How To Fold Up A Tent

How to Pack a Tent

Upstate New York: Round Pole Wedding Tent $2,982 for a 100-person ceremony and cocktail hour.

Step 1: Packing Up the Fly

As shown in the second figure, straighten up the fly and then fold it lengthwise so that the exterior (the parts with guy ropes) is inside of the fold as shown in the first picture. With a little skill and the help of two persons, it is quite simple to sweep the fly off the built tent (after removing/unfastening all of the supports) and fold it lengthwise.

Step 2: Folding the Fly

Make sure each end touches the nearest support before continuing to fold in toward the center. – One you’ve reached the middle, fold it over once more to seal it. If this stage is completed correctly, the fly should be the same width as any of the folded poles, as seen in the final figure. If this step is completed incorrectly,

Step 3: Rolling Up the Fly

Fold each end so that it touches the nearest supports, and then continue to fold in toward the center. To complete the fold, fold it over one more to reach the center. If this stage is completed successfully, the fly should be the same width as any of the folded poles, as seen in the last figure. If not, repeat the process.

Step 4: The Main Tent

The large tent has been set up in such a way that it appears to have been built. The entrance door is located at the top of the photo, closest to the bins. Make sure all zips, including those on the windows, are closed.

Step 5: Adjusting the Roof

Pull the canopy so that it lays level and is not too bunched up, using the center roof mounts, which can be either clips or tubes for the support rods, to do this. As indicated in the second photo, make sure the front door is flat and that any extra hangs over the back door. If you have a dome tent that does not have a vestibule, work in a circular motion, pulling each side tight before ending with the front of the tent. It is really beneficial to have the tent still tied down at this point.

Step 6: Folding the Vestibule

Pull the canopy so that it lays level and is not too bunched up, using the center roof mounts, which can be either clips or tubes for the support rods. As indicated in the second photo, make sure the front door is flat and that any extra hangs over the back door. Work in a circular motion to tighten each side of the dome tent before finishing with the front if your dome tent does not have a vestibule. To have the tent still tied down at this point is quite beneficial.

Step 7: Folding the Tent

Pull the canopy so that it lays level and is not too bunched up using the center roof mounts, which can be either clips or tubes for the support rods. As seen in the second photo, make sure the front door is flat and the excess is extending over the back door. You can work in a circular motion to tighten each side of the dome tent before finishing with the front if your tent does not have a vestibule. It is really beneficial to have the tent still in place at this point.

Step 8: Putting It All Together

Pull the canopy so that it lays level and isn’t too bunched up using the center roof mounts, which can be either clips or tubes for the support rods.

In the second shot, notice how the front door is flat, with the excess extending over the back door. If you have a dome tent without a vestibule, work in a circular motion, pulling each side tight before completing with the front. It is quite beneficial to have the tent staked out at this point.

Step 9: Put It in the Bag and Do It Up

Pull the canopy so that it lays level and is not too bunched up, using the center roof mounts, which can be either clips or tubes for the support rods, to do this. As indicated in the second photo, make sure the front door is flat and that any extra hangs over the back door. If you have a dome tent that does not have a vestibule, work in a circular motion, pulling each side tight before ending with the front of the tent. It is really beneficial to have the tent still tied down at this point.

Be the First to Share

Putting the tent together is actually rather simple. Particularly popular are dome tents. Furthermore, getting them down is not too difficult. Putting them back in the bag, on the other hand, is a another matter. In this post, you’ll learn how to fold a tent like a pro – and how to put it back in its bag, just as you did when you first got it!

How to Fold a Tent Like a Boss

You’ve been out in the woods for some days now. You have become one with nature. You can’t recall the last time you cleaned your hair, and you get the distinct impression that you might want to stay here indefinitely. But then you remember the hair washing and how lovely it would be to take a hot shower instead. In addition, you have work the next day. Your food supplies have been reduced to a can of baked beans and an onion, among other things. It’s past time to leave. The tent remains in place as you pack up camp, fill up the garbage bags, and load the car.

Because it is the most inconvenient item to take apart.

No need to be concerned any longer, since I’m here to tell you that it doesn’t have to be this difficult.

The following are the four sections of this post:

  1. Tent Folding 101 (skip to the part you’re interested in)
  2. The proper way to fold a dome tent (go to the next step)
  3. Instructions on how to fold a cabin tent (go to the next section)
  4. 13 recommendations for taking care of your tent (skip to section)

Jump to the section on Tent Folding 101. To learn how to fold a dome tent, go to the next section. To learn how to fold a cabin tent, please continue reading. 13 recommendations for taking care of your tent (skip to the next paragraph);

How to Fold a Tent: 5 Steps

Tent Folding 101 (skip to the next section); To learn how to fold a dome tent, go to the next section. To learn how to fold a cabin tent, go to the next section. 13 recommendations for taking care of your tent (go to the next section);

  1. Before packing the tent, clean it well and check that it is completely dry. The tent will become moldy if it is left damp for an extended period of time. If you must pack anything damp, make sure to unpack it as soon as you get at your destination and dry it out immediately. To make the tent fit into the bag, it must be folded down somewhat smaller than the bag. Tent poles should be rolled within the tent. Make use of a knot to keep the tent tightly coiled
  2. Remove bumps and wrinkles to reduce the amount of superfluous mass

How to Fold a Dome Tent: 11 Steps

Before packing the tent, make sure everything is completely dry and clean. The tent will become moldy if it is exposed to water for an extended period of time. As a precaution, if you must transport it damp, make certain that it is unpacked immediately upon arrival at your destination and thoroughly dried. The tent must be folded in such a way that it is slightly smaller in size than the bag The tent poles should be rolled into the tent. Using a tie, secure the tent’s roll-up shape. Reduce the presence of lumps and wrinkles in order to reduce the amount of extra bulk.

