How To Install Exhaust Fan In Grow Tent

How to Install Inline Duct Fan in Grow Tent

One of the most effective methods to get started in gardening or a DIY agricultural project is to get an indoor grow tent. There are a number of important aspects to consider in order to guarantee that your grow room operates at peak efficiency. For example, the quality of the air that your plants breathe has a big impact on the overall growth levels of your plants. Consequently, knowing how to install an inline duct fan in a grow tent is one of the most important considerations to make in this process.

First and foremost, you will want sufficient ventilation to aid in the promotion of the development of your plants.

Even more importantly, it will assist in cleansing the air.

As a result, your plants will develop into healthy and robust individuals.

Installing an Inline Duct Fan in A Grow Tent

While installing an inline duct fan may appear to be a difficult task, it is actually rather straightforward and may be completed by the homeowner. You will only need to be aware of a few important parts of the procedure in order to succeed. One of the most important considerations is that the ducts should be straight and without any bends in order to provide adequate air flow. To assist you in appropriately installing the duct fan, here are some suggestions to remember:

Mount Your Inline Fan on the Tent Ceiling Bars

After you’ve set up the tent, the following step is to attach the inline fan to the ceiling. Generally speaking, mounting the fan to the ceiling bar of the grow tent is the most suggested method. As a result, try utilizing adjustable clips to assist you in hanging the fan and allowing it to dangle a few inches below the ceiling. It’s a procedure that will guarantee that you have enough room on the ground and will also aid in the removal of hot air from the upper area of the tent throughout the night.

  1. The most important component of this operation is to make certain that the carbon filter is installed appropriately.
  2. Furthermore, you have the option of hanging it or choose to set it in a secure spot on the floor.
  3. Once the fan is in place, make sure the tapered end of the fan is towards the exhaust hole.
  4. Check to be that the flange end of the filter is directly facing the filter when installing it.

Clips should be used to attach either end of the duct to the sandbox. The other part was then attached to the carbon filter. It is possible that you will need to use a different method for filters that will be placed on the flow.

Connect the Fan to the Ducting

In the event that you fail to properly connect your inline fan to the ducting system, hanging it may be ineffective. As a result, make certain that the ducting is correctly connected so that the free circulation of exhaust gases is promoted. Aside from that, the pipe should be free of flaws and should not have any bends that might result in holes. Even more importantly, the ducting should not be too long since the length may reduce the efficiency of the fan’s operation. Remember to exercise caution so that light does not get through the ducting into the grow tent, which is designed to be light resistant in the first place.

  1. Keep in mind to make sure the ducting is routed through an exhaust port.
  2. If you leave it neglected, it might serve as an access point for vermin and other unwanted visitors.
  3. When connecting the fan to an electric source, take precautions to guarantee the highest level of safety.
  4. The use of a competent electrician to assist with electrical connections is highly recommended while making these types of connections.
  5. For example, make certain that the fan is connected to the right power outlet in order to avoid problems such as surges.

Inline Duct Fan Set Up in Grow Tent Frequently Asked Questions (FAQ)

A. Yes, a fan is required in your tent in order to assist adjust the air quality in the shelter. The humidity and temperature levels required by the plants in the grow tent must also be precisely controlled for maximum growth. A fan in a grow tent will ensure that air is circulated properly, and you will find it simple to regulate the temperature to meet your specific demands.

Q. How long do I keep a fan in my grow room?

A. It is entirely dependent on the inside conditions of the grow chamber, as previously stated. When you believe the temperature and humidity levels have risen over the acceptable ranges, you may always switch them off completely. Later on, you will have the option of scheduling the fan to turn on and off at certain intervals. For example, you might set the fans to run in 10-minute intervals every hour for a total of 1 hour.

Q. Why do I need a fan in my grow room?

When it comes to managing air quality, a fan is really important. Plants are living entities, and they require clean air for a variety of reasons, including growth.

In contrast to a typical farm, a grow room necessitates the use of artificial resources in order to regulate the air quality. Keep in mind that the quality of the air in the grow room is directly linked to the amount of yield you will receive from the space.

Q. How often can I run the exhaust fan in a grow tent?

An important function in controlling air quality is played by a fan. A. Plants are living entities that require clean air for a variety of reasons, including growth. It takes artificial resources to maintain the quality of the air in a grow room, as opposed to a conventional farm. Maintaining a high-quality indoor environment is essential for maximizing the production from your grow room.

Q. How do I install a duct fan in the grow tent?

When it comes to this operation, components such as insulated and heavy-duty ducts are frequently utilized. The efficacy of a device is greatly influenced by factors such as its length and size. Make sure the duct is as short as feasible, which is a good tip. This one-of-a-kind length contributes to reducing the distance that air must travel before exiting the garden.

Q. What size extractor fan do I need for a grow tent?

A variety of factors influence the selection of the best fan for your grow tent. For example, the size of the grow room and the quantity of plants in the space are important considerations.

Q. What is the size intake fan for a grow room?

Inline fans must provide 1 CFM per square foot of available area in the room, which is the industry standard measurement. You can find out the size of your room by multiplying the length by the breadth of the room. This should assist you in gaining a notion of the size of the system you have and the intake fan that will be appropriate for it as well.

How Does an Inline Fan Work?

An inline exhaust fan may best be characterized as a fan that is installed inline with a pipe to remove waste from the system. Even more so, the fan is often built in a location that will give the greatest amount of air filtering advantages possible. The effectiveness of the fan is influenced by a number of different aspects. When it comes to the capacity of the fun, the distance between the ducting where the air goes through will be determined by several factors. In addition, the power rating of the motor and the size of your grow room are important considerations.

