancement, avs auto shade and diamond back HD cover Why isn’t anyone using an engine hoist?

PinayNew Member

• Date of joining: September 14, 2018 Member:19379 Messages:15,701 Gender:Female First and last name:Monet Dirty Seven Club 2015 Black SR5 CrewMax 4×4 TSSDirty Seven Club Vehicle Information Kuya, thank you very much. This individual is insufficiently tall. The height of my bed rack is 18″ above the edges of the bed. Check out @DividedSkyhis post for more information! In addition, page 8 of my build thread contains my own interpretation of this hoist

Winning8New Member

• Date of joining: 4th of July, 2019 Member:32819 Messages:1,228 Da Bay Area is a male-dominated region. MGM DC 4×4 SR5 (2019 model year) Mumba Bench seat cover, 18×9 18 offset rim, diamond back HD cover, LED headfog light bulb, TRD rear sway bar, timbren enhancement, avs auto shade and diamond back HD cover A The garage door is only 7 feet tall, and the hoist’s maximum lift is 7 feet 10 inches. Of course, as you extend the arm, the burden is reduced
• I believe the maximum load with the arm fully extended will be 14 tons. Perhaps a 2 ton hoist would be a better choice
• With the arm completely extended, the maximum load should be 12 tons.

DividedSkyNew Member

1. Date of joining: November 16, 2017 Member:10993 Messages:897 Gender:Male Jeff is his given name. The vehicle is a ’18 Crewmax with ADS Mid Travel and ADS 2.5’s (rear bypass) U748 Leaf Springs is a postcode in the United Kingdom. Thank you for the compliments! In fact, I’m preparing to make some substantial adjustments in my life (although the general premise will remain the same). To save time, I’m planning on incorporating a furniture dolly into the base so that I can just wheel it over to the truck, connect it onto the rack, and then hoist it with the pulley
2. Instead of hauling the tent from the garage and then onto the “lift,”

How Do You Store A Roof Top Tent [GUIDE]

A rooftop tent is a wonderful method to make your sleeping experience more convenient than a standard tent on all of your overland excursions. Not only are they more comfortable and long-lasting, but they’re also simple to set up and take down while on the road. This is very beneficial when you need to keep something when it is not in use. What is the proper method of storing a rooftop tent? The rooftop tent should be carefully removed from the vehicle and stored in an area that is both dry and elevated off the ground in order to be stored correctly.

Because most tents are built to be used in three seasons—and because, no matter how much you’d like to, you probably won’t be overlanding all of the time—knowing how to store your rooftop tent properly is essential for keeping it in good condition.

The manner you store your tent will be determined by your available space, the style of the tent, and the amount of use you anticipate.

The Right Way to Store Your Rooftop Tent for the Off-Season

The most effective manner to store your rooftop tent will be determined by the restrictions of your available space as well as the style of tent you own. All rooftop tents should be stored above the ground to prevent animals from getting inside the tent and in a dry area to avoid the tent from being damaged by weather or water exposure. The following are the most important stages in properly storing a rooftop tent:

1. Considering storage capabilities and selecting an appropriate approach
2. Removal from car in a safe manner
3. Putting the tent in its proper location

Address Storage for Rooftop Tent

Before you do anything else, you’ll want to make sure that your rooftop tent will fit in the new location. Ceilings and walls are the most suitable places to hang or store a rooftop tent because they meet the following requirements:

• Avoid putting your rooftop tent on the ground: It’s advisable to avoid putting your rooftop tent on the ground in order to prevent it from further damage. The tent, especially if it’s kept in a garage or shed, may appear to be an enticing abode for small creatures such as mice, who may do damage to the covering or attempt to make a home in it. Because you are on the ground, you will be more vulnerable to water damage if a flood strikes. Ensure that the tent is stored in a dry environment: In addition to keeping it off the ground to minimize flooding, make sure that you store it in a location that will remain completely dry. The presence of excessive moisture or adjacent water may cause harm to the covering or allow mold to grow within. Water damage to your roof top tent cannot be prevented just by using a roof covering. Make certain that there are side walls as well. There are several ways for rain and moisture to enter a building. Placement in a safe environment: Check to see that the tent is stable and will not collapse (or off the wall or ceiling). This has the potential to cause structural pieces to fail, particularly in more fragile models. Because of the increased danger of contact and damage, avoid resting tents up against a wall at an angle or positioning them in heavily trafficked areas where people will be passing by. The fact that they are not properly anchored further increases the possibility of injuring someone should a tent fall on them (particularly with larger ones)

Keep your rooftop tent off the ground: It’s ideal to keep your rooftop tent off the ground in order to prevent it from sustaining further damage from the elements. The tent, especially if it’s kept in a garage or shed, may appear to be an enticing abode for small creatures such as mice, which might do damage to the covering or attempt to make a home in it. It is also possible to get water damage if you are on the ground during a flood. The tent should be stored in a dry place: Keep it off the ground to minimize water damage, and store it in a dry location to ensure that it doesn’t become soaked.