  1. Make sure the tent is clean: Empty the tent of all dirt, food, and other possessions to ensure that the tent is clean and clear of obstructions
  2. Remove any tent pegs that may have fallen to the ground: Ascertain that all of your tent pegs have been gathered and placed in their respective bags, and then place them in the pole bag. Remove the fly poles from the ground: Remove any poles from the flysheet and fold them up into the pole bag before continuing. Inside the tent, lay the flysheet out as follows: Check to see that the flysheet is dry and clean before laying it down as flat as possible on the inner floor of the tent
  3. Open all of the tent doors at the same time: This will guarantee that any air trapped within the tent will be released rather than trapped inside the tent. Take down all of the tent poles: Remove all of the poles from the ground and place them folded back into the pole bag. Fold the main tent as follows: Make sure that all of the tent’s components are contained within the primary perimeter. By now, you should have a square that contains both the flysheet and the tent structure itself. In a squat position, lean the pole bag against the edge of the tent, about equal lengths from either end. This will serve as a point of reference for you when determining where to fold your tent. Take one edge and fold it in so that it is in line with the edge of the tent pole bag. Repeat with the other edge. Once you’ve completed one edge, repeat the process on the other so that you have a long rectangular form that is no broader than the pole bag. Remove all of the air and flatten down the resultant shape: Ensure that the tent is as flat and neatly folded as possible by going over it and eliminating any wrinkles or air pockets. Incorporate the pole bag into the tent as follows: Starting at one of the tent’s ends, place the pole bag and begin to wrap the canvas up around it as tightly as you possibly can. Please make sure that you are rolling it in a straight line so that one end doesn’t end up being thicker than the other. You can utilize your body weight to roll tightly and eliminate air as you go
  4. However, this is not recommended. To bring everything together, say the following: Tie two lengths of rope around each end of the cylinder once it has been properly rolled (you should have some from original packing). The Australian gentleman proposes making loops at one end of each length of rope, then looping the other end through and pulling to give the rope more stiffness. Put everything in one place! It’s finished, just like that! The tent should be able to fit inside the bag without any difficulty

How to Fold a Cabin Tent: 10 Steps

Make sure your tent is clean: Empty the tent of all dirt, food, and other things to ensure that the tent is clean and clear of obstructions. Dispose of any tent pegs that may have fallen to the ground. Inspect to see that all of your tent pegs have been gathered and placed in their respective bags, and then place them in the pole bag. The fly poles should be taken down. Any poles should be taken out of the flysheet and folded into the pole bag. Inside the tent, lay the flysheet out as follows.

  1. The tent doors should be opened from all directions: Any air trapped within the tent will be released as a result of this, and no air will be trapped outside.
  2. Remove all of the poles and place them back in the pole bag, folded up.
  3. By now, you should have a square that includes both the flysheet and the tent structure.
  4. Having a reference point for where to fold your tent will be really helpful.
  5. Repeat with the other edge and fold it in again.
  6. Remove all of the air and smooth down the resultant surface area: Examine the tent, eliminating any wrinkles or air pockets, and overall ensuring that it is as flat and neatly folded as possible.
  7. Make sure you’re rolling it in a straight line so that one end doesn’t get thicker or wider than the other end.
  8. In order to bring everything together, Tie two strands of rope around each end of the cylinder once it has been neatly rolled (you should have some from original packing).
  9. Make a mental note to put everything away.
  10. If all goes according to plan, the tent should fit inside the bag without any difficulty.
  1. Tent cleaning: Empty the tent of any dirt, food, and other things to ensure that the tent is clean and uncluttered
  2. Remove any tent pegs that may have been left on the ground: Inspect to see that all of your tent pegs have been gathered and placed in their respective bags, and then place them in the pole bag
  3. Take down the fly poles: Remove any poles from the flysheet and place them in the pole bag
  4. Place the flysheet inside the tent as follows: Lay the flysheet out on the inner floor of the tent as flat as possible, making sure it is dry and clean. All of the tent doors should be opened: Any air trapped within the tent will be released as a result of this, preventing it from getting trapped. Remove all of the tent poles from the ground: Remove all of the poles from the ground and place them folded back inside the pole bag
  5. Fold the main tent in half as follows: Make certain that all of the tent’s components are contained within the primary perimeter. By now, you should have a square that includes both the flysheet and the tent structure itself. Place the pole bag against the edge of the tent at approximately equal distances from either end. This will serve as a guideline for where you should fold your tent. Take one edge and fold it in so that the fold is in line with the edge of the tent pole bag. Repeat with the other edge and fold it in. Once you’ve completed one edge, repeat the process on the other so that you have a long rectangular form that is no broader than the pole bag
  6. Remove all of the air and flatten the surface: Ensure that the tent is as flat and neatly folded as possible by going over it and eliminating any wrinkles or air pockets
  7. Insert the pole bag into the tent as follows: Starting at one of the tent’s ends, place the pole bag and begin rolling the canvas up around it as tightly as you can. Make sure you are rolling it in a straight line so that one end does not grow thicker than the other. You can use your body weight to roll tight and eliminate air as you go
  8. However, this is not recommended. To bring it all together, say this: Tie two pieces of rope around each end of the cylinder once it has been properly rolled up (you should have some from original packing). For added firmness, the Aussie bloke proposes placing loops at one end of each length of rope and then looping the other end through and pulling on it. Put everything in a bag! It’s finished, everything done! The tent should be able to be stowed in the suitcase without any difficulty

Do you require a tent? See our Ultimate Buyers Guide to the Best Family Camping Tents for more information.

13 Tent Care Tips

A tent is required. Consult our comprehensive guide on the Best Family Camping Tents for further information.

  1. Are you in need of a tent? Consult our comprehensive guide to the Best Family Camping Tents for more information.

Thank you to REI for providing some of the ideas for these suggestions. Additional reading: How to properly stake a tent

Your Turn

You should be able to go camping and amaze all of your friends with your tent folding abilities now that you have the information. There is nothing better than getting to the conclusion of a pleasant weekend knowing that you will not be forced to fight with your tent for an hour in order to get it back into its bag.

Now you can walk out into the wilderness (and inside whatever tent you may have) with the confidence that you will be able to get it back into its small, tiny bag if need be.

How To Roll Up A Tent . And Get it Back In The Bag

Getting a tent back into its bag, complete with tent poles, inner tents, and other accessories, may be difficult. Here’s a simple technique for putting your tent away and completing that nearly difficult process in one piece. So, to summarize.