Benefits of Using an Inline Fan In Grow Tent

As a result of the fan being installed in a strategic place, the noise levels in the room that will be purified will be kept to a minimum. Reduced noise levels Additionally, if you have a well-insulated roof space, or if you prefer a silent model, the quiet fans will be beneficial to you. The length of the duct run – inline fans are intended to be used in conjunction with ducting. When compared to simple fans, this indicates that they can preserve a significant portion of the mentioned capabilities.

For example, if you wish to collect unpurified air from a grow tent, the length of the tube should be as short as it possibly can.

It’s simple to create many inlet or outlet locations with an inline fan by utilizing do-it-yourself approaches.

Components for Creating an Inline System

  • Ventilation system requires an internal vent, which serves as the point of extraction for the system, to function properly. Generally speaking, these vents and grills are available in a variety of forms, sizes, and colors to accommodate various characteristics of a grow room environment. It is preferable to use a short vent in order to limit the distance that air must travel
  • The use of ductwork to link the vent and the motor, as well as the connection of the motor to an external vent, may be required. There are many different types of ducting available, and the most suitable for grow rooms are the flexible varieties. Another kind is semi-rigid and insulated ducting, which are two of the most common options. Fan– A fan is the most important component of a grow tent system, and the fan you choose will be determined by a number of criteria. These considerations include the size of the space and the specific purposes for which the fan is intended. Calculator for exhaust fans– this tool may be used to determine the degree of extraction necessary for a system. It is preferable to have a fan with a diameter and length that are identical to the ducting that you will be using. It is important to remember that a fan can only be used with ducting that has a specified diameter. The amount of effort that the fan must do to cleanse the air will be reduced if the length of the fan is decreased. Lastly, an external vent can be installed on the exterior wall or on the roof, depending on the design of the building. Many alternatives are accessible in this area
  • For example, As an optional feature, you may also install a backdraft shutter in conjunction with the ductwork to assist avoid problems such as air flow backward. This will also assist to keep the system closed while the fan is not in use, which will be beneficial. Duct tape should be sufficient for holding everything in place. As a result, consider including work claps into the process.

System requires an internal vent to function as the system’s extraction point, which is located near the intake vent. Generally speaking, these vents and grills are available in a variety of forms, sizes, and colors to accommodate various components of a grow room’s environment. In order to decrease the distance that air must travel, it is best to use a short vent. The use of ductwork to link the vent and the motor, as well as the connection of the motor and an external vent, may be necessary.

  1. Another kind is semi-rigid and insulated ducting, which are two of the most common varieties.
  2. Which fan you choose will rely on several variables.
  3. It is possible to calculate the amount of extraction necessary for a system using an exhaust fan calculator.
  4. Please keep in mind that a fan may only be used with ducting that has a specified size.
  5. ; Exterior vent– This is the final component of the system, and it can be either an external wall vent or a roof vent.
  6. As an optional feature, you may also install a backdraft shutter in conjunction with the ductwork to assist avoid concerns such as air flow backward.

Furthermore, while the fan is not in operation, this will assist in keeping the system closed. Duct tape should be sufficient for holding everything in place. – As a result, consider including work claps into the procedure.

How Does A Ventilation System Affect Plants?

The primary purpose of a grow room is to give plants with the optimal growth environment, as opposed to what is accessible to them outside of the facility. As a result, this also entails delivering a continuous supply of fresh air that is high in CO2. Using a ventilation system, you can keep the CO2 levels in your grow room at the appropriate range for plant growth. As the quantity of CO2 in the air decreases, it becomes necessary to maintain a steady supply of fresh air from the outside. Plants are accustomed to growing in the elements and wind of the outdoors, where they are exposed to the elements.

The following facts will help you understand why these systems are so important for plant growth:

How to install an exhaust fan in a grow tent?

It is now necessary to set up the grow tent ventilation system at this phase. It’s the part that most people find difficult, yet it’s a straightforward operation. There are a variety of grow tent ventilation configurations to choose from. Having said that, it is advised that the fan and filter be hung within the tent for maximum effectiveness. If you only have tiny to medium-sized carbon filters, this is the most effective method. It contributes to the reduction of your expanding footprint by drawing air through the filter.

  • At the same time, it is a method of removing heated air from the upper area of the tent, which is beneficial.
  • This is not ideal since the filter may suck in extra warm air and direct it to the plants while the system is still in operation, which is not desirable.
  • In certain instances, though, laying the filter on the floor is the most practical solution to the problem.
  • While this strategy is advantageous in terms of saving space, it has significant disadvantages.
  • Furthermore, if the ventilation system is located outside the tent, it has the potential to enhance the amount of noise produced by the fan.
  • Before you begin, be certain that you have sufficient knowledge about the grow room’s climate and ventilation requirements.
  • The inline fan should be connected to one of the new ceiling bars in your grow area. Consider utilizing adjustable rope clip handles to suspend fans from the ceiling, which work nicely for this purpose. Either move the inline fan over so that it fits directly into the exhaust hole, or connect the inline fan to your ducting for further convenience. A convenient exhaust hole allows you to run the inline fun through and out of the machine for maximum ease. Hang the carbon scrubber — in most cases, it should come with handy ropes to make installation easier
  • Connect the carbon scrubber to the inline fan in such a way that the fan pulls air through the carbon scrubber. Consider utilizing ducting or just connecting them together if they are the same size as one another. Confirm that your components are the correct size and that they are arranged in the proper sequence. Through the bottom intake holes and up to the filter, the outside air will be passively drawn in from the surrounding environment. After then, the air is moved via the inline fan and out through the exhaust holes as a result of this innovative strategy.
See also:  How To Insulate A Tent For Winter Camping

The success of your grow is determined on the attention to detail. If you want to maximize your produce, you’ll need to educate yourself on the subject. How to install an inline duct fan in a grow tent is covered in this article. Read on to learn more. When you know how to properly do this operation, it will be simple to keep the air quality for your plants at an acceptable level. The use of an inline duct fan makes it simple to cleanse the air, and the addition of a carbon filter can improve the fan’s overall effectiveness.