Water damage to your roof top tent cannot be prevented just by the roof.

There are several ways for rain and moisture to enter the building.

Especially with more sensitive versions, this might result in structural pieces breaking.

The fact that they are not properly anchored further increases the risk of injuring someone should a tent collapse on them (particularly with larger ones);

Removing a Rooftop Tent from Vehicle

A rooftop tent might be difficult to remove, especially if you are attempting to do it without assistance. The most straightforward method of removing the tent would be to assemble a large group of people and carefully hoist it off the vehicle. Alternatively, if no one is accessible and your squad is still unable to remove the tent, you’ll need to get a little more inventive:

• Lift or hoist system: While your car is parked in the garage, use a roof-mounted hoist or lift to remove the tent from the roof of your vehicle. When using this approach, you simply need to remove bolts and slide straps or cables, and then you can sit back and let the lift take care of the rest. We’ll go into further depth on how to accomplish this later. Forklift: If you have access to a forklift (which most people do not), this is arguably the quickest and most convenient method of removing the tent. Just make sure you keep an eye on where your fork is placed. You don’t want to inadvertently cause damage to your equipment. Using a wooden ladder and an electric winch is a very easy and unique method that involves only the construction of a wooden ladder with 2x4s and a few hooks at the end. Using a winch rope, elevate the ladder until it is parallel to the vehicle’s roof, and then lower it back to its original position. Slide the tent to the opposite end of the improvised ladder and use the winch to slowly lower the tent from its elevated position. There is no need to lift anything (or phone pals).

Rooftop tents are strong and long-lasting, but they should be stored out of the way when not in use. This will not only protect them from getting in the way, but it will also preserve them in excellent shape.

Rooftop Tent Removal Tips

It might be time-consuming to take down your rooftop tent. In the event that you need to remove your tent frequently, we recommend utilizing a lift system or picking a lightweight tent that is easier to operate on your own (or with one other person).

Where to Store Your Rooftop Tent

There is plenty of room to store a Roof Top Tent. Rooftop tents should be secured to a ceiling, wall, or other elevated surface for the most safe storage. The majority of rooftop tents are stored in the garage since there is more space, it is shielded from the weather, and it does not take up valuable inside space in your home. Depending on the technique you pick, you will have to store your tent in a different manner:

• Storage on the ceiling: Storing a rooftop tent on the ceiling is a popular option since it keeps the tent out of the way and out of the way of guests. When installing ceiling hooks or brackets, always sure to check for studs first. You don’t want the tent to come crashing down on someone. Wall Storage: Wall storage is most effective for smaller tents that can be held up with straps and fixed to a wall with relative ease. There are less restrictions in terms of space for the vast majority of individuals, but it may not be able to accommodate the same amount of weight as a ceiling lift. Brackets are screwed into a wall and tied together to keep the tent in place. Look for studs to help support the weight once again. Storage on a Cart or Platform: If you don’t like the look of wall or ceiling storage, a movable cart or platform will meet all of your needs while also providing simple movement. This is also the greatest alternative for individuals who need to relocate their tent a longer distance away from their vehicle.

The ideal solution for you will be determined by your available storage space as well as your particular preferences. They’ll all do the job, so just pick the one that appeals to you the most!

How to Store a Rooftop Tent in a Garage

If you have the space, you may simply store a rooftop tent in your garage if necessary. When it comes to storing your rooftop tent, there are several options. Modern methods will make the movement from car to garage easier and more easy, allowing you to quickly build and remove the tent whenever you need. A rooftop tent may be stored in a garage in several ways, the best of which are as follows:

• For ceiling storage, a lift or suspension mechanism should be installed. Create or utilize a wheeled cart to make moving around easier
• Attach a rooftop tent to the wall of a garage
• A elevated platform should be used to set up a rooftop tent.

The manner of storage you pick will be determined by your preferences and practicality. The greater the ease with which you may store your tent, the more probable it is that you will remove your tent when it is not in use. We’ll go through each of these possibilities in further depth so that you can make an informed decision about which one is best for you.

Lift/Hoist System for Rooftop Tent Storage

The use of a lift or hoist system to store a rooftop tent in your garage is one of the most space-saving and handy options available. While it may take a little longer to set up at first, you can quickly transport the tent from one location to another with the vehicle’s trunk open (not just for off-season storage). You can easily raise the tent from your roof with the use of automatic electric or manual pulley systems. If you intend to make use of this storage method, you must first determine whether or not it is viable for your garage’s architecture.

Depending on where it is located and how large it is, it may cause interference with the garage door’s opening and closing.

You can rely on us.