  1. Fold the tent so that it is slightly thinner than the bag in which it is stored. It’s important to remember that your tent should be completely dry before storing it up. If not, you may need to take it outside to dry when you get home. Bring the tent poles to the table. These are often packaged in their own bag. Place the tent poles at one end of the tent and roll the tent up around the poles to close the tent up completely. This should be kept as tight as possible. The weight of the poles aids in the expulsion of the air. Leaving vents and doors open will aid in the removal of the trapped air. Depending on the form of your tent, begin by rolling the end that is furthest away from the entryway
  2. You should finish up with a tent that is beautifully rolled and small enough to go back into its bag. If you have a piece of ribbon or rope, wrap it around the tent to keep it from unwinding.
See also:  What Is A Roof Tent

Fold the tent so that it is slightly thinner than the bag in which it is stored. It’s important to remember that your tent should be completely dry before packing it up and moving. You may have to hang it up to dry when you reach home if this is the case. Bring the tent poles to the front of the building. A bag is frequently included with them. Place the tent poles at one end of the tent and roll the tent up around the poles to close the tent up properly. A good amount of tension should be maintained here.

Keep windows and doors open to allow the air to circulate more effectively.

Keep the tent from unrolling by tying it together with ribbon or rope if you have some.

Get the Family Camping Planner

You will receive the family camping planner once you have entered your name and email address.

How to Fold a Tent: A Complete Step-by-Step DIY Guide

You will receive the family camping planner after providing your name and email address.

  • Washing rags for use in cleaning the tent
  • A sleeping bag for the night
  • The twine that will be used to bind the tent together

Steps to effectively folding a camping tent

Camping necessitates the transportation of a large number of items for usage in the wild. They are usually kept in the tent when not being used. As a result, the first step will be to remove everything from the tent and then, using a clean wet rag, clean the interior of the tent’s interior. Remove any food particles or anything else that might serve as a breeding ground for mould by cleaning the area thoroughly. After you are finished cleaning the inside of the tent, move on to the outside of the tent and repeat the process.

It is preferable to let it air dry.

Make assured that everything is completely dry before proceeding.

Remove the stakes or pins holding the shelter

Campers must pack several items that will be put to use in the forest while on their journey. They are usually stored in the tent when camping. Consequently, the first step will be to remove everything from the tent and then, using a clean wet rag, wipe the inside of the tent’s walls and floor. Remove any food particles or anything else that might serve as a breeding ground for mould by cleaning the area completely. After you’ve finished constructing the inside of the tent, move on to the outside and repeat the process there.

This should be dried outside as much as possible.

(See also: Double-check to make sure it’s completely dry before proceeding.

Remove the poles

Camping necessitates the transport of a large number of items for usage in the wild. They are usually maintained in the tent. As a result, the first step will be to remove everything from the tent and then wipe the interior of the tent with a clean, moist towel. Remove any food particles or anything else that might serve as a breeding environment for mold. After you are finished cleaning the inside of the tent, proceed to the outside of the tent and repeat the process.

Allow plenty of time for the tent to dry before you begin folding it. It is preferable to allow it to air dry. It is not acceptable to fold a damp or dump tent. Check to see sure it is completely dry.

Shake up the camping tent

Cleaning up the tent may not always imply that you are finished. As amusing and strange as it may sound, you must pick up your tent and shake it well before using it. The only reason for doing this is to clear away any debris that may have accumulated on the tent.

Make the tent flat

It’s possible that cleaning up the tent doesn’t indicate you’re finished. Although it may seem absurd and strange, you must take up your tent and shake it vigorously before continuing. Only debris that may have accumulated on the tent will be removed in this manner.

Fold up the tent

You must be really focused at this phase in order to fold the tent properly and into extremely little pieces. To begin, elevate the outside pieces of the tent and bring them closer to the center of the tent. The folds should be positioned in a straight line from top to bottom. Important to remember is that you should fold the tent longitudinally rather than widthways. When folding the tent, be sure that the tent’s door is on top of the fold. Fold the tent so that it is just a fraction of its original width dimension when it is not in use.

In order to avoid this, you must pat the inside of your already folded tent to verify that no air is trapped within it.

Pack up the fly

In order to do this stage successfully, you must be extremely focused on folding the tent properly and into extremely little pieces. For starters, begin by lifting and bringing the tent’s outer components closer to its center. Straight lines should be drawn between the folds. You should fold the tent lengthwise, since this is a crucial consideration. When folding the tent, make sure that the tent’s door is on the top of the fold and not underneath. Using one-quarter of the tent’s original width, fold the tent in half again.

This may be avoided by patting your previously folded tent to ensure that air does not become trapped within it.

Folding the fly

With this stage, you must be really focused on folding the tent correctly and into extremely little pieces. To begin, lift the outer pieces of the tent towards the center of the tent, starting at the corners. The folds should be positioned in a straight line from one another. One crucial tip to remember is that you should fold the tent longitudinally rather than widthwise. When folding the tent, be sure that the door of the tent is on top of the fold. Fold the tent so that it is a fraction of its original width dimension.

In order to avoid this, you must pat the interior of your already folded tent to ensure that air does not become trapped within.

Put everything together

Place everything out in front of the tent, starting with the fly nearest to you and working your way out to the tent poles, pegs, and anything else that is farthest away. Before you do anything, you must completely roll in the fly, insert the tent poles, and roll it again. Put the pegs back in and roll it up once more.

Incorporate any remaining ingredients and roll till the finish, tying it properly at the end. When rolling the tent, make sure to roll it firmly since allowing too much air inside the tent can cause issues when folding, as the tent may not fit into the bag.

Put the tent in the bag

Place everything out in front of the tent, starting with the fly nearest to you and working your way out to the tent poles, pegs, and anything else you want to be the furthest away. Firstly, you must completely roll in the fly, insert the tent poles, then roll it one more before moving on. Once more, secure the pegs with the ties. Continue to roll until the finish is reached and knot it neatly if there is anything else. When rolling the tent, make sure to roll it firmly since allowing too much air inside the tent can cause issues when folding, as the tent will not fit into the bag.

Folding a Cabin Tent

A cabin tent is fairly large and can accommodate groups of up to ten individuals. While putting it together may not be difficult, getting it inside the tent bag is a different story entirely. If it is not folded correctly, it may not fit properly in the bag. Several factors should be taken into consideration when folding a cabin tent:

  • It is possible to put more than 10 people in a cabin tent, which is rather large. While putting it together may not be difficult, getting it inside the tent bag is a different story altogether. It may not fit inside the bag if it is not correctly folded. Before you fold a cabin tent, keep the following things in mind:

Folding a Backpacking Camping Tent

This tent is a favorite of individuals who want to travel light while camping. So that’s how you fold a backpacker camping tent, step by step.

  • The tent should be cleaned and dried thoroughly to guarantee there is no mold growth and that it does not have a foul smell
  • Whether it’s pins or stakes, Remove anything that has been used to secure the tent to the ground so that it may be moved. It is important to keep the pins and stakes in a different location from the tent bag in order to avoid ruining the fabric of the tent. Fold the tent poles after removing them from the loops. As long as the poles can be tied together or placed in a different bag all together, they should be OK
  • Otherwise, they should be stored separately. The tent should be shaken to get rid of any remaining dirt and to straighten the cloth. Place the tent on the ground so that the entryway is towards the top of the structure. Fold the bag in half starting from the sides and working your way towards the middle. Check to see that there is no air trapped in the folds or lumps of fabric. Roll inside the tent starting from the spot that is furthest away from the entrance. Finally, tie it securely and place it in the tent bag to finish it.

Folding a Dome Shaped Tent

In the event that you want a dome-shaped tent, here are some tips on how to fold this sort of tent.

  • Pack the flysheet in the trunk of the car. Before you do anything, make sure the flysheet is straight. Fold the fly in half lengthwise, with the outer section of the fly folded within the fly. Fold the fly in half lengthwise again, this time with the outside section facing inside. If you want to do it well, you can utilize a second hand. Fold the fly in half. Retuck the fly’s ends to the nearest pole, then collect the fly’s ends towards the center and fold it in once more. Repeat with the other fly. If everything is done correctly, the flysheet of each pole should be the same width. The fly is being rolled up. Begin by working your way up to the top of the fly, concentrating on the lightest section of it. Roll it up firmly and secure it with a knot. When folding the tent, the tighter the fly is, the simpler it is to fit it into the bag. The tent should be spread in the same manner as it was built. Make certain that all zippers are completed
  • Make the necessary adjustments to the roof part. The center roof mounts will serve as excellent support rods for the structure. Pulling the canopy can help to ensure that it is completely flat. Don’t be concerned about the surplus fabric. Simply place it over the area of the rear entrance and fold the vestibule down to the floor. Fold the vestibule so that it lies over the body of the tent, with the top portion of the vestibule resting on top. If your tent does not have a vestibule, you may skip this step and just fold the tent. Fold each edge of the tent towards the center, then fold it in half again to reduce the size of the tent to a quarter of its original size
  • Gather everything together. Place everything on the front section of the tent by first placing the fly sheet, poles, pegs, and any other items that you want to use in the tent. Adding one element at a time, rolling once, adding another and rolling again, and lastly rolling the end of the tent and tying it properly is the best way to go about this process. The tent should be rolled extremely tightly to eliminate unwanted wrinkles while folding and rolling, since any extra air will cause the tent to not fit in the bag.

Useful Tips When Folding a Tent

Roll up your tarp and head to the beach. Before you do anything, make sure the flysheet is straight! Fold the fly in half lengthwise, with the outer section of the fly folded within the center. Make another longitudinal fold in the fly with the outside section facing inside. Repeat the process for the second fold. To accomplish this properly, you can utilize a second hand. Using the fly, fold it in half. Retuck the fly’s ends to the nearest pole, then collect the ends of the fly towards the center and fold it in once more.

  • The flysheet of each pole should be the same width if the job is done properly.
  • Begin by working your way up to the top of the fly, concentrating on the lightest section.
  • Tent folding is made simpler by tying the fly as tightly as possible before putting it in the bag.
  • Double-check that all zippers are properly installed; Make the necessary adjustments to the roof component of the structure.
  • The cover should be pulled taut to ensure that it is completely flat.
  • Lay it over the back door area and fold the vestibule.
  • To set up a vestibule, fold it so that it lies over the body of the tent, with the top section of the tent laying on top of the bottom part.
  • Fold each side of the tent towards the center, then fold it in half again to reduce the size of the tent to a quarter of its original size; pack it all together.
  • Adding one element at a time, rolling once, adding another and rolling again, and lastly rolling the tent’s end and tying it properly is the finest method to go about this process.

The tent should be rolled extremely tightly to eliminate unwanted wrinkles while folding and rolling since additional air will cause the tent to not fit in the bag.

  • Tents are available in a variety of sizes and from a variety of companies. It is also essential that you consult to your user’s handbook for instructions and information pertaining to your specific tent, in addition to the information provided on this page. Every tent features distinct fold lines that are visible at the time of purchasing. While folding your tent, make an effort to navigate your way through the creases and, if possible, discover the fold lines. Using this method will save you a lot of hassle and time. Clean your tent thoroughly and allow it to air dry to ensure a longer lifespan. Avoid lumps and creases that aren’t required in order to avoid gaining excessive weight. Make certain that no sharp things, such as pins, are stored with your tent in order to protect the fabric.

Importance of Knowing How to Pack Away a Tent

Those searching for something that can be put up quickly and will keep them comfortable during the night while they are out in the jungle will almost probably opt for something that will cost a significant amount of money. Tents are quite costly, and learning how to properly care for them will save you a significant amount of money in the long run. A tent that has not been properly tacked down is typically heavier and bulkier due to the fact that the weight has not been evenly distributed. Knowing how to pack away your tent will make it much easier to transport it whether you are trekking or going hiking.

Check out our study of the best ultralight tent for additional information on your alternatives.

Final thoughts

All campers must be able to pitch a tent, which is an essential skill. Spending the night in the woods with a bunch of friends is a great way to spend the evening. While the experience may not have been as warm and cozy as you would have liked, the memories made are ones that should be treasured. A large majority of campers are familiar with the feeling of having to pack up their tent. Typically, people collapse the tent and roll it inside the tent bag, however this never results in the tent bag fitting properly.

Check out our simple instructions on how to create a DIY camping tent for inspiration if you want to save even more money.

How to Fold Up a Pop Up Tent (In 4 Easy Steps!)

All campers must be able to pitch a tent, thus learning how to do so is essential. In the company of friends, camping out in the wilderness is a memorable experience. The memories made will last a lifetime, even if the experience was not as nice and cozy as you would have preferred. When it comes to taking up the tent, a large percentage of campers have experienced the dreadful feeling. Typically, people collapse the tent and roll it inside the tent bag, however this never results in the tent bag fitting correctly.

See our simple instructions on how to create a DIY camping tent for inspiration if you want to save even more money on your trip.

How To Fold Up a Pop Up Tent (Step-by-step)

Alternatively, you may watch the video below and follow along with the processes given out in the subheadings below, which I have split down into sections.

See also:  How To Waterproof A New Tent

Pre-folding tips

Do yourself a favor and give your shelter a good brushing to get rid of any sand or debris that has accumulated. Some pop-up tents are tiny and light enough to be picked up and shaken, but if you have a dustpan and brush, you can get away with it.

During this procedure, wind is not your friend, and it is quite beneficial to have a second person to assist keep things under control in these scenarios. If you’re on your own, keep some heavy objects close by to assist keep things from blowing away in windy situations.

Step 1 – Make it flat

To make your tent flat, bring the edges of your tent together and tape them together. A symmetrical manner of pressing the shelter together will almost always be the only way it can be done in most cases. If it is refusing to fold the way you want it to, or if it has an unusual form, try pushing it flat along a different axis to see if that helps. Please refer to the graphic below if any of the above terms do not make sense.

Step 2 – Start folding in half

Bring the opposite end towards you, along the axis depicted in the diagram below, while kneeling on one end of the rope.

Step 3 – Fold over to create circles

Roll the end that is heading towards you beneath itself, and you’ll see that a handful of circles develop as a result of your actions. Bring these circles together such that they are stacked on top of one another.

Step 4 – Secure and bag up

The end that is heading towards you should be rolled under itself, and you will observe that a few of circles develop as you do so. Stack these circles on top of one another so that they are level.

Other pop up tents

If you have a pop up camping tent (as opposed to a simple pop up tent), the principle is quite similar, with the exception that you want to make a burrito shape first, and then pull the two ends together, which will automatically fold into circles as a result of the natural folding. Take a look at this guy demonstrating to his tent who is in charge.

How to Fold Up a Pop Up Tent

Documentation Download Documentation Download Documentation A surprising number of individuals utilize pop-up tents as quick and simple shelters, but discover that folding the tent is an unanticipated headache. Folding the tent poles together and then over each other is the best method for storing it. Using this method, you can collapse the tent into a circle that can be stored in a bag until you need it again. With a little understanding of tent folding procedures, you’ll be able to store your tent until you need it again.

  1. 1 Before you begin folding the tent, clean it well. In most cases, shaking out dirt, sand, and pine needles is all that’s required of you. Despite the fact that you can try again later, the debris may become lodged in the tent folds. Tip the tent to the side to allow the debris to drain. When you have the opportunity, thoroughly clean the tent using a little amount of powdered laundry detergent and a damp towel.
  • Never put away a wet tent, otherwise you’ll wind up with mold on your hands
  • It’s important to never pack away a wet tent since you’ll get mold.
  • Never put away a wet tent, otherwise you’ll wind up with mold on your hands.
  • You won’t require more than a minimal amount of force to draw the tent down because of the lightweight nature of the poles. The poles are also flexible, making it unlikely that they would break.
  1. You won’t require more than a minimal amount of force to draw the tent down because of the lightweight poles. In addition, because the poles are flexible, they are less prone to break.
  1. Because the poles are lightweight, you will only only a small amount of force to draw the tent down. The poles are very flexible, making it unlikely that they would break
  • When washing away difficult stains, a small amount of powdered detergent might be beneficial.
  • 2 Grab the tent’s sides with both hands. Position yourself in front of the tent’s entrance. The tent pole that runs from side to side above the entrance is the one that is closest to you. Grab hold of both edges of the tent with both hands. Even if the door has a cover on it, leave the door open.
  • 2. Hold onto the tent’s edges. Position yourself so that you are facing the tent’s front door. The tent pole that runs from side to side above the entrance is the one that is closest to the tent and is the longest. Squeeze the tent’s sides together with both hands. If the door has a cover on it, leave it open.
  • 2 Take hold of the tent’s edges. Place yourself in front of the tent’s entrance. The tent pole that runs from side to side above the entrance is the one that is the closest. Grab both edges of the tent with both hands. If the door has a cover on it, leave it open
  • Because the poles are extremely flexible, there is no need to be concerned about them breaking.
  1. Do not be concerned about the poles breaking because they are quite flexible.

The poles are quite flexible, so there is no need to be concerned about them breaking.

  • Because the poles are quite flexible, you shouldn’t be concerned about them breaking.

Inquire about something There are 200 characters remaining. Include your email address so that you may be notified when this question has been resolved. SubmitAdvertisement

  • Inquire about a problem a total of 200 characters are still available Fill up the blanks with your email address to be notified when your query is answered. SubmitAdvertisement

Inquire about something. There are just 200 characters remaining. Include your email address so that you may be notified when this question has been answered. SubmitAdvertisement

About This Article

Pose a Question There are 200 characters remaining on the page. Include your email address so that you may be notified when this question is answered. SubmitAdvertisement

Did this article help you?

Pop-up tents, as the name indicates, are tents that essentially build themselves up. Simply pull them out of their bag and, poof!, you have a completely functional shelter on your hands in a matter of seconds. Folding a pop-up tent and cramming it back into its bag, on the other hand, is a very other story. Learn how to fold a pop up tent step by step in the video below. We also provide some helpful folding hints and a video to make learning the process that much easier! Whether you’re looking for the fundamentals of folding a pop-up camping tent, a play tent, or a beach pop-up tent, we’ve developed a list of general guidelines to follow to assist you in your endeavor.

Keep in mind that the directions provided below may not be applicable to your specific tent. However, because most pop-up tents fold in a similar manner, even if your tent is different from other conventional tents, you should be able to get a basic sense of what to do from our instructions.

Pre-Folding Tips

  • It is not a good idea to fold a filthy tent since it might cause harm to the material during storage and attract insects. Consequently, be sure to clean up any waste and sweep off any dirt or debris. You may completely clean the tent by using a damp sponge or moist cloth soaked in water and mild soap to remove stains or mud splashes from the surface. Try to do so before the stains or mud have had a chance to completely dry, as you will be able to wash them more easily when they are still wet. Alternatively, if your tent is in desperate need of a thorough cleaning, consult our tutorial on how to clean a tent for our specific step-by-step procedure
  • Allowing the tent to dry and air out is recommended prior to packing it up. When you fold a damp tent, you risk causing damage and mold growth. As long as it is not filthy or soaked, you should at the very least allow it to air out for an hour before packing it up.
  • Untether the tent: You will not be able to begin folding the tent until the tent has been untethered. Make sure you pull out all of the metal stakes that hold your tent to the ground before you begin packing it up. After removing the stakes, wash and dry them thoroughly before storing them in your tent bag.
  • Remove the tarp: If your tent is equipped with a tarp or secondary covering for sun and rain protection, remove it, fold it, and place it in the bag with the rest of your belongings.

Important: It is critical that you follow the washing and drying instructions, especially if you are not planning to use your tent for an extended period of time. If you don’t follow these instructions, you’ll most likely wind up with a rotting tent. Yikes! Following the completion of all of the pre-folding measures, you can begin folding the pop-up tent in its entirety. For even more thorough preparation, let’s watch a brief take-down video and then walk through each step together.

Folding a Pop Up Tent Video

Important: It is critical that you follow the washing and drying instructions, especially if you are not planning to use your tent for an extended period of time. a. It is quite probable that you will wind up with a moldy tent if you do not follow these instructions carefully. Yikes! You may begin folding the pop-up tent now that you’ve completed all of the pre-folding preparations. Watching a fast take-down video and then going through each step can help you prepare even more effectively.

Step 1: Grab the two top points of the tent and bring them together.

Important: It is critical that you follow the washing and drying instructions, especially if you do not intend to use your tent for an extended period of time. If you don’t follow these instructions, you’ll most likely wind up with a rotten tent. Yikes! Following the completion of all of the pre-folding measures, you can begin folding the pop-up tent. Take a look at this incredibly brief take-down video and then work through each step to enhance your preparedness.

Step 2: Grab the back end of your tent and fold it to meet the middle.

Important: It is absolutely necessary to follow the washing and drying procedures, especially if you are not planning to use your tent for an extended period of time. If you neglect these procedures, you will almost certainly wind up with a moldy tent. Yikes! Now that you’ve completed all of the pre-folding measures, you may begin folding the pop-up tent. To go even farther in our preparation, let’s watch a very short take-down video and then walk through each step.

Step 3: Bring the front arch together to meet the other points.

It is just as important to have your tent door open to allow for air circulation as it is to have an accessible entry point while folding your tent up to allow any trapped air to escape. Grab the top of the arch above the entrance with your free hand and hold it in place. Once this is done, fold the front of the tent inwards towards the remainder of the tent. When you’re finished, your pop-up tent should have the shape of a taco on it.

Step 4: Stand your tent upright and fold it inwards.

Turn your tent upwards with one hand while retaining a tight grasp on the pole. In the next step, use your free hand to gently lower the tent’s highest point all the way down to the ground. During this time, the tent should begin to shut in on itself, while the arches in your other hand should stay on the outside.

Step 5: Twist the tent to form two circles, then fold them over each other.

Turn your tent upwards while keeping a tight grasp on it with one hand. Using your free hand, push the tent’s highest point all the way down to the ground until it is level. During this time, the tent should begin to shut in on itself, while the arches in your other hand should remain on the outside.

Step 6: Secure the tent if it has such features.

In the event that your pop-up tent is one of the numerous kinds that has secure attachments to prevent it from springing open, you may take use of that feature right away.

If your tent does not have any of these qualities, make sure to hang on to it tightly until you have it stowed where you will use it.

Step 7: Place the tent back into its bag.

The secure attachments that come with your pop-up tent to prevent it from popping up may now be used if your tent is one of the numerous versions that have them. If your tent does not have any of these qualities, make sure to hang on to it tightly until you have it stowed where you will use it again.

How To Fold A Pop Up Tent

Pop-up tents are notoriously naughty, as we all know. You can set them up in seconds, but every time you try to fold one back up, it either fires out again or doesn’t fit back into the bag because it was folded improperly, giving you unending stress when packing up your camping goods. Now you don’t have to suffer anymore! You will learn how to fold your pop up tent in a few simple steps with the help of this instruction.

Folding Your Pop Up Tent: Step By Step Guide

Pop-up tents are notorious for their mischievous behavior. You can set them up in seconds, but every time you try to fold one back up, it either fires back out or doesn’t fit back into the bag because it was folded improperly, giving you unending agony when packing up your camping goods. No longer will you be in pain. A few simple actions will be demonstrated in this tutorial to folding your pop up tent.

Step 1: Unzip the door

Unzip the front entrance of your tent from the inside by walking to the front of it. This allows any trapped air to exit the tent, making it simpler to compress and fold later down the road. You may also want to consider giving the tent a quick clean down at this point to ensure that it isn’t soiled for the next time you use it.

Step 2: Fold from back to front

Take hold of the center of the rear base pole and proceed to fold it upwards until you reach the top of the pole. Take both of them in one hand and hold them together. Then, while still holding the two poles in place, reach over and grasp the front base pole, pulling it upright until it meets the other poles you’re presently holding, bringing all of the poles together in one hand for easy storage.

Step 3: Lift the tent and rotate

Begin to fold upwards from the center of the rear base pole, all the way until you reach the roof pole. With one hand, grasp both of them tightly. Then, while still holding the two poles in place, reach over and grasp the front base pole, pulling it upright until it meets the other poles you’re presently holding, bringing all of the poles together in one hand for easy transport.

Step 4: Pull down

Grab the top section of the tent with your free hand and pull it down towards your feet.

Step 5: Slide rings

The tent frame should be slightly overlapping two circles now that you’ve folded it towards the soles of your feet, as seen in the image below. Slide one ring beneath the other, then press down on the tent to allow any residual air to escape through the opening. The tent should now be folded in half so that it forms a circle.

Step 6: Bag it up

Take any slack elastic straps and draw them across the folded tent, allowing you to stow the tent away in its accompanying bag when you’ve completed this step.

That’s all there is to it! Your tent should be completely folded and ready to depart at this point. If you’re still having trouble figuring out how to fold a pop up tent, you might find our video instruction below to be more helpful.

Folding A Pop Up Tent: Video Guide

Thank you for taking the time to read our advice on how to fold a pop-up tent. If you found this article useful and would want to read more pieces like this, have a look at some of our other camping-related content.

How To Correctly Pack Away Your Tent

It has been a pleasure providing you with this information on how to fold a pop-up tent! Visit some of our other camping-related articles if you enjoyed this one and would like to read more posts like this.

Why is it so important to pack your tent away properly?

Thank you for taking the time to read our article on how to fold a pop-up tent. Visit some of our other camping-related articles if you like this and would want to read more pieces like this.

Dry your tent before it’s packed away

In the United Kingdom, if you’ve gone camping, there’s a good possibility you’ve seen a little amount of rain throughout your camping trip. If you were very unlucky, you may have even had to pack up your tent in the rain, which is never a pleasant experience. It’s also not very good for your tent’s structure. There is a considerable probability that your tent will be coated with mould or mildew when you next take it out of its bag if it is left damp in its bag after a rainstorm. This may necessitate a complete cleaning of the tent, which may cause your camping trip to be postponed or cancelled altogether.

See also:  Where Can I Buy A Tent

Ensure that the entire tent is dry, including locations such as the pegging points and guy lines, before using it.

Check for rips, tearsbreaks

Even if you’ve spent your camping trip in the United Kingdom, there’s a good possibility you’ve experienced some rainfall. The worst case scenario would be that you had to pack up your tent in the rain, which is never a pleasant experience. It’s also not very good for your tent’s structural integrity or durability. There is a strong risk that your tent will be coated with mould or mildew when you take it out of its bag if you keep it damp in its bag. Due to the fact that you will have to clean the tent completely, your camping trip may be postponed for a period of time.

Check that the whole tent, including locations such as the pegging points and guy lines, is dry before setting up.

Fold or roll your tent properly

Although it may be tempting to just stuff your tent into its bag, doing so would cause more harm than good. You might end up damaging both the tent and the bag, which would need the purchase of a whole new tent. It may also alter the natural form of the tent, making it more difficult to set up the next time it is pitched.

Bag pegs and poles

Your tent pegs and poles should each come with a little bag in which to store them, and this bag is there for a reason: it keeps them organized. Make sure to put all of your pegs and poles (as well as anything else that could be a little pointy) in their proper bags, otherwise they may cause harm to your tent when it’s time to pack it up.

You don’t want to penetrate the tent after thoroughly inspecting it or after purchasing it brand new. If you can’t find the bags, use whatever you have on hand to wrap them up and protect your tent from the sharp edges of the sharp spikes.

How to care for a tent – Tent Tips

  • Make sure to open up your tent and let it air out for a couple of hours before putting it down. You’ll need to sweep and clean the interior of your tent to remove any debris, dust, and filth that has collected within. Keep the tent doors slightly open while folding it up to allow for some air to flow through
  • Don’t completely close the tent doors when folding it up. Campers’ best friend is duct tape, so make sure you have some on hand for mending holes or tiny tears, as well as for securing poles until you can acquire a replacement. Footprints: a groundsheet that may be removed to protect the underside of your tent from damp ground or debris
  • In the event of a leaky seam, just cover it with sealant and allow it to soak into the material
  • Seam sealant When storing the tent, avoid laying it on its side since this might cause damage to the poles. Instead, lie it level.

Open it up and let it air out for a couple of hours before putting your tent away for the day. You’ll need to sweep and clean the interior of your tent to remove any debris, dust, and filth. Keep the tent doors slightly open while folding it up to allow for some air to flow through; don’t completely close the tent doors when storing it. Campers’ greatest friend is duct tape, so make sure you have some on hand for mending holes or tiny tears, as well as for securing poles until you can acquire a new one.

In the event of a leaky seam, just cover it with sealant and allow it to soak into the material; seam sealant: In order to prevent damage to the tent’s poles, avoid storing it on its end.

(2022) How to Fold a Tent: Tips on Packing Away and Caring for Your Tent

The ability to do a number of wilderness and outdoor abilities that are both fundamental and essential is a must-have. You can think of things like basic navigation, obtaining food, and securing water as examples. Apart from the above listed talents, learning how to fold a tent is a fundamental skill that you should have or learn if you love spending time in the outdoors or if you want to be prepared for an emergency. There are many different types of tents available today, and the best way to pack them away will depend on a variety of circumstances.

However, the gist of it is that it is a talent that is simple to learn and one that is extremely valuable.

Tents vs other forms of shelter

Tents are the most common type of shelter whether camping or hiking in the great outdoors. Sure, it isn’t the most space-saving option, and it isn’t the most convenient to put up and disassemble either. Tents, on the other hand, are undoubtedly the greatest total package. They give a high level of protection from the elements in the absence of an RV or a cabin when camping or hiking in the woods. These will also typically have adequate space to handle the equipment as well as the individuals who will be staying inside throughout the event.

Tents, on the other hand, are still the most popular choice.

Lean to

The lean to is extremely straightforward. It is, by definition, a temporary structure that makes use of an existing structure as a support pillar to provide stability. It is extremely popular among minimalists and survivalists since it can be constructed in the woods with little or no extra supplies that are not readily available in the outdoors. A rock or tree can serve as a basis of support, and the roof material might be made of tarps or locally grown vegetation that has been securely fastened.

Survivists appreciate it because it can be constructed with a minimal amount of raw resources.

Furthermore, it will take a significant amount of time to construct a suitable one. Furthermore, because you’re walking on natural flooring, you’ll get wet more frequently than not if it rains.

Tarp

Shelters made of tarps are quite simple to erect. As with the lean to, all that is required is a basis of support, such as a tree, and then with rope, you can easily connect the tarp to these bases, and you have yourself a roof to enjoy. For more information about tarp camping, please see our tips and techniques section. For hot days or mild rain, this is an excellent option. Despite this, because to the lack of walls and floors, you are more prone to getting wet during moderate to severe rainfall.

Water Proof Bivys

These are essentially reinforced sleeping bags that include a waterproof layer on the inside that you can utilize to keep you safe from the weather. This is a clear approach that has some virtues in my opinion. It is portable and can be put up almost anywhere, and it requires minimal work to prepare and take down. In terms of actual floor area, though, there isn’t much to be had. If you suffer from claustrophobia, this is not a suitable solution for you. Aside from that, your pack is most likely going to be sitting outdoors in the open.

If it’s raining, you won’t be able to do so without getting your clothes wet on the inside.

One of the downsides of using a tent as opposed to these other forms of shelter is the amount of time it will take to put up and take down the tent, as well as the fact that tents are typically more bulky than other types of protection.

Why is learning to fold a tent important?

A decent-quality tent can cost you back upwards of $100 in materials and labor. Any camper’s first goal should be to ensure that their equipment lasts as long as feasible. One of the ways to accomplish this is to make certain that your tent is properly packed away. Long treks and continuous usage can be taxing on not just you, but also on your equipment, which might result in premature failure. If you don’t take care when you’re packing up your tent, you run the danger of causing significant damage to it much sooner.

Speed takes practice

A decent-quality tent can set you back upwards of $100, at the most. If you’re a camper, keeping it in good condition for the longest amount of time should be a high priority. To do this, make certain that your tent is properly packed up at the end of the night. Long treks and prolonged usage may be taxing on not only you, but also on your equipment, which might result in premature failure. By not being careful when you pack up your tent, you increase the likelihood of it becoming damaged much sooner.

Space Maximization

A decent-quality tent will cost you upwards of $100. Any camper’s top goal should be to ensure that their equipment lasts as long as possible.

One method to accomplish this is to make certain that your tent is neatly packed away. Long treks and prolonged usage may be taxing on not just you, but also your equipment. If you don’t take care when you’re packing up your tent, you run the danger of destroying it much sooner than you should.

The Best Way to pack a tent?

It’s an age-old point of contention. Experienced hikers and campers are present, and they all have differing perspectives on this. What is the best method to pack up a tent? Is it better to fold, roll, or stuff? There is probably no one optimal approach to pack up your tent, which is the long and short of the situation. When it comes to storing your outdoor shelter, each situation will be evaluated on an individual basis.

Folding and Rolling

Historically, there has been much discussion about this topic. Experienced hikers and campers are present, and they all have differing perspectives on the matter. In what manner should a tent be folded up and stored? Which method should I use? Folding, rolling, or stuffing There is no one optimal technique to put away your tent, which is probably the long and short answer. When it comes to putting your outdoor shelter away, it will depend on the circumstances.

Stuffing

It is an age-old point of contention. You’ve got a diverse group of hikers and campers with varying perspectives on this. How do you pack up a tent? Do you want to fold, roll, or fill it? The long and short of it is that there isn’t a single optimal technique to pack up your tent. When it comes to storing your outside shelter, it will be on a case-by-case basis.

Packing up a Tent

It’s a long-running argument. You’ve got seasoned hikers and campers who have differing perspectives on this. What is the best method to pack a tent? To fold, roll, or stuff? The long and short answer is that there isn’t a single optimal technique to pack up your tent. When it comes to storing your outdoor shelter, it will depend on the circumstances.

  1. It’s an age-old point of contention. Experienced hikers and campers are present, and they all have differing perspectives on this. What is the best method to pack up a tent? Is it better to fold, roll, or stuff? There is probably no one optimal approach to pack up your tent, which is the long and short of the situation. When it comes to storing your outdoor shelter, each situation will be evaluated on an individual basis.

For those in a hurry or who don’t believe in rolling up their tent, you may pack it inside the bag instead of folding it. Assuming, of course, that the bag is large enough for you to fit the tent inside. The use of a logical approach to packing your tent (like with baggage) helps you to bring it down to a smaller size than if you just shove it all in. It is possible to force it in, but it will likely require some effort on your part.

For Quick-Folding/Pop-up Tents

  1. Remove any pegs that may have been in use. After that, place them in their container or bag. Open the door for me. Take the two poles at the top of the structure and gently fold them down the middle. Following that, take the bottom poles and repeat the process. If there are any air packets, gently open the door and let the air escape. It should be folded in such a way that it resembles a tortilla. At this stage, it should be able to fit inside the bag roughly
  2. Pack up the tent and place it in its bag.

Packing a tent in the rain

Remove any pegs that may have been in use before. Place them in their own container or bag; and Activate the doorknob and let yourself in. Then carefully fold down the middle of both of the top-most poles. Next, take the lower poles and repeat the procedure. If there are any air packets, gently let them out via the door. Then fold it into a tortilla shape to make it more convenient to eat. It should be able to fit into the bag at this stage. Close and secure the tent in its carrying bag.

Tent Care tips

In some respects, your tent will serve as a home away from home for the duration of your trip. With that in mind, you’ll want to make sure that it remains in good shape for as long as possible. With that in mind, here are a few things you can do to take better care of your tent and extend its useful life. 1.

Read the instructions

This may appear to be rather straightforward. However, there are occasions when it is a very easy, yet disregarded method of caring after our possessions.

Manufacturers will always give crucial information to keep in mind when caring for whatever it is that you have purchased from them. They not only constructed it, but they also know how to take care of it. Those who fail to comply face the danger of suffering premature and avoidable harm.

Be gentle in handling poles and zippers

These are the sections of the tent that are most likely to be damaged and cause harm to the tent. When you are overly forceful with the zipper, you run the danger of catching the tent fabric when you attempt to shut it in a fast manner. Abrasion of the cloth occurs when you open the door too rapidly, and if you’re too aggressive, you run the chance of harming the poles as well. When you’re ready to store them, lubricate the ends of the poles and the zippers to prevent them from sticking. This will assist in extending the longevity of these components, and as a result, the lifespan of your tent as well.

Never Store a Wet Tent

If you’re out camping and need to take up your tent while it’s still damp, that’s not an issue. To be quite honest, this is a common occurrence. If, on the other hand, you want to put the tent away for long-term storage once you’ve returned home, you’ll want to make certain that it’s well cleaned. Make certain that it is not damp. The most straightforward explanation is that if you keep a wet tent, it will acquire an unpleasant odor and most likely mildew by the time you take it out again. The second point to mention is that putting moisture on a tent’s fabric might cause the hydrolysis process to begin sooner.

Do Manual Cleaning

Putting a tent in the washing machine is a certain way to have your tent torn apart and ruin your vacation. When it comes to cleaning and drying, the tent’s fabric isn’t designed to survive the rigors of a washing machine, let alone a dryer. Soap and water should be used to clean out your tent in the yard. Remove the filth that has dried on your tent with a non-abrasive sponge or an old toothbrush to gently loosen it. If you see stains that necessitate the use of enzyme cleansers, you will want to keep an eye on them for the time being.

In Conclusion

Listed above are just a few of the considerations you should keep in mind when it comes to storing and caring for your tent. At the end of the day, it is your obligation to ensure that a tent is in good condition for future usage. It doesn’t have to be a time-consuming or exhausting procedure. It will take around half a day to complete the task. So why not go ahead and do it? Check out our evaluations of the best backpacking tents to offer you more options when it comes to picking the ideal one for your needs.

ABOUT THE AUTHOR

Dennis Owens is a graduate of the National Camping School as well as the REI Outdoor School, among other institutions. He understands all there is to know about what equipment to bring, how to arrange your journey in order to be safe, and what to do if you become lost in the mountains. Because he is a walking encyclopedia when it comes to the wilderness, we are fortunate to have Dennis accompany us on our expeditions.

Leave a Comment

Your email address will not be published. Required fields are marked *