Furthermore, you must take into account the remaining aspects and make certain that you “boil down to the minor particulars.” You may rest assured that your grow room will provide the highest possible output.

How to Hang Exhaust Fan in Grow Tent? The Ultimate Step By Step Guide

Who doesn’t appreciate the beauty of nature? I believe that everyone desires the freshness of the plants that surround them. As a result, gardening is growing increasingly popular on a daily basis. Plants, on the other hand, have their own set of requirements. Their need for a moderate wind and an inversion of the atmosphere, which may be difficult to achieve when cultivated inside, is understandable. So, what exactly are we looking for? What is the best way to hang an exhaust fan in a grow tent?

  1. After that, connect the carbon filter to the exhaust fan and check that the fan is in the proper location.
  2. Growing plants in grow tents necessitates the use of ventilation in this situation.
  3. However, in order to keep the grow tent and the plants within in good condition, you must meet the needs of the plants.
  4. You must ensure that your plants receive excellent quality airflow in order for them to grow properly.

How To Hang Exhaust Fan In Grow Tent? Step By Step Guide

The Best Way to Hang an Exhaust Fan in a Grow Tent Step-by-Step Instructions The extraction system for a grow tent is comprised of three basic steps: preparing the carbon filter, hanging the exhaust fan in the grow tent, and installing the ducting system in the grow tent.

Step 1 – Prepare The Carbon Filter

To begin, you must prepare the carbon filter by wetting it with water. In order to prepare for this, you must first uncover the item by removing the protective plastic coating. More information may be found at: How To Make A Carbon Air Filter For Your Grow Tent.

Step 2 – Get The Screws Back

There will be a few screws that hold the flange plate in place on the interior. You’ll have to remove those screws, lift the flange plate up, then reinstall the screws while keeping the plate in an upside-down position.

Step 3 – Cover The Plate

The dust cover should now be placed on top of the plate to protect it.

Step 4 – Connect The Carbon Filter With The Exhaust Fan

Now is the time to cover the plate with the dust cap.

Step 5 – Insert One Blade Into The Paper

Make use of your scissors to cut a single blade of one of them into the foil paper at the end of your ducting and then extend out the ducts once more around the perimeter.

Step 6 – Use Shearing MachineWire Cutter

Because the ducting pieces are moving in a spiral motion, it is impossible to separate them. As a result, the cut may come close to meeting the opposite side but will not be able to be separated. The shearing machine and wire cutter are required to separate them at the point where the foil is cut in order to do this.

Step 6 – Continue!

Now take the jack chain and cut it into two equal parts so that you may hang the filter and the exhaust fan with ducting from it.

Two portions will adhere to the ends of the duct on opposite sides. As previously noted, two different ducts will be utilized to link both the exhaust fan and the carbon filter, with two duct clips on either end of each duct.

Step 7 – Hung Together

Carbon filter and exhaust fan will be strung together outside the tent using a hanging rail before being linked in place. Slide one end of the tiny duct onto the flange plate, attach the duct clip, and tighten the screws with a screwdriver to ensure that it is secure.

Step 8 – Placement of the Exhaust Fan

Following that, an arrow will be painted on the surface of the exhaust fan to indicate the direction of airflow. Please make sure that this arrow points in the opposite direction of the carbon filter since the exhaust fan will suck the air that is coming from the carbon filter rather than blowing it through the filter. As a result, when installing the filter and exhaust fan in the grow tent, it is critical to pay attention to the direction of the fan and filter.

Step 9 – Final Check!

Slide the duct over the flange all the way around on the tiny end of the ducting and attach it with another duct clip at the other end. Then, with the last duct clip, tighten the ducting by sliding the long end over the opposite end of the ducting. It is recommended that this extraction system be positioned as high as possible in order for the air to move through it correctly. That is why it is advisable to build a grow tent ceiling rather than a floor. In order to hang the exhaust fan and filter outside the tent, you must raise them while they are suspended by the jack chain from the tent frame.

Because it will be more comfortable for you and you will not require any assistance, it is advised that you elevate them while they are not linked.

Support the exhaust fan with the straps attached to the filter and jack chain, and connect them to the hanging rail using the hanging rail connector.

I hope you were able to find the answer to the question “How to hang exhaust fan in grow tent?”

What Are The Effects of The Ventilation System On Plants?

The Influence of the Ventilation System on Plant Growth “How to hang exhaust fan in grow tent” is now something you know. But have you ever considered it? What are the ramifications of having that exhaust fan running? The fact that you are growing plants indoors means you must give them with the best environment possible in comparison to what they would receive if they were growing outside. Plants require a carbon dioxide-rich environment in order to develop properly. Plants can come in contact with an acceptable quantity of CO2 from the atmosphere while they are growing in the open air.

Plant development can be hindered in a variety of ways if this is not the case.

The exhaust fan installed in a grow tent allows us to give them with fresh air, but not too much or too little, which allows them to develop more quickly while also maintaining the humidity and temperature within the grow tent.

Although learning how to hang exhaust fan in grow tent is a difficult configuration to master since it necessitates the use of several methods and tips, as well as certain strategies, it is not difficult if you grasp the procedure completely.

The health of the plant will be improved as a result of this approach. It will aid with the removal of foul odors and excessive heat from within the grow tent, as well as the maintenance of the temperature essential for plant growth.

What Are The Benefits of Installing Exhaust Fan In Grow Tent?

“How to hang exhaust fan in grow tent” is now something you know. But have you ever considered it? What are the advantages of having an exhaust fan installed?

1. Reduction of Noise

The installation of an exhaust fan within the ceiling will assist you in reducing the amount of noise generated by the grow tent. You will benefit if you want your grow room to be silent and if it has an appropriate ceiling system on which you can put an exhaust fan, which is what I recommend.

2. Greater Capacity To Pass The Air

Hanging the exhaust fan in the grow tent will be beneficial because, with the help of this inline fan, you will be able to adjust the distance between the extraction point and the outlet ports. Air will be able to travel through more easily if the space between the two points is increased.

3. Making Several Outlets

The DIY technique allows you to create a large number of exits and intake locations. It is necessary to have these exits and intake points if you are employing a large grow area for your plants.

How Does The Exhaust Fan Work?

The Influence of the Ventilation System on Plant Growth It is something that is utilized to collect waste from a space outside of it that is referred to as an exhaust fan. For example, if you utilize an exhaust fan in your plant grow room, it will remove the foul odor, the air, the waste, and the humidity from the area outside of the tent. It is necessary to position the fan at a location where air may readily travel through the fan. The fan’s capacity to circulate air is determined by the height of the ceiling, the size of the space, and your ability to hang an exhaust fan in a grow tent in the appropriate manner.

You can learn more about the finest grow tent fans in 2022 by visiting our website.

What Are Components Do We Need To Install An Oscillating Fan In Grow Tent?

HVAC Exhaust Intake Fan, Low Noise, 4 inch Inline Duct Fan, 100 CFM, VIVOSUN Grounded Power Cord with an Extra Long Length of 5.5′ An input vent is required for the extraction system, which will also function as the extraction point in the grow tent. This vent will be used to evacuate air from the interior of your tent. Intake vents are available in a variety of shapes, sizes, and prices. You must select yours based on the size of your tent as well as your financial constraints. The smaller ones are preferable for usage since they limit the distance over which the air must travel.

2. Ducting

Suitable for heating, cooling, ventilation, and exhaust. AC Infinity Flexible 4-Inch Aluminum Ducting with Heavy Duty Four-Layer Protection, 25-Feet in Length When installing your extraction system, you will want ducting since hanging your fan and filter without it would be difficult to do. It is possible that ducting will be required to connect the internal vent to the motor and the motor to the exterior vent. There are several different forms of ducting, including flexible ducting, semi-rigid ducting, and insulated ducting.

3. Exhaust Fan

Aluminum High Speed 1620RPM, 940 CFM, IPower 12 Inch Shutter Exhaust Fan with Aluminum High Speed 1620RPM, 1-Pack, Silver Any extraction system would be incomplete without a fan. When you use a fan, it will draw the air out of the tent, purifying it and creating the ideal climate for growing your plants.

Additionally, there are several exhaust fans to pick from, but you must make an informed decision based on your requirements, the size of the space, and the intended usage of the fan.

4. Exhaust Fan Calculator

In order to calculate the extraction level required for your plants’ development in a grow tent, you will need an exhaust fan calculator. There is a straightforward calculation that may be used to quickly compute the extraction level of an exhaust fan. The formula is as follows: Fan volume (m3/hr) = Length(m) x Width(m) x Height(m) x number of air changes per hour Keep in mind that using ducting with the same diameter as your fan will improve the performance of your fan. Reduced diameter will result in a reduction in the quality of the job performed by the exhaust fan.

5. External Vent

With its 4′ hood, the Deflecto Supurr-Vent Louvered Outdoor Dryer Vent Cover (HS4W/18) provides a stylish and functional solution for drying clothes outside. Last but not least, the exterior vent is a critical component of your extraction system. You have the option of mounting the external vent on the exterior wall of your tent or through the hanging rail; the decision is entirely up to you. Another option is to install a backdraft shutter, which will decrease the backflow of air going through the system while simultaneously shutting off the system while the fan is not in use.

How To Hang Oscillating Fan In Grow Tent? Step By Step Guide

Hanging an oscillating fan in a grow tent is a simple process. Some gardeners may not wish to utilize ducting in conjunction with an exhaust fan and filter, and they may choose for oscillating fans rather than an exhaust fan with or without ducting since oscillating fans are less expensive than other types of exhaust fans. Oscillating fans are sometimes preferable to exhaust fans because they may oscillate, allowing for a pleasant breeze to be delivered without blowing on a specific location for an extended period of time.

I’ll demonstrate how to hang an oscillating fan in a grow tent, which I found to be both simple and time-consuming to put up in my experience.

Step 1 – Use Offset Flange

Use the offset flange black with screw holes to attach it to the tent pillars, which is included with the tent. You must connect two black flanges to the back wall of the tent, one to each of the cornerstones of the two corners of the back wall. Make an effort to get the flange as near to the roof as feasible. Then you’ll need to attach a long wood piece to the corner flanges, which will be held together with screws.

Step 2 – Secure The Oscillating Fan

You must fasten your oscillating fan with the wood piece in any location you deem necessary based on your requirements. Once you have completed the installation of the entire procedure, your extraction system will be ready for use. Now all you have to do is connect in the power cord, and your plants will be ready to move inside! If you follow the steps outlined above correctly, you can be confident that your plants will receive the proper airflow and atmosphere to thrive even more than they did previously.

Keep in mind that the technique of removing and installing your plants will determine whether or not your plants develop properly. The more precisely you hang your exhaust fan, the higher the quality of the airflow you will receive and the greater the yield you will receive from your tent will be.

What Are The Facts That You Have To Be Careful About While Hanging an Oscillating Fan In Grow Tent?

In order to properly hang an oscillating fan in a grow tent, there are a few considerations that must be taken into consideration. Never allow your fan to blow wind directly into or into your plants. It should only blow wind around the plants, not directly upon them. In addition, excessive wind will cause your plants to be clawed by the wind. When an excessive amount of airflow blows onto plants, it causes wind-burned, which causes the plants to claw. When you notice the clawed plants, you could assume that the clawing is the result of overwatering or underwatering, but the most likely reason will be over-winding of the plants.

See also:  When Was The First Tent Made

Be Careful About The Arrow

Keep an eye out for the arrow on the fan’s surface, which will tell you to the location where the exhaust fan and carbon filter should be installed. It is important not to direct the exhaust fan toward the carbon filter; otherwise, it will have a negative effect.

Take Care of The Oscillation

In the case of an oscillating fan, you should pay attention to whether or not the oscillation is functioning properly. A failure to do so will result in noise when the system is unable to oscillate normally.

Use An Exhaust Fan Calculator

The exhausting system must be checked using anexhaust fancalculator since the general temperature, humidity, airflow speed, and other variables are all aspects that must be considered in order for your plants to thrive properly in their environment.

Maintain The Diameter

Maintain the diameter of the ducting and the exhausting fan, since this is an important safety factor to consider.

Be Careful About The Cheap Ducting Fans

If you can afford better ducting fans, don’t get the cheap ones. They may claim to be able to blow a lot of air based on their CFM rate, but in reality, they don’t have nearly as much power to blow as you may expect. As a result, pick your fan carefully.

Choose As Your Room Size

You must select the duct, filter, and fans based on the size of your room or tent as well as the cost of each item. If you have a tiny tent, you should avoid purchasing a larger fan.

Ensure Better Placement

As much as feasible, hang your exhaust fan as close to the roof as possible since the higher up your exhaust fan is positioned, the more airflow you will obtain from it.

Check Regularly

Check the humidity level on a frequent basis since plants are constantly exhaling water vapor into the air, which can cause difficulties within the tent if the humidity level is too high.

Seal The System

It is necessary to seal the entire exhausting system after utilizing it since it is beneficial in increasing the efficiency of the system. When employing a carbon filter and an exhausting system, it is critical to ensure that the air is adequately ventilated from the grow room; otherwise, the air will flow through without being properly vented. The major function of the exhausting fan is to provide suction, which is very hard to achieve without a seal.

Make Sure There is No Leakage

Check for leaks at the junction between the filter and the fan if you’re using a carbon filter to ensure that no air is leaking through the filter.

Final Check!

Finally, cleaning your exhaust fan is critical because if it is not cleaned, it will not function correctly and the temperature inside the tent will rise, which will limit plant development.

Final Verdict

So, I hope you have a better understanding of how to hang an exhaust fan in a grow tent. Nevertheless, if you are experiencing difficulties, you may contact us by email. We can aid you in resolving the situation. Last updated on January 28, 2022 / Affiliate links included / Images sourced from the Amazon Product Advertising API

Buy them at Walmart, eBay, or Etsy

Shop on Etsy or eBay for ducting for your extraction system.

How to Ventilate Your Grow Space

You must have adequate ventilation in order for your plants to flourish. By giving your plants with fresh air from outside your grow tent, you are supplying them with CO2, which is necessary for their photosynthesis. Meanwhile, removing the air inside will help to keep the temperature and moisture buildup under control, avoiding mold and mildew from growing on your plants’ leaves and so hindering their ability to thrive. The extra benefit of refreshing the air within is that it helps to eliminate unpleasant smells.

Essential Grow Tent Parts

Assuming you have previously chosen or purchased your grow tent, this tutorial is equally useful if you are working in a grow room. This is a list of the three most important components that you’ll need to put together while building a ventilation system:

Inline Duct Fan (Active Exhaust Fan)

An inline duct fan, also known as an extractor fan, is a device that is used to exhaust hot and humid air from within a growing chamber or tent. Even little variations in temperature and humidity may have a significant impact on your chances of generating a fruitful harvest. Furthermore, unregulated heat and humidity cause poor growth circumstances, resulting in your plants being unable to absorb water or simply failing to make it through the day. The use of an inline duct fan in your grow room is essential for controlling the climate in your growing environment.

Using an active exhaust fan to draw in cooler air can assist you in maintaining a comfortable inside temperature level.

In ventilation systems with passive intake, inline duct fans also serve as a vacuum, drawing in new CO2 from the outside air and bringing it into the system.

Duct Tubes

Inline duct fans are attached to your grow room using ducting that is clamped or glued in place. The ducting serves as a channel to divert stagnant air away from your grow space. They are typically constructed of aluminum, although they may also be multilayered to provide additional protection against rips. Its size and bends have an impact on the performance of your inline duct fan, but we’ll get into that later.

Carbon Filter

A carbon filter will be required in order to prevent scents from traveling to your garage or closet. This device, which is also known as a carbon scrubber, removes the smell of plants from the air, capturing the odor and neutralizing it.

Carbon filters are a must-have for growers that have to cope with very strong odors. They are also used to trap pollen and spores, which helps to keep the air clean for farmers who suffer from allergies or respiratory problems such as asthma.

Typical Grow Tent Setups

There are several configurations for these components that may be used to create airflow into your grow environment. As a standard configuration, the fan and the filter are placed inside, which makes it easy to control while also dampening the noise from the fan. If air is being drawn out of your grow room, one or both of these components can be placed in any sequence within the ventilation chain. It is possible to customize your ventilation system in at least four different ways in order to meet your requirements.

The fan and/or filter can be placed outside of the grow tent in this situation.

Because heat rises to the top of the building, venting that hot air at that point will improve the efficiency of the ventilation process.

What Size Inline Fan do I Need?

There are many different sizes of grow areas, and each one requires a particular amount of airflow to be properly ventilated. It is critical for maximum plant growth that stale air within your grow room is exchanged with fresh air from the outside of your grow area. CFM (cubic feet per minute) is the unit of measurement for this number. To determine the quantity of airflow required for your grow room, first calculate the volume in cubic feet of the space. Most grow tent specifications are offered to you in inches; thus, you must convert the size of your space from inches to feet.

This will match the capacity of your grow room, and the needed airflow will be equal to this value in cubic feet per minute, or CFM, as well.

When the dimensions are added together, the result is 72 ft 3 in length.

Keep this amount handy since you’ll need to adjust it to account for the ducting, carbon filter, and any other accessories you decide to install.

Factoring in Accessories

In order to boost your base CFM, you must multiply it by the efficiency percentages of your accessories. Adding components to your grow room, including as ducting and carbon filters, may limit fan performance, which will have an impact on the fan size you require. When it comes to ducting, the quantity and sharpness of its bends play a role in determining the resistance to airflow. As a result, airflow decreases the longer it needs go, making a straighter ducting path more effective. The greater the sharpness of the curve, the greater the severity of the efficiency drop; a 30° bend reduces airflow by 20%, while a 90° bend reduces airflow by 60%!

  1. If you are utilizing LED grow lights, you must also take into consideration their heat production, which can raise your necessary CFM by as much as 50%.
  2. Because the efficiency of accessories on the market might vary substantially, you can utilize approximated efficiency percentages based on the type of component you are using.
  3. This amount is multiplied by the efficiency % of each component to arrive at the final result.
  4. Adding in the heat output of your grow lamp (about 50%) gives us a needed CFM of 249 cubic feet per minute.
  5. The following is a breakdown of this calculation: Multiplying your base CFM (72) by the percentages of ducting (20 percent), carbon filter (60 percent), silencer (20 percent), and grow light heat (50 percent) of your choosing will provide about the 249 CFM you require.
  6. This will let the fan to operate at lower speeds while remaining quieter, as well as providing additional area for future expand space system growth.

Look for inline duct fans that are powered by direct current (DC) fan motors, which are the quietest as compared to alternating current (AC) fan motors. PWM-controlled EC motors are also acceptable in terms of acoustic performance.

How to Manage Grow Space Noise

There is no question that you will hear some noise when employing a high-powered fan to air your grow environment. You wouldn’t want to spend an extended period of time in an area with excessive noise pollution or catch the attention of your neighbors. Fortunately, you can plan your component selection with noise reduction in mind, and you can take further steps to make your grow area as as quiet as possible. Making the decision to choose a fan with speed controls and a CFM rating that is 25 percent more than your minimal need will allow you to run the fan at lower speeds without compromising performance.

If you want to further muffle the sound of your active exhaust fan, you may attach a silencer to it, which will lessen the sound of the intake fan.

Grow Tent Ventilation Setup & Exhaust Guide

The importance of ventilation in your grow room cannot be overstated. As a result, poor ventilation is responsible for the majority of cannabis issues and leaf symptomatology. CO2 concentrations, temperature, humidity, and other factors are all taken into consideration. Cannabis plants are only able to survive under specific environmental conditions. It is at this point that grow tent ventilation and exhaust become important.

Why Your Grow Tent Ventilation Is So Important?

Your grow tent should attempt to emulate the growth conditions seen in nature. And the greater degree of control you have over those circumstances, the better. The most important thing to remember is that ventilation and exhaust are essential. Because of this, your grow tent’s environment is favourable to healthy development, vigorous plants, and abundant yields.

Keep The Perfect CO2 Level For Cannabis

Cannabis, like other plants, need carbon dioxide in order to live. However, when plants are enclosed in a small area, the CO2 in the air will soon be depleted and replaced by oxygen if there is insufficient circulation to the plants. So we’ll have to figure out how to restock it in some way. This means that the cold, fresh CO2-filled air should be drawn into your setup while the used air is expelled out the back.

Control Humidity And Excess Heat

Bud rot occurs as a result of inadequate ventilation. Cannabis plants grow in temperatures that humans would consider to be “comfortable.” That is to say, the temperature should be between 70 and 85 degrees Fahrenheit (or 20 and 30 degrees Celsius) throughout the vegetative stage. Dropping the temperature to roughly 65-80°F (18-26°C) when your plants are ready to blossom can result in higher yields and better-quality buds when your plants are ready to flower. In addition to adjusting the temperature of your grow tent, you should also consider controlling the humidity.

If you do not have an adequate exhaust system, you may find yourself with a moist grow room where mold and fungi will begin to thrive. Believe me when I say that you don’t want anything to do with white powdery mildew or bud rot.

Avoids Pests And Plant Diseases In Your Tent

Mold and fungus aren’t the only types of organisms that producers must be on the lookout for and avoid. Protect your plants against insect pests, which can thrive in stagnant air and damp soils, as well as from other environmental factors. It is difficult for spider mites and fungus gnats to fly when they are in well-ventilated areas. This means that if you have the proper fan and exhaust system, your plants will be lot safer from these insects.

Strengthen Stems

Finally, it’s vital to note that cannabis plants benefit from, and even require, a mild breeze in order to flourish at their ideal levels. This helps to give the stems a good exercise and keeps them from becoming too weak to sustain normal bud growth in the future. Your stems might get anemic if you don’t have a consistent wind blowing through your grow tent. This can lead to bowing. This, in turn, can hinder the leaves from absorbing enough light to effectively photosynthesize, resulting in a reduction in the ability of the plant to grow.

See also:  Which Tent To Buy For Family

Ways To Setup A Ventilation System In Your Grow Area

It may be necessary to make an investment and experiment in order to find the optimal ventilation for your ventilation system. Nonetheless, it is a feature of your system that will almost certainly pay off in the future. For begin, there are two different methods to configure your ventilation: passive intake or active intake.

Exhaust Fan With Passive Intake

Passive intake depends on negative pressure to generate passive airflow, which is why it is called passive. Quite simply, you have a fan that is pushing air out of the tent, but there is no fan pushing air in from the other side of the tent. As an alternative, you may install an intake hole that allows new air to enter the tent passively. You can have a single passive intake hole that is approximately three or four times the size of the exhaust hole, or you can have many passive intake holes.

This approach will cut energy use and will be the most effective for the majority of farmers.

Active Air Intake And Exhaust System

Alternatively, an active intake system employs a fan to actively suck air into your grow tent. So there aretwo fans working together. One to keep the air from inside the tent from blowing out, and another to keep the air from blowing in from outside the tent. When using this system, the size of the intake hole is less important. So if your grow tent has an intake hole that’s about the same size as your exhaust hole, your tent will lend itself well to an active intake system. Since most fans allow you to change their power,you may discover your own balance that allows you to attain the perfect temperature and humidityin your tent.

The Ultimate Ventilation Setup

The fundamental concept of exhaust systems remains constant. Keeping clean, fresh air coming in while venting out old and humid air is critical for the system to function properly. However, there are other accessories and pieces of equipment that you may incorporate into your setup.

The ideal ventilation design will not only keep your crop healthy, but it will also be discrete, resulting in the least amount of noise and aromas possible. I’m going to presume that your setup includes any or all of the following components:

  • The use of rope ratchets for securing your equipment
  • An exhaust fan (we’re going to use a passive intake for this project)
  • A carbon filter is used. Ducting and clamps are used. A deafening silencer
  • A fan that oscillates
  • Grow lights that are air cooled (most types of lights, such as LEDs, generate practically minimal heat and hence do not require inclusion in your ventilation system)

Ducting Your Fans And Accessories

The remainder of your equipment will be connected to your exhaust fan in the stages that follow this one, so pay attention. This will be accomplished by the use of aluminum ducting. Using flexible aluminum ducting, I have discovered that the right mix of price, adaptability, and convenience of installation may be achieved. However, insulated aluminum ducting will also work well if you want stronger duty ducting and have the necessary funds. Check for kinks and wrinkles and smooth them out if necessary to ensure peak performance.

You will have a less efficient system the longer and more roundabout your journey is.

Inline Exhaust Fan

After erecting your grow tent, the first thing you should do is connect your exhaust inline fan to it. However, you should avoid connecting anything to your power source until you’re ready to begin growing. Step inside your tent and attach your exhaust fan to the exhaust hole in the floor of your tent. Hanging your fan from the ceiling of your tent is one option. Connect the fan’s exit port directly to the exhaust hole, or duct it if you find it more comfortable, and then close the fan off completely.

Carbon Filter To Deal With Odor

Using your exhaust system to your advantage might let you develop discreetly if you like. It is possible to keep the scent of cannabis out of your home by using a carbon filter. Your carbon filter is something that has to be considered while configuring your exhaust system. In order for the air from your grow tent to be expelled outdoors, it first has to travel through your filter. Many growers choose to employ the simplest possible configuration, which is to hang the carbon filter inside the tent.

In this manner, the air will first pass through the carbon filter, after which the exhaust fan will expel the filtered air to an outside environment (first picture).

In the event that you do this correctly, the only location where you’ll be able to smell cannabis will be when you’re inside your grow tent.

Silencer For Extra Stealth

When installing a silencer, it is best to position it immediately after the fan; but, if necessary, you may place it farther down the ducting. It works by muffleing the air coming from the exhaust, resulting in significantly less noise. And they are quite effective. My tent, which is located within the home, has a suppressor placed in it, and the decrease in noise is incredible. I highly recommend it.

It also alters the sound style; it moves from being a dreadful whining to a pleasant swooshing that sounds more like wind as a result of the shift in volume. Always keep in mind that it will reduce airflow, so you’ll need to account for it when calculating CFM requirements (more on that below).

Connecting An Air-Cooled Reflector (Mostly for HID grow lights)

If you’re utilizing high-intensity discharge (HID) grow lights, it’s extremely probable that your hooded fixture can accommodate ducting. You’ll need to have direct airflow passing through the light’s reflector in order for it to work properly. This will assist you in keeping the temperatures down as well as the light bulbs cool, which is important because HID lights generate a lot of heat. Depending on your reflector and how many additional accessories you have, this can add a significant amount of complexity to your setup.

Starting with your CO2 filter and working your way up to your reflector is a good idea.

Sealing Your Grow Tent To Create Suction

A sealed grow tent guarantees that only air enters through the intake hole and only leaves exit via the exhaust fan when the tent is closed. Your exhaust system will be prone to air leakage and will be extremely inefficient if the seals are not properly installed. Sealing provides a separate environment, allowing you to regulate temperature, humidity, and CO2 levels independently. Additionally, it guarantees that your exhaust system is running at maximum efficiency. Your exhaust fan will generate negative air pressure as a result of reducing air leakage, allowing fresh air to enter via the intake hole.

When used in conjunction with a carbon filter, this will further reduce the likelihood of cannabis scents penetrating your house.

However, if you have tears or pinholes, you may use anything from duct tape to Black RTV Silicone to close them up again.

Check For Air Leaks

To check for air leaks, start by turning on your system and closing your tent from the inside outward. Moving an incense stick about the interior of your tent and observing its behavior can give you a better understanding of its behavior. If the smoke rises straight up into the air, the air is exactly where it should be. To finish, take the incense stick outside the tent and position it near to the intake hole on the other side. If the smoke snakes towards the intake, this is a strong indication that you have accomplished effective sealing and negative pressure in the engine.

Oscillating Fans

Oscillating fans are both inexpensive and quite effective. The process of blowing and spreading air uniformly within your grow tent, while also ensuring that the wind is powerful enough to keep the stems of your plants strong You may use floor fans that are placed in a corner of your room or grow tent fans that are much smaller and clip on to the poles of your tent to keep the heat out. It’s possible to hang it or place it in your room if you’re a bit of a do-it-yourselfer and you have a fan laying around.

The number of fans you need will depend on the size of your grow tent and the size of the fans you use.

You may just require one or you may require several. There is no straightforward method of determining how many you require. However, attempt to position the fans in such a way that your entire crop receives some air circulation.

How To Calculate CFM For Exhaust Fans

To properly ventilate your grow tent, you must first determine how much fresh air is required in order to guarantee that your plants develop in a healthy manner. You may determine the appropriate Cubic Feet per Minute (CFM) required to ventilate your tent using a formula, which is provided below.

1. First let’s find out your grow tent’s volume

While the height of your grow tent may vary, we’ll use a 4×4 grow tent with a pretty standard 8′ height as an example. (width) * (depth) * (height) = 128 ft 3 (width * depth * height)

2. Calculating Base CFM

The amount of air in your grow tent should be replenished by your inline fans once every two to three minutes, at the absolute least. The following is the formula: 128 feet/3 minutes =64 CFMB However, the temperature and humidity of the surrounding environment must be taken into consideration. If the room from which you’re obtaining the air is excessively hot, add an additional 20% to your calculations. And if you’re dealing with high humidity, increase the percentage by another 40%. In a hot and humid environment like mine, the result might be something like this: 64 (cfm) multiplied by 1.4 (humidity) multiplied by 1.2 (warm climate) Equals 108 Base CFM This implies that in order to adequately ventilate your 128ft 3grow tent, you must exchange 108 cubic feet of air every minute.

3. Factoring In Accessories

Now that you’ve calculated your basic CFM, you’ll need to add in your accessories, which may include ducting, grow lights, and a carbon filter or silencer, among others (where necessary). All of these factors might have an impact on how hard your fan has to work in order to create the ideal growth conditions. For example, any abrupt bends in your ducting will drastically limit the efficiency of the airflow through the system. A 90-degree curve has the potential to restrict airflow by up to 60%!

If you’re using a charcoal filter to eliminate scents emanating from your tent, add additional 60 percent to your calculations.

Accessories Effect on CFM
LED grow lights 20%
HID grow lights 50%
CO2 filter 60%
Silencer 20%
Ducting 30º Bend 20%
Ducting 90º Bend 60%

If we only had a few bends, a few LED grow lights, and a CO2 filter, we’d be in business. In the end, our CFM formula would be: 108 (base) * 1.2 (lights) * 1.6 (filter) * 1.9 (ducting) = 394 Total CFM Required You will now need to purchase an exhaust fan that can produce this amount of Cubic Feet of air per Minute, depending on the size of your grow tent and the accessories you will be using. Check out the greatest 6′′ inline fans that are capable of performing admirably.

Other Air Flow And Ventilation Tips

It is reasonable to expect some noise from your grow tent because it requires a powerful fan to air it. It is possible to reduce this so that your growth is more subtle and unobtrusive, but it is not recommended. Choose a fan with variable speed settings and a CFM rating that is 25 percent more than your requirements; this will allow you to run it at a reduced speed and so reduce noise.

Furthermore, the majority of inline fan types are equipped with noise-reducing capabilities. However, as previously said, you may also connect a silencer to your fan, which will reduce the noise it makes.

CO2 Injection To Increase Yields

Injection of CO2 into a grow tent Plants, as most growers are aware, “breathe out” oxygen while “absorbing” Carbon Dioxide (CO2). While plants do not have lungs, they do have hundreds of small holes on their surfaces known as stomata, which allow them to collect CO2 from the surrounding environment. In contrast to us, they require more carbon dioxide in the air than oxygen in order to maintain optimum health. This invisible gas is essential to the process of photosynthesis, and your plants will “suffocate” and die if they do not receive enough of it.

  • It may even be possible to make your plants more resistant to heat and light by doing so.
  • Trying to get the most out of every situation.
  • Even novices and enthusiasts may get incredible yields in the absence of this.
  • Check out this professional tutorial from CO2Meter for more information on how to get started.

Grow Room Air Conditioner

Despite the fact that it may be deemed unnecessary, an air conditioner may be a worthwhile purchase if you are coping with extreme heat. This is especially true for larger venues. It might be an excellent method of avoiding excessive heat and exerting the greatest amount of control over your temperature. Whether you’re growing in the heat of summer or the cold of winter, your plants will benefit from the right cool breeze and provide you with strong and consistent harvests. You have the option of putting your air conditioning unit on the ground.

It’s also a good idea to put it near an outlet so that any remaining water can be easily drained.

According to this calculator, 5,000 BTU is sufficient for grow tents measuring up to 4x4x8 feet in size.

Final Thoughts

In conclusion, ventilation is extremely crucial to the health and production of your plants, as you can see. The more the degree to which airflow is left to chance, the greater the likelihood that you will be disappointed with poor yields. There are several methods through which you may exercise control over the ventilation of your grow tent in order to achieve maximum yields. Hopefully, you were able to choose one that best meets your needs. And remember to go back to this post anytime you have any questions.

Leave a Comment

Your email address will not be published. Required fields are marked *