Because of the weight of your tent, drywall is not a strong enough support.

Heavy-duty lifts will be able to support significantly more weight, so check sure the weight capacity is more than the weight of the tent itself before purchasing one. As an example of how this sort of system can appear, consider the following:

Setting up a Lift or Hoist System

Setting up a lift or hoist system is as follows (be sure to follow the manufacturer’s instructions for any lift system you use):

1. Make certain that the harnesses or wires are mounted to the ceiling in a structurally sound area before proceeding. Your tent’s mounting brackets should be spread out to correspond with the positions of the mounting brackets on your tent. Add supports or hooks to the cross support: This allows the tent to be entirely removed while the crossbars are still below, making it easier to put up and take down. Unscrew and remove the tent’s mounting brackets, which will allow the entire system to be removed off the car. Support straps or wires with loops: In order to ensure that the tent suspends safely over the vehicle, ensure that the lifting mechanism is properly attached on all sides of the tent. Height can be adjusted by using a pulley or an automated system to raise or lower the straps or cables as needed to achieve the desired height.

Systems like this can be looped onto the rooftop tent case directly, wrapped around the case with straps, or used in conjunction with support bars below the tent case. It is recommended that you secure the tent with additional carabiners in order to provide greater stability. Make a pulley system to provide a comparable DIY solution if you want to save money. Here’s a nice video on a do-it-yourself storage solution:

Wheeled Carts for Rooftop Tent Storage

With a cart, there are less logistics to consider because it can be positioned almost wherever that there is space. This might be a cart that you build yourself or one that you purchase pre-made for convenience. Rooftop tents may be rather substantial in weight. A cart will make it simpler to carry them about your garage on a cart, but it will not make it any easier to transfer them from the top of the vehicle to the ground on a regular basis. This option is recommended if you have enough of storage room in your garage and will only be removing your tent during the off-season (unless your tent is super lightweight).

In addition, locking wheels should be considered so that the item does not roll around in the storage space.

This will also make it simpler to relocate if the need arises (for example: to a shed that is not close to your car).

Wall Storage for Rooftop Tents

Installing your rooftop tent on a wall in your garage is another method to conserve room on your floor. When compared to your ceiling or cart options, this one might be a little more difficult in terms of weight distribution. Most of the time, this would be performed by attaching brackets above and below the tent and anchoring the tent using tie-down straps or ratchet straps. Our recommendation is for lightweight rooftop tents only, due to the fact that wall brackets will not be able to sustain as much weight.

The use of loops on the tent cover will simplify the process of fastening the tent to the wall and keeping it there.

The optimum time to employ this storage option is during the off-season or when you will not be utilizing your tent for an extended length of time.

Raised Platform for Rooftop Tent Storage

When it comes to storing your tent, the most straightforward answer is to build a raised platform in the garage. However, this does not always imply that it is the most effective use of available space. Build the platform yourself out of boards of wood if you want to save money.

Just make sure it’s sturdy and will be able to support the tent without tipping over or breaking apart. This may also be an excellent alternative for keeping your tent in a shed, as long as the tent is kept sheltered from the weather conditions.

To Remove or Not to Remove: Taking Off Your Rooftop Tent for Storage

If none of the above-mentioned storage options are appropriate for your needs, it is feasible to keep your tent on your overland rig all year. Some tents and living arrangements will not permit this, therefore you must ensure that if you wish to keep the tent up, it will be safe to do so before proceeding. The following are the ideal circumstances for storing a rooftop tent on a car throughout the year:

• Garage or covering with suitable height: If your garage or covering has enough height to accommodate your vehicle with the tent connected, you can leave it up. When left outside, this will prevent damage caused by the weather as well as the potential of theft. Despite the fact that most tents have a waterproof/weatherproof shell, they are not meant to be stored outside on a regular basis. If you do decide to leave it outside, be certain that the case is durable enough to survive the elements. This is more realistic in climates where there is no snow. Vehicles that are rarely driven include: In the event that you don’t intend to use your overland vehicle every day, it is quite OK to leave the tent set up all year. Simply ensure that the vehicle is sheltered from the elements while it is not in use.

In the event that you do not fall into any of these situations, we recommend that you remove your rooftop tent while it is not in use (at least over extended periods of time). It is also true that leaving it on the roof of many vehicles may lead you to waste more petrol as a result of the constant wind resistance and increased drag.

Properly Storing a Rooftop Tent

Rooftop tents can make any outdoor camping trip more enjoyable, and taking good care of your tent is essential if you want to get the most out of your investment. The method of storage you choose will be determined by your available space as well as how frequently you intend to remove your tent. Storing your tent indoors during the off-season is the most effective method of maintaining it in good condition and reducing the likelihood of damage or theft from occurring. Take good care of your rooftop tent, and it will look after you and your belongings on the path for many years to